ROHM DTA143ZE

-100mA / -50V Digital transistors
(with built-in resistors)
DTA143ZM / DTA143ZE / DTA143ZUA / DTA143ZKA
 Applications
Inverter, Interface, Driver
 Features
1)Built-in bias resistors enable the configuration of an inverter circuit without connecting external input resistors (see
equivalent circuit).
2)The bias resistors consist of thin-film resistors with complete isolation to allow positive biasing of the input. They also
have the advantage of almost completely eliminating parasitic effects.
3)Only the on/off conditions need to be set for operation, making the device design easy.
 Structure
PNP epitaxial planar silicon transistor (Resistor built-in type)
 Dimensions (Unit : mm)
DTA143ZM
DTA143ZE
0.7
1.6
0.55
0.3
0.2
(3)
(2)
0.2
0.4 0.4
0.2
0.13
0.5
(1) IN
(2) GND
(3) OUT
0.8
ROHM : EMT3
DTA143ZKA
2.9
0.7
1.6
2.8
2.1
1.25
0.15
1.3
0.1Min.
(1)
(1) GND
(2) IN
(3) OUT
Each lead has same dimensions
(2)
(1)
0.95 0.95
0.15
ROHM : SMT3
EIAJ : SC-59
1.9
(1) GND
(2) IN
(3) OUT
Each lead has same dimensions
Abbreviated symbol : 113
Abbreviated symbol : E13
 Packaging specifications
Part No.
0.8
(3)
0.65 0.65
ROHM : UMT3
EIAJ : SC-70
1.1
0.4
(3)
(2)
(1) GND
(2) IN
(3) OUT
Abbreviated symbol : E13
0.9
0.2
0.3
0.15
1.0
Abbreviated symbol : E13
2.0
0.2
0.5 0.5
0.3Min.
ROHM : VMT3
DTA143ZUA
(1)
(1)(2)
0.22
0.1Min.
0.8
1.2
0.8
(3)
1.6
1.2
0.32
 Inner circuit
Package
VMT3
EMT3
UMT3
SMT3
Packaging type
Taping
Taping
Taping
Taping
Code
T2L
TL
T106
T146
Basic ordering
unit (pieces)
8000
3000
3000
3000
−
−
−
−
−
OUT
R1
IN
R2
GND(+)
DTA143ZM
DTA143ZE
−
DTA143ZUA
−
−
DTA143ZKA
−
−
OUT
IN
−
GND(+)
−
R1=4.7kΩ, R2=47kΩ
www.rohm.com
c 2009 ROHM Co., Ltd. All rights reserved.
○
1/2
2009.06 - Rev.B
DTA143ZM / DTA143ZE / DTA143ZUA / DTA143ZKA
Data Sheet
 Absolute maximum ratings (Ta=25C)
Parameter
Limits
Symbol
Unit
DTA143ZM DTA143ZE DTA143ZUA DTA143ZKA
Supply voltage
VCC
−50
V
Input voltage
VIN
−30 to +5
V
IO
−100
IC(Max.)
−100
Output current
mA
Power dissipation
PD
Junction temperature
Tj
150
°C
Storage temperature
Tstg
−55 to +150
°C
150
200
mW
 Electrical characteristics (Ta=25C)
Parameter
Input voltage
Output voltage
Input current
Symbol
Min.
Typ.
Max.
VI(off)
−
−
−0.5
VI(on)
−1.3
−
−
VO(on)
−
−0.1
−0.3
V
II
−
−
−1.8
mA
VI=−5V
VCC=−50V, VI=0V
Unit
V
VO=−0.3V, IO=−5mA
IO/II=−5mA/−0.25mA
IO(off)
−
−
−0.5
μA
DC current gain
GI
80
−
−
−
Input resistance
R1
3.29
4.7
6.11
kΩ
Resistance ratio
R2/R1
8
10
12
−
fT ∗
−
250
−
MHz
Output current
Transition frequency
Conditions
VCC=−5V, IO=−100μA
VO=−5V, IO=−10mA
−
−
VCE=−10V, IE=5mA, f=100MHz
∗ Characteristics of built-in transistor
 Electrical characteristic curves
OUTPUT CURRENT : Io (A)
INPUT VOLTAGE : VI(on) (V)
−20
−10
−5
−2
Ta=−40°C
25°C
100°C
−1
−500m
−200m
−100m
−100μ −200μ −500μ −1m −2m
−5m −10m −20m −50m −100m
OUTPUT CURRENT : IO (A)
Fig.1 Input voltage vs. output current
(ON characteristics)
−1
−2m
−1m
−500μ
Ta=100°C
25°C
−40°C
−200μ
−100μ
−50μ
−20μ
−10μ
−5μ
−2μ
−1μ
0
1k
VCC=−5V
500
200
VO=−5V
Ta=100°C
25°C
−40°C
100
50
20
10
5
2
−0.5
−1.0
−1.5
−2.0
−2.5
−3.0
INPUT VOLTAGE : VI(off) (V)
Fig.2 Output current vs. input voltage
(OFF characteristics)
1
−100μ −200μ −500μ −1m −2m
−5m −10m −20m −50m −100m
OUTPUT CURRENT : IO (A)
Fig.3 DC current gain vs. output
current
lO/lI=20
−500m
OUTPUT VOLTAGE : VO(on) (V)
−10m
−5m
VO=−0.3V
−50
DC CURRENT GAIN : GI
−100
Ta=100°C
25°C
−40°C
−200m
−100m
−50m
−20m
−10m
−5m
−2m
−1m
−100μ −200μ −500μ −1m −2m
−5m −10m −20m −50m −100m
OUTPUT CURRENT : IO (A)
Fig.4 Output voltage vs. output
current
www.rohm.com
c 2009 ROHM Co., Ltd. All rights reserved.
○
2/2
2009.06 - Rev.B
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller,
fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of
any of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
R0039A