SDS6011 DC Input 1MHz Schmitt Trigger Optocoupler Description Features The SDS6011 consists of a light emitting diode optically coupled to an output integrated circuit detector. The output circuit integrates an optical coupler and a Schmitt Trigger providing hysteresis for noise immunity and pulse shaping. Optical coupling between the input IR LED and output structure allows for high isolation levels while maintaining low-level DC signal control capability. An open collector output allows further design flexibility. High data date – 1MHz (NRZ) Free from latch up and oscillation Microprocessor compatible Drive Logic compatible output sinks 16mA @ 0.4V Guaranteed on/off threshold hysteresis High common mode rejection ratio Fast switching (100nS typical tR and tF) Wide supply voltage compatibility The SDS6011 comes standard in a miniature 6 pin DIP package. Agency Approvals Applications UL/C-UL: VDE: Logic to Logic Isolator Programmable Current Level Sensor Line Receiver (eliminate noise & transients) A.C. to TTL Conversion (square wave shaping) Digital Programming of Power Supplies Interfacing PCs with Peripherals File # E201932 File # 40035191 (EN 60747-5-2) Absolute Maximum Ratings The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to absolute Maximum Ratings may cause permanent damage to the device and may adversely affect reliability. Schematic Diagram Storage Temperature …………………………..-55 to +150°C Operating Temperature ………………………-40 to +85°C Continuous Input Current ………………………………..60mA Transient Input Current ………………….……………..500mA Reverse Input Control Voltage …………..…………………5V Input Power Dissipation ………………………………100mW Total Power Dissipation ……………………………..400mW Solder Temperature – Wave (10sec)……………….….260°C Solder Temperature – IR Reflow (10sec)….…………..260°C Anode 1 6 VCC Cathode 2 5 Ground Do Not Connect 3 4 VO Ordering Information SDS6011 Part Number Description SDS6011 SDS6011-H SDS6011-S SDS6011-STR 6 pin DIP, (60/Tube) 0.40” (10.16mm) Lead Spacing (VDE0884) 6 pin SMD, (60/Tube) 6 pin SMD, Tape and Reel (1000/Reel) NOTE: Suffixes listed above are not included in marking on device for part number identification © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 1 of 8 SDS6011 H/S/TR Rev 1.00 (10/31/2013) 001664 SDS6011 DC Input 1MHz Schmitt Trigger Optocoupler Electrical Characteristics, TA = 25°C (unless otherwise specified) Parameter Symbol Min. Typ. Max. Units Test Conditions - 1.2 1.5 V IF = 10mA Input Specifications LED Forward Voltage VF 0.75 0.95 - V IF = 0.3mA LED Reverse Voltage BVR 5 - - V IR = 10μA Terminal Capacitance Ct - 50 - pF V=0, f=1KHz Reverse Current IR - - 10 A VR=5V Output Specifications Operating Voltage Supply Current Output Current, High VCC 3 - 15 V - ICC(OFF) - - 3 mA IF=0mA, VCC=5V IOH - - 100 A IF=0mA, VCC=VO=15V ICC(ON) - 1.6 5 mA IF=IF(on), VCC=5V V IF=IF(on), RL=270Ω, VCC=5V mA RL=270Ω, VCC=5V mA RL=270Ω, VCC=5V Coupled Specifications Supply Current Output Voltage, Low VOL - 0.2 0.4 - 1.2 1.6 IF(ON) - - 10 - - 5 IF(OFF) 0.3 0.75 - IF(OFF) / IF(ON) 0.5 - 0.9 Threshold Current, ON -A Option -B Option Threshold Current, OFF Hysteresis Ratio RL=270Ω, VCC=5V Turn On Time TON - 1.2 4 Turn Off Time TOFF - 1.2 4 Rise Time TR - 0.1 - Fall Time TF - 0.1 - - - VRMS RH ≤ 50%, t=1min - - VI-O = 500VDC S VCC=5V, RL=270Ω, IF=IF(ON) Isolation Specifications Isolation Voltage Input-Output Resistance © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 VISO RI-O 5300 10 11 Page 2 of 8 SDS6011 H/S/TR Rev 1.00 (10/31/2013) 001664 SDS6011 DC Input 1MHz Schmitt Trigger Optocoupler SDS6011 Solder Reflow Temperature Profile Recommendations (1) Infrared Reflow: Refer to the following figure as an example of an optimal temperature profile for single occurrence infrared reflow. Soldering process should not exceed temperature or time limits expressed herein. Surface temperature of device package should not exceed 250ºC: G F D E H B A C Process Step A B C D E F G H Description Preheat Start Temperature (ºC) Preheat Finish Temperature (ºC) Preheat Time (s) Melting Temperature (ºC) Time above Melting Temperature (s) Peak Temperature, at Terminal (ºC) Dwell Time at Peak Temperature (s) Cool-down (ºC/s) Parameter 150ºC 180ºC 90 - 120s 230ºC 30s 260ºC 10s <6ºC/s (2) Wave Solder: Maximum Temperature: Maximum Time: Pre-heating: Single Occurrence 260ºC (at terminal) 10s 100 - 150ºC (30 - 90s) (3) Hand Solder: Maximum Temperature: Maximum Time: Single Occurrence © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 350ºC 3s (at tip of soldering iron) Page 3 of 8 SDS6011 H/S/TR Rev 1.00 (10/31/2013) 001664 SDS6011 DC Input 1MHz Schmitt Trigger Optocoupler SDS6011 Package Dimensions 6 PIN DIP Package © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Note: Page 4 of 8 All dimensions in millimeters [mm] with inches in parenthesis () SDS6011 H/S/TR Rev 1.00 (10/31/2013) 001664 SDS6011 DC Input 1MHz Schmitt Trigger Optocoupler SDS6011 Package Dimensions 6 PIN WIDE Lead Space Package (-H) © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Note: Page 5 of 8 All dimensions in millimeters [mm] with inches in parenthesis () SDS6011 H/S/TR Rev 1.00 (10/31/2013) 001664 SDS6011 DC Input 1MHz Schmitt Trigger Optocoupler SDS6011 Package Dimensions 6 PIN SMD Surface Mount Package © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Note: Page 6 of 8 All dimensions in millimeters [mm] with inches in parenthesis () SDS6011 H/S/TR Rev 1.00 (10/31/2013) 001664 SDS6011 DC Input 1MHz Schmitt Trigger Optocoupler SDS6011 Packaging Specifications Tape & Reel Specifications (T&R) B 7.70±0.1 B1 D Note: D1 E 10.46±0.1 ø1.60±0.1 ø1.55±0.05 1.75±0.1 All dimensions in millimeters [mm] K P P1 T W 4.25±0.1 12.0±0.1 4.00±0.1 0.3±0.05 16±0.3 L M N O Q R S 330±2 101.6±1 16.4+0.2 2.0±0.2 R13±0.5 1.50±0.5 R10±1 © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 7 of 8 SDS6011 H/S/TR Rev 1.00 (10/31/2013) 001664 SDS6011 DC Input 1MHz Schmitt Trigger Optocoupler SDS6011 Package Marking SDS6011 Package Weights Single Unit Full Tube (60pcs) Full Pouch (10 tubes) Full Reel (1000pcs) SDS6011(-H) 0.41 44 450 - SDS6011-S 0.40 42 440 - 0.40 - - 880 Device SDS6011-STR Note: All weights above are in GRAMS, and include packaging materials where applicable DISCLAIMER Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO reserves the right to make changes to product description, specifications at any time without further notices. SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO’s Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other warranty, expressed or implied, including merchantability and fitness for particular use. LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be reasonably expected to result in significant injury to the user, or (d) a critical component of a life support device or system whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness. © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 8 of 8 SDS6011 H/S/TR Rev 1.00 (10/31/2013) 001664