SDT600 - Solid State Optronics

SDT600
DC Input
60V
Photo-Transistor Optocoupler
Description
Features








The SDT600 consists of a phototransistor optically coupled
to a light emitting diode. Optical coupling between the
input IR LED and output phototransistor allows for high
isolation levels while maintaining low-level DC signal
control capability. The SDT600 provides an optically
isolated method of controlling many interface applications
such as telecommunications, industrial control and
instrumentation circuitry.
VCEO = 60V
Small 6 pin DIP/SMD package
Low input power consumption
High stability
CTR Range 40 – 320%
High Isolation Voltage (5000VRMS)
Long Life / High Reliability
RoHS / Pb-Free / REACH Compliant
The SDT600 comes standard in a miniature 6 pin DIP
package.
Agency Approvals
Applications
UL/C-UL:
VDE:








Registers, Copiers, Automatic Vending Machines
System Appliances, Measuring Instruments
Computer Terminals, PLCs
Telecommunication Equipment, Telephones
Home Appliances
Digital Logic Inputs
Microprocessor Inputs
Switching Power Supplies
Schematic Diagram
(+) Input
1
6
Base
(-) Input
2
5
Collector
Do Not Connect
3
4
Emitter
File # E201932
File # 40035191 (EN 60747-5-2)
Absolute Maximum Ratings
The values indicated are absolute stress ratings. Functional
operation of the device is not implied at these or any
conditions in excess of those defined in electrical
characteristics section of this document. Exposure to
absolute Maximum Ratings may cause permanent damage
to the device and may adversely affect reliability.
Storage Temperature …………………………..-55 to +125°C
Operating Temperature ………………………-40 to +100°C
Continuous Input Current ………………………………..50mA
Transient Input Current ………………….……………..500mA
Reverse Input Control Voltage …………..…………………6V
Input Power Dissipation …………………………………40mW
Total Power Dissipation ……………………………..200mW
Solder Temperature – Wave (10sec)……………….….260°C
Solder Temperature – IR Reflow (10sec)….…………..260°C
Ordering Information
Part Number
Description
SDT600
SDT600-H
SDT600-S
SDT600-STR
6 pin DIP, (65/Tube)
0.40” (10.16mm) Lead Spacing (VDE0884)
6 pin SMD, (65/Tube)
6 pin SMD, Tape and Reel (1000/Reel)
SDT600
NOTE: Suffixes listed above are not included in marking on
device for part number identification
© 2013 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 1 of 10
SDT600/H/S/TR
Rev 2.10 (01/22/2013)
001548
SDT600
DC Input
60V
Photo-Transistor Optocoupler
Electrical Characteristics, TA = 25°C (unless otherwise specified)
Parameter
Symbol
Min.
Typ.
Max.
Units
Test Conditions
1.2
1.4
V
IF = 20mA
Input Specifications
LED Forward Voltage
VF
-
LED Reverse Voltage
BVR
5
-
-
V
IR = 10μA
Terminal Capacitance
Ct
-
30
250
pF
V=0, f=1KHz
Reverse Current
IR
-
-
10
A
VR=4V
Collector-Emitter Voltage
VCEO
60
-
-
V
IC=10A
Emitter-Collector Voltage
VCOE
6
-
-
V
IE=10A
Collector Dark Current
ICEO
-
-
0.1
A
VCE=20V, IF=0mA
Floating Capacitance
Cf
-
0.6
1.0
pF
V=0, f=1MHz
kHz
VCE=5V, IC=2mA, RL=100-3dB
V
IF=10mA, IC=2.5mA
Output Specifications
Cut-Off Frequency
fC
-
80
-
Saturation Voltage
VCE(sat)
-
0.2
0.4
Rise Time
TR
-
5
-
S
IC=2mA, VCC=5V, RL=100
Fall Time
TF
-
4
-
S
IC=2mA, VCC=5V, RL=100
CTR
40
-
320
%
IF=10mA, VCE=5V
40
-
80
%
IF=10mA, VCE=5V
Coupled Specifications
Current Transfer Ratio
CTR Classification (BINNING)
-A
-B
63
-
125
%
IF=10mA, VCE=5V
-C
100
-
200
%
IF=10mA, VCE=5V
-D
200
-
320
%
IF=10mA, VCE=5V
-E
40
-
320
%
IF=10mA, VCE=5V
5000
-
Isolation Specifications
Isolation Voltage
Input-Output Resistance
Test Circuit: Response Time
© 2013 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
VISO
RI-O
-
10
12
-
VRMS
RH ≤ 50%, t=1min
-

VI-O = 500VDC
Test Circuit: Frequency Response
Page 2 of 10
SDT600/H/S/TR
Rev 2.10 (01/22/2013)
001548
SDT600
DC Input
60V
Photo-Transistor Optocoupler
SDT600 Performance & Characteristics Plots, TA = 25°C (unless otherwise specified)
Figure 1: Forward Current (IF) vs. Temperature (°C)
Figure 2: Collector Power Dissipation (PC) vs. Temperature (°C)
Figure 3: Collector-Emitter Saturation Voltage (VCE(SAT)) vs.
Figure 4: Forward Current (IF) vs. Forward Voltage (VF)
Figure 5: Collector Current (IC) vs. Collector-Emitter
Figure 6: Current Transfer Ratio (CTR) vs. Forward Current (IF)
Forward Current (IF)
Voltage (VCE)
© 2013 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 3 of 10
SDT600/H/S/TR
Rev 2.10 (01/22/2013)
001548
SDT600
DC Input
60V
Photo-Transistor Optocoupler
SDT600 Performance & Characteristics Plots, TA = 25°C (unless otherwise specified)
Figure 7: Relative CTR (%) vs. Temperature (°C)
Figure 8: Collector-Emitter Saturation Voltage (VCE(SAT)) vs.
Temperature (°C)
Figure 9: Collector Dark Current (ICEO) vs. Temperature (°C)
Figure 10: Response Times vs. Load Resistance (RL)
Figure 11: Frequency Response Characteristics
© 2013 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 4 of 10
SDT600/H/S/TR
Rev 2.10 (01/22/2013)
001548
SDT600
DC Input
60V
Photo-Transistor Optocoupler
SDT600 Solder Reflow Temperature Profile Recommendations
(1) Infrared Reflow:
Refer to the following figure as an example of an optimal temperature profile for single occurrence infrared reflow.
Soldering process should not exceed temperature or time limits expressed herein. Surface temperature of device
package should not exceed 250ºC:
G
F
D
E
H
B
A
C
Process
Step
A
B
C
D
E
F
G
H
Description
Preheat Start Temperature (ºC)
Preheat Finish Temperature (ºC)
Preheat Time (s)
Melting Temperature (ºC)
Time above Melting Temperature (s)
Peak Temperature, at Terminal (ºC)
Dwell Time at Peak Temperature (s)
Cool-down (ºC/s)
Parameter
150ºC
180ºC
90 - 120s
230ºC
30s
260ºC
10s
<6ºC/s
(2) Wave Solder:
Maximum Temperature:
Maximum Time:
Pre-heating:
Single Occurrence
260ºC (at terminal)
10s
100 - 150ºC (30 - 90s)
(3) Hand Solder:
Maximum Temperature:
Maximum Time:
Single Occurrence
© 2013 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
350ºC
3s
(at tip of soldering iron)
Page 5 of 10
SDT600/H/S/TR
Rev 2.10 (01/22/2013)
001548
SDT600
DC Input
60V
Photo-Transistor Optocoupler
SDT600 Package Dimensions
6 PIN DIP Package
© 2013 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Note:
Page 6 of 10
All dimensions in millimeters [mm] with inches in parenthesis ()
SDT600/H/S/TR
Rev 2.10 (01/22/2013)
001548
SDT600
DC Input
60V
Photo-Transistor Optocoupler
SDT600 Package Dimensions
6 PIN WIDE Lead Space Package (-H)
© 2013 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Note:
Page 7 of 10
All dimensions in millimeters [mm] with inches in parenthesis ()
SDT600/H/S/TR
Rev 2.10 (01/22/2013)
001548
SDT600
DC Input
60V
Photo-Transistor Optocoupler
SDT600 Package Dimensions
6 PIN SMD Surface Mount Package (-S)
© 2013 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Note:
Page 8 of 10
All dimensions in millimeters [mm] with inches in parenthesis ()
SDT600/H/S/TR
Rev 2.10 (01/22/2013)
001548
SDT600
DC Input
60V
Photo-Transistor Optocoupler
SDT600 Packaging Specifications
Tape & Reel Specifications (T&R)
B
7.70±0.1
B1
D
Note:
D1
E
10.46±0.1 ø1.60±0.1 ø1.55±0.05 1.75±0.1
All dimensions in millimeters [mm]
K
P
P1
T
W
4.25±0.1
12.0±0.1
4.00±0.1
0.3±0.05
16±0.3
L
M
N
O
Q
R
S
330±2
101.6±1
16.4+0.2
2.0±0.2
R13±0.5
1.50±0.5
R10±1
© 2013 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 9 of 10
SDT600/H/S/TR
Rev 2.10 (01/22/2013)
001548
SDT600
DC Input
60V
Photo-Transistor Optocoupler
SDT600 Package Marking
SDT600
YWW
A-E
Date Code
CTR BIN Marking
may or may not be on
device.
Pin 1
DISCLAIMER
Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO
reserves the right to make changes to product description, specifications at any time without further notices.
SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent
licenses nor indemnity are expressed or implied.
Except as specified in SSO’s Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other
warranty, expressed or implied, including merchantability and fitness for particular use.
LIFE SUPPORT POLICY
SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or
death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all
damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be
reasonably expected to result in significant injury to the user, or (d) a critical component of a life support device or system whose failure can be
reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness.
© 2013 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 10 of 10
SDT600/H/S/TR
Rev 2.10 (01/22/2013)
001548