DATA SHEET AS211-334: 0.1 to 4.0 GHz pHEMT SPDT Switch Applications General purpose switch for telecommunications J3 Features P1dB: +30 dBm typical @ 3 V IP3: +43 dBm typical @ 3 V Low insertion loss: 0.3 dB @ 0.9 GHz Low DC power consumption V2 J1 Small footprint, DFN (6-pin, 1.2 x 1.5 x 0.75 mm) package (MSL1, 260 C per JEDEC J-STD-020) J2 V1 S1614 Skyworks Green™ products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of Green™, document number SQ04-0074. J3 1 6 V2 GND 2 5 J1 J2 3 4 V1 Figure 1. AS211-334 Block Diagram Description The AS211-334 is an FET single-pole, double-throw (SPDT) switch for general telecommunications applications. The device features low insertion loss and positive voltage operation with very low DC power consumption. The switch is manufactured in a compact, 1.2 x 1.5 x 0.75 mm, 6-pin Dual Flat No Lead (DFN) package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Figure 2. AS211-334 Pinout – 6-Pin DFN (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200191G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 20, 2014 1 DATA SHEET • AS211-334: SPDT SWITCH Table 1. AS211-334 Signal Descriptions Pin 1 Name J3 Description Pin RF output 4 Name V1 Description Positive control voltage 2 GND Ground 5 J1 RF common/antenna port 3 J2 RF output 6 V2 Positive control voltage Table 2. AS211-334 Absolute Maximum Ratings Parameter Symbol Test Condition Minimum Maximum Units 6 W +8.0 V Input power PIN Control voltage VCTL –0.2 Operating temperature TOP –40 +85 C Storage temperature TSTG –65 +150 C Note: Any frequency >500 MHz, VCTL = 0/7 V Typical Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Electrical and Mechanical Specifications The absolute maximum ratings of the AS211-334 are provided in Table 2. Electrical specifications are provided in Table 3. The state of the AS211-334 is determined by the logic provided in Table 4. Typical performance characteristics of the AS211-334 are illustrated in Figures 3 through 5. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 June 20, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200191G DATA SHEET • AS211-334: SPDT SWITCH Table 3. AS211-334 Electrical Specifications (Note 1) (Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Insertion loss IL 0.1 to 1.0 GHz 1.0 to 2.0 GHz 2.0 to 3.0 GHz 3.0 to 4.0 GHz Isolation ISO 0.1 to 1.0 GHz 1.0 to 2.0 GHz 2.0 to 3.0 GHz 3.0 to 4.0 GHz Voltage Standing Wave Ratio VSWR Low frequency to 4 GHz Switching characteristics: Rise, fall On, off Min Typical Max Units 0.3 0.4 0.5 0.6 0.5 0.6 0.7 0.8 dB dB dB dB 1.2:1 10/90% or 90/10% RF 50% control to 90/10% RF TRISE = 1 ns, bandwidth = 500 MHz Video feedthrough 1 dB input compression point IP1dB rd 3 Order Input Intercept Point VCTL = 0 and 3 V, 0.5 to 3.0 GHz VCTL = 0 and 5 V 0.5 to 3.0 GHz IIP3 ΘJC Control voltage: Low High VCTL_L VCTL_H 1.3:1 – 10 ns 20 ns 25 mV +30 dBm +34 dBm +43 +50 dBm dBm 25 °C/W Two-tone PIN = +5 dBm VCTL = 0 and 3 V VCTL = 0 and 5 V Thermal resistance dB dB dB dB 25 22 23 26 22 20 20 23 VCTL_L = 0 to 0.2 V @ 20 μA max. VCTL_H = 3 V @ 100 μA max. to 5 V @ 200 μA max. Note 1: Performance is guaranteed only under the conditions listed in this table. Typical Performance Characteristics (VCTL = 3 V, CBL = 47 pF, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) 0 0 –0.1 –5 –10 –0.3 Isolation (dB) Insertion Loss (dB) –0.2 –0.4 –0.5 –0.6 –0.7 –15 –20 –25 –0.8 –30 –0.9 –35 –1.0 0 0.5 1.0 1.5 2.0 2.5 3.0 Frequency (GHz) Figure 3. Insertion Loss vs Frequency 3.5 4.0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Frequency (GHz) Figure 4. Isolation vs Frequency Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200191G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 20, 2014 3 DATA SHEET • AS211-334: SPDT SWITCH 2.0 1.9 1.8 VSWR 1.7 1.6 1.5 1.4 1.3 1.2 1.1 1.0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Frequency (GHz) Figure 5. VSWR vs Frequency Table 4. AS211-334 Truth Table Note: V1 (Pin 4) V2 (Pin 6) 0 VHIGH VHIGH 0 J1 to J2 Path J1 to J3 Path Insertion loss Isolation Isolation Insertion loss VHIGH = +3 V to +5 V. “0” = 0 V to +0.2 V. Any state other than described in this Table places the switch into an undefined state. An undefined state will not damage the device. Evaluation Board Description Package and Handling Information The AS211-334 Evaluation Board is used to test the performance of the AS211-334 SPDT Switch. An assembly drawing for the Evaluation Board is shown in Figure 6. The Evaluation Board schematic diagram is provided in Figure 7. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. Package Dimensions The PCB layout footprint for the AS211-334 is provided in Figure 8. Typical case markings are shown in Figure 9. Package dimensions for the 6-pin DFN are shown in Figure 10, and tape and reel dimensions are provided in Figure 11. The AS211-334 is rated to Moisture Sensitivity Level 1 (MSL1) at 260 C. It can be used for lead or lead-free soldering. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. For packaging details, refer to the Skyworks Application Note, Discrete Devices and IC Switch/Attenuators Tape and Reel Package Orientation, document number 200083. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 June 20, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200191G 1.000 0.500 0.000 DATA SHEET • AS211-334: SPDT SWITCH 0.125 THRU V2 J3 * J1 * J2 * V1 SK39653 2.000 Dimensions are in millimeters S1837 Figure 6. AS211-334 Evaluation Board Assembly Diagram CBL RF Output 1 2 CBL RF Output 3 J3 V2 GND J1 J2 V1 6 5 Positive Control Voltage CBL 4 RF Common/Antenna Port Positive Control Voltage S1613 Figure 7. AS211-334 Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200191G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 20, 2014 5 DATA SHEET • AS211-334: SPDT SWITCH 6X 0.20 Pitch 0.50 Detail A 0.05 Metal Land Pad Solder Mask Opening 0.33 0.23 0.55 0.65 Detail A 6X Scale = 60X S1616 Figure 8. AS211-334 PCB Layout Footprint (Top View) Pin 1 Indicator F Device Marking Figure 9. Typical Part Markings (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 June 20, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200191G DATA SHEET • AS211-334: SPDT SWITCH 1.20 C A Seating Plane 0.02 +0.03/–0.02 Pin 1 Indicator C’0.10 B Pin 1 Indicator 4 1 0.50 Pitch 1.50 6 0.05 C 2X 6X 3 3 A 0.05 C 2X 0.75 + 0.05/–0.04 0.05 C 0.05 C Top View Side View Bottom View 5 0.10 M C A B 0.2 ± 0.05 0.4 ± 0.075 Detail A All measurements are in millimeters. Dimensioning and tolerancing according to ASME Y14.5M-1994. Coplanarity applies to the terminals and all other bottom surface metalization. Dimension applies to metalized terminal. If the terminal has a radius on its end, the width dimension should not be measured in that radius area. Scale: 100X 6 Places S3037 Figure 10. AS211-334 6-Pin DFN Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200191G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 20, 2014 7 DATA SHEET • AS211-334: SPDT SWITCH 2.00 ± 0.05 4.00 ± 0.10 4.00 ± 0.10 1.75 ± 0.10 ø1.50 +0.10 3.50 ± 0.05 B 0.30 ± 0.05 (T) R0.30 Max 1.40 ± 0.10 (Bo) A A 1.00 ± 0.10 (Ko) 8.0 + 0.30 –0.10 B Pin 1 Indicator ø0.76 +0.10 Section B 1.70 ± 0.10 (Ao) Notes: 1. Carrier tape: black conductive polystyrene or polycarbonate. 2. Cover tape: transparent conductive material. 3. ESD surface resistivity shall meet GP01-D232. 4. Ao and Bo measurement point is 0.30 mm from bottom pocket. 5. 10-sprocket hole pitch cumulative tolerance: ±0.20 mm. 6. All dimensions are in millimeters. R0.30 Max Section A Figure 11. AS211-334 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 June 20, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200191G Y1045 DATA SHEET • AS211-334: SPDT SWITCH Ordering Information Model Name AS211-334: SPDT Switch Manufacturing Part Number AS211-334 Evaluation Board Part Number AS211-334 EVB Copyright © 2008-2009, 2012, 2014 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200191G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 20, 2014 9