DATA SHEET SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End Applications Product Description The SE2614BT is a complete 802.11bgn WLAN RF front-end module providing all the functionality of the power amplifier, power detector, SP3T Switch and 50 ohm matching on all RF ports in an ultra compact form factor. IEEE802.11b DSSS WLAN IEEE802.11g,n OFDM WLAN Access Points, PCMCIA, PC cards Features Dual Mode IEEE802.11b, IEEE802.11g, IEEE802.11n Integrated PA, TX Filter, SP3T switch Integrated Positive Slope Power Detector 20 dBm Output Power, 802.11b, 11 Mbps 18 dBm @ 3.0 % EVM, 802.11g, 3.3V Lead free, halogen free and RoHS compliant Small plated package, 3 mm x 3 mm x 0.6 mm, MSL 1 The SE2614BT is designed for ease of use, with all the critical matching and harmonic filtering integrated. The SE2614BT also includes a transmitter power detector with 20 dB of dynamic range and a digital enable control for transmitter power on/off control. The power ramp rise/fall time is 0.1 μs typical. Ordering Information Part No. Package Remark SE2614BT SE2614BT-R SE2614BT-EK1 20 lead QFN 20 lead QFN N/A Samples Tape & Reel Evaluation kit Functional Block Diagram Figure 1: Functional Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014 1 DATA SHEET SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End Pin Out Diagram Figure 2: SE2614BT Pin Out (Top View Through Package) Pin Out Description Pin Name 1 DET 2 EN 3 Description Pin Name Description Power Detector output 11 CPORT2 Switch Control Logic – Port 2 path TX Enable 12 CPORT1 Switch Control Logic – Port 1 path VCC0 Supply Voltage – Pre-driver & Driver 13 GND 4 TXIN TX input 14 ANT Antenna Output 5 GND Ground 15 GND Ground 6 GND Ground 16 GND Ground 7 PORT1 Port 1 – May be used for RX or BT 17 GND Ground 8 GND Ground 18 Vcc3 Supply Voltage Power Stage 9 PORT2 Port 2 – May be used for RX or BT 19 GND Ground 10 CTX Switch Control Logic – TX path 20 Vcc2 Supply Voltage Ground Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014 2 DATA SHEET SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End Absolute Maximum Ratings These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected workstations. Symbol Min. Max. Unit Supply Voltage on VCC -0.3 3.6 V VIN DC input on EN, CTX, CPORT1, CPORT2 -0.3 3.6 V TX RF Input Power. - 12.0 dBm TA Operating Temperature Range -40 85 °C Storage Temperature Range -40 150 °C - 1 KV VCC TSTG ESD HBM Definition JEDEC JESD22-A114 all pins to Ground Recommended Operating Conditions Symbol TA VCC Parameter Min. Typ. Max. Unit Ambient temperature -40 25 85 °C VCC0, VCC2, VCC3, supply voltage 3.0 3.3 3.6 V DC Electrical Characteristics Conditions: VCC = EN = 3.3 V, TA = 25 C, as measured on Skyworks Solutions’ SE2614BT-EK1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted Symbol Parameter Conditions Min. Typ. Max. Unit ICC-G Total Supply Current POUT = 18 dBm, 54 Mbps OFDM signal, 64QAM - 160 - mA ICC-B Total Supply Current POUT = 20 dBm, 11 Mbps CCK signal, BT = 0.45 - 190 - mA ICQ Total Supply Current No RF - 90 - mA Icntl Control Line Current CTX, CPORT2, CPORT1 = 3.3V 1 10 μA ICC_OFF Total Supply Current No RF Applied, EN = CTX = CPORT1 = CPORT2 = 0 V 1 10 μA - Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014 3 DATA SHEET SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End PA Logic Characteristics Conditions: VCC = EN = 3.3 V, TA = 25 C, as measured on Skyworks Solutions’ SE2614BT-EK1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VENH Logic High Voltage (Module On) - 1.6 3.3 3.6 V VENL Logic Low Voltage (Module Off) - 0 - 0.4 V IENH Input Current Logic High Voltage - - 330 400* μA IENL Input Current Logic Low Voltage - - 2 10 μA *due to on chip pulldown resistor Switch Logic Characteristics Conditions: VCC = EN = 3.3 V, TA = 25 C, as measured on Skyworks Solutions’ SE2614BT-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol VCTL_ON VCTL_OFF Parameter Conditions Min. Typ. Max. Unit - 1.6 3.3 3.6 V - 0.0 - 0.4 V 200 - nSec - 1 pF Control Voltage (On State) Control Voltage (OFF State) Tswitch T/R Switching Speed CCTL Control Input Capacitance VCTL_OFF -> VCTL_ON VCTL_ON -> VCTL_OFF - - Switch Control Logic Table Allowed Switch Logic CPORT1 CPORT2 CTX PORT1 – ANT PORT2 – ANT TX-ANT ON OFF OFF ON OFF OFF OFF ON OFF OFF ON OFF OFF OFF ON OFF OFF ON All Other States Not Supported Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014 4 DATA SHEET SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End AC Electrical Characteristics 802.11g/n Transmit Characteristics Conditions: VCC = EN = CTX = 3.3 V, CPORT1 = CPORT2 = 0 V, TA = 25 C, as measured on Skyworks Solutions’ SE2614BT-EK1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FIN POUT ACPR, IEEE Mask P1dB S21 Parameter Condition Min. Typ. - 2400 - 2500 MHz Output Power 54 Mbps OFDM signal, 64 QAM, 3% EVM - 18 - dBm Spectral Mask POUT = 20 dBm, 11 Mbps CCK, BT = 0.45 11 – 22 MHz 22 – 33 MHz - - dBc Frequency Range -35 -55 Max. Unit P1dB - - 25 - dBm Small Signal Gain - - 30 - dB +1.5 dB Small Signal Gain vs Temp Measured at single freq from -40°C to 85°C Small Signal Gain Variation Gain variation over single 40MHz channel Gain Variation over band - 0.5 - - 1.1 - Gain @ limit 3.2Ghz 3206 to 3312 MHz - 10 15 dB Harmonics POUT = 20 dBm, 1 Mbps, DSSS - -50 -45 dBm/MHz - -50 -45 dBm/MHz tdr, tdf Delay and rise/fall Time 50 % of VEN edge and 90/10 % of final output power level - 0.2 - μs S11 Input Return Loss - 10 - dB ∆S21_T ∆S21 S213.2 2f 3f STAB RU - -1.5 dB Stability CW, POUT = 20 dBm 0.1 GHz – 20 GHz Load VSWR = 6:1 All non-harmonically related outputs less than -42 dBm/MHz Ruggedness PIN = 12dBm, Load VSWR = 6:1 No permanent damage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014 5 DATA SHEET SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End Receive and BT Characteristics Conditions: VCC = 3.3 V, EN = CTX = 0 V, TA = 25 C, as measured on Skyworks Solutions’ SE2614BT-EK1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FOUT Parameter Frequency Range Condition Min. Typ. - 2400 - 2500 Unit MHz dB CPORT1 = 0 V and CPORT2 = 3.3 V or CPORT1 = 3.3 V and CPORT2 = 0V - 1.2 - PORT1 or PORT2 15 20 - - - 1.2 - PORT1 or PORT2 15 20 - dB 200 250 nSec 25 - dB RXIL Insertion Loss RXRL Return Loss BTIL Insertion Loss BTRL Return Loss Ton/off T/R on/off switching speed Switching speed between T/R modes. Vcc0=3.3V. Isolation between ANT and PORT1/PORT2 Difference in signal level on PORT1 or PORT2 when transmitting from TX. CTX = 3.3V, CPORT1 = CPORT2 = 0V PORT1 and PORT2 terminated in 50ohm. ANTRISOL Max. - dB Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014 6 DATA SHEET SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End Power Detector Characteristics Conditions: VCC = EN = CTX = 3.3 V, CPORT1 = CPORT2 = 0 V, TA = 25 C, as measured on Skyworks Solutions’ SE2614BT-EK1 evaluation board, unless otherwise noted. Symbol Parameter Condition Min. Typ. Max. Unit - 2400 - 2500 MHz FOUT Frequency Range PDR Power detect range, CW Measured at ANT 0 - 21 dBm PDVNoRF Output Voltage, POUT = No RF Measured into 26KΩ - 0.35 - V PDVP18 Output Voltage, POUT = 18 dBm CW Measured into 26KΩ - 0.68 - V PDVP21 Output Voltage, POUT = 22 dBm CW Measured into 26KΩ - 0.83 - V Detector output impedance Zout LPF-3dB 1 Power detect low pass filter -3dB corner frequency PDCLOAD = High Z (1MΩ) - KΩ 500 - KHz 1.2 1.1 1.0 Pdet(V) 0.9 0.8 0.7 0.6 0.5 0.4 0.3 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Pout (dBm) Figure 3: SE2614BT Power Detector Characteristics Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014 7 DATA SHEET SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End Package Diagram 20 19 18 17 16 16 17 18 19 20 1 15 15 1 2 14 14 2 3 13 13 3 4 12 12 4 5 11 11 5 6 7 8 9 TOP VIEW 10 10 9 8 7 6 BOTTOM VIEW Figure 4: SE2614BT Package Outline Drawing Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014 8 DATA SHEET SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End Recommended Land and Solder Patterns 20 19 18 17 16 17 1 15 2 14 3 13 4 12 5 11 16 15 13 5 6 7 8 9 10 6 20 19 18 17 16 20 8 19 18 17 16 1 15 1 15 2 14 2 14 3 13 3 13 4 12 4 12 5 11 5 11 6 7 8 9 10 6 7 8 9 10 Figure 5: Recommended Land and Solder Patterns Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014 9 DATA SHEET SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End Package Handling Information Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SE2614BT is capable of withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For details on both attachment techniques, precautions, and handling procedures recommended, please refer to: “Quad Flat No-Lead Module Solder Reflow & Rework Information”, Document Number QAD-00045 “Handling, Packing, Shipping and Use of Moisture Sensitive QFN”, Document Number QAD-00044 Caution! ESD sensitive device Branding Information Pin 1 Designator Pin 1 Company Name Part Number Lot Code SiGe 2527L 614B Lot Code Figure 6: SE2614BT Branding Information Tape and Reel Information Parameter Devices Per Reel Reel Diameter Tape Width Value 3000 13 inches 12 millimeters Figure 7: SE2614BT-R Tape and Reel Information Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014 10 DATA SHEET SE2614BT: 2.4 GHz High Efficiency Wireless LAN Front-End Document Change History Revision Date Notes 1.0 January 17, 2011 Created 1.1 February 3, 2011 Updated MSL rating and landing pattern. 1.2 June 15, 2011 Updated ESD rating to 1KV 1.3 April 03, 2012 Updated with Skyworks logo and disclaimer statement 1.4 July 9, 2014 Removed PRELIMINARY from header. Updated disclaimer statement Copyright © 2012, 2014 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202394B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2014 11