DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Applications Product Description The SE2593A20 is a complete 802.11n WLAN RF front-end module providing all the functionality of the power amplifiers, LNA, power detector, T/R switch, diplexers and associated matching. The SE2593A20 provides a complete 2.4 GHz and 5 GHz WLAN Multiple Input, Multiple Output (MIMO) RF solution from the output of the transceiver to the antennas in a compact form factor. 802.11n, MIMO solutions IEEE802.11b DSSS WLAN IEEE802.11g OFDM WLAN IEEE802.11a OFDM WLAN Access Points, PCMCIA, PC cards Features 1 Transmit and 1 receive path architecture for use as MIMO building block. All RF ports matched to 50 Ω Integrated 2.4/5 GHz PA, 2.4/5 GHz LNA, TX Filter, T/R switches and diplexers Integrated Power Detector 19 dBm O/P Power, 802.11b, 11 Mbits, ACPR = 32 dBc 18 dBm @ 3.0 % EVM, 802.11g, 54 Mbits 16 dBm @ 3.0 % EVM, 802.11a, 54 Mbits Single supply voltage: 3.3 V ± 10 % Lead free, halogen free, RoHS compliant, MSL3 plated LGA package, 5 mm x 6 mm x 1.0 mm Ordering Information Part No. SE2593A20 SE2593A20-T * * Through Dec 2008 SE2593A20-R * * From Jan 2009 SE2593A20-EK1 Package Remark 30 pin LGA Samples 30 pin LGA Tray 30 pin LGA Tape and Reel N/A Evaluation kit The receive path is designed to maximize performance by providing both a low noise amplifier as well as a bypass state, for use when high power signals are being received. Designed for ease of use, all RF ports are matched to 50 Ω to simplify PCB layout and the interface to the transceiver RFIC. The SE2593A20 also includes a transmitter power detector for each band with 20 dB of dynamic range. The power ramp rise/fall time is less than 0.5 μs. The device also provides band pass filters for both the a and b/g bands prior to the input of each 2.4 GHz and 5 GHz power amplifiers, respectively. The SE2593A20 packaged in 5mm x 6mm x 1.0mm, Halogen free, Lead free, ROHS compliant, MSL 3 LGA package. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 1 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Functional Block Diagram Figure 1: Functional Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 2 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Pin Out Diagram Bsel V_LNA Figure 2: SE2593A20 Pin Out (Top View Through Package) Pin Out Description Pin No. Name 1 GND 2 Rg 3 GND 4 Ra 5 GND 6 Tg 7 GND 8 Ta Description Pin No. Name Description Ground 13 ENa 5 GHz PA Enable 2.4 GHz Receive Output 14 ENg 2.4 GHz PA Enable Ground 15 N/C Not used, floating PIN 5 GHz Receive Output 16 Det Power Detector Ground 17 N/C Not used, floating PIN 2.4 GHz Transmit Input 18 GND Ground Ground 19 N/C Not used, floating PIN 5 GHz Transmit Input 20 N/C Not used, floating PIN 9 GND Ground 21 GND Ground 10 N/C Not used, floating PIN 22 ANT Antenna 11 VCC Supply Voltage 23 GND Ground 12 GND Ground 24 RX Rx Switch Select Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 3 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Pin No. Name 25 TX Description Pin No. Name Tx Switch Select 28 N/C Description Not used, floating PIN 26 N/C Not used, floating PIN 29 V_LNA 27 GND Ground 30 Bsel LNA Enable LNA Band Select Absolute Maximum Ratings These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected workstations. Symbol Definition Min. Max. Unit VCC Supply Voltage -0.3 4.2 V PU ENg, ENa, V_LNA, Bsel -0.3 4.0 V - 10.0 dBm Operating Temperature Range -10 +85 °C Storage Temperature Range -40 +150 °C TXRF TA TSTG Ta, Tg, ANT terminated into 50Ω match Recommended Operating Conditions Symbol Parameter Min. Typ. Max. Unit VCC Supply Voltage 3.0 3.3 3.6 V TA Ambient Temperature -10 25 85 °C DC Electrical Characteristics Conditions: VCC = 3.3 V, TA = 25 C, as measured on Skyworks Solutions’ SE2593A20-EV1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted Symbol Parameter Conditions Min. Typ. Max. Unit TxICC-G Total 802.11g Transmit Supply Current POUT = 17 dBm, 54 Mbps OFDM signal, 64QAM, ENg = 3.3 V, ENa = 0 V, TX = 3.3 V, RX = 0 V - 140 165 mA TxICq-G Quiescent current , 802.11g Transmit supply Current No RF applied ENg = 3.3 V, ENa = 0 V, TX = 3.3V, RX = 0 V - - 110 mA TxICC-A Total 802.11a Transmit Supply Current POUT = 17 dBm, 54 Mbps OFDM signal, 64QAM, ENa = 3.3 V, ENg = 0 V, TX = 3.3 V, RX = 0 V - 180 200 mA TxICq-A Quiescent current , No RF applied - - 160 mA Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 4 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Symbol Parameter Conditions Min. Typ. Max. Unit 802.11a Transmit supply Current ENa = 3.3V, ENg = 0V, TX = 3.3V, RX = 0V RxICC-G Total 802.11b/g Receive Supply Current V_LNA = 3.3 V, Bsel = 3.3 V, RX = 3.3 V, TX = 0 V - 8.5 15 mA RxICC-a Total 802.11a Receive Supply Current V_LNA = 3.3 V, Bsel = 0 V, RX = 3.3 V, TX = 0 V - 8.5 15 mA ICC_OFF Total Supply Current No RF, ENg = ENa = 0 V, V_LNA = 0 V, TX = RX = 0 V - 2 10 μA Transmit Power Amplifier Logic Characteristics Conditions: VCC = 3.3 V, TA = 25 C, as measured on Skyworks Solutions’ SE2593A20-EV1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VENH Logic High Voltage for ENg, ENa (Module On) - 2.0 - VCC V VENL Logic Low Voltage ENg, ENa (Module Off) - 0 - 0.5 V IENH Input Current Logic High Voltage (ENg, ENa) - - 100 150 μA IENL Input Current Logic Low Voltage (ENg, ENa) - - 0.2 - μA Receive LNA Logic Characteristics Conditions: VCC = 3.3 V, TA = 25 C, as measured on Skyworks Solutions’ SE2593A20-EV1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VRENH Logic High Voltage for V_LNA, Bsel (Module On) - 2.5 - VCC V VRENL Logic Low for V_LNA, Bsel (Module Off) - -0.5 - 0.3 V IRENH Input Current Logic High Voltage (V_LNA, Bsel) - - 1 2 μA IRENL Input Current Logic Low Voltage (V_LNA, Bsel) - - 0 - μA LNA Enable Logic LNA Function Comment Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 5 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information V_LNA Bsel 2.4 GHz LNA 5 GHz LNA VRENL VRENL Bypass Mode Bypass Mode No gain in either path. This can be used for high input signal conditions. VRENL VRENH Bypass Mode Bypass Mode No gain in either path. This can be used for high input signal conditions. VRENH VRENL Off On Activates a-band LNA VRENH VRENH On Off Activates bg-band LNA RF Switch Characteristics Conditions: VCC = VEN = 3.3 V, TA = 25 C, as measured on Skyworks Solutions’ SE2593A20-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VCTL_ON Control Voltage (On State) - 3.0 - 3.6 V VCTL_OFF Control Voltage (OFF State) - 0.0 - 0.2 V SWON Low Loss Switch Control Voltage High State = VCTL_ON - VCTL_OFF 2.8 - VCC V SWOFF High Loss Switch Control Voltage Low State = VCTL_OFF - VCTL_OFF 0 - 0.3 V ICTL_ON Switch Control Bias Current (RF Applied) On pin (TX, RX) being driven high. RF Applied - - 100 A ICTL_ON Switch Control Bias Current (No RF) On pin (TX, RX) being driven high. No RF - - 30 A - - 100 pF CCTL Control Input Capacitance - RF Switch Logic RF Switch Function CTRL_T CTRL_R Tg, Ta – ANT Rg, Ra – ANT SWON SWOFF ON OFF SWOFF SWON OFF ON Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 6 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information 2.4 GHz AC Electrical Characteristics 2.4 GHz Transmit Characteristics Conditions: VCC = 3.3 V, ENg = TX = 3.3 V, V_LNA = ENa = RX = 0 V, TA = 25 C, as measured on Skyworks Solutions’ SE2593A20-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FIN Parameter Frequency Range Condition Min. Typ. Max. Unit - 2400 - 2500 MHz Output power 54 Mbps OFDM signal, 64QAM, EVM ≤ 3.0 % 17 18 - dBm P802.11b Output power 11 Mbps CCK signal, BT = 0.45 ACPR(Adj) < -32 ACPR(Alt) < -52 19 20 - dBm BEVM Backed Off EVM 54 Mbps, OFDM signal, 64 QAM, P = 12 dBm - 1.5 - % - 25 - dBm 23 - - 30 0 0 2 dB dB P802.11g P1dB S21 ∆S21 2f,3f NF P1dB - Small Signal Gain 2400 – 2485 MHz 960 – 1600 MHz 1600 – 1660 MHz 3260 – 3267 MHz Small Signal Gain Variation Over Band Over any 40 MHz band - - 0.5 Pout = 18 dBm, 1 Mbps, 802.11b CCK - -50 -45.2 -55 -48.2 Harmonics dBm Pout = 17 dBm, 54Mbps OFDM signal Noise Figure Pout < 20 dBm - - 10 dB Rise Time 10 % to 90% of final output power level - - 0.5 μs tdr, tdf Delay and rise/fall Time 50 % of VEN edge and 90/10 % of final output power level - - 0.5 μs S11 Input Return Loss - 10 - - dB - - -45 dBm/MHz tr Spur Spurious Pout < 20 dBm, VSWR = 2:1 100 MHz to 10 GHz STAB Stability POUT ≤ PSAT Load VSWR = 10:1 All non-harmonically related outputs less than -50 dBc/1MHz Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 7 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information 2.4 GHz Receive Characteristics Conditions: VCC = V_LNA = Bsel = RX = 3.3V, ENg = ENa = TX = 0 V, TA = 25 C, as measured on Skyworks Solutions’ SE2593A20-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FOUT S21 ∆S21 Parameter Condition Min. Typ. - 2400 - 2500 MHz Receive Gain, LNA enabled. 2400 – 2485 MHz 800 – 1200 MHz 1200 – 1700 MHz 1700 – 1900 MHz 3200 – 6000 MHz 11 - 13 - -10 3 +10 +10 dB Receive Gain, Bypass mode V_LNA = 0 V 2400 – 2485 MHz - -7 - Gain Variation 2400 – 2485 MHz, Over any 40MHz band - - .5 dB Frequency Range Max. Unit dB NF Noise Figure - 2.6 7 2.8 - dB IIP3 Third Order Intercept - TBD - dBm - -23 - dB -10 - - dBm 10 12 - dB - -5 8 -3.5 - dBm 500 nsec ISOLRRX Reverse Isolation V_LNA = 0V, RX = 0 V INT Interferer With this input , IIP3 can only degrade by 1dB S11 Input Return Loss IP1dB TEN - Input P1dB V_LNA = 3.3 V V_LNA = 0 V Enable Time 10% to 90% of RX RF power, from time that V_LNA is at 50% 5 GHz AC Electrical Characteristics 5 GHz Transmit Characteristics Conditions: VCC = 3.3 V, ENa = TX = 3.3 V, V_LNA = ENg = RX = 0 V, TA = 25 C, as measured on Skyworks Solutions’ SE2593A20-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FIN Parameter Frequency Range Condition Min. Typ. Max. Unit - 4900 - 5850 MHz P802.11a Nominal Output Power 54 Mbps OFDM signal, 64 QAM, EVM = 3.0 % - 16 - dBm BEVM Backed Off EVM 54 Mbps, OFDM signal, 64 QAM, P = 7 dBm - 1.5 - % P1DB - - 22 - dBm P1dB Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 8 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Symbol S21 ∆S21 Parameter Min. Typ. Max. 22 - -30 -10 -10 -12 -10 28 10 5 3 -10 10 dB Small Signal Gain Variation Over 40 MHz Channel - - 0.4 dB Small Signal Gain Variation Over Band - - 3 dB - -45 -50 -42 -48 dBm/MHz Small Signal Gain Condition 4900 – 5850 MHz 960 – 3265 MHz 3265 – 3900 MHz 6900 – 7250 MHz 7250 – 7800 MHz 7800 – 8500 MHz Unit Harmonics, 54Mbps, 802.11a signal Pout = 16dBm 4900 – 5150 MHz 5150 – 5850 MHz Noise Figure Pout < 16 dBm 4900 – 5850 MHz - TBD 10 dB Rise Time 10 % to 90% of final output power level - - 0.8 μs tdr, tdf Delay and rise/fall Time 50 % of VEN edge and 90/10 % of final output power level - - 0.5 μs S11 Input Return Loss 10 - - dB - - -45 dBm/MHz 2f,3f NF tr - SPUR Spurious Pout < 16dBm, VSWR = 2:1, 100 – 24000 MHz STAB Stability POUT ≤ 18 dBm Load VSWR = 10:1 All non-harmonically related outputs less than -50 dBc/1MHz 5 GHz Receive Characteristics Conditions: VCC = V_LNA = RX = 3.3 V, Bsel = ENg = ENa = TX = 0 V, TA = 25 C, as measured on Skyworks Solutions’ SE2593A20-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FOUT Parameter Condition Min. Typ. - 4900 - 5850 MHz Receive Gain 4900 – 5850 MHz 800 – 2500 MHz 2500 – 3900 MHz 6500 – 7800 MHz - 12 -10 6 11 -5 10 12 dB Receive Gain, Bypass mode V_LNA = 0.0 V - -7 - dB Gain Variation 4900 – 5850 MHz, Over any 40MHz band - - 0.5 dB Frequency Range S21 ∆S21 Max. Unit NF Noise Figure - 2.8 3.2 dB IIP3 Third Order Intercept - TBD - dBm Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 9 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Symbol ISOLRRX Parameter Condition Min. Typ. Max. Unit Reverse Isolation V_LNA = 0V, RX = 0V - 20 - dB INT Interferer With this input IIP3 can only degrade by 1dB -10 - - dBm S11 Return Loss 8 12 - dB IP1dB Input P1dB V_LNA = 3.3 V V_LNA = 0 V - -3 10 - dBm Enable Time 10% to 90% of RX RF power, from time that V_LNA is at 50% 500 nsec TEN - 2.4 GHz Power Detector Characteristics Conditions: VCC = 3.3 V, ENg = TX = 3.3 V, LNAa = LNAg = RX = ENa = 0 V, TA = 25 C, as measured on Skyworks Solutions’ SE2593A20-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Condition Min. Typ. Max. Unit - 2400 - 2500 MHz 0 - 22 dBm FOUT Frequency Range PDR Power detect range, peak power PDZLOAD DC load impedance - - 2.7 3 kΩ PDVP17 Output Voltage, POUT = 21 dBm - - - 1.0 V PDVp0 Output Voltage, POUT = 5 dBm - 0.35 - V PDVpnoRF Output Voltage, POUT = No RF - - 0.32 - V LPF-3dB Power detect low pass filter -3dB corner frequency 270 300 400 KHz Measured at ANT Load = high impedance Typ: 500 kΩ Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 10 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Power Detector Positive Slope Detector Voltage (V) Pdet2400 Pdet2450 Pdet2500 1.2 1.1 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 4 6 8 10 12 14 16 18 20 22 Pout (dBm) Figure 3: Power Detector Characteristics 5 GHz Power Detector Characteristic Conditions: VCC = 3.3 V, ENa = TX = 3.3 V”, LNAa = LNAg = RX = ENg = 0 V, TA = 25 C, as measured on Skyworks Solutions’ SE2593A20-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Condition Min. Typ. Max. Unit - 4900 - 5850 MHz 0 - 20 dBm FOUT Frequency Range PDR Power detect range, peak power PDZLOAD DC load impedance - - 2.7 3 kΩ PDVP17 Output Voltage, POUT = 17 dBm - - - 1.0 V PDVp0 Output Voltage, POUT = 3 dBm - - 0.35 - V PDVpnoRF Output Voltage, POUT = No RF - - 0.32 - V LPF-3dB Power detect low pass filter -3dB corner frequency 270 300 400 KHz Measured at ANT Load = high impedance Typ: 500 kΩ Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 11 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Power Detector Positive Slope Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 12 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Package Diagram 00 Bsel V_LNA N/C GND N/C Vcrtl2 30 29 28 27 26 25 25 26 27 28 29 30 GND 1 24 Vctrl1 24 2Rx 2 23 GND 23 GND 3 22 ANT 22 5Rx 4 21 GND 21 GND 5 20 N/C 20 5 2Tx 6 19 N/C 19 6 GND 7 18 GND 18 5Tx 8 17 N/C 17 GND SLUG 2 3 4 GND SLUG 7 8 GND SLUG GND 1 GND SLUG 9 16 10 11 12 13 14 15 N/C Vcc GND ven5 ven2 N/C Vpdet 16 15 14 13 12 11 10 9 TOP SIDE BOTTOM SIDE PIN DESCRIPTION TABLE PIN NAME DESCRIPTION PIN NAME GROUND SLUG DETAIL DESCRIPTION SIGNAL PAD DETAIL CL CL CL CL Figure 4: Package Outline Drawing Recommended Land and Solder Patterns Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 13 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information 30 29 28 27 26 25 30 29 28 27 26 25 30 29 28 27 26 25 1 24 1 24 1 24 2 23 2 23 2 23 3 22 3 22 3 22 4 21 4 21 4 21 5 20 5 20 5 20 6 19 6 19 6 19 7 18 7 18 7 18 8 17 8 17 8 17 9 16 9 16 9 10 11 12 13 14 10 15 11 12 13 14 15 16 10 11 12 13 14 15 PCB METAL & VIA HOLE PCB SOLDER MASK PCB SOLDER STENCIL TOP (X-Ray) VIEW TOP (X-Ray) VIEW TOP (X-Ray) VIEW PERIPHERAL PAD PATTERN DETAIL GENERAL NOTES: RECOMMENDED FOOTPRINT NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS. 2. DIMENSIONING AND TOLERANCES CONFORM TO ASME Y14.5M-1994. (UNLESS OTHERWISE SPECIFIED THE FOLLOWING VALUES APPLY) 4. VIA HOLE INFORMATION: 4a. RECOMMENDED VIA HOLE SIZE (Ø): 0.150 - 0.300mm 4b. RECOMMENDED VIA HOLE PITCH: AS SHOWN 4c. RECOMMENDED VIA WALL Cu PLATING: 30-35um 4d. RECOMMENDED THAT VIAS BE TENTED WITH SOLDERMASK ON PCB BACKSIDE AND FILLED WITH SOLDER. 4e. VIA IN SIGNAL PAD DETAIL, TYP 10 PLCS. 4f. TOTAL VIA COUNT AS SHOWN: 30. 5. SOLDER MASK GEOMETRY FEATURES: 5a. ALL PERIPHERAL PCB PADS ARE NON-SOLDER MASK DEFINED. 5b. ALL GROUND PADDLE FEATURES ARE SOLDER MASK DEFINED. 6. SOLDER STENCIL APERTURE FEATURES: 6a. SOLDER STENCIL APERATURE OPENINGS ARE SMALLER THEN PERIPHERAL PCB METAL PADS. 6b. RECOMMENDED SOLDER STENCIL APERTURE ARRAY TO TARGET APPROXIMATELY 50 - 80% COVERAGE OF SOLDER MASK OPENINGS, EXCEPT AS NOTED. 7. RECOMMENDED SOLDER STENCIL THICKNESS: 5.0mils (0.127mm). 8. PCB ACAD AND GERBER FILES AVAILABLE UPON REQUEST. DECIMAL TOLERANCE: ANGULAR TOLERANCE: X.X (1 PLC) ± 0.1mm ± 1° X.XX (2 PLC) ± 0.05mm X.XXX (3 PLC) ± 0.025mm CL CL 3. UNLESS SPECIFIED DIMENSIONS ARE SYMMETRICAL ABOUT CENTER LINES. Figure 5: Recommended Land and Solder Patterns Package Handling Information Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SE2593A20 is capable of withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For details on both attachment techniques, precautions, and handling procedures recommended, please refer to: “Land Grid Array Module Solder Reflow & Rework Information”, Document Number QAD-00046. “Handling, Packing, Shipping and Use of Moisture Sensitive LGA”, Document Number QAD-00047. Caution! Class 0 ESD sensitive Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 14 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Branding Information Pin 1 Identifier Terminal Finish Pin 1 e4 Part Number SiGe 2593A20 Lot Code Lot Code Figure 6: SE2593A20 Branding Information Tray Information – Available until Dec 2008 Tray Matrix (Devices) Devices per Tray Trays per stack Devices per stack 14 x 35 490 10 + 1(empty) 4,900 Figure 6: Tray Mechanical Drawing Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 15 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Figure 7: Tray Pocket Mechanical Drawing Tape and Reel Information - Available from Jan 2009 Parameter Value Devices per Reel 3,000 Reel Diameter 13 Inches Tape Width 12 millimetres Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 16 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Figure 7: Tape Mechanical Drawing Document Change History Revision Date Notes 1.0 November 9, 2006 Create 1.1 February 8, 2007 Standardize Pin Naming. 1.2 March 28, 2007 Update 5GHz detector characteristics 1.3 March 28, 2007 Updated package thickness 1.4 June 29, 2007 Modify LNA controls from LNAg & LNAa to BSEL & V_LNA. Updated current consumption in 2GHz and 5GHz TX channels Updated spurious rejection specifications in 2GHz and 5GHz TX channels Updated noise figure specification in 2GHz and 5GHz RX channels. Updated gain profiles in 2GHz and 5GHz RX chains Updated 5GHz detector characteristics 1.5 August 23, 2007 Updated schematic 1.6 January 28, 2008 Updated product name from SE2593A to SE2593A20. Updated quiescent current in 2GHz and 5GHz TX chains. Added shipping tray information 1.7 March 5, 2008 Updated harmonics specification in 2GHz TX chain. 1.8 April 15, 2008 Add 5GHz detector plot Update tray specification and MOQ 1.9 Jun 15, 2008 Updated packaging for halogen free Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 17 DATA SHEET SE2593A20: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Revision Date Notes Updated to include recommended land patterns, solder patterns. 2.0 Sep 24, 2008 Updated for 3.2GHz LO gain in the 2GHz channel Added Tape and Reel Packing information and discontinued Tray Packing. 2.1 May 26, 2009 Amended back page. 2.2 Mar 28, 2012 Updated with Skyworks logo and disclaimer statement Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202431A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 18