DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Applications Product Description The SE2595L is a complete 802.11n WLAN RF frontend module providing all the functionality of the power amplifiers, LNA, power detector, T/R switch, diplexers and associated matching. The SE2595L provides a complete 2.4 GHz and 5 GHz WLAN Multiple Input, Multiple Output (MIMO) RF solution from the output of the transceiver to the antennas in a compact form factor. 802.11n, MIMO solutions IEEE802.11b DSSS WLAN IEEE802.11g OFDM WLAN IEEE802.11a OFDM WLAN Access Points, PCMCIA, PC cards Features 1 Transmit and 1 receive path architecture for use as MIMO building block. All RF ports matched to 50 Ω Integrated 2.4/5 GHz PA, 2.4/5 GHz LNA, TX Filter, T/R switches and diplexers Integrated Power Detector 19 dBm O/P Power, 802.11b, 11 Mbits, ACPR = 32 dBc 18 dBm @ 3.0 % EVM, 802.11g, 54 Mbits 16 dBm @ 3.0 % EVM, 802.11a, 54 Mbits Single supply voltage: 3.3 V ± 10 % Lead free, Halogen Free and RoHS compliant Thin lead free plated package, 4 mm x 6 mm x 0.9 mm, MSL 1 The receive path is designed to maximize performance by providing both a low noise amplifier as well as a bypass state, for use when high power signals are being received. Designed for ease of use, all RF ports are matched to 50 Ω to simplify PCB layout and the interface to the transceiver RFIC. The SE2595L also includes a transmitter power detector for each band with 20 dB of dynamic range. The power ramp rise/fall time is less than 0.5 μs. The device also provides band pass filters for both the a and b/g bands prior to the input of each 2.4 GHz and 5 GHz power amplifiers, respectively. Ordering Information Part No. Package Remark SE2595L SE2595L-R SE2595L-EK1 32 pin QFN 32 pin QFN N/A Samples Tape & Reel Evaluation kit Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 1 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Functional Block Diagram Figure 1: Functional Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 2 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Pin Out Diagram Figure 2: SE2595L Pin Out (Top View Through Package) Pin Out Description Pin No. Name 1 Ra 2 VCC 3 GND 4 Tg 5 Ta 6 7 Description Pin No. Name Description 5 GHz Receive Output 14 GND Ground Supply Voltage, LNA 15 GND Ground Ground 16 GND Ground 2.4 GHz Transmit Input 17 GND Ground 5 GHz Transmit Input 18 GND Ground GND Ground 19 GND Ground GND Ground 20 GND Ground 8 GND Ground 21 ANT Antenna 9 Det Power Detector, 2.5 & 5 GHz 22 GND Ground 10 ENa 5 GHz PA Enable 23 RX Rx Switch Select 11 ENg 2.4 GHz PA Enable 24 TX Tx Switch Select 12 VCC1 Supply Voltage, Driver Stage 25 NU Not Used 13 VCC2 Supply Voltage, Power Stage 26 NU Not Used Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 3 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Pin No. Name 27 GND 28 29 Description Pin No. Name Ground 30 V_LNA GND Ground 31 Bsel GND Ground 32 Rg Description LNA Enable LNA Band Select 2.4 GHz Receive Output Absolute Maximum Ratings These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected workstations. Symbol Definition Min. Max. Unit VCC Supply Voltage -0.3 4.2 V PU ENg, ENa, V_LNA, Bsel -0.3 4.0 V - 10.0 dBm Operating Temperature Range -40 85 °C TSTG Storage Temperature Range -40 150 °C ESD HBM JEDEC JESD22-A114 all pins 150 - V TXRF TA Ta, Tg, ANT terminated into 50Ω match Recommended Operating Conditions Symbol Parameter Min. Typ. Max. Unit VCC Supply Voltage 3.0 3.3 3.6 V TA Ambient Temperature -40 25 85 °C DC Electrical Characteristics Conditions: VCC = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2595L-EV1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted Symbol Parameter Conditions Min. Typ. Max. Unit TxICC-G Total 802.11g Transmit Supply Current POUT = 17 dBm, 54 Mbps OFDM signal, 64QAM, ENg = 3.3 V, ENa = 0 V, TX = 3.3 V, RX = 0 V - 180 - mA TxICq-G Quiescent current , 802.11g Transmit supply Current No RF applied ENg = 3.3 V, ENa = 0 V, TX = 3.3V, RX = 0 V - 110 - mA TxICC-A Total 802.11a Transmit Supply Current POUT = 17 dBm, 54 Mbps OFDM signal, 64QAM, ENa = 3.3 V, ENg = 0 V, TX = 3.3 V, RX = 0 V - 230 - mA Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 4 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Symbol Parameter Conditions Min. Typ. Max. Unit TxICq-A Quiescent current , 802.11a Transmit supply Current No RF applied ENa = 3.3V, ENg = 0V, TX = 3.3V, RX = 0V - 155 - mA RxICC-G Total 802.11b/g Receive Supply Current V_LNA = 3.3 V, Bsel = 3.3 V, RX = 3.3 V, TX = 0 V - 8.5 15 mA RxICC-a Total 802.11a Receive Supply Current V_LNA = 3.3 V, Bsel = 0 V, RX = 3.3 V, TX = 0 V - 8.5 15 mA ICC_OFF Total Supply Current No RF, ENg = ENa = 0 V, V_LNA = 0 V, TX = RX = 0 V - 2 100 μA Transmit Power Amplifier Logic Characteristics Conditions: VCC = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2595L-EV1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VENH Logic High Voltage for ENg, ENa (Module On) - - 2.0 VCC V VENL Logic Low Voltage ENg, ENa (Module Off) - 0 0.5 - V IENH Input Current Logic High Voltage (ENg, ENa) - - 100 150 μA IENL Input Current Logic Low Voltage (ENg, ENa) - - 0.2 - μA Receive LNA Logic Characteristics Conditions: VCC = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2595L-EV1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VRENH Logic High Voltage for V_LNA, Bsel (Module On) - - 3.2 VCC V VRENL Logic Low for V_LNA, Bsel (Module Off) - -0.5 0.3 - V IRENH Input Current Logic High Voltage (V_LNA, Bsel) - - - 400 μA IRENL Input Current Logic Low Voltage (V_LNA, Bsel) - - 0 - μA Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 5 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information LNA Enable Logic LNA Function Comment V_LNA Bsel 2.4 GHz LNA 5 GHz LNA VRENL VRENL Bypass Mode Bypass Mode No gain in either path. This can be used for high input signal conditions. VRENL VRENH Bypass Mode Bypass Mode No gain in either path. This can be used for high input signal conditions. VRENH VRENL Off On Activates a-band LNA VRENH VRENH On Off Activates bg-band LNA RF Switch Characteristics Conditions: VCC = VEN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2595L-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VCTL_ON Control Voltage (On State) - 3.0 - 3.6 V VCTL_OFF Control Voltage (OFF State) - 0.0 - 0.2 V SW ON Low Loss Switch Control Voltage High State = VCTL_ON - VCTL_OFF 2.8 - VCC V SW OFF High Loss Switch Control Voltage Low State = VCTL_OFF - VCTL_OFF 0 - 0.2 V ICTL_ON Switch Control Bias Current (RF Applied) On pin (TX, RX) being driven high. RF Applied - - 100 µA ICTL_ON Switch Control Bias Current (No RF) On pin (TX, RX) being driven high. No RF - - 30 µA - - 100 pF CCTL Control Input Capacitance - RF Switch Logic RF Switch Function CTRL_T CTRL_R Tg, Ta – ANT Rg, Ra – ANT SW ON SW OFF ON OFF SW OFF SW ON OFF ON Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 6 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information 2.4 GHz AC Electrical Characteristics 2.4 GHz Transmit Characteristics Conditions: VCC = 3.3 V, ENg = TX = 3.3 V, V_LNA = ENa = RX = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2595L-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FIN Parameter Frequency Range Condition Min. Typ. Max. Unit - 2400 - 2485 MHz P802.11g Output power 54 Mbps OFDM signal, 64QAM, EVM ≤ 3.0 % 17 18 - dBm P802.11b Output power 11 Mbps CCK signal, BT = 0.45 ACPR(Adj) < -32 ACPR(Alt) < -52 19 20 - dBm BEVM Backed Off EVM 54 Mbps, OFDM signal, 64 QAM, P ≤ 12 dBm - 1.5 - % - 23 - dBm 23 - - 30 0 0 2 dB dB P1dB P1dB S21 Small Signal Gain 2400 – 2485 MHz 960 – 1600 MHz 1600 – 1660 MHz 3260 – 3267 MHz Small Signal Gain Variation Over Band Over any 40 MHz band - - 0.5 Pout = 18 dBm, 1 Mbps, BPSK - -50 -45.2 -55 -48.2 ΔS21 2f,3f - Harmonics dBm Pout = 17 dBm, 54Mbps OFDM signal NF Noise Figure Pout < 20 dBm - - 10 dB Rise Time 10 % to 90% of final output power level - - 0.5 μs tdr, tdf Delay and rise/fall Time 50 % of VEN edge and 90/10 % of final output power level - - 0.5 μs S11 Input Return Loss - - 10 - dB - - -45 dBm/MHz tr Spur Spurious Pout < 20 dBm, VSWR = 2:1 100 MHz to 10 GHz STAB Stability POUT ≤ 20dBm Load VSWR = 10:1 All non-harmonically related outputs less than -50 dBc/1MHz Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 7 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information 2.4 GHz Receive Characteristics Conditions: VCC = V_LNA = Bsel = RX = 3.3V, ENg = ENa = TX = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2595L-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FOUT Parameter Condition Min. Typ. - 2400 - 2500 MHz Receive Gain, LNA enabled. 2400 – 2485 MHz 800 – 1200 MHz 1200 – 1700 MHz 1700 – 1900 MHz 3200 – 6000 MHz 11 - 13 10 -10 3 10 - dB Receive Gain, Bypass mode V_LNA = 0 V 2400 – 2485 MHz - -7 - Gain Variation 2400 – 2485 MHz, Over any 40MHz band - - .5 dB - 2.6 7 2.8 - dB Frequency Range S21 ΔS21 Max. Unit dB NF Noise Figure IIP3 Third Order Intercept 2.45GHz, 1MHz offset - 9 - dBm Reverse Isolation V_LNA = 0V, RX = 0 V - -23 - dB INT Interferer With this input , IIP3 can only degrade by 1dB -10 - - dBm S11 Input Return Loss 10 12 - dB ISOLRRX IP1dB TEN - Input P1dB V_LNA = 3.3 V V_LNA = 0 V - -3.5 8 - dBm Enable Time 10% to 90% of RX RF power, from time that V_LNA is at 50% - - 500 nsec Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 8 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information 5 GHz AC Electrical Characteristics 5 GHz Transmit Characteristics Conditions: VCC = 3.3 V, ENa = TX = 3.3 V, V_LNA = ENg = RX = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2595L-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FIN Parameter Condition Min. Typ. - 4900 - 5850 MHz Frequency Range Max. Unit P802.11a Nominal Output Power 54 Mbps OFDM signal, 64 QAM, EVM = 3.0 % - 16 - dBm BEVM Backed Off EVM 54 Mbps, OFDM signal, 64 QAM, P ≤ 7 dBm - 1.5 - % P1DB - - 21 - dBm Small Signal Gain 4900 960 3265 6900 7250 7800 22 - -30 -10 -10 -12 -10 31 10 8 6 -10 10 dB Small Signal Gain Variation Over 40 MHz Channel - 0.4 - dB Small Signal Gain Variation Over Band - 6 - dB - -45 -50 -42 -48 dBm/MHz P1dB S21 ΔS21 – – – – – – 5850 3265 3900 7250 7800 8500 MHz MHz MHz MHz MHz MHz Harmonics, 54Mbps, 802.11a signal Pout = 16dBm 4900 – 5150 MHz 5150 – 5850 MHz Noise Figure Pout < 16 dBm 4900 – 5850 MHz - - 10 dB Rise Time 10 % to 90% of final output power level - - 0.8 μs tdr, tdf Delay and rise/fall Time 50 % of VEN edge and 90/10 % of final output power level - - 0.5 μs S11 Input Return Loss - 8 - dB - - -45 dBm/MHz 2f,3f NF tr - SPUR Spurious Pout < 16dBm, VSWR = 2:1, 100 – 24000 MHz STAB Stability POUT ≤ 17 dBm Load VSWR = 10:1 All non-harmonically related outputs less than -50 dBc/1MHz Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 9 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information 5 GHz Receive Characteristics Conditions: VCC = V_LNA = RX = 3.3 V, Bsel = ENg = ENa = TX = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2595L-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FOUT Parameter Condition Min. Typ. - 4900 - 5850 MHz Receive Gain 4900 – 5850 MHz 800 – 2500 MHz 2500 – 3900 MHz 6500 – 7800 MHz - 12 -10 6 11 -5 - dB Receive Gain, Bypass mode V_LNA = 0.0 V - -7 - dB Gain Variation 4900 – 5850 MHz, Over any 40MHz band - - 0.5 dB - 2.8 3.2 dB Frequency Range S21 ΔS21 Max. Unit NF Noise Figure IIP3 Third Order Intercept 5.45GHz, 1MHz offset - -3 - dBm Reverse Isolation V_LNA = 0V, RX = 0V - 20 - dB INT Interferer With this input IIP3 can only degrade by 1dB -10 - - dBm S11 Return Loss - 8 - dB IP1dB Input P1dB V_LNA = 3.3 V V_LNA = 0 V - -3 10 - dBm Enable Time 10% to 90% of RX RF power, from time that V_LNA is at 50% - - 500 nsec ISOLRRX TEN - 2.4 GHz Power Detector Characteristics Conditions: VCC = 3.3 V, ENg = TX = 3.3 V, V_LNA = RX = ENa = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2595L-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Condition Min. Typ. Max. Unit - 2400 - 2500 MHz 0 - 22 dBm FOUT Frequency Range PDR Power detect range, peak power PDZLOAD DC load impedance - - 2.7 3 kΩ PDVP22 Output Voltage, POUT = 21 dBm - - 0.86 - V PDVp0 Output Voltage, POUT = 5 dBm - - 0.35 - V Measured at ANT Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 10 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Symbol Parameter Condition Min. Typ. PDVpnoRF Output Voltage, POUT = No RF - - 0.32 - V LPF-3dB (Note 2) Power detect low pass filter -3dB corner frequency 270 300 400 KHz Load = high impedance Typ: 500 kΩ Max. Unit Figure 3: Power Detector Characteristics Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 11 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information 5 GHz Power Detector Characteristic Conditions: VCC = 3.3 V, ENa = TX = 3.3 V, V_LNA = RX = ENg = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2595L-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Condition Min. Typ. Max. Unit - 4900 - 5850 MHz 0 - 20 dBm FOUT Frequency Range PDR Power detect range, peak power PDZLOAD DC load impedance - - 2.7 3 kΩ PDVP20 Output Voltage, POUT = 17 dBm - - 0.80 - V PDVp0 Output Voltage, POUT = 3 dBm - - 0.34 - V PDVpnoRF Output Voltage, POUT = No RF - - 0.32 - V LPF-3dB (Note 3) Power detect low pass filter -3dB corner frequency 270 300 400 KHz Measured at ANT Load = high impedance Typ: 500 kΩ Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 12 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 13 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Package Diagram 32 32 30 29 28 27 26 25 24 23 23 24 25 26 27 28 29 30 32 32 1 22 22 1 2 21 21 2 3 20 20 3 4 19 19 4 5 18 18 5 6 17 17 6 7 8 9 10 11 12 13 14 15 16 16 15 14 13 12 11 10 9 8 7 TOP VIEW BOTTOM VIEW Figure 4: Package Outline Drawing Recommended Land and Solder Patterns Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 14 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information QFN PACKAGE OUTLINE 32 32 30 29 28 26 27 25 24 23 32 32 30 29 28 27 26 25 24 23 32 32 30 29 28 27 26 25 24 23 1 22 1 22 1 22 2 21 2 21 2 21 3 20 3 20 3 20 4 19 4 19 4 19 5 18 5 18 5 18 6 17 6 17 6 17 7 8 9 10 11 13 12 14 15 16 7 8 9 10 11 12 13 14 15 16 7 8 9 10 11 12 13 14 15 16 PCB METAL & VIA HOLE PCB SOLDER MASK PCB SOLDER STENCIL TOP (X-Ray) VIEW TOP (X-Ray) VIEW TOP (X-Ray) VIEW PERIPHERAL PAD PATTERN DETAIL GENERAL NOTES: A. ALL DIMENSIONS ARE IN MILLIMETERS. B. DIMENSIONING AND TOLERANCES CONFORM TO ASME Y14.5M-1994. (UNLESS OTHERWISE SPECIFIED THE FOLLOWING VALUES APPLY) CL DECIMAL TOLERANCE: X.X (1 PLC) ± 0.1mm X.XX (2 PLC) ± 0.05mm X.XXX (3 PLC) ± 0.025mm CL ANGULAR TOLERANCE: ± 1° C. UNLESS SPECIFIED DIMENSIONS ARE SYMMETRICAL ABOUT CENTER LINES. RECOMMENDED FOOTPRINT NOTES: 1. VIA HOLE INFORMATION: 1a. RECOMMENDED VIA HOLE SIZE (Ø): 0.150 - 0.300mm 1b. RECOMMENDED VIA HOLE PITCH: AS SHOWN 1c. RECOMMENDED VIA WALL Cu PLATING: 30-35um 1d. RECOMMENDED THAT VIAS BE TENTED WITH SOLDERMASK ON PCB BACKSIDE AND FILLED WITH SOLDER. 1e. TOTAL VIA COUNT AS SHOWN: 28. 2. SOLDER MASK GEOMETRY FEATURES: 2a. ALL PERIPHERAL PCB PADS ARE NON-SOLDER MASK DEFINED. 2b. ALL GROUND PADDLE FEATURES ARE SOLDER MASK DEFINED. 3. SOLDER STENCIL APERTURE FEATURES: 3a. SOLDER STENCIL APERATURE OPENINGS ARE SMALLER THEN PERIPHERAL PCB METAL PADS. 3b. RECOMMENDED SOLDER STENCIL APERTURE ARRAY TO TARGET APPROXIMATELY 50 - 80% COVERAGE OF SOLDER MASK OPENINGS, EXCEPT AS NOTED. 4. RECOMMENDED SOLDER STENCIL THICKNESS: 5.0mils (0.127mm). 5. PCB ACAD AND GERBER FILES AVAILABLE UPON REQUEST. Figure 5: Recommended Land and Solder Pattern Package Handling Information Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SE2595L is capable of withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For details on both attachment techniques, precautions, and handling procedures recommended, please refer to: “Quad Flat No-Lead Module Solder Reflow & Rework Information”, Document Number QAD-00045 “Handling, Packing, Shipping and Use of Moisture Sensitive QFN”, Document Number QAD-00044 “ESD Control Policy”, Document Number SQ03-0062 Caution! Class 0 ESD sensitive device Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 15 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Tape and Reel Information Parameter Devices Per Reel Reel Diameter Tape Width Value 3000 13 inches 16 millimeters Figure 6: Tape and Reel Information Branding Information Pin 1 Identifier Terminal Finish Pin 1 e3 Part Number Lot Code SiGe SE2595L Lot Code Figure 7: SE2595L Branding Information Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 16 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Document Change History Revision 1.0 Date Notes June 29, 2008 Create 1.1 March 11, 2009 Update Gain in both bands Updated detector characteristics Updated packing method to Tape & Reel Added package outline drawing and recommended land pattern Updated input return loss. Updated RX IIP3 1.2 April 6, 2009 Updated LNA characteristics. Corrected product and terminal finish marking on Branding information 1.3 April 29, 2009 Updated LNA Logic Characteristics (IRENH) to 400uA 1.4 May 1, 2009 Updated detector characteristics 1.5 July 30, 2009 Updated 5GHz Gain Characteristics 1.6 Aug 28, 2009 Updated Tape and Reel drawings. 1.7 Jan 11, 2010 Updated ICC_OFF specification. 1.8 Jan 8, 2011 Updated MSL rating to MSL 1 1.9 Apr 9, 2011 Updated recommended operating conditions to industrial temperature range 2.0 Mar 28, 2012 Updated with Skyworks logo and disclaimer statement Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 17 DATA SHEET SE2595L: Dual-Band 802.11n Wireless LAN Front-End Preliminary Information Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202433A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 18