DATA SHEET SKY65362-11: 900 to 930 MHz High-Power RF Front-End Module Applications Description Smart meters The SKY65362-11 is a high-performance, highly integrated RF front-end module (FEM) designed for high-power Industrial, Scientific, Medical (ISM) band applications operating in the 900 to 930 MHz frequency range. In-home appliances Smart thermostats The FEM is designed for ease of use and maximum flexibility with fully matched, 50 Ω power amplifier (PA) input and output, and digital controls compatible with 1.6 to 3.3 V CMOS levels. Features Integrated PA with +30.5 dBm output power The RF blocks operate over a wide supply voltage range from 3.00 to 5.25 V that allows the SKY65362-11 to be used in battery powered applications over a wide spectrum of the battery discharge curve. Integrated LNA with programmable bypass Low FEM NF of 2.5 dB, typical Single-ended 50 Ω transmit/receive RF interface The SKY65362-11 is packaged in a 36-pin, 6 x 6 mm Multi-Chip Module (MCM), which allows for a highly manufacturable low-cost solution. Supply voltage: 3.00 V to 5.25 V Sleep mode current: <1 μA Small MCM (36-pin, 6 x 6 mm) package (MSL3, 260 C per JEDEC J-STD-020) A functional block diagram of the SKY65362-11 is shown in Figure 1. The 36-pin MCM package and pinout are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. CPS ANT_SEL PDETF PDETR IALARM CTX CSD Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. Logic control TX ANT1 2-Stage GaAs PA ANT2 Switch RX RX_FLT LNA_IN 1-Stage LNA Y0205 Figure 1. SKY65362-11 FEM Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202886B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 9, 2015 1 GND VSUP1 VSUP2 VCC1 GND VCC0 GND VCC2 GND DATA SHEET • SKY65362-11: HIGH-POWER RF FEM 36 35 34 33 32 31 30 29 28 GND PDETR 4 24 GND CSD 5 23 GND CPS 6 22 GND CTX 7 21 GND IALARM 8 20 ANT_1 ANT_SEL 9 19 GND 10 11 12 13 14 15 16 17 18 ANT_2 PDETF GND GND 25 RX_FLT 26 3 GND 2 LNA_IN GND GND GND GND 27 GND 1 RX PA_IN Y0206 Figure 2. SKY65362-11 Pinout – 36-Pin MCM (Top View) Table 1. SKY65362-11 Signal Descriptions Pin Name Description Pin Name Description 1 PA_IN PA input 19 GND Ground 2 GND Ground 20 ANT1 Antenna 1 3 PDETF Forward power detector output 21 GND Ground 4 PDETR Reverse power detector output 22 GND Ground 5 CSD Standby control (see Table 9) 23 GND Ground 6 CPS Receive mode gain control (see Table 9) 24 GND Ground 7 CTX Transmit/receive control (see Table 9) 25 GND Ground 8 IALARM PA current alarm output (see Table 9) 26 GND Ground 9 ANT_SEL Antenna select control input (see Table 9) 27 GND Ground 10 RX Receive output 28 GND Ground 11 GND Ground 29 VCC2 PA voltage supply 12 GND Ground 30 GND Ground 13 GND Ground 31 VCC0 Decoupling capacitor 14 LNA_IN LNA input 32 GND Ground 15 GND Ground 33 VCC1 PA voltage supply 16 RX_FLT Receive path after internal switches that connect ANT1 and ANT2 34 VSUP2 FEM voltage supply 17 GND Ground 35 VSUP1 FEM voltage supply 18 ANT2 Antenna 2. No integrated filtering. 36 GND Ground Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 January 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202886B DATA SHEET • SKY65362-11: HIGH-POWER RF FEM Electrical and Mechanical Specifications Electrical specifications are provided in Tables 4 through 8. The state of the SKY65362-11 is determined by the logic provided in Table 9. The absolute maximum ratings of the SKY65362-11 are provided in Table 2. The recommended operating conditions are specified in Table 3. Table 2. SKY65362-11 Absolute Maximum Ratings (Note 1) Parameter Symbol Supply voltage (no RF) VCC Control pin (CSD, CPS, CTX, IALARM, and ANT_SEL) voltage Minimum Maximum Units –0.3 +6.0 V –0.3 VCC (VCC < 5 V) V Operating temperature TA –40 +85 C Storage temperature TSTG –40 +125 C Transmit input power PIN_TX_MAX +10 dBm Receive RF input power @ ANT1 or ANT2 ports PIN_RX_MAX +10 dBm Voltage Standing Wave Ratio @ ANT1 or ANT2 ports VSWR 10:1 – Electrostatic discharge: ESD 1000 V Human Body Model (HBM), Class 1C Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. SKY65362-11 Recommended Operating Conditions Minimum Typical Maximum Units Supply voltage Parameter VCC Symbol 4.75 5.00 5.25 V Operating temperature TA –40 +25 +85 C Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202886B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 9, 2015 3 DATA SHEET • SKY65362-11: HIGH-POWER RF FEM Table 4. SKY65362-11 DC Electrical Specifications (Note 1) (VCC = +5.0 V, TA = +25 C, as Measured on the SKY65362-11 Evaluation Board [De-Embedded to Device], Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units 515 mA ICC_TX27 ICC_TX24 POUT = +30.5 dBm (Note 2) POUT = +27 dBm POUT = +24 dBm 300 230 mA mA Quiescent current, transmit mode ICQ_TX No RF 85 mA Total supply current, receive mode ICC_RX 6 mA Total supply current, receive bypass mode ICC_RXBYP 820 μA Sleep supply current ICC_OFF Total supply current, transmit mode ICC_TX30 No RF 0.05 1.00 μA Note 1: Performance is guaranteed only under the conditions listed in this table. Note 2: Typical current listed into VSWR = 1:1. ICC = 700 mA into VSWR = 2.5:1 guaranteed by characterization. Table 5. SKY65362-11 Receive Mode Electrical Specifications (Note 1) (VCC = +5.0 V, TA = +25 C, as Measured on the SKY65362-11 Evaluation Board [De-Embedded to Device], All Unused Ports Terminated with 50 Ω, Input Port = ANT1, Output Port = RX, Unless Otherwise Noted) Parameter Symbol Frequency range f Gain S21_RX Test Condition Min Typical 900 Max Units 930 MHz 900 to 930 MHz 16 dB 2.5 dB Noise figure NF 900 to 930 MHz Third order input intercept point IIP3 900 to 930 MHz, –20 dBm/tone, 200 kHz tone separation –5 –2 dBm –15 –12 dBm 1 dB Input compression point IP1dB 900 to 930 MHz Antenna port return loss S11_RX 900 to 930 MHz, into 50 Ω, ANT1 or ANT2 port –12 –6 dB S22_RX ANT1 terminated in 50 Ω –12 –6 dB Turn-on/off time tON_RX, tOFF_RX Receive or receive bypass to “off,” “off” to receive or receive bypass, from 50% of CTX edge to 10% of final RF output power (Note 2) Gain in receive bypass mode S21_RXBYP –4 1 dB Input compression point in receive bypass mode IP1dB_RXBYP +10 Receive port return loss in receive or receive bypass mode 11 –3 Note 1: Performance is guaranteed only under the conditions listed in this table. Note 2: Not production tested. Guaranteed by characterization. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 January 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202886B μs dB dBm DATA SHEET • SKY65362-11: HIGH-POWER RF FEM Table 6. SKY65362-11 Transmit Mode Electrical Specifications (1 of 2) (Note 1) (VCC = +5.0 V, TA = +25 C, as Measured on the SKY65362-11 Evaluation Board [De-Embedded to Device], All Unused Ports Terminated with 50 Ω, Input Port = PA_IN, Outport Port = ANT1, Unless Otherwise Noted) Parameter Symbol Frequency range f Output power @ ANT1 port POUT Test Condition Min Typical 900 Max Units 930 MHz 900 to 930 MHz with specified matching network on EVB, CW, PIN = 0 dBm: dBm dBm dBm +30.5 +28 +26 VCC = 5.0 V VCC = 4.0 V VCC = 3.6 V PA power added efficiency PAE POUT = +30.5 dBm @ ANT1 port, 915 MHz 43 % Input return loss S11_TX 902 to 928 MHz –10 dB Small signal gain S21_900 902 to 928 MHz 33 dB Output return loss S22_TX 900 to 930 MHz, into 50 Ω, ANT1 and ANT2 ports –10 dB 900 to 930 MHz with specified matching network on EVB, CW, POUT = +30.5 dBm @ ANT1 port (Note 2) –35 –30 dBc 900 to 930 MHz with specified matching network on EVB, CW, POUT = +30.5 dBm @ ANT1 port (Note 2) –50 –45 dBc POUT = +30.5 dBm @ ANT1 port, resolution bandwidth = 100 kHz, CW (Note 3) –55 –50 dBm nd th th rd th th th 2 , 6 , 7 , and 10 harmonics (HD 2, 6, 7, and 10) th th 3 , 4 , 5 , 8 , and 9 harmonic (HD 3, 4, 5, 8, and 9) Non-harmonic spurious 2fo, 6fo, 7fo, 10fo 3fo, 4fo, 5fo, 8fo, 9fo Spurious Change in output power under VSWR POUT_VSWR VSWR = 2.5:1, CW, reference POUT = +30.5 dBm into 50 Ω (Note 3) +1.5 dB Turn-on/off time tON_TX, tOFF_TX “Off” to transmit or transmit to “off,” from 50% of CTX edge to 90% of final RF output power (Note 3) 11 μs Mode change time tMODE_CHANGE Transmit to receive or receive bypass, receive or receive bypass to transmit, from 50% of CTX edge to 10% of final RF output power (Note 3) 11 μs –3 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202886B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 9, 2015 5 DATA SHEET • SKY65362-11: HIGH-POWER RF FEM Table 6. SKY65362-11 Transmit Mode Electrical Specifications (2 of 2) (Note 1) (VCC = +5.0 V, TA = +25 C, as Measured on the SKY65362-11 Evaluation Board [De-Embedded to Device], All Unused Ports Terminated with 50 Ω, Input Port = PA_IN, Outport Port = ANT1, Unless Otherwise Noted) Max Units Forward power detect Parameter PFWD Up to VSWR = 2.5:1 0.35 1.2 V Reverse power detect PREV Up to VSWR = 2.5:1 0.35 1.2 V Power detector accuracy PDET_ACC VSWR = 2.5:1 (Note 3) ±1 dB Current alarm trigger output IALARM Low if ICC < 800 mA, High if ICC > 800 mA (Note 4) 800 mA Stability STAB CW, POUT = +30.5 dBm into 50 Ω, 0.1 to 20 GHz, load VSWR = 6:1 (Note 3) All non-harmonically related outputs < –43 dBm CW, POUT = +30.5 dBm into 50 Ω load, VSWR = 10:1 (Note 3) No permanent damage Ruggedness Symbol RUG Test Condition Min Typical Note 1: Performance is guaranteed only under the conditions listed in this table. Note 2: Harmonics above 5th are not production tested. Guaranteed by characterization. Note 3: Not production tested. Guaranteed by characterization. Note 4: Current Alarm trigger point is adjustable by external components R2, R3, R4, R5 in Figure 3. Contact Sales support for further information. Table 7. SKY65362-11 Diversity Antenna Electrical Specifications (Note 1) (VCC = +5.0 V, TA = +25 C, f = 900 MHz to 930 MHz, as Measured on the SKY65362-11 Evaluation Board [De-Embedded to Device], All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Isolation between ANT1 and ANT2 ports ISOL_ANT1/2 –20 dB ANT1 to ANT2 switching time, transmit mode tANT1-ANT2_TX (Note 2) 1 μs ANT1 to ANT2 switching time, receive mode tANT1-ANT2_RX (Note 2) 1 μs Note 1: Performance is guaranteed only under the conditions listed in this table. Note 2: Not production tested. Guaranteed by characterization. Table 8. SKY65362-11 Electrical Specifications: Control Logic Characteristics (Note 1) (TA = +25 C, as Measured on the SKY65362-11 Evaluation Board [De-Embedded to Device], Unless Otherwise Noted) Parameter Symbol Test Condition Control voltage: High Low VIH VIL (Note 2) Input current: High Low IIH IIL (Note 2) Current alarm output voltage VOH VCC = 5 V Min Typical 1.6 0 Max Units 3.6 0.3 V V 1 1 μA μA 3.3 Note 1: Performance is guaranteed only under the conditions listed in this table. Note 2: Not production tested. Guaranteed by characterization. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 January 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202886B V DATA SHEET • SKY65362-11: HIGH-POWER RF FEM Table 9. SKY65362-11 Mode Control Logic (Note 1) CPS (Pin 6) CSD (Pin 5) CTX (Pin 7) ANT_SEL (Pin 9) Sleep (all off) 0 0 0 X Receive bypass 0 1 0 X Receive LNA mode 1 1 0 X Transmit X 1 1 X ANT1 port enabled X X X 0 ANT2 port enabled X X X 1 Mode Note 1: “1” = 1.6 to 3.6 V, “0” = 0 to 0.3 V, “X” = don’t care. Evaluation Board Description Package and Handling Information The SKY65362-11 Evaluation Board is used to test the performance of the SKY65362-11 FEM. An Evaluation Board schematic diagram is provided in Figure 3. An assembly drawing for the Evaluation Board is shown in Figure 4. Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. Package Dimensions The PCB layout footprint for the SKY65362-11 is provided in Figure 5. Figure 6 shows the package dimensions for the 36-pin MCM, and Figure 7 provides the tape and reel dimensions. The SKY65362-11 is rated to Moisture Sensitivity Level 3 (MSL3) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, PCB Design and SMT Assembly/Rework Guidelines for MCM-L Packages, document number 101752. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202886B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 9, 2015 7 DATA SHEET • SKY65362-11: HIGH-POWER RF FEM J10 PFWD PREV IALARM ANT_SEL CTX R5 1Ω CPS R4 1Ω CSD R3 1Ω R2 1Ω L7 5.1 nH C14 1 nF C15 22 pF C10 100 pF PREV L5 1 kΩ L6 1 kΩ CSD CPS CTX IALARM ANT_SEL PA_IN GND PFWD PREV CSD CPS CTX IALARM ANT_SEL 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 J6 SMA 10 11 12 13 14 15 16 17 18 RX GND GND GND LNA_IN C11 100 pF GND GND GND GND GND GND GND ANT1 GND SKY65362 U2 GND RX_FLT PFWD 1 2 3 4 5 6 7 8 9 GND VSUP1 VSUP2 VCC1 GND VCC0 GND VCC2 GND PAD 37 C17 10 nF J7 L8 22 nH C12 DNI C16 10 nF SMA C13 33 pF 2 4 6 8 10 12 14 16 18 20 22 24 26 28 GND ANT2 C18 4.7 µF 1 3 5 7 9 11 13 15 17 19 21 23 25 27 J8 SMA J9 SMA Figure 3. SKY65362-11 Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 January 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202886B Y1558 DATA SHEET • SKY65362-11: HIGH-POWER RF FEM Y1557 Figure 4. SKY65362-11 Evaluation Board Assembly Drawing Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202886B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 9, 2015 9 DATA SHEET • SKY65362-11: HIGH-POWER RF FEM 6.3 mm Pin 36 Pin 1 Indicator 0.20 x 0.20 36X 0.75 mm 36X 0.25 mm Pin 1 Stencil aperture size of 80% to 100% of the module/package solder mask openings 6.3 mm 9X 0.875 mm Exposed center pads Package Outline 9X 0.875 mm 0.125 mm Typ 0.5 mm Pitch Stencil Aperture Pin 36 6.3 mm 6.4 mm Pin 36 Pin 1 Indicator 0.20 X 0.20 34X 0.75 mm 34X 0.25 mm Pin 1 36X 0.4 mm Pin 1 0.6 mm Pitch Thermal via array ø0.3 mm on 0.6 mm pitch improves thermal performance 36X 0.85 mm Opening size of 60% to 100% of the exposed center opening shown 2X 1.4375 mm 6.4 mm 6.3 mm 0.25 mm Typ Package Outline Package Outline 0.6 mm Pitch 2X 1.4375 mm 0.5 mm Pitch 0.5 mm Pitch Metallization Solder Mask Opening Notes: 1. All dimensions are in millimeters, unless otherwise specified. 2. Thermal vias should be resin filled and capped in accordance with IPC-4761Type VII vias. Recommended Cu thickness is 30 to 35 µm. Figure 5. SKY65362-11 PCB Layout Footprint Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 January 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202886B Y1554 C Pin 36 0 Pin 1 Indicator 36X SMT Pad 0.1 M A B C Top B 4X 2 6 10X 1 DATA SHEET • SKY65362-11: HIGH-POWER RF FEM Pin 1 Indicator See Detail D Pin 1 4X 2 10X 1 4X 0.5 6 0 4X 1.5 4X 1.5 A 0.9 ± 0.1 0.15 A B C 0.1 Top View Solder Mask Openings 0.2 A B C See Detail B Bottom View Side View 0.875 (0.1) 0.5 ± 0.1 4X 0.5 See Detail A 0.875 0.875 0.875 0.4 ± 0.05 0.25 ± 0.05 Pin 1 Indicator 0.2 X 0.2 5X R0.05 Max 4X R0.05 Max Metal Pad Edge Detail B Scale: 2X 8X This Rotation Detail A Detail C Scale: 2X 1X This Rotation Scale: 2X 9X This Rotation 9X Rotated 180 º 9X Rotated 90 ºCW 9X Rotated 90 ºCCW Notes: 1. Dimensions and tolerances per ASME Y14.5-1994. 2. All dimensions are in millimeters unless otherwise specified. 3. Pad definitions per details on drawing. Y1555 Figure 6. SKY65362-11 36-Pin MCM Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202886B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 9, 2015 11 DATA SHEET • SKY65362-11: HIGH-POWER RF FEM 8.00 (P1) Ø1.50 ±0.10 4.00 (Po) 2.00 ±0.05 B 1.75 ±0.10 5.50 ±0.05 Pin 1 Refer to Special Notes A 6.35 (Bo) A 12.00 ±0.30 0.3 ±0.02 7° Max 1.59 (Ko) B Ø1.50 Min Section B-B Notes: 1. Carrier tapes must meet all requirements of Skyworks GP01-D233 procurement spec for tape and reel shipping. 2. Carrier tape shall be black conductive polystyrene. 3. Cover tape shall be transparent conductive pressure sensitive adhesive (PSA) material with 9.30 mm width. 4. ESD-surface resistivity shall be <=1 x 10 10ohms/square per EIA, JEDEC TNR specification. 5. Po/P1 10 pitches cumulative tolerance on tape: ±0.20 mm. 6. Ao & Bo measurement point to be 0.30 mm from bottom pocket. 7. All dimensions are in millimeters. 8. Part Number: eC3-MCM0606-12-8-F3-L (Please indicate on Purchase Order) 6.35 (Ao) 8° Max Special Notes: 1. Pin 1 orientation shall be on the Top Left for the: SKY73022-21 and -31 SKY73023-21 and -31 2. Pin 1 orientation shall be on the Top Right for all other 6 x 6 mm MCMs and RFLGAs. Section A-A Y1556 Figure 7. SKY65362-11 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 January 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202886B DATA SHEET • SKY65362-11: HIGH-POWER RF FEM Ordering Information Model Name SKY65362-11: High-Power RF FEM Manufacturing Part Number SKY65362-11 Evaluation Board Part Number SKY65362-11-EK1 Copyright © 2013-2015 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202886B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 9, 2015 13