PRELIMINARY DATA SHEET SKY65329-NP: 900 MHz Front-End Module Applications Description • Paging Skyworks SKY65329-NP is a fully matched, high-efficiency RF Front-End Module (FEM) with 900 MHz transmit and receive paths. There are also routing switches to connect auxiliary broadband signals between the RFIC and antenna ports. By using three control signals (CTRL1, CTRL2, and PWR_DOWN), the module can be configured to one of five operational modes (900 MHz transmit, 900 MHz receive, auxiliary RF bypass, auxiliary power, or power down). • Remote metering • WLL and ISM transmitters Features • 900 MHz transmit saturated output power > 24 dBm The 900 MHz transmit path consists of an harmonic filter and high efficiency Power Amplifier (PA). The 900 MHz receive path contains a low-power Low-Noise Amplifier (LNA). Both the PA and LNA can be switched to power-down mode for low leakage current. The auxiliary RF path is a low-loss, broadband, bidirectional RF path that allows easy switching of signal between the RFIC and the antenna port. • 900 MHz high efficiency PA and LNA • Auxiliary bidirectional broadband RF path • Internal switching and control circuits • Internal RF match and bias circuits • Internal DC block on RF ports • Externally adjustable bias setting Breakout ports are available for adding external filters. Switchable auxiliary power can supply up to 10 mA of VDD power to external circuitry through pin 26 (VDD_OUT). • Single DC supply = 3.6 V • Small footprint, MCM (28-pin, 8 x 8 mm) Pb-free (MSL3, 260 °C per JEDEC J-STD-020) SMT package The SKY65329-NP is manufactured with advanced InGaP HBT and silicon CMOS processes, which provide a positive DC voltage supply while maintaining high efficiency and good linearity. The device is mounted in a 28-pin, 8 x 8 mm MCM SurfaceMounted Technology (SMT) package, which allows for a highly manufacturable low-cost solution. A block diagram of the SKY65329-NP is shown in Figure 1. The device package and pinout for the 28-pin MCM are shown in Figure 2. Filter 1 Filter 2 Harmonic Filter Bidirectional RF Port PA Switch A Switch B LNA Antenna Port Switch D Switch C Filter 3 Filter 4 S1336 Figure 1. SKY65329-NP Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200995A • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • March 4, 2009 1 CTRL2 VDD_OUT VCC_PA VREF VDD_CONT 27 26 25 24 23 21 GND GND 3 20 ANT RFIO 4 19 GND GND 5 18 FLT3_I FLT1_I 6 17 FLT4_I GND 7 16 GND FLT1_O 8 15 FLT3_O 9 10 11 12 13 14 VCC_LNA 2 LNA_BIAS_R GND FLT2_I 22 GND FLT4_O 28 FLT2_O 1 GND PWR_DOWN CTRL1 PRELIMINARY DATA SHEET • SKY65329-NP TRANSMIT/RECEIVE FRONT-END MODULE S1337 Figure 2. SKY65329-NP Pinout – 28-Pin MCM (Top View) Table 1. SKY65329-NP Control Logic Logic Input Control Bits Configuration States CTRL1 CTRL2 PWR_DOWN PA LNA VDD Output Auxiliary power 0 0 0 Off Off On 900 MHz receive 0 1 0 Off On Off 900 MHz transmit 1 0 0 On Off Off Auxiliary RF bypass 1 1 0 Off Off Off Power down X X 1 Off Off Off Note: Logic level 0: 0 V to 0.3 V Logic level 1: 2.5 V to VCC. Technical Description The SKY65329-NP provides input and output amplifier stages and is internally matched for optimum efficiency. An active bias circuit provides both input and output stages with excellent gain tracking over temperature and voltage variations. The module operates with positive DC voltages, and maintains high efficiency and good linearity. The nominal operating voltage is 3.6 V for maximum power, but the device can be operated at slightly lower voltages for other mobile applications. Operational Modes By using three control signals (CTRL1, CTRL2, and PWR_DOWN), the module can be configured to one of five operational modes: Auxiliary power. In this mode, the PA and LNA are off and the VDD_OUT signal (pin 26) can be used for auxiliary power, which can supply up to 10 mA of VDD power to external circuitry. 900 MHz receive. In this mode, the SKY65329-NP amplifies the received signal at the antenna port through the LNA. 900 MHz transmit. In this mode, the transmit path provides an harmonic filter and high efficiency PA. Auxiliary RF bypass. In this mode, a low-loss broadband bidirectional RF path allows easy switching of the signal between the transceiver and the antenna port. Power down. In this mode, the PA and LNA are powered down for minimal current consumption and low leakage current (5 μA). Table 1 provides the control logic for each of the five operational modes. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 March 4, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200995A PRELIMINARY DATA SHEET • SKY65329-NP TRANSMIT/RECEIVE FRONT-END MODULE Electrical and Mechanical Specifications Signal pin assignments and functional pin descriptions are described in Table 2. The absolute maximum ratings of the SKY65329-NP are provided in Table 3. The recommended operating conditions are specified in Table 4 and electrical specifications are provided in Table 5. Package and Handling Information Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SKY65329-NP is rated to Moisture Sensitivity Level 3 (MSL3) at 260 °C. It can be used for lead or lead-free soldering. For additional information, refer to Skyworks Application Note, PCB Design and SMT Assembly/Rework Guidelines for MCM-L Packages, document number 101752. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. For packaging details, refer to the Skyworks Application Note, Tape and Reel, document number 101568. Table 2. SKY65329-NP Signal Descriptions Pin # Name Description Pin # 15 Name FLT3_O Description 1 PWR_DOWN Power down Filter 3 output port 2 FLT4_O Filter 4 output port 16 GND Ground 3 GND Ground 17 FLT4_I Filter 4 input port 4 RFIO RF input/output (internally DC blocked) 18 FLT3_I Filter 3 input port 5 GND Ground 19 GND Ground 6 FLT1_I Filter 1 input port 20 ANT Antenna port (internally DC blocked) 7 GND Ground 21 GND Ground 8 FLT1_O Filter 1 output port 22 GND Ground 9 GND Ground 23 VDD_CONT CMOS controller supply voltage 10 FLT2_O Filter 2 output port 24 VREF PA bias reference voltage 11 GND Ground 25 VCC_PA PA collector voltage 12 FLT2_I Filter 2 input port 26 VDD_OUT Auxiliary supply 13 LNA_BIAS_R LNA bias resistor 27 CTRL2 Control 2 14 VCC_LNA LNA collector voltage 28 CTRL1 Control 1 Table 3. SKY65329-NP Absolute Maximum Ratings (Note 1) Parameter Symbol Minimum Maximum Units Supply voltage VCC Transmit input power PIN_TX 4 dBm V Receive input power PIN_RX dBm Supply current ICC mA Power dissipation PDISS W Case operating temperature TC –40 +85 °C Storage temperature TST –55 +125 °C Junction temperature TJ +150 °C Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200995A • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • March 4, 2009 3 PRELIMINARY DATA SHEET • SKY65329-NP TRANSMIT/RECEIVE FRONT-END MODULE Table 4. SKY65329-NP Recommended Operating Conditions Parameter Symbol Minimum Typical Maximum Units 2.8 3.6 3.8 V Supply voltage VCC Frequency range f 902 928 MHz Auxiliary frequency range fAUX 400 2500 MHz Transmit input power range PIN –3 –1 dBm Case operating temperature TC –40 +85 °C Storage temperature TST –55 +125 °C Table 5. SKY65329-NP Electrical Specifications (VCC = 3.6 V, TC = +25 °C, External PA VCC Bias Resistor [R28] = 2 kΩ, Unless Otherwise Noted) Parameter Symbol Test Condition Min All RF ports except ANT in transmit mode, 50 Ω 12 Typical Max Units General Return loss RL Thermal resistance ΘJC dB °C/W 22 Auxiliary Power Mode Auxiliary power VCC Ext Load current < 10 mA VCC – 0.1 VCC V 900 MHz Receive Mode (0 Ω Between FLT1_I/FLT1_O and FLT3_I/FLT3_O Pins in Place of External Filters) Small signal gain GSS (Rx) CW 18.5 dB Noise Figure NF (Rx) 2.0 dB Input 1dB compression IP1dB (Rx) CW –13 dBm Input IP3 IIP3 Two –30 dBm CW tones –2 dBm Operating current IOP (Rx) POUT = IP1dB (Rx) 4.5 mA +24.3 dBm 900 MHz Transmit Mode (0 Ω Between FLT1_I/FLT1_O and FLT2_I/FLT2_O Pins in Place of External Filters) +21.0 Saturated output power PSAT CW, PIN = –3 dBm CW, PIN = –1 dBm +24.9 Saturated output power cold droop (Note 1) DPSATCold CW, VCC = 2.8 V, TC = –40 °C 2 Small signal gain GSS (Tx) CW 28 dB Noise Figure NF (Tx) CW 7.5 dB Power Added Efficiency PAE CW, PIN = –3 dBm 48.0 % CW, PIN = –1 dBm 48.6 % nd dBm 3 dB 2 harmonic Pf2 CW, PIN = –3 dBm –39 –30 dBc 3rd to 8th harmonic Pf3 to Pf8 CW, PIN = –3 dBm –66 –60 dBc Operating current IOP (Tx) CW, PIN = –3 dBm 150 mA 167 mA Output return loss ORL (Tx) CW, PIN = –1 dBm CW, PIN = –3 dBm 8 dB Auxiliary RF Bypass Mode (0 Ω Between FLT4_I and FLT4_O Pins in Place of External Filters) 450 MHz loss IL (Aux) f = 450 MHz 1.5 ILEAK No RF input 0.2 2.5 dB FEM Power-Down Mode Leakage current Note 1: Saturated transmit output power cold droop is defined as the drop in PSAT at VCC = 2.8 V and TC = –40 °C relative to PSAT at VCC = 3.6 V and TC = +25 °C. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 March 4, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200995A μA PRELIMINARY DATA SHEET • SKY65329-NP TRANSMIT/RECEIVE FRONT-END MODULE Evaluation Board Description The SKY65329-NP Evaluation Board is used to test the performance of the SKY65329-NP FEM. The Evaluation Board schematic diagram is shown in Figure 3. An assembly drawing for the Evaluation Board is shown in Figure 4 and the layer detail is provided in Figure 5. The layer detail physical characteristics are noted in Figure 6. Table 6 provides the Bill of Materials (BOM) list for Evaluation Board components. The four external filters shown in Figure 3 are configured as throughputs so that the device can be tested immediately. External resistors are installed with values that allow the unit to operate immediately with the electrical specifications provided in Table 4. Refer to the SKY65329 T/R FEM Evaluation Board Information Application Note (document # *** TBD ***) for additional testing information. The digital ground pin of the SKY65329-NP (pin 22) is not connected to the other ground pins internally. Therefore, an external common ground connection is needed. If this is not provided, the digital controller may operate at a different potential than the RF section, which could damage the part. 2. The ground pads of the SKY65329-NP have special electrical and thermal grounding requirements. These pads are the main thermal conduit for heat dissipation. Since the circuit board acts as the heat sink, it must shunt as much heat as possible from the device. Therefore, design the connection to the ground pad to dissipate the maximum wattage produced by the circuit board. Multiple vias to the grounding layer are required. 3. Two external output bypass capacitors (0.022 μF and 22 μF) are required on pin 25 (VCC_PA). The same two capacitor values are also required on pin 14 (VCC_LNA). The capacitors should be placed in parallel between the supply line and ground. 4. Pins 14 and 25 (VCC_LNA and VCC_PA, respectively) may be connected together at the supply. NOTE: A poor connection between the slug and ground increases junction temperature (TJ), which reduces the lifetime of the device. The separate digital ground pin allows flexibility when connecting the ground between the digital and RF sections of the device. This connection is through resistor R21 and capacitor C11 (loaded with a 0 Ω resistor by default). If RF isolation is desired between the digital and RF sections, an appropriate component may be placed instead. Pin 16 of connector P1 is used to connect the source of the digital controls to a common ground point with the test fixture through components R21 and C11. Package Dimensions Circuit Design Considerations The SKY65329-NP is a static-sensitive electronic device. Do not operate or store near strong electrostatic fields. Take proper ESD precautions. The following design considerations are general in nature and must be followed regardless of final use or configuration: The phone board layout footprint for the SKY65329-NP is shown in Figure 7. Package dimensions for the 28-pin MCM are shown in Figure 8, and tape and reel dimensions are provided in Figure 9. Electrostatic Discharge (ESD) Sensitivity 1. Paths to ground should be made as short as possible. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200995A • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • March 4, 2009 5 PRELIMINARY DATA SHEET • SKY65329-NP TRANSMIT/RECEIVE FRONT-END MODULE P1 9 10 11 12 13 VCC_PA 14 15 16 17 18 VDD_CONT 8 GND (Digital) 7 PA_VCC_SENSE 6 CTRL1 5 PWR_DOWN 4 VDD_OUT 3 CTRL2 2 VCC_LNA 1 R4 0Ω VDD Output C4 2200 pF PA VCC Sense R2 0Ω PA VCC C3 2200 pF 2 R6 DNI R8 DNI VDD_CONT FLT1_I FLT4_I GND 8 FLT1_O R9 DNI 9 10 11 12 GND 13 VCC_LNA 50 Ω Transmission Line FLT3_I LNA_BIAS_R R7 0Ω VREF GND 19 50 Ω Transmission Line R11 DNI R12 0Ω Antenna 17 16 FLT3_O 15 50 Ω Transmission R16 Line DNI 14 R17 DNI R18 0Ω R20 50 Ω Transmission Line DNI J6 R19 DNI R15 5600 Ω 50 Ω Transmission R10 Line DNI J8 18 J3 J4 Digital Ground C11 DNI 21 4 RFIO GND R21 0Ω 22 ANT 20 7 50 Ω Transmission R5 Line DNI GND GND 6 VDD Controller C12 2200 pF 23 SKY65329-NP C8 DNI R22 0Ω FLT4_O 5 J2 24 FLT2_I 50 Ω Transmission Line PWR_DOWN 25 C10 22 μF C9 2200 pF GND 3 J1 26 GND C1 2200 pF 27 VCC_PA 1 GND R1 0Ω Power Down CTRL1 28 VDD_OUT C2 2200 pF CTRL2 R3 0Ω Control Voltage 1 R28 2000 Ω FLT2_O Control Voltage 2 J7 50 Ω Transmission Line R14 DNI LNA VCC C6 2200 pF R13 DNI C7 DNI C5 22 μF J5 J10 50 Ω Transmission Line R23 DNI R24 DNI R25 0Ω R27 DNI 50 Ω Transmission Line Note: Some component labels may be different than the corresponding component symbol shown here. Component values, however, are accurate as of the date of this Data Sheet. Figure 3. SKY65329-NP Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 J9 R26 DNI March 4, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200995A S1342 PRELIMINARY DATA SHEET • SKY65329-NP TRANSMIT/RECEIVE FRONT-END MODULE J10 J9 J8 J7 R28 R19 R25 R23 R27 J2 C8 R26 R24 J1 R5 R6 R8 R18 R17 R7 R16 R9 C6 C7 R15 J3 J6 R10 R11 R13 R14 R12 C10 C5 C12 C11 R1 R2 R3 R4 R21 J4 C4 R22 C1 C2 C3 J5 P1 S1343 Figure 4. SKY65329-NP Evaluation Board Assembly Drawing Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200995A • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • March 4, 2009 7 PRELIMINARY DATA SHEET • SKY65329-NP TRANSMIT/RECEIVE FRONT-END MODULE Layer 1: Top – Metal Layer 2: Ground Layer 3: Power Plane Layer 4: Solid Ground Plane S1344 Figure 5. SKY65329-NP Evaluation Board Layer Detail Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 March 4, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200995A PRELIMINARY DATA SHEET • SKY65329-NP TRANSMIT/RECEIVE FRONT-END MODULE Cross Section Name Thickness (mm) Material εr L1 0.0356 Cu – Lam1 0.3048 Rogers 4003-1 3.38 L2 (GND) 0.0356 Cu 1 oz – Lam2 0.1016 FR4 4.35 L3 (GND) 0.0356 Cu 1 oz – Lam3 0.3048 FR4-12 4.35 L4 0.0356 Cu 1 oz – S1339 Figure 6. Layer Detail Physical Characteristics Table 6. SKY65329-NP Evaluation Board Bill of Materials Component Quantity Size Value Vendor Part Number C1, C2, C3, C4, C6, C9, C12 7 0402 2200 pF Murata GRM155R71H222KA01 C5, C10 2 0805 22 μF Murata GRM21BR60J226KA11 R1, R2, R3, R4, R7, R12, R18, R21, R22, R25 10 0402 0Ω Yageo RC0402JR-*18RL R28 1 0402 2000 Ω Yageo RC0402JR-*2KL R15 1 0402 5600 Ω Yageo C7, C8, C11, R5, R6, R8, R9, R10, R11, R13, R14, R16, R17, R19, R20, R23, R24, R26, R27 19 N/A DNI N/A RC0402JR-*5K6L N/A Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200995A • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • March 4, 2009 9 PRELIMINARY DATA SHEET • SKY65329-NP TRANSMIT/RECEIVE FRONT-END MODULE 8.3 Stencil Aperture Size For Center Ground Pad Should Be 80% to 100% (By Area) of the Solder Mask Opening of the Package 0.75 0.65 0.05 0.15 0.85 0.951 12X 0.063 Stencil and Metallization 8.3 36X 0.875 Component Outline Soldermask Opening SMT Pad Detail Scale: 2X 6X This Rotation 6X Rotated 180o 6X Rotated 90o CW 6X Rotated 90o CCW 24X 0.125 Component Outline 12X 0.063 24X 0.125 36X 0.875 8.4 Stencil Aperture Top View 5.875 2X 1.15 2X 0.15 0.05 All Around 2X 0.15 8.4 5.875 Stencil and Metallization Soldermask Opening Component Outline 2X 0.85 2X 0.95 SMT Pad Detail Scale: 2X 1X This Rotation 1X Rotated 180o 1X Rotated 90o CW 1X Rotated 90o CCW Pin 28 Component Outline Solder Mask Opening Top View 8.3 2X 3.725 Pin 1 Thermal Via Array. ∅0.3 mm on 0.6 mm pitch. Additional vias in common ground pad will improve thermal and electrical performance NOTE: thermal vias should be tented and filled with solder mask, 30-35 μm Cu plating recommended. 2X 3.725 8.3 4X 0.5 (1.2) 1.0 Pitch Typ Component Outline (1.2) 0.25 Typ Metallization Top View Note: The cross-hatched area represents the merger of the center ground pad +8 individual I/O ground pads. All I/O ground pads should have at least one via connected to internal ground planes for optimum electrical performance. All measurements are in millimeters S1340 Figure 7. SKY65329-NP Phone Board Layout Footprint Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 March 4, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200995A See Detail D 16X 0.5 16X 1.5 C 16X 2.5 B 8 Pin 1 Indicator 16X 3.9 PRELIMINARY DATA SHEET • SKY65329-NP TRANSMIT/RECEIVE FRONT-END MODULE Pin 28 Pin 1 Indicator (See Detail C) Pin 1 16X 3.9 16X 2.5 A 16X 1.5 16X 0.5 8 0 B 28X SMT Pad 0.1 A B C A 0 36X Solder Mask Openings 1.05 ± 0.1 0.2 0.15 A B C A B C 0.1 Top View Side View Bottom View Metal Pad All Edges 0.6 ± 0.05 (0.1) 3X (0.05) 0.75 ± 0.05 0.2 x 0.2 2X 0.6 ± 0.05 4X (0.05) 0.65 ± 0.05 Metal Pad All Edges 0.875 0.875 2X (0.1) 0.875 0.875 2X 0.8 ± 0.05 Detail A Detail B Detail C Pad Scale: 2X Pad Scale: 2X Scale: 2X 6X This rotation 6X Rotated 180o 6X Rotated 90o CW 6X Rotated 90o CCW 1X This rotation 1X Rotated 180o 1X Rotated 90o CW 1X Rotated 90o CCW Soldermask Edges Soldermask Edges 35 X Detail D Scale: 2X All measurements are in millimeters Dimensioning and tolerancing according to ASME Y14.5M-1994 S1341 Figure 8. SKY65329-NP 28-Pin MCM Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200995A • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • March 4, 2009 11 PRELIMINARY DATA SHEET • SKY65329-NP TRANSMIT/RECEIVE FRONT-END MODULE 2.00 ± 0.05 12.00 4.00 Pin #1 indicator ∅1.55 ± 0.05 5o A 1.75 ± 0.10 7.50 ± 0.05 B A 16.00 ± 0.03 0.30 ± 0.05 8.35 ∅1.50 Min. B 1.70 B 5o Notes: 1. Carrier tape: black conductive polystyrene 2. Cover tape material: transparent conductive PSA 3. Cover tape size: 13.3 mm width 4. All dimensions are in millimeters 5. Pin 1 orientation is in top left corner for the following Skyworks products: 8.35 A SKY74963-xx CX74063-35 SKY77503-xx SKY77506-xx SKY77512-xx SKY77526-xx SKY77343-xx For all other 8 x 8 mm MCM/RFLGA products, pin 1 orientation is in top right corner. Figure 9. SKY65329-NP 28-Pin MCM Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 March 4, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200995A S1290 PRELIMINARY DATA SHEET • SKY65329-NP TRANSMIT/RECEIVE FRONT-END MODULE Ordering Information Model Name SKY65329-NP 900 MHz Front-End Module Manufacturing Part Number SKY65329-NP (Pb-free package) Evaluation Kit Part Number TW17-D390 Copyright © 2009 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200995A • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • March 4, 2009 13