Ten-X® 10 mm switching solenoid valve FEATURES · 3-way, 2 position (NO, NC & Distributor) · Optional ‘Hit and Hold’ drive electronics using pulse width modulation (PWM) for low power consumption · Minimum flow of 8 lpm @ 6 psi and 22 lpm @ 30 psi · Over 20 million cycles · 10 mm single piece body design · Barbed pressure ports allow for direct tubing or manifold assemblies · RoHS compliant PHYSICAL PROPERTIES MEDIA COMPATIBILITY Non-reactive gases Operating environment (continuous duty) Storage temperature WETTED MATERIALS PBT (polybutylene terephthalate) glass filled; 430FR series stainless steel; 302 series stainless steel; silicone, EPDM or Viton (FKM) elastomer Voltage Electrical connections Porting 1.0 W 0.5 W -40...70 °C 10 mm (centerline) Barbs for 1.98 mm (0.078 in) I.D. tubing or manifold mount with gasket Weight without electronics with electronics ELECTRICAL Power 914...2... (Type 2), 914...6... (Type 6) all other Spacing 0...50 °C Internal volume 10.7 g 12 g 0.131 cm3 (0.0080 in3) 5, 12, 24 VDC PC pins Ten-X is a registered trademark of Parker Hannifin Corporation. E / 11260 / D 1/4 www.first-sensor.com www.sensortechnics.com Ten-X® 10 mm switching solenoid valve PERFORMANCE CHARACTERISTICS Part no. Pressure Minimum flow 914-1... (silicone elastomer) 0...6 psi 914-2... (Viton & EPDM elastomer) 0...6 psi, 0...20 psi, 0...30 psi Orifice siz es/ Equivalent CV1 8 lpm @ 6 psi, 0.060" (1.52 mm)/ 22 lpm @ 30 psi 0.042 CV Leak rate2 Response ≤0.016 sccm <5 ms cycling ≤0.2 sccm <20 ms cycling FLOW CURVES (typical air flow at 24 °C)3 Flow (slpm) 6 psi devices Pressure (psi) Flow (slpm) 20 psi and 30 psi devices Pressure (psi) Notes: 1 The CV value is the volume flow in US gallons/min under specific flow conditions and describes the relative flow capacity of a valve. The equivalent european measure is the kV value expressed in m3/h (kV = 0.86 CV). 2 sccm denotes Standard Cubic Centimeters per Minute. It is a unit for the flow rate at standard conditions of temperature and pressure. 1000 sccm = 1 slpm. 3 slpm denotes Standard Liters per Minute. It is a unit for the flow rate at standard conditions of temperature and pressure. 1 slpm = 1000 sccm. E / 11260 / D 2/4 www.first-sensor.com www.sensortechnics.com Ten-X® 10 mm switching solenoid valve OUTLINE DRAWING AND MANIFOLD MOUNT DIAGRAM 6 psi devices 1.139 (28.93) 0.020 (0.5) sq. pins 0.077 (1.96) 0.575 0.375 (14.61) Long pin (9.53) Short pin 0.475 (12.07) 0.170 (4.32) Normally open port Common port Normally closed port 0.148 (3.75) Ø 0.120 (3.05) 0.030 (0.76) for use with wire hold down for PCB mounting Barb fittings for 0.078 (1.98) I.D. polyurethane tubing Ø 0.093 (2.36) 0.976 (24.79) 0.212 (5.38) 2-56 UNC-2B 0.766 (19.46) dimensions in inches (mm) 0.871 (22.12) 0.197 (5.0) 0.394 (10.01) 0.394 (10.01) 0.390 (9.91) 0.195 (4.95) 0.174 (4.42) 0.236 (6.00) Feature for 2-56 screw for valve mounting 0.870 (22.10) 0.766 (19.46) 0.976 (24.79) 0.207 (5.26) 1.25 (31.78) Ø 0.090 Ø 0.132 ±0.001 x 0.180 Ø 0.154 ±0.003 x 0.055 ±0.002 c'drill 40° to Ø 0.132 (Ø 2.29 Ø 3.35 ±0.025 x 4.57 Ø 3.91 ±0.076 x 1.4 ±0.05 c'drill 40° to Ø 3.35) 20 psi and 30 psi devices with electronics 1.303 (33.10) 0.025 (0.64) sq. pins 1.174 (29.81) 0.212 (5.38) 0.100 (2.54) 0.361 (9.17) 0.619 (15.72) Normally open port Common port Normally closed port 0.170 (4.32) Ø 0.120 (3.05) 0.035 (0.89) Ø 0.093 (2.36) 0.976 (24.79) 0.267 (6.78) 0.766 (19.46) 2-56 UNC-2B 0.871 (22.12) Feature for 2-56 screw for valve mounting 0.870 (22.10) 0.262 (6.65) 0.197 (5.0) 0.394 (10.01) 0.394 (10.01) 0.390 (9.91) 0.195 (4.95) E / 11260 / D dimensions in inches (mm) Barb fittings for 0.078 I.D. polyurethane tubing 0.766 (19.46) 0.976 (24.79) Ø 0.090 Ø 0.132 ±0.001 x 0.180 Ø 0.154 ±0.003 x 0.055 ±0.002 c'drill 40° to Ø 0.132 (Ø 2.29 Ø 3.35 ±0.025 x 4.57 Ø 3.91 ±0.076 x 1.4 ±0.05 c'drill 40° to Ø 3.35) 3/4 www.first-sensor.com www.sensortechnics.com Ten-X® 10 mm switching solenoid valve ORDERING INFORMATION 6 psi devices Series Options 914 Elastomer 1 Silicone Type 1* 2 way, NO, 6 psi 2 Viton (FKM) 2** 2/3 way, NC, 6 psi 3 EPD M Model 1 Standard (without electronics) 6** Distributor, 6 psi Voltage 05 5 VDC 12 12 V D C Electical 1 Short pins 2 Accessories* 000 none Long pins 24 24 V D C 7* 3 way, NO, 6 psi * Silicone & EPDM only ** Viton (FKM) only Example: 914 1 1 * please order separately 1 05 1 000 20 psi and 30 psi devices with electronics Series Options 914 Elastomer Type Model 2 Integrated electronics Voltage 2 Viton (FKM) 3 2/3 way, NC, 30 psi 05 5 VDC 3 EPD M 4 2/3 way, NO, 30 psi 12 12 V D C 5 Distributor, 20 psi 24 24 V D C Electical 3 Pins (2.54 mm) Accessories* 000 none * please order separately Example: 914 2 3 2 05 3 000 Note: Not all combinations might be available. Please contact First Sensor for further information. Accessories (please order separately using the following order numbers) Order No. Description 191-000112-010 (extra charge) Mounting screws for 6 psi devices (2 screws per valve) 191-000112-012 (extra charge) Mounting screw for 20 psi and 30 psi devices (2 screws per valve) 195-000211-001 (extra charge) Manifold gasket (FKM) (1 gasket per valve) 195-000242-001 (extra charge) Manifold gasket (EPDM) (1 gasket per valve) 590-000073-001 (extra charge) 18 " leads w/ connector (only for devices with integrated electronics) First Sensor reserves the right to make changes to any products herein. First Sensor does not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. E / 11260 / D 4/4 www.first-sensor.com www.sensortechnics.com