Ten-X® 10 mm switching soleniod valve FEATURES · 3-way, 2 position (NO, NC & Distributor) · Optional ‘Hit and Hold’ drive electronics using pulse width modulation (PWM) at 25-32 kHz · Minimum flow of 8 lpm @ 6 psi and 22 lpm @ 30 psi · 10 mm single piece body design · Barbed pressure ports allow for direct tubing or manifold assemblies · RoHS compliant MEDIA COMPATIBILITY Non-reactive gases WETTED MATERIALS PHYSICAL PROPERTIES PBT (polybutylene terephthalate) glass filled; 430FR series stainless steel; 302 series stainless steel; Viton (FKM) or silicone elastomer Operating environment (continuous duty) 0 to 50 °C Storage temperature Spacing ELECTRICAL Power Voltage Electrical connections Porting 0.5 W 5, 12, 24 VDC PC pins -40 to 70 °C 10 mm (centerline) Barbs for 1.98 mm (0.078 in) I.D. tubing or manifold mount with gasket Weight without electronics with electronics Internal volume 10.7 g 12 g 0.131 cm3 (0.0080 in3) Ten-X is a registered trademark of Parker Hannifin Corporation. E / 11260 / A 1/4 www.sensortechnics.com Ten-X® 10 mm switching soleniod valve PERFORMANCE CHARACTERISTICS Part no. Pressure 914-1... (silicone elastomer) 0...6 psi 914-2... (Viton elastomer) 0...6 psi, 0...20 psi, 0...30 psi Minimum flow 8 lpm @ 6 psi, 22 lpm @ 30 psi Orifice siz es/ Equivalent CV1 0.060" (1.52 mm)/ 0.042 CV Leak rate2 Response ≤0.016 sccm <5 ms cycling ≤0.2 sccm <20 ms cycling FLOW CURVES (typical air flow at 24 °C)3 6 psi devices 20 psi and 30 psi devices Notes: 1 The CV value is the volume flow in US gallons/min under specific flow conditions and describes the relative flow capacity of a valve. If several valves with the same nominal diameter are compared, the valve with the highest CV value has the best flow dynamics design. The equivalent european measure is the kV value expressed in m3/h (kV = 0.86 CV). 2 sccm denotes Standard Cubic Centimeters per Minute. It is a unit for the flow rate at standard conditions of temperature and pressure. 1000 sccm = 1 slpm. 3 slpm denotes Standard Liters per Minute. It is a unit for the flow rate at standard conditions of temperature and pressure. 1 slpm = 1000 sccm. E / 11260 / A 2/4 www.sensortechnics.com Ten-X® 10 mm switching soleniod valve OUTLINE DRAWING AND MANIFOLD MOUNT DIAGRAM 6 psi devices 1.139 (28.93) 0.020 (0.5) sq. pins 0.077 (1.96) 0.575 0.375 (14.61) (9.53) Long pin Short pin 0.475 (12.07) 0.170 (4.32) Normally open port Common port Normally closed port 0.148 (3.75) Ø 0.120 (3.05) 0.030 (0.76) for use with wire hold down for PCB mounting Barb fittings for 0.078 (1.98) I.D. polyurethane tubing Ø 0.093 (2.36) 0.976 (24.79) 0.212 (5.38) 2-56 UNC-2B 0.766 (19.46) dimensions in inches (mm) 0.871 (22.12) 0.197 (5.0) 0.394 (10.01) 0.394 (10.01) 0.390 (9.91) 0.195 (4.95) 0.174 (4.42) 0.236 (6.00) Feature for 2-56 screw for valve mounting 0.870 (22.10) 0.766 (19.46) 0.976 (24.79) 0.207 (5.26) 1.25 (31.78) Ø 0.090 Ø 0.132 ±0.001 x 0.180 Ø 0.154 ±0.003 x 0.055 ±0.002 c'drill 40° to Ø 0.132 (Ø 2.29 Ø 3.35 ±0.025 x 4.57 Ø 3.91 ±0.076 x 1.4 ±0.05 c'drill 40° to Ø 3.35) 20 psi and 30 psi devices with electronics 1.303 (33.10) 0.025 (0.64) sq. pins 1.174 (29.81) 0.212 (5.38) 0.100 (2.54) 0.361 (9.17) 0.619 (15.72) Normally open port Common port Normally closed port 0.170 (4.32) Ø 0.120 (3.05) 0.035 (0.89) Ø 0.093 (2.36) 0.976 (24.79) 0.267 (6.78) 0.766 (19.46) 2-56 UNC-2B 0.871 (22.12) Feature for 2-56 screw for valve mounting 0.870 (22.10) 0.262 (6.65) 0.197 (5.0) 0.394 (10.01) 0.394 (10.01) 0.390 (9.91) 0.195 (4.95) E / 11260 / A dimensions in inches (mm) Barb fittings for 0.078 I.D. polyurethane tubing 0.766 (19.46) 0.976 (24.79) Ø 0.090 Ø 0.132 ±0.001 x 0.180 Ø 0.154 ±0.003 x 0.055 ±0.002 c'drill 40° to Ø 0.132 (Ø 2.29 Ø 3.35 ±0.025 x 4.57 Ø 3.91 ±0.076 x 1.4 ±0.05 c'drill 40° to Ø 3.35) 3/4 www.sensortechnics.com Ten-X® 10 mm switching soleniod valve ORDERING INFORMATION 6 psi devices Series Options 914 Elastomer 1 Silicone 2 Type 1* 2/3 way, NO, 6 psi Viton (FKM) 2** 2/3 way, NC, 6 psi Model 1 Standard (without electronics) 6** Distributor, 6 psi Voltage 05 5 VDC 12 12 V D C Electical 1 Short pins 2 914 1 1 000 none Long pins 24 24 V D C * Silicone elastomer only ** Viton (FKM) elastomer only Example: Accessories* * please order separately 1 05 1 000 20 psi and 30 psi devices with electronics Series Options 914 Elastomer 2 Type Viton (FKM) 3* 2/3 way, NC, 30 psi Model 2 Integrated electronics Voltage 05 5 VDC 4** 2/3 way, NO, 30 psi 12 12 V D C 5** Distributor, 20 psi 24 24 V D C Electical 3 Pins (2.54 mm) * Silicone elastomer only ** Viton (FKM) elastomer only Example: 914 2 3 Accessories* 000 none * please order separately 2 05 3 000 Note: Not all combinations might be available. Please contact your nearest Sensortechnics sales representative for further information. Accessories (please order separately using the following order numbers) Order No. Description 191-000112-010 (free of charge) Mounting screws for 6 psi devices (2 screws per valve) 191-000112-012 (free of charge) Mounting screw for 20 psi and 30 psi devices (2 screws per valve) 195-000211-001 (free of charge) Manifold gasket (FKM) for 6 psi devices (1 gasket per valve) 195-000242-001 (free of charge) Manifold gasket (FKM) for 20 psi and 30 psi devices (1 gasket per valve) 590-000073-001 (extra charge) 18 " leads w/ connector (only for devices with integrated electronics) Sensortechnics reserves the right to make changes to any products herein. Sensortechnics does not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. E / 11260 / A 4/4 www.sensortechnics.com