CONVERSION SHEET INTERNATIONAL A+ & M-SERIES LINEAR MODELS The modifications to standard models as defined in this document are identified by replacing the “-A” or “-A+” part of the model number by the appropriate dash number. Example: HB5-3/OVP-A+ becomes HB5-3/OVP-001; MC12-3.4-A becomes MC123.4-502. The marking on the chassis silkscreen is not changed. A label with the appropriate dash numbers is added in the location described below. MODELS WITH -0XX SUFFIX -00X = NO INPUT JUMPERS ON TRANSFORMER DASH NO. DESCRIPTION -001 0.375" Terminal Block Output Connector. See model specific BOM for number of terminals. -002 OVP12 or OVP24 set as listed below (single output models only) 12V = 13.8 ±0.8V 15V = 17.0 ±1.0V 24V = 27.0 ±1.0V 28V = 31.0 ±1.0V -003 Adjustable 9-15V or 12-15V output set to 12V. Use appropriate ATE program. -004 Split type lockwashers installed on TO-3 transistors. -005 Combination of -001 and -003. Use instructions for -001 AND -003 above. Install sense jumpers for 5V output. -006 Seal all voltage and current adjust pots. MODELS WITH -5XX SUFFIX -50X = INPUT JUMPERS SET FOR 120V OPERATION DASH NO. DESCRIPTION -500 Jumper pins 1 to 3 and 2 to 4 on transformer using 20GA buss wire. Apply AC input to terminals 1 and 4. All modifications listed below must include the jumpers for -500 above. -501 0.375" Terminal Block Output Connector. See model specific BOM for number of terminals. -502 OVP12 or OVP24 set as listed below (single output models only) 12V = 13.8 ±0.8V 15V = 17.0 ±1.0V 24V = 27.0 ±1.0V 28V = 31.0 ±1.0V -503 Adjustable 9-15V or 12-15V output set to 12V. Use appropriate ATE program. -504 Split type lockwashers installed on TO-3 transistors. -505 Combination of -501 and -503. Use instructions for -501 AND -503 above. Install sense jumpers for 5V output. -506 Seal all voltage and current adjust pots. RECORD OF REVISIONS LTR ECN G SL POWER ELECTRONICS CORP. INC DATE 4733 DH 4/6/92 H 5666 DH 4/9/94 J 7012 DF 9/28/98 K DESCRIPTION 45067 Removed Label note Date Printed: 4/30/09 R.J. 4/17/09 6050 KING DR. BLDG. A, Ventura, CA 93033 - 805-486-4565 DRAWN DATE 1/3/94 CHECK DRAWING NO. 41-32492-0000 DATE SHT 1 OF 3 REV K MODELS WITH -6XX SUFFIX -60X = INPUT JUMPERS SET FOR 100V OPERATION DASH NO. DESCRIPTION -600 Jumper pins 1 to 3 and 2 to 4 on transformer using 20GA buss wire. Apply AC input to terminals 1 and 5. All modifications listed below must include the jumpers for -600 above. -601 0.375" Terminal Block Output Connector. See model specific BOM for number of terminals. -602 OVP12 or OVP24 set as listed below (single output models only) 12V = 13.8 ±0.8V 15V = 17.0 ±1.0V 24V = 27.0 ±1.0V 28V = 31.0 ±1.0V -603 Adjustable 9-15V or 12-15V output set to 12V. Use appropriate ATE program. -604 Split type lockwashers installed on TO-3 transistors. -605 Combination of -601 and -603. Use instructions for -601 AND -603 above. Install sense jumpers for 5V output. -606 Seal all voltage and current adjust pots. MODELS WITH -7XX SUFFIX -70X = INPUT JUMPERS SET FOR 220V OPERATION DASH NO. DESCRIPTION -700 Jumper pins 2 to 3 on transformer using 20GA buss wire. Apply AC input to terminals 1 and 5. All modifications listed below must include the jumpers for -700 above. -701 0.375" Terminal Block Output Connector. See model specific BOM for number of terminals. -702 OVP12 or OVP24 set as listed below (single output models only) 12V = 13.8 ±0.8V 15V = 17.0 ±1.0V 24V = 27.0 ±1.0V 28V = 31.0 ±1.0V -703 Adjustable 9-15V or 12-15V output set to 12V. Use appropriate ATE program. -704 Split type lockwashers installed on TO-3 transistors. -705 Combination of -701 and -703. Use instructions for -701 AND -703 above. Install sense jumpers for 5V output. -706 Seal all voltage and current adjust pots. Page 2 of 3 CONVERSION SHEET 41-32492-0000 MODELS WITH -8XX SUFFIX -80X = INPUT JUMPERS SET FOR 240V OPERATION DASH NO. DESCRIPTION -800 Jumper pins 2 to 3 on transformer using 20GA buss wire. Apply AC input to terminals 1 and 4. All modifications listed below must include the jumpers for -800 above. -801 0.375" Terminal Block Output Connector. See model specific BOM for number of terminals. -802 OVP12 or OVP24 set as listed below (single output models only) 12V = 13.8 ±0.8V 15V = 17.0 ±1.0V 24V = 27.0 ±1.0V 28V = 31.0 ±1.0V -803 Adjustable 9-15V or 12-15V output set to 12V. Use appropriate ATE program. -804 Split type lockwashers installed on TO-3 transistors. -805 Combination of -801 and -803. Use instructions for -801 AND -803 above. Install sense jumpers for 5V output. -806 Seal all voltage and current adjust pots. Page 3 of 3 CONVERSION SHEET 41-32492-0000