MIC74 2-Wire Serial I/O Expander and Fan Controller General Description Features The MIC74 is a fully programmable serial-to-parallel I/O expander compatible with the SMBus™ (system management bus) protocol. It acts as a slave on the bus, providing eight independent I/O lines. • Provides eight bits of general purpose I/O • Built-in fan speed control logic (optional) 2 • 2-wire SMBus™/I C™-compatible serial interface plus interrupt output • 2.7V to 3.6V operating voltage range • 5V-tolerant I/O • Low quiescent current: 2µA (typical) • Bit-programmable I/O options: − Input or output − Push-pull or open-drain output − Interrupt on input changes • Outputs can directly drive LEDs (10mA IOL) • Up to 8 devices per bus Each I/O bit can be individually programmed as an input or output. If programmed as an output; each I/O bit can be programmed as an open-drain or complementary push-pull output. If desired, the four most significant I/O bits can be programmed to implement fan speed control. An internal clock generator and state machine eliminate the overhead generally associated with “bit-banging” fan speed control. Programming the device and reading/writing the I/O bits is accomplished using seven internal registers. All registers can be read by the host. Output bits are capable of directly driving high-current loads, such as LEDs. A separate interrupt output can notify the host of state changes on the input bits without requiring the MIC74 to perform a transaction on the serial bus or be polled by the host. Three address selection inputs are provided, allowing up to eight devices to share the same bus and provide a total of 64 bits of I/O. The MIC74 is available in an ultra-small-footprint 16-pin QSOP. Low quiescent current, small footprint, and low package height make the MIC74 ideal for portable and desktop applications. Applications • • • • • General purpose I/O expansion via serial bus Personal computer system management Distributed sensing and control Microcontroller I/O expansion Fan control Datasheets and support documentation are available on Micrel’s web site at: www.micrel.com. Typical Application SMBus is a trademark of Intel Corporation. I2C is a trademark of Phillips Electronics N.V. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com September 30, 2014 Revision 3.0 Micrel, Inc. MIC74 Ordering Information Part Number MIC74YQS Junction Temperature Range Package Lead Finish –40°C to +85°C 16-Pin QSOP Pb-Free Pin Configuration 16-Pin QSOP (QS) (Top View) Pin Description Pin Number Pin Name Pin Function 1, 2, 3 A0, A1, A2 Address (input): Slave address selection inputs; sets the three least significant bits of the MIC74’s slave address. 4, 5, 6, 7 P0, P1, P2, P3 8 GND 9, 10, 11, 12 P4, P5, P6, P7 (/SHDN, /FS0 /FS1, /FS2) 13 /ALERT 14 CLK 15 DATA Serial data (input/output): Serial data input and open-drain serial data output. 16 VDD Power supply (input). September 30, 2014 Parallel I/O (input/output): General-purpose I/O pin. Direction and output type are userprogrammable. Ground Parallel I/O (input/output): P4–P7 are general-purpose I/O pins. Direction and output type are user-programmable. Shutdown (output): When the FAN bit is set, pin 9 becomes SHDN. Fan speed (output): When the FAN bit is set, pins 10 through 12 become /FS0 – /FS2 respectively, controlled by the FAN_SPEED register. Interrupt (output): Active-low, open-drain output signals input-change-interrupts to the host on this pin. Signal is cleared when the bus master (host) polls the ARA (alert response address = 0001 100) or reads status. Serial bus clock (input): The host provides the serial bit clock in this input. 2 Revision 3.0 Micrel, Inc. MIC74 Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VDD) ................................................... +4.6V Input Voltage [all pins except VDD and GND] (VIN). .................................. GND – 0.3V to +5.5V Junction Temperature (TJ) ......................................... 150°C Lead Temperature (soldering, 10s) ............................ 260°C (3) ESD Rating VDD ...................................................................... 1.5kV A0, A1, A2 .............................................................. 500V Others .................................................................... 200V Supply Voltage (VDD) .................................... +2.7V to +3.6V Ambient Temperature (TA) .......................... –40°C to +85°C Package Thermal Resistance (θJA) ........................ 163°C/W Electrical Characteristics(4) 2.7V ≤ VDD ≤ 3.6V; TA = 25°C, bold values indicate –40°C < TA < +85°C, unless noted. Symbol Parameter Condition Min. VIN Input Voltage (any pin except VDD and GND) IDD Operating Supply Current P[7:0] inputs; P[7:0] = VDD or GND /ALERT open; fCLK = 100kHz ISTART Fan Startup Supply Current (Fan Mode Only) during tSTART; /ALERT, /SHDN, /FS2[2:0] = open; VCLK = VDATA = VDD; P[3:0] = inputs ISTBY Standby Supply Current /ALERT = open, VCLK = VDATA = VDD; P[3:0] = inputs Typ. GND–0.3 2 1 Max. Units 5.5 V 6 µA 1.75 mA 3 µA Serial I/O (DATA, CLK) VIL Input Low Voltage –0.3 0.8 V VIH Input High Voltage 2 5.5 V VOL Output Low Voltage IOL = 3mA 0.4 V ILEAK Leakage Current VIN = 5.5V or GND +1 µA CIN Input Capacitance –1 10 pF Notes: 1. Exceeding the absolute maximum ratings may damage the device. 2. The device is not guaranteed to function outside its operating ratings. 3. Devices are ESD sensitive. Handling precautions are recommended. Human body model, 1.5kΩ in series with 100pF. 4. Specification for packaged product only. 5. Devices participating in a transfer will timeout when any clock low exceeds the value of tTIMEOUT(min) of 25ms. Devices that have detected a timeout condition must reset the communication no later than tTIMEOUT(max) of 35ms. The maximum value specified must be adhered to by both a master and a slave as it incorporates the cumulative stretch limit for both a master (10ms) and a slave (25ms). 6. tHIGH(max) provides a simple guaranteed method for devices to detect bus idle conditions. 7. Rise and fall time is defined as follows: tR = VIL(max) – 0.15V to VIH(min) + 0.15V; tF = 0.9VDD to VIL(max) – 0.15V. 8. Guaranteed by design. September 30, 2014 3 Revision 3.0 Micrel, Inc. MIC74 Electrical Characteristics(4) (Continued) Parallel I/O [P0–P3, P4(/SHDN), P5(/FS0)–P7(/FS2)] Symbol Parameter VIL Input Low Voltage VIH Input High Voltage IOL Output Low Current IOH Condition Min. Typ. Max. Units –0.5 0.8 V 2 5.5 V VOL = 0.4V, VDD = 2.7V 7 mA VOL = 1V, VDD = 3.3V 10 mA Output High Current VOH = 2.4V 7 mA ILEAK Leakage Current VIN = 5.5V or GND –1 CIN Input Capacitance 10 pF COUT Output Capacitance 10 pF +1 µA Address Input (A0–A2) VIL Input Low Voltage –0.3 0.3VDD V VIH Input High Voltage 0.7VDD VDD+0.3 V ILEAK Leakage Current VIN = VDD or GND –250 +250 nA VOL Output Low Voltage IOL = 1mA 0.4 V ILEAK Leakage Current VIN = VDD or VSS –1 ±250 +1 µA 1 3.3 sec /ALERT AC Characteristics tSTART Fan Startup Interval Normal operation 0.5 tPULSE Minimum Pulse-Width Minimum pulse-width on Pn to generate an interrupt, Note 8 10 t/INT Interrupt Delay Interrupt delay from state change on Pn to /ALERT ≤ VOL, Note 8 t/IR Delay from Status Read or ARA Response to /ALERT ≥ VOH tHD:STA Hold Time, Note 8 Hold time after repeated start condition, after this period, the first clock is generated tSU:STA Setup Time, Note 8 Repeated start condition setup time tSU:STO Stop Condition Setup Time tHD:DAT ns 4 µs 4 µs 4 µs 4.7 µs Note 8 4 µs Data Hold Time Note 8 500 ns tSU:DAT Data Setup Time Note 8 0 ns tTIMEOUT Clock Low Time-Out Note 5, 8 25 tLOW Clock Low Period Note 6, 8 4.7 tHIGH Clock High Period Note 6, 8 4 tF Clock/Data Fall Time tR tBUF 35 ms µs 50 µs Note 7, 8 300 ns Clock/Data Rise Time Note 7, 8 1000 ns Bus free time between stop and Start condition Note 8 September 30, 2014 4.7 4 µs Revision 3.0 Micrel, Inc. MIC74 Timing Definitions Register Descriptions Table 1. Device Configuration Register DEV_CFG D[7] D[6] D[5] D[4] D[3] D[2] Always write as zero D[1] D[0] FAN IE Device Configuration Register Parameters • Power-on default value: 0000 0000b, 00h • Operation: 1 = enabled; 0 = disabled − Interrupts disabled • Bit name: FAN − Not in fan mode • Function: Selects fan mode (P[7:4] vs. /FS[2:0], /SHDN) • Operation: 1 = fan mode; 0 = I/O mode • Bit Name: D[2] through D[6] • Function: Reserved • Operation: Reserved; always write as zero • Command_byte address: 0000 0000b, 00h • Type: 8-bits, read/write • Bit name: IE • Function: Global interrupt enable Table 2. Data Direction Register DIR D[7] D[6] D[5] D[4] D[3] D[2] D[1] D[0] DIR7 DIR6 DIR5 DIR4 DIR3 DIR2 DIR1 DIR0 Data Direction Register Parameters • • Power-on default value: 0000 0000b, 00h − All Pn’s configured as inputs • Command_byte address: 0000 0001b, 01h • Type: 8-bits, read/write • Bit name: DIRn • Function: Selects data direction, input or output, of Pn • Operation: 1 = output; 0 = input Notes: If the FAN bit of the DEV_CFG register is set to ‘1’ (i.e., if fan mode is selected), P[7:4] are automatically configured as open-drain outputs. They are then referred to as /FS[2:0] and /SHDN. The DIR register has no effect on these I/O bits while in fan mode. • September 30, 2014 5 Revision 3.0 Micrel, Inc. MIC74 Register Descriptions (Continued) Table 3. Output Configuration Register OUT_CFG D[7] D[6] D[5] D[4] D[3] D[2] D[1] D[0] OUT7 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 OUT0 Output Configuration Register Parameters • Power-on default value: 0000 0000b, 00h • Operation: 1 = push-pull; 0 = open-drain − • Notes: If the FAN bit of the DEV_CFG register is set to ‘1’ (i.e., if fan mode is selected), P[7:4] are automatically configured as open-drain outputs. They are then referred to as /FS[2:0] and /SHDN. The OUT_CFG register has no effect on these I/O bits while in fan mode. All outputs open-drain • Command_byte address: 0000 0010b, 02h • Type: 8-bits, read/write • Bit name: OUTn • Function: Selects output driver configuration of Pn when Pn is configured as an output. Table 4. Status Register STATUS D[7] D[6] D[5] D[4] D[3] D[2] D[1] D[0] S7 S6 S5 S4 S3 S2 S1 S0 Status Register Parameters • Power-on default value: 0000 0000b, 00h − • Operation: 1 = change occurred; 0 = no change occurred • Notes: If the FAN bit of the DEV_CFG register is set to ‘1’ (i.e., if fan mode is selected), P[7:4] are automatically configured as open-drain outputs. They are then referred to as /FS[2:0] and /SHDN. No interrupts of any kind are generated by these pins while in fan mode. All status bits are cleared after any read operation is performed on STATUS. No interrupts pending • Command_byte address: 0000 0011b, 03h • Type: 8-bits, read/write • Bit name: Sn • Function: Flag for Pn input-change event when Pn is configured as an input. Sn is set when the corresponding input changes state. Table 5. Interrupt Mask Register INT_MASK D[7] D[6] D[5] D[4] D[3] D[2] D[1] D[0] IM7 IM6 IM5 IM4 IM3 IM2 IM1 IM0 Interrupt Mask Register Parameters • Power-on default value: 0000 0000b, 00h • Operation: 1 = enabled; 0 = disabled • Command_byte address: 0000 0100b, 04h • • Type: 8-bits, read/write • Bit name: Imn • Function: Interrupt enable bit for Pn when Pn is configured as an input. Notes: If the FAN bit of the DEV_CFG register is set to ‘1’ (i.e., if fan mode is selected), P[7:4] are automatically configured as open-drain outputs. They are then referred to as /FS[2:0] and /SHDN. No interrupts of any kind are generated by these pins while in fan mode. September 30, 2014 6 Revision 3.0 Micrel, Inc. MIC74 Register Descriptions (Continued) Table 6. Data Register DATA D[7] D[6] D[5] D[4] D[3] D[2] D[1] D[0] P7 P6 P5 P4 P3 P2 P1 P0 Data Register Parameters • Power-on default value: 1111 1111b, FFh • Read operation: 1 = Pn is high; 0 = Pn is low • Command_byte address: 0000 0101b, 05h • Write operation: 1 = Pn is set to ‘1’; 0 = Pn is cleared • Type: 8-bits, read/write • • Bit name: Pn • Function: Returns the current state of any Pn configured as an input and the last value written to Pn’s configured as outputs. Writing the DATA register sets the output state of any Pn’s configured as outputs; writes to I/O bits configured as inputs are ignored. Notes: If the FAN bit of the DEV_CFG register is set to ‘1’ (i.e., if fan mode is selected), P[7:4] are automatically configured as open-drain outputs. They are then referred to as /FS[2:0] and /SHDN. The state of these pins is determined by the FAN_SPEED register. While in fan mode, D[7:4] of the DATA registers have no effect. Table 7. Fan Speed Register FAN_SPEED D[7] D[6] D[5] D[4] D[3] D[2] Always write as zero D[1] D[0] Fan Speed Fan Speed Register Parameters • Power-on default value: 0000 0000b, 00h − • Notes: Any time the fan speed register contains zero, meaning the fan is shut down, and a non-zero value is written into the fan speed register, the /FS[2:0] and /SHDN outputs will assume the highest fan speed state for approximately one second (tSTART). Following this interval, the state of the fan speed control outputs will assume the value indicated by the contents of FAN_SPEED. This insures that the fan will start reliably when low speed operation is desired. Fan off • Command_byte address: 0000 0110b, 06h • Type: 8-bits, read/write • Bit name: D[0] through D[2] • Function: Determines bit-pattern on FS[2:0] • Operation: Fan speed settings (see below) • Bit Name: D[3] through D[7] Fan Speed • Function: Reserved 0 Off • Operation: Always write as zero 110 1 Speed 1 (slowest) 010 101 1 Speed 2 011 100 1 Speed 3 100 011 1 Speed 4 101 010 1 Speed 5 110 001 1 Speed 6 111 000 1 Speed 7 (fastest) Output State D[2:0] Value /FS[2:0] /SHDN 000 111 001 September 30, 2014 7 Revision 3.0 Micrel, Inc. MIC74 Functional Diagram Typical I/O Port (Fan Speed Control Logic Not Shown) address. The three address pins allow eight unique MIC74 addresses in a system. When the MIC74’s address matches an address received in the serial bit stream, communication is initiated. Functional Description Pin Descriptions VDD Power supply input connection. See Operating Ratings section for additional information. A2, A1 and A0 should be connected to GND or VDD. The state of these pins is sampled only once at device poweron. New slave addresses are not accepted unless the MIC74 is powered off then on. GND Ground or return connection for all MIC74 functions. CLK A CLK signal is provided by the host (master) and is common to all devices on the bus. The CLK signal controls all transactions in both directions on the bus and is applied to each MIC74 at the CLK pin. Table 8. MIC74 Address Configuration Inputs DATA Serial data is bidirectional and is common to all devices on the bus. The MIC74’s DATA output is open-drain. The DATA line requires one external pull-up resistor or current source per system that can be located anywhere along the line. A2, A1, A0 The MIC74 responds to its own unique address which is assigned using the A0–A2 pins. A0–A2 set the three LSBs (least significant bits) of the MIC74’s 7-bit slave September 30, 2014 8 MIC74 Slave Address A2 A1 A0 Binary Hex 0 0 0 010 0000b 20h 0 0 1 010 0001b 21h 0 1 0 010 0010b 22h 0 1 1 010 0011b 23h 1 0 0 010 0100b 24h 1 0 1 010 0101b 25h 1 1 0 010 0110b 26h 1 1 1 010 0111b 27h Revision 3.0 Micrel, Inc. MIC74 Alert Response Address The MIC74 also responds to the Alert Response Address (ARA). The ARA is used by the master (host) to request the address of a slave that has provided an interrupt to the master via the /ALERT line. The Read_Byte operation is a composite read-write operation consisting of first sending the MIC74’s slave address followed by a command byte (a write) and then resending the slave address and clocking out the data byte (a read). The command byte is the address of the target register. See Table 9. An example of a Read_Byte operation is shown in Figure 8. The ARA is a single address (0001 100) common to all slaves and is described in more detail under Interrupt Generation with related information under /ALERT. Also see Figure 7. Similarly, the write-byte operation consists of sending the device’s slave address followed by a command byte and the byte to be written to the target register. Again, in the case of the MIC74, the command byte is the address of the target register. See Table 9. Pn, /SHDN, and /FS0 - /FS2 P0 through P7 are general-purpose input/output bits. Each bit is independently programmable as an input or an output. If programmed as an output, each bit is further programmable as either a complementary push-pull or open-drain output. In addition, to the read byte and write byte protocols, the MIC74 adheres to the SMBus protocol for response to the ARA (alert response address). An MIC74 expects to be interrogated using the ARA when it has asserted its /ALERT output. /ALERT interrupts can be enabled or disabled using the IE bit in the DEV_CFG register. If properly enabled, any Pn programmed as an input will generate an interrupt to the host using the /ALERT output when the input changes state. In this way, the MIC74 can notify the host of an input change without requiring periodic polling by the host or a message transaction on the bus. Power-On When power is initially applied, the MIC74’s internal registers will assume their power-up default state and the state of the address inputs, A2, A1 and A0, will be read to establish the device’s slave address. See the individual register descriptions for each registers default state. Also see Table 9. Regardless of whether interrupts are enabled or disabled, each input-change event also sets the corresponding bit in the status register. I/O configuration is performed using the output configuration (OUT_CFG), I/O direction (DIR), and interrupt mask (INT_MASK) registers. I/O Ports Each I/O bit, P0 through P7, may be individually programmed as an input or output using the corresponding bit in the I/O direction register, DIR. If programmed as an output, each is further programmable as either a complementary push-pull or open-drain output using the output configuration register, OUT_CFG. If the FAN bit in the device configuration register is set, the states of P[7:4] are controlled by the FAN_SPEED register. The bits in the OUT_CFG, DIR, and INT_MASK registers corresponding to P[7:4] are ignored. When in fan mode, P[7:4] are referred to as /FS2, /FS1, /FS0, and /SHDN. While in this mode, no interrupts of any kind will be generated by these pins. If enabled by the corresponding bit, IMn, in the interrupt mask register INT_MASK, each Pn programmed as an input will generate an interrupt to the host on /ALERT if the input changes state. In this way, the MIC74 can notify the host of an input change without requiring periodic polling by the host or a transaction on the bus. /ALERT The alert signal is an open-drain, active-low output. The operation of the /ALERT output is controlled by the IMn bits in the INT_MASK register and the global interrupt enable bit (IE) in the DEV_CFG register. Each input-change event also sets the corresponding bit in the status register, STATUS. See “Functional Diagram” for the logic arrangement of atypical MIC74 I/O port. If the IE bit is set to zero, or if the corresponding interrupt enable bit, IMn, is set to zero, no input-change interrupts will be generated. Regardless of the IE bit setting, the change will be reflected in the status register. Fan Speed Control If the FAN bit in the device configuration register is set, the state of P[7:4] is controlled by the FAN_SPEED register. The bits in the OUT_CFG, DIR, and INT_MASK registers corresponding to P[7:4] are ignored. When in Fan Control Mode, P[7:4] are referred to as /FS2, /FS1, /FS0, and /SHDN. While in this mode, no interrupts of any kind will be generated by these pins. See “Application Information” for typical fan speed control applications. If the IE bit is set to one, IMn is set to one, and Pn is an input, then /ALERT is driven active whenever Pn changes state, (goes from a high-to-low or low-to-high state). Once triggered, /ALERT is unconditionally reset to its inactive state once the MIC74 successfully responds to the alert response addressor STATUS is read. Serial Port Operation The MIC74 uses standard SMBus Read_Byte and Write_Byte operations to communicate with its host. September 30, 2014 9 Revision 3.0 Micrel, Inc. MIC74 Table 9. Register Summary Address Register Name Register Description Binary DEV_CFG Device configuration DIR Power-On Default Hex Available Options Binary Hex 0000 0000b 00h 8-bit read/write 0000 0000b 00h I/O direction 0000 0001b 01h 8-bit read/write 0000 0000b 00h OUT_CFG Output configuration 0000 0010b 02h 8-bit read/write 0000 0000b 00h STATUS Interrupt status 0000 0011b 03h 8-bit read 0000 0000b 00h INT_MASK Interrupt mask 0000 0100b 04h 8-bit read/write 0000 0000b 00h DATA General purpose I/O 0000 0101b 05h 8-bit read/write 1111 1111b FFh FAN_SPEED Fan speed 0000 0110b 06h 8-bit read/write 0000 0000b 00h Fan Start-Up Any time the fan speed register contains zero (fan is off) and then a nonzero value is written to FAN_SPEED, the /FS[2:0] and /SHDN outputs will assume the highest fan speed state for approximately one second (tSTART). Following this interval, the state of the fan speed control outputs will assume the value indicated by the contents of FAN_SPEED. This insures that the fan will start reliably when low speed operation is desired. The tSTART interval is generated by an internal oscillator and counters. At the end of tSTART, this oscillator is powered down to reduce overall power consumption. when the fan is shutdown (zero is written to FAN_SPEED), the /SHDN pin is deasserted first. The /FS[2:0] lines are subsequently deasserted after a delay of 1⁄2tSTART. The internal oscillator is also powered down following the tSTART/2 interval at fan shut-down. These timing relationships are illustrated in Figure 2. Interrupt Generation Assuming that any or all of the I/Os are configured as inputs, the MIC74 will reflect the occurrence of an input change in the corresponding bit in the status register, STATUS. This action cannot be masked. An input change will only generate an interrupt to the host if interrupts are properly configured and enabled. The MIC74 can operate in either polled mode or interrupt mode. In the case of polled operation, the host periodically reads the contents of STATUS to determine the device state. The act of reading STATUS clears its contents. Repeating events which have occurred since the last read from STATUS will not be discernable to the host. Interrupts are only generated if the global interrupt enable bit, IE, in the DEV_CFG register is set. The /ALERT signal will be asserted (driven low) when an interrupt is generated. The MIC74 expects to be interrogated using the ARA when it has generated an interrupt output. Once it has successfully responded to the ARA (Alert Response Address), the /ALERT output will be deasserted. The contents of the status register will not be cleared until it is read using a read byte operation. If a given system does not wish to use the SMBus ARA protocol for reporting interrupts, the system may simply poll the contents of the status register after detecting an interrupt on /ALERT. This action will clear the contents of STATUS and cause /ALERT to be deasserted. Reading the status register is an acceptable substitute for using the ARA protocol. Presumably, however, it will involve higher system overhead since all the devices on the bus must be polled to determine which one generated the interrupt. Figure 1. Fan Speed Control Application Proper sequencing of the /FS[2:0] and /SHDN signals is performed by the MIC74’s internal logic state machine. When activating the fan from the off state, the /FS[2:0] lines change state first, then, after a delay equal to onehalf of tSTART, the /SHDN pin is deasserted. Conversely, September 30, 2014 10 Revision 3.0 Micrel, Inc. MIC74 Figure 2. Typical MIC74 Fan Mode Timing and System Behavior September 30, 2014 11 Revision 3.0 Micrel, Inc. MIC74 Application Information Bit Transfer The data received on the DATA pin must be stable during the high period of the clock. Figure 4. Start and Stop Definitions Start (leading edge of start) and stop (trailing edge of stop) conditions are always generated by the bus master (host). After a start condition, the bus is considered to be busy. The bus becomes free again after a certain time following a stop condition or after both CLK and DATA lines remain high for more than 50µs. Figure 3. Acceptable Bit Transfer Conditions Data can change state only when the CLK line is low. Refer to the figure above. Serial Byte Format Every byte consists of 8 bits. Each byte transferred on the bus must be followed by an acknowledge bit. Bytes are transferred with the MSB (most significant bit) first. See Figure 5. Start and Stop Conditions Two unique bus situations define start and stop conditions. A high-to-low transition of the DATA line while CLK is high indicates a start condition. A low-to-high transition of the DATA line while CLK is high defines a stop condition. See Figure 4. Figure 5. Serial Byte Format Acknowledge and Not Acknowledge The acknowledge related clock pulse is generated by the master. The transmitter releases the DATA line (high) during the acknowledge clock cycle. In order to acknowledge (ACK) a byte, the receiver must pull the DATA line low during the high period of the clock pulse according the bus timing specifications. A slave device that wishes to not acknowledge a byte must let the DATA line remain high during the acknowledge clock pulse. See Figure 6. Figure 6. Acknowledge and Not Acknowledge September 30, 2014 12 Revision 3.0 Micrel, Inc. MIC74 Figure 7. Interrupt Handling Using the Alert Response Address Figure 8. Interrupt Handling Without the Alert Response Address September 30, 2014 13 Revision 3.0 Micrel, Inc. MIC74 Initializing the MIC74 The MIC74’s internal registers are reset to their default state at power-on. The MIC74’s default state can be summarized as follows: • All I/Os configured as inputs (DIR = 00h) • Output configuration set to open-drain (OUT_CFG = 00h) • All outputs high/floating (DATA = FFh) • Fan functions disabled (FAN_SPEED = 00h; FAN bit of DEV_CFG = 0) • All interrupts masked (IE bit of DEV_CFG = 0) 1. Write DATA 2. Write OUT_CFG 3. Write DIR 4. Write FAN_SPEED (if using fan mode) 5. Write INT_MASK (if using interrupts) 6. Read STATUS to clear it 7. Write DEV_CFG to enable fan mode and/or interrupts, if using. At the conclusion of step three, any I/Os configured as outputs in step 2 will be driven to the levels programmed into the data register in step one. The order of step 1 through step 3 is important to ensure that spurious data does not appear at the I/Os during configuration. Following step 7, programming the device configuration register, the MIC74 will begin generating interrupts if they are enabled, and the fan will be started if FAN_SPEED contains a nonzero value. The corresponding interrupt service routines (if any) must be initialized and enabled prior to step 7. STATUS should be cleared (step 6) in both polled and interrupt driven systems. The result of this configuration is that all I/O pins will essentially float unless driven by external circuitry. Any system using the MIC74 will need to initialize the internal registers to the state required for proper system operation. The recommended order for initializing the MIC74’s registers is as follows: Figure 9. Initializing the MIC74 for Polled Operation Figure 10. Initializing the MIC74 for Interrupts September 30, 2014 14 Revision 3.0 Micrel, Inc. MIC74 Polled Mode Input state changes on I/Os configured as inputs will be reflected in the status register regardless of the state of the global interrupt enable bit (IE) and the individual interrupt mask bits in INT_MASK. In a system utilizing polling to monitor for input changes, the status register is periodically read to check for input events. The act of reading STATUS clears it in preparation for detecting future events. The status bits corresponding to I/Os configured as outputs or corresponding to P[7:4] when in fan mode will not be set by state changes on these pins. It is always good practice, however, to mask the value obtained when reading STATUS to eliminate any bits, output or otherwise, that are not of immediate concern. This will help avoid problems if software changes are made in the future. Interrupt Mode Input state changes on I/Os configured as inputs will be reflected in the status register regardless of the state of the global interrupt enable bit (IE) and the individual interrupt mask bits in INT_MASK. In a system utilizing interrupts to detect input changes, one or more of the bits in the interrupt mask register, INT_MASK, are set to allow interrupts on /ALERT to be generated by input events. The global interrupt enable bit, IE, in the device configuration register must also be set to enable interrupts. The flowchart shown in Figure 10 illustrates the steps involved in initializing the MIC74 for interrupt-driven operation. The flowchart in Figure 12 illustrates the corresponding interrupt service routine using the SMBus ARA. The corresponding timing diagram is shown in Figure 7. The flowchart in Figure 13 illustrates the corresponding interrupt service routine using polling to determine the interrupt source. Figure 8 illustrates the timing. Utilizing the ARA greatly speeds identification of the interrupting slave device and lowers latency, as only a single transaction on the bus is necessary to identify the interrupt source. The flowchart shown in Figure 9 illustrates the steps involved in initializing the MIC74 for polled operation. The flowchart in Figure 11 illustrates the corresponding polling routine. The process for writing output data is straightforward—simply write the desired bit pattern to DATA. Special precautions may be required when changing output data in an interrupt driven system, however. See the Writing to the Data Register section. Using either method, STATUS must be read to determine the exact source of the interrupt within the MIC74. Figure 11. Polling the MIC74 September 30, 2014 15 Revision 3.0 Micrel, Inc. MIC74 Writing to the Data Register Multiple software routines may use the various output bits available on the MIC74 to control individual functions such as power switches, LEDs, etc. These various functions may be handled by independent software routines that must manipulate individual output bits without regard for other bits. Care must be taken to ensure that these various software routines do not interfere with each other when modifying output data. The recommended procedure for changing isolated output bits is as follows: The act of reading STATUS clears it in preparation for detecting future events. The status bits corresponding to I/Os configured as outputs or corresponding to P[7:4] when in fan mode will not be set by state changes on these pins. It is always good practice, however, for the interrupt service routine to mask the value obtained when reading STATUS to eliminate any bits, output or otherwise, that are not of immediate concern. This will help avoid problems if software changes are made in the future. The process for writing output data is straight-forward— simply write the desired bit pattern to DATA. Special precautions may be required, however, when changing output data in an interrupt driven system. See the Writing to the Data Register section. 1. Read DATA 2. Set desired bits by ORing the value read from DATA with an appropriate mask value 3. Clear desired bits by ANDing the value read from DATA with an appropriate mask value 4. Write the result back to DATA A functionally equivalent alternative to this procedure is to keep an image of the data register in software. Any independent routines would make changes to this image using the procedure above and then call a routine that actually writes the new image to DATA. Interrupts would be disabled briefly while DATA is being modified. Figure 12. Interrupt Service Routine Using the ARA Figure 13. Interrupt Service Routine Without ARA September 30, 2014 16 Revision 3.0 Micrel, Inc. MIC74 Regardless of which procedure is used, it is important that only one software routine at a time attempts to make changes to the output data. In a system where polling is the exclusive method for servicing inputs, this is usually not a problem. If interrupts are employed to any degree in dealing with MIC74 inputs, care must be taken to ensure that a software routine in the midst of making changes to outputs is not interrupted by another routine that proceeds to make its own changes. The risk is that the value in DATA will be changed by an interrupting routine after it is read by a different routine in the process of making its own changes. If this occurs, the value written to DATA by the first routine may be incorrect. The most straightforward solution to this potential problem is to disable system interrupts while the data register is actually being modified. Any conventional adjustable regulator is usually suitable for use with the MIC74. The output voltage corresponding to each value to be programmed into the fan speed register can be determined by selecting the resistors in the circuit. The regulator itself can be chosen to meet the needs of the application, such as input voltage, output voltage, current handling capability, maximum power dissipation, and physical space constraints. Two circuit examples are shown below. The circuit of Figure 14 illustrates use of a typical LDO linear regulator such as the MIC29152. A switching regulator-based fan control circuit using the MIC4574 200kHz simple 0.5A buck regulator is shown in Figure 15. Both circuits assume a 12V fan power supply but will accommodate much higher input voltages if required (MIC4574: 24V, MIC29152: 26V). Care must be taken, however, to ensure that the maximum power dissipation of the regulator is not exceeded. If the regulator overheats, its internal thermal shutdown circuitry will deactivate it. (See MIC29152 or MIC4574 datasheet.) Application Circuits The MIC74, in conjunction with a linear low-dropout or switching regulator, can be configured as a fan speed controller. Most adjustable regulators have a feedback pin and use an external resistor divider to adjust the output voltage. The MIC74 is designed to take advantage of this configuration with its ability to manipulate multiple feedback resistors connected to the P4–P7 outputs. Individual open-drain output bits are selectively grounded or allowed to float under the control of the internal state machine. This action raises or lowers the equivalent resistance seen in the regulator’s feedback path, thus changing the output voltage. Because the MIC74 powers up with all its I/Os inputs (floating), both circuits will power-up with the fan running at a minimum speed determined by the value of RMIN_SPEED. Once the MIC74’s fan mode is activated by setting the appropriate bit in the configuration register Figure 14. Fan Speed Control Using an Adjustable Low-Dropout Regulator Figure 15. Fan Speed Control Using a Buck Converter September 30, 2014 17 Revision 3.0 Micrel, Inc. MIC74 the fan will be shutdown by the assertion of the /SHDN output if FAN_SPEED is zero. If FAN_SPEED is programmed with any nonzero value, the fan will be driven to its maximum speed for the duration of tSTART (about 1 second) and then assume the programmed speed. Note that the circuit in Figure 15 contains an additional transistor, Q1, as an inverter because the regulator in this example has an active-high shutdown input rather than an enable input. Otherwise the circuits function identically. The following equations show how to calculate the resistor values for the fan controllers. For example, when the fan speed register contains 011b, which is the third lowest speed, RF1 and RF0 are parallel to RMIN to give the equivalence resistor (REQ) value of 545Ω. REQ = RF1 || RF0 || RMIN REQ = 1.8k || 3.6k || 1k REQ = 545Ω Table 10 lists the output voltages corresponding to all the fan speeds and system states possible with these circuits. The following equations are used to calculate the resistor values used in MIC74 fan speed control circuits. It is assumed here that the regulator’s internal reference voltage is 1.24V. If the regulator uses a different reference voltage, that value should be used instead. The output voltage is calculated by using: R VOUT = 1.24V 1 + FB R EQ 3k VOUT = 1.24V 1 + 545Ω VOUT = 8.06V Table 10. Fan Speed Selection FAN_SPEED Value Fan Speed Selected RFB RMIN RF2 RF1 RF0 REQ VOUT 0000 0000b Power-up 3k 1k Open Open Open 1k 4.96V 0000 0000b Fan off 3k 1k Open Open Open 1k 0V 0000 0001b Lowest 3k 1k Open Open 3.6k 783 5.99V 0000 0010b nd lowest 3k 1k Open 1.8k Open 643 7.03V 0000 0011b 3 lowest 3k 1k Open 1.8k 3.6k 545 8.06V 0000 0100b Medium 3k 1k 1k Open Open 500 8.68V 0000 0101b rd 3k 1k 1k Open 3.6k 439 9.71V 3k 1k 1k 1.8k Open 391 10.75V 3k 1k 1k 1.8k 3.6k 353 11.78V 0000 0110b 0000 0111b 2 rd 3 highest 2 nd highest Highest September 30, 2014 18 Revision 3.0 Micrel, Inc. MIC74 Package Information and Recommended Landing Pattern(9) 16-Pin QSOP (QS) Note: 9. Package information is correct as of the publication date. For updates and most current information, go to www.micrel.com. September 30, 2014 19 Revision 3.0 Micrel, Inc. MIC74 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel, Inc. is a leading global manufacturer of IC solutions for the worldwide high performance linear and power, LAN, and timing & communications markets. The Company’s products include advanced mixed-signal, analog & power semiconductors; high-performance communication, clock management, MEMs-based clock oscillators & crystal-less clock generators, Ethernet switches, and physical layer transceiver ICs. Company customers include leading manufacturers of enterprise, consumer, industrial, mobile, telecommunications, automotive, and computer products. Corporation headquarters and state-of-the-art wafer fabrication facilities are located in San Jose, CA, with regional sales and support offices and advanced technology design centers situated throughout the Americas, Europe, and Asia. Additionally, the Company maintains an extensive network of distributors and reps worldwide. Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this datasheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2000 Micrel, Incorporated. September 30, 2014 20 Revision 3.0