XV-Z21000

OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
BRUKSANVISNING
MANUAL DE MANEJO
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
DEUTSCH
XV-Z21000
PROJECTOR
PROJEKTOR
PROJECTEUR
PROJEKTOR
PROYECTOR
PROIETTORE
PROJECTOR
ENGLISH
XV-Z21000
FRANÇAIS
SVENSKA
ESPAÑOL
ITALIANO
NEDERLANDS
Printed in China
In China gedruckt
Imprimé en Chine
Triykt i Kina
Impreso en China
Stampato in Cina
Gedrukt in China
TINS-C542WJZZ
06P07-CH_NM
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse.
Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or
and of the
same rating as above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut
off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a
serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth
Blue
: Neutral
Brown
: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug proceed as follows:
• The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is
marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow.
• The wire which is coloured blue must be connected to the terminal which is marked with the letter N
or coloured black.
• The wire which is coloured brown must be connected to the terminal which is marked with the letter L
or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
Before using the projector, please read this operation manual carefully.
ENGLISH
Introduction
IMPORTANT
• For your assistance in reporting the loss or theft of
your Projector, please record the Serial Number located on the bottom of the projector and retain this
information.
• Before recycling the packaging, please ensure that
you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on
page 4.
WARNING:
Model No.: XV-Z21000
Serial No.:
High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain
or moisture.
See bottom of projector.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk or electric shock to
persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector enters standby mode. During normal operation, when putting the projector into standby mode always use the STANDBY button on the projector or the STANDBY button on the remote control. Ensure the cooling fan has stopped before disconnecting the
power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD.
FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
-1
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of
these materials may be regulated due to environmental considerations. For disposal or recycling information, please
contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance:
www.eiae.org.
Caution Concerning Lamp Replacement
See “Regarding the Lamp” on page 48.
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 2,073,600 pixels (micromirrors). As
with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there
are certain acceptable tolerances that the equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture
screen. This will not affect the picture quality or the life expectancy of the unit.
• The DLP® logo, the DLP® medallion and BrilliantColor™ are trademarks of Texas Instruments.
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or other
countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
• All other company or product names are trademarks or registered trademarks of their respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or
discompile the contents thereof.
-2
Preparing
Introduction
Contents ...........................................................3
Accessories .....................................................4
IMPORTANT SAFEGUARDS............................5
Part Names and Functions .............................8
Using the Remote Control ............................11
Inserting the Batteries.......................................... 11
Usable Range ..................................................... 11
Quick Start
Quick Start .....................................................12
Using
Basic Operation
Turning the Projector On/Off ........................25
Connecting the Power Cord ................................ 25
Turning the Projector On ..................................... 25
Turning the Power Off
(Putting the Projector into Standby Mode) ..... 26
Image Projection ...........................................27
Switching the Input Mode.................................... 27
Adjusting the Projected Image ............................. 27
Operating with the Remote Control.............29
Switching the Iris Setting ..................................... 29
Adjusting the Contrast ......................................... 29
Adjusting the Quantity of Light............................. 29
Freezing a Moving Image..................................... 29
Selecting the Picture Mode ................................. 29
Selecting the Screen Size .............................30
Resize Mode ....................................................... 30
Useful Features
Menu Bar Items .............................................32
Using the Menu Screen.................................34
Menu Selections (Adjustments) ........................... 34
Picture Adjustment (“Picture” Menu) ..........36
Selecting the Picture Mode ................................. 36
Adjusting the Image ............................................ 36
Selecting the Gamma Position ............................ 37
Switching the Iris Setting ..................................... 37
Lamp Setting ...................................................... 37
Using the Advanced ............................................ 37
Adjusting the Colors ............................................ 37
Adjusting the BrilliantColorTM ................................ 38
Selecting the Progressive Mode .......................... 38
Reference
Appendix
Maintenance Indicators/Maintenance.........46
Regarding the Lamp ......................................48
Lamp .................................................................. 48
Caution Concerning the Lamp............................. 48
Replacing the Lamp ............................................ 48
Removing and Installing the Lamp Unit................ 49
Resetting the Lamp Timer ................................... 50
Introduction
Contents
Setup
Setting Up the Projector ...............................14
Setting Up the Projector ...................................... 14
Standard Setup (Front Projection) ........................ 14
Projection (PRJ) Mode......................................... 15
Ceiling-mount Setup ........................................... 15
Picture (Screen) Size and Projection Distance ...... 16
Connections
Samples of Cables for Connection ..............17
Connecting to Video Equipment ..................18
Connecting to a Computer ...........................23
Controlling the Projector by a Computer ....24
Selecting the Film Mode ...................................... 38
Reducing Image Noise (DNR) .............................. 38
Mosquito Noise Reduction (MNR) ....................... 38
Adjusting the Unveil Control ................................ 39
Adjusting the Automatic Contrast ........................ 39
Resetting All Adjustment Items ............................ 39
Gamma Adjustment (“Gamma” Menu) ........40
Selecting the Gamma Position ............................ 40
Adjusting the Gamma.......................................... 40
Computer Image Adjustment (“Fine Sync” Menu) ......41
Adjusting the Computer Image ............................ 41
Special Modes Setting ........................................ 41
Checking the Input Signal.................................... 41
Auto Sync (Auto Sync Adjustment) ...................... 41
Using the “Options” Menu ............................42
Adjusting the Image Position ............................... 42
Adjusting the Vertical Size of the Display (Subtitle Setting) ..... 42
Adjusting the Overscan ....................................... 42
Adjusting the White Level/Black Level ................. 43
Turning LED Off ................................................... 43
Checking the Lamp Life Status............................ 43
Setting On-screen Display ................................... 43
Setting the Video System .................................... 43
Signal Type Setting .............................................. 44
Adjusting the Color Space ................................... 44
Adjusting the Dynamic Range ............................. 44
Selecting the Background Image ......................... 44
Adjusting the Economy Mode ............................. 44
Selecting the Transmission Speed (RS-232C) ...... 45
Fan Mode Setting ................................................ 45
Reversing/Inverting Projected Images .................. 45
Returning to the Default Settings ......................... 45
Other Function ...............................................45
Selecting the On-screen Display Language ......... 45
Wired Remote Control Terminal
Specifications...........................................59
Computer Compatibility Chart .....................60
Troubleshooting .............................................61
Specifications ................................................63
Dimensions ....................................................64
Index ...............................................................65
Connecting Pin Assignments .......................51
RS-232C Specifications and Command
Settings .....................................................52
-3
Accessories
Supplied accessories
Remote control
RRMCGA500WJSB
Two AA size batteries
Lens cap (attached)
PCAPH1056CESA
Terminal cover
GCOVAB677WJKB
21 pin RCA
conversion adaptor
QSOCZ0361CEZZ
Video cable
QCNWGA001WJZZ
For Europe, except U.K.
DVI to D-sub cable
(6' (1.8 m))
QCNWGA010WJPZ
Operation manual
Power cord*
(1)
(2)
For Europe, except U.K.
(6' (1.8 m))
QACCVA011WJPZ
For U.K. and Singapore
(6' (1.8 m))
QACCBA036WJPZ
(3)
For Australia, New Zealand and Oceania
(6' (1.8 m))
QACCLA018WJPZ
* Use the power cord that corresponds to the wall outlet in your country.
Optional accessories
■
■
■
■
Lamp unit
3 RCA to 15-pin D-sub cable (9'10" (3.0 m))
DVI to 15-pin D-sub adaptor (7.9" (20 cm))
DVI cable (9'10" (3.0 m))
AN-K20LP
AN-C3CP2
AN-A1DV
AN-C3DV
Note
• Some of the optional accessories may not be available depending on the region. Please check with your
nearest Sharp Authorized Service Center or Dealer.
Marks Used in This Operation Manual
Info
............ Indicates safeguards when using the projector.
Note ............ Indicates additional information for setting up and operating the projector.
• In this operation manual, the illustration and the screen display are simplified for explanation, and may differ
slightly from actual display.
For Future Reference
Maintenance
P. 46 and 47
-4
Troubleshooting
P. 61 and 62
Index
P. 65
Introduction
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this product and save these
instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE
HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for
its installation, use and servicing.
1. Read Instructions
All the safety and operating instructions should be read before
the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained for
future reference.
3. Heed Warnings
All warnings on the product and in the operating instructions
should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
6. Attachments
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;
or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand, tripod,
bracket, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended
by the manufacturer, or sold with the product. Any mounting
of the product should follow the manufacturer’s instructions,
and should use a mounting accessory recommended by the
manufacturer.
9. Transportation
A product and cart combination should
be moved with care. Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination
to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation
to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product
dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the
operating instructions.
12. Grounding or Polarization
This product is provided with one of the following types of plugs.
If the plug should fail to fit into the power outlet,
please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with a
grounding terminal.
This plug will only fit into a grounding type power
outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
14. Lightning
For added protection for this product during a lightning storm, or
when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the cable system.
This will prevent damage to the product due to lightning and
power-line surges.
15. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never
spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as an improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the product to normal operation.
e. If the product has been dropped or damaged in any
way.
f. When the product exhibits a distinct change in
performance, this indicates a need for service.
19. Replacement Parts
When replacement parts are required, ensure the service
technician has used replace ment parts specified by the
manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock,
or other hazards.
20. Safety Check
Upon completion of any service or repairs to this product, ask
the service technician to perform safety checks to determine
that the product is in proper operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
-5
Observe the following safeguards when setting up your projector.
Caution concerning the lamp unit
■ Potential hazard of glass particles if lamp ruptures.
In case of lamp rupture, contact your nearest Sharp
Authorized Service Center or Dealer for replacement.
See “Regarding the Lamp” on page 48.
Caution concerning the setup of the projector
■ For minimal servicing and to maintain high image quality,
SHARP recommends that this projector be installed in
an area free from humidity, dust and cigarette smoke.
When the projector is subjected to these environments,
the vents and lens must be cleaned more often. As
long as the projector is regularly cleaned, use in these
environments will not reduce the overall operation life of
the unit. Internal cleaning should only be performed by
a Sharp Authorized Service Center or Dealer.
Do not set up the projector in places exposed to
direct sunlight or bright light.
■ Position the screen so that it is not in direct sunlight or
room light. Light falling directly on the screen washes out
the colors, making viewing difficult. Close the curtains
and dim the lights when setting up the screen in a sunny
or bright room.
Caution regarding placing of the projector
■ Place the projector on a level site within the adjustment
range (±5 degrees) of the adjustment foot.
Rest your eyes occasionally.
■ Continuously watching the screen for long hours will
cause eye strain. Be sure to occasionally rest your
eyes.
Avoid locations with extremes of temperature.
■ The operating temperature of the projector is from 41°F
to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is from –4°F
to 140°F (–20°C to +60°C).
Do not block the exhaust and intake vents.
■ Allow at least 1113/16 inches (30 cm) of space between
the exhaust vent and the nearest wall or obstruction.
■ Be sure that the intake vent and the exhaust vent are not
obstructed.
■ If the cooling fan becomes obstructed, a protection
circuit will automatically put the projector into standby
mode to prevent overheat damage. This does not indicate a malfunction. (See page 46.) Remove the projector
power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust
vents are not blocked, plug the power cord back in and
turn on the projector. This will return the projector to the
normal operating condition.
■ When turning off the projector, the cooling fan runs to
decrease the internal temperature for a while. Unplug
the power cord after the cooling fan stops. The period
the cooling fan runs will vary, depending on the circumstances and the internal temperature.
Caution regarding usage of the projector
■ After the projector is purchased, a faint smell from the
vent may appear when the power is first turned on. This
is normal and is not a malfunction. It will disappear after
the projector is used for a while.
When using the projector in high-altitude areas
such as mountains (at altitudes of approximately 4,900 feet (1,500 meters) or more)
■ When you use the projector in high-altitude areas with
thin air, set “Fan Mode” to “High”. Neglecting this can
affect the longevity of the optical system.
Warning about placing the projector in a high
position
■ When placing the projector in a high position, ensure that
it is secured carefully to avoid personal injury caused by
the projector falling down.
Do not subject the projector to hard impact
and/or vibration.
■ Protect the lens so as not to hit or damage the surface
of the lens.
-6
■ When using the projector, be sure not to subject it to
hard impact and/or vibration, as this can result in damage. Take extra care with the lens. Before moving the
projector, be sure to unplug the power cord from the wall
outlet, and disconnect any other cables connected to
it.
■ Do not carry the projector by holding the lens.
■ When storing the projector, re-attach the lens cap. (See
page 8.)
■ Do not expose the projector to direct sunlight or place
next to heat sources. Doing so may affect the cabinet
color or cause deformation of the plastic cover.
Other connected equipment
■ When connecting a computer or other audio-visual
equipment to the projector, make the connections AFTER
unplugging the power cord of the projector from the AC
outlet and turning off the equipment.
■ Please read the operation manuals of the projector and
the equipment to be connected for instructions on how
to make the connections.
Using the projector in other countries
■ The power supply voltage and the shape of the plug may
vary depending on the region or country you are using
the projector in. When using the projector overseas, be
sure to use an appropriate power cord for the country
you are in.
■ If the projector starts to overheat due to setup problems
or blockage of the air vents, “
” and “
” will
illuminate in the lower left corner of the picture. If the
temperature continues to rise, the lamp will turn off, the
temperature warning indicator on the projector will blink,
and after a 90-second cooling-off period the projector
will enter standby mode. Refer to “Maintenance Indicators/Maintenance” on page 46 for details.
Introduction
Temperature monitor function
Info
• The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during
projector operation due to changes in the fan
speed. This does not indicate malfunction.
• Do not unplug the power cord during projection
or cooling fan operation. This can cause damage
due to rise in internal temperature, as the cooling
fan also stops.
-7
Part Names and Functions
Numbers in
refer to the main pages in this operation manual where the topic is explained.
Projector
MENU button
For displaying adjustment
and setting screens.
Adjustment buttons
(□, ▼, \, ●)
34
34
30
RESIZE button
27
INPUT button
26
STANDBY button
25
ON button
46
Temperature warning
indicator
For selecting menu items.
ENTER button
For setting items selected
or adjusted on the menu.
RETURN button
For undoing an operation.
Lens shift dial
For moving the projected
image vertically.
34
34
27
Focus ring
27
Adjustment foot
28
For displaying the Input
list.
For putting the projector
into the standby mode.
For turning the power on.
When the internal
temperature rises, this
indicator will illuminate red.
28
Zoom knob
For switching the screen
size (SIDE BAR, SMART
STRETCH, etc.).
25, 46
Lamp indicator
25, 46
Power indicator
Illuminates blue, indicating
normal function. Replace
the lamp when the
indicator illuminates red.
Illuminates red, when the
projector is in standby.
When the power is turned
on, this indicator will
illuminate blue.
Intake vent
Lens cap
47
28
Pressing the two tabs, you can
remove/attach the lens cap.
11
Remote control sensor
Using the Terminal Cover
When the projector is used on a desktop, high mounted
or ceiling mounted, attach the terminal cover (supplied) to
hide the connecting cables.
Attaching the Terminal Cover
1 Align the hook on the terminal cover with the insert
hole in the hook at the back of the projector.
2 Press the hook in the direction indicated with the arrow
to fasten the terminal cover to the projector.
3 Insert the terminal cover into the mounting groove on
the projector while pushing the tabs inside the terminal
cover to the outside with your fingers.
-8
Adjustment foot
PUSH!
3
3
1
2
1
Remove the rubber cap attached on the projector and attach the hooks.
Introduction
Projector (Rear View)
47
Intake vent
Intake vent
47
Kensington Security
Standard connector
Exhaust vent
47
Remote control
sensor
11
AC socket
25
Connect the supplied power cord.
Terminals
Terminal
1
2
3
4
5
6
7
8
Description
COMPONENT/RGB1, 2 terminals
Connecting video equipment with component output terminal (DVD player, etc.) or a computer with analog RGB output terminal.
S-VIDEO terminal
Connecting video equipment with S-video output terminal (DVD player, VCR, etc.).
VIDEO terminal
Connecting video equipment without S-video output terminal.
DVI terminal
Connecting video equipment with DVI output terminal (DVD player, DTV decoder, computer,
etc.).
HDMI1, 2 terminals
Connecting video equipment with HDMI output terminal.
RS-232C terminal
Connecting a computer to control the projector.
TRIGGER terminal
When the projector is turned on, a control signal (DC 12V) outputs from this terminal. If an
electric screen or other compatible device is connected, it can be turned on when the projector
is turned on.
WIRED REMOTE control input terminal
Connecting the remote control via a cable when the projector is placed out of the reach of
remote control signals.
Page
20, 21
22
22
18-20, 23
18
24
—
10
Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System.
Refer to the information that came with the system for instructions on how to use it to secure the projector.
-9
Part Names and Functions (Continued)
Numbers in
refer to the main pages in this operation manual where the topic is explained.
Remote Control
Remote control signal
transmitters
11
STANDBY button
26
For putting the projector into the
standby mode.
ENTER button
For setting items selected or
adjusted on the menu.
RETURN button
For undoing an operation.
AUTO SYNC button
For automatically adjusting images
when connected to a computer.
RESIZE button
For switching the screen size
(SIDE BAR, SMART STRETCH,
etc.).
RGB/COMP. button
For switching to the respective
input signal type.
IRIS button
WIRED R/C JACK
For controlling the projector by
connecting the remote control to
the projector.
34
34
For displaying the Input list.
ON button
34
MENU button
34
Adjustment buttons
(", ', \, |)
For turning the power on.
For displaying adjustment and
setting screens.
For selecting menu items.
27
Input Mode Select buttons
29
PICTURE MODE button
29
CONTRAST button
29
FREEZE button
29
BRIGHT button
41
30
44
29
For switching “HIGH
BRIGHTNESS MODE”, “MEDIUM
MODE” and “HIGH CONTRAST
MODE”.
INPUT button
25
For switching to the respective
input modes.
For selecting the appropriate
picture to best match the projected
image.
For displaying the contrast
adjustment screen.
For freezing images.
For displaying the brightness
adjustment screen.
LIGHT button
For lighting all buttons on the
remote control.
27
Connecting the Remote Control to the Projector
When the remote control cannot be used due to the range or positioning of the projector, connect a ø3.5 mm
minijack cable (commercially available) from the WIRED R/C JACK on the top of the remote control to the WIRED
REMOTE control input terminal on the rear of the projector.
To WIRED REMOTE control input terminal
To WIRED R/C JACK
ø3.5 mm minijack cable
(commercially available)
Remote control
-10
Introduction
Using the Remote Control
Inserting the Batteries
1
2
Pull down the tab on the cover
and remove the cover towards
the direction of the arrow.
Insert the supplied batteries and
put back the cover.
• Make sure the polarities correctly match
the
and
marks inside the battery
compartment.
• When putting back the cover, be sure that
the cover clicks in place and settles.
Usable Range
The remote control can be used to control
the projector within the ranges shown in the
illustration.
Remote control
signal transmitters
30°
30°
30°
Remote control sensors
Note
• The signal from the remote control can be
reflected off a screen for easy operation. However, the effective distance of the signal may
differ depending on the screen material.
When using the remote control:
• Be sure not to drop, expose to moisture or high
temperature.
• The remote control may malfunction under a
fluorescent lamp. In this case, move the projector away from the fluorescent lamp.
23' (7 m)
30°
30°
Remote control
signal transmitters
30°
23' (7 m)
Remote control
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
• Danger of explosion if bettery is incorrectly replaced.
Replace only with the same or equivalent type.
and
marks inside the battery compartment.
• Insert the batteries making sure the polarities correctly match the
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fluid from leaked batteries is harmful to skin, therefore be sure to first wipe them and then remove them using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you are not to use the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
-11
Quick Start
This section provides an example showing how to connect the projector to video equipment with a brief explanation of the steps from connection through to image projection.
For details, see the pages suggested in each step.
7 STANDBY button
3 ON button
6 Zoom knob
5 Input Mode
6 Focus ring
Select buttons
6 Adjustment feet
1. Place the projector facing a screen
Page 14
2. Connect the projector to the video equipment and plug
Pages 18-25
the power cord into the AC socket of the projector
To VIDEO terminal
AC socket
Connect the audio output terminal
of the video equipment to the audio
input terminal of the audio equipment
using an audio cable.
3. Remove the lens cap and turn the projector on
Page 25
Pointing the remote control towards the
ON button.
projector, press the
ON
-12
4. Turn the video equipment on and start playback
5. Select the input mode
Press the
Quick Start
Playback
Page 27
VIDEO button on the remote control to select “VIDEO” for the Input mode.
VIDEO
• Press
/
/
/
/
/
/
on the remote control to switch the Input mode.
6. Adjust the projector angle, focus and zoom
1. The focus is adjusted by
rotating the focus ring.
2. Zooming is adjusted by
moving the zoom knob.
Pages 27, 28
3. The projector angle is
adjusted by using the
adjustment feet. As for
adjustment of the vertical
position of the projected
image, use the lens shift dial.
Zoom knob
Lens shift dial
Focus ring
Foot releases
7. Turn the power off
Page 26
Press
STANDBY on the remote control, then press that button again while the confirmation message
is displayed, to put the projector into standby mode.
STANDBY
□ On-screen display
□
• Unplug the power cord from the AC outlet after the cooling fan stops.
-13
Setting Up the Projector
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and
level.
Note
• The projector lens should be centered in the middle of the screen. If the horizontal line passing through
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
• For optimal image, position the screen so that it is not in direct sunlight or room light. Light falling directly
on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when
setting up the screen in a sunny or bright room.
• A polarizing screen cannot be used with this projector.
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according to the desired picture size.
Example of standard setup
Image
Lens shifted to lowest position
90°
Lens center
H1
Lens shifted to highest position
H2
90°
Lens center
L
L : Projection distance
H1 : Distance from the lens center to the bottom of the image
(when the lens is shifted to the lowest position)
H2 : Distance from the lens center to the bottom of the image
(when the lens is shifted to the highest position)
Note
• For details, refer to “Picture (Screen) Size and Projection Distance” on page 16.
-14
Projection (PRJ) Mode
The projector can use any of the 4 projection modes, shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ Mode in “Options” menu. See page 45.)
■ Ceiling mounted, front projection
■ Table mounted, front projection
Menu item ➞ “Ceiling + Front”
Menu item ➞ “Front”
Menu item ➞ “Rear”
Setup
■ Ceiling mounted, rear projection
(with a translucent screen)
■ Table mounted, rear projection
(with a translucent screen)
Menu item ➞ “Ceiling + Rear”
Ceiling-mount Setup
■ It is recommended that you use the optional Sharp ceiling-mount bracket for this installation. Before mounting
the projector, contact your nearest Sharp Authorized Service Center or Dealer to obtain the recommended
ceiling-mount bracket (sold separately).
• AN-NV6T ceiling-mount bracket, its AN-TK201 and AN-TK202 extension tubes.
■ Invert the image by setting “Ceiling + Front” in “PRJ Mode”. See page 45 for use of this function.
Indication of the Projection Image Size and Projection Distance
For details, refer to “Picture (Screen) Size and Projection Distance” on page 16.
Example : When using a wide screen (16:9)
Picture Size
300"
261
.5"×
200"
174
Projection
Distance
~ 54
16 '1
.7 0"
m
)
m ~
1 ~ 1
(4 3' 4 4'6
.1 5" .4 "
m ~ m
~ 18 )
(8 27 5.5 '2"
.3 '1 m
m "~ )
~ 3
11 6'
(1 40 .1 6"
2. '9 m
4 " )
~
52.3
"
29.4 ×
"
"
"×39
.2"
8
(2 '0"
.4 ~
m 10
~ '
1 3 10
(3 0' .3 "
.3 9" m)
60"
87.2
"×49
"
69.7
.1"
m
100"
80"
.3"×
98.1
147
-15
Setting Up the Projector (Continued)
Picture (Screen) Size and Projection Distance
The projection screen size varies according to the distance from the lens of the projector to the screen. Install
the projector so that projected images are projected onto the screen at the optimum size by referring to the
table below. Use the values in the table as a reference when installing the projector.
When using a wide screen (16:9): In case of displaying the 16:9 picture on the whole of the 16:9 screen.
16
Picture (Screen) size
9
: Projected image
Diag. (x)
300"
250"
200"
150"
120"
110"
100"
80"
60"
40"
x : Picture size (diag.) (inches)
L1 : Maximum Projection distance (ft/m)
L2 : Minimum Projection distance (ft/m)
Width
261.5" (6.6 m)
217.9" (5.5 m)
174.3" (4.4 m)
130.7" (3.3 m)
104.6" (2.7 m)
95.9" (2.4 m)
87.2" (2.2 m)
69.7" (1.8 m)
52.3" (1.3 m)
34.9" (0.9 m)
Height
147.1" (3.7 m)
122.6" (3.1 m)
98.1" (2.5 m)
73.5" (1.9 m)
58.8" (1.5 m)
53.9" (1.4 m)
49" (1.2 m)
39.2" (1.0 m)
29.4" (0.7 m)
19.6" (0.5 m)
Distance from the lens center to
the bottom of the image [H]
Minimum [L2]
Lower [H1]
Upper [H2]
40'9" (12.4 m) –147" (–374 cm) 0" (0 cm)
33'11" (10.3 m) –122" (–311 cm) 0" (0 cm)
27'1" (8.3 m)
–98" (–249 cm) 0" (0 cm)
20'3" (6.2 m)
–73" (–187 cm) 0" (0 cm)
16'2" (4.9 m)
–58" (–149 cm) 0" (0 cm)
14'10" (4.5 m)
–53" (–137 cm) 0" (0 cm)
13'5" (4.1 m)
–49" (–125 cm) 0" (0 cm)
10'9" (3.3 m)
–39" (–100 cm) 0" (0 cm)
8'0" (2.4 m)
–29" (–75 cm)
0" (0 cm)
5'3" (1.6 m)
–19" (–50 cm)
0" (0 cm)
Projection distance [L]
Maximum [L1]
54'10" (16.7 m)
45'8" (13.9 m)
36'6" (11.1 m)
27'4" (8.3 m)
21'10" (6.7 m)
20'0" (6.1 m)
18'2" (5.5 m)
14'6" (4.4 m)
10'10" (3.3 m)
7'2" (2.2 m)
The formula for picture size and projection distance
L1 = (0.05593x – 0.05550)/0.3048 (ft)
H1 = –1.2453x/2.54 (in)
L2 = (0.04158x – 0.05665)/0.3048 (ft)
H2 = 0
When using a normal screen (4:3) and projecting 4:3 image (SIDE BAR Mode)
4
Picture (Screen) size
3
: Screen
: Projected image
Diag. (x)
250"
200"
150"
120"
110"
100"
80"
60"
x : Picture size (diag.) (inches)
L1 : Maximum Projection distance (ft/m)
L2 : Minimum Projection distance (ft/m)
Width
200" (5.1 m)
160" (4.1 m)
120" (3.0 m)
96" (2.4 m)
88" (2.2 m)
80" (2.0 m)
64" (1.6 m)
48" (1.2 m)
Height
150" (3.8 m)
120" (3.0 m)
90" (2.3 m)
72" (1.8 m)
66" (1.7 m)
60" (1.5 m)
48" (1.2 m)
36" (0.9 m)
Projection distance [L]
Maximum [L1]
56'0" (17.1 m)
44'9" (13.6 m)
33'6" (10.2 m)
26'9" (8.2 m)
24'6" (7.5 m)
22'3" (6.8 m)
17'9" (5.4 m)
13'4" (4.1 m)
Distance from the lens center to
the bottom of the image [H]
Minimum [L2]
Lower [H1]
Upper [H2]
41'7" (12.7 m) –150" (–381 cm) 0" (0 cm)
33'2" (10.1 m) –120" (–305 cm) 0" (0 cm)
24'10" (7.6 m)
–90" (–229 cm) 0" (0 cm)
19'10" (6.1 m)
–72" (–183 cm) 0" (0 cm)
18'2" (5.5 m)
–66" (–168 cm) 0" (0 cm)
16'6" (5.0 m)
–60" (–152 cm) 0" (0 cm)
13'2" (4.0 m)
–48" (–122 cm) 0" (0 cm)
9'10" (3.0 m)
–36" (–91 cm)
0" (0 cm)
The formula for picture size and projection distance
H1 = –1.524x/2.54 (in)
L1 = (0.06845x – 0.05550)/0.3048 (ft)
H2 = 0
L2 = (0.05089x – 0.05665)/0.3048 (ft)
When using a normal screen (4:3): In case of setting the 16:9 picture to the full horizontal width of the 4:3 screen.
4
Picture (Screen) size
3
: Screen
: Projected image
Diag. (x)
250"
200"
150"
120"
110"
100"
80"
60"
x : Pictre size (diag.) (inches)
L1 : Maximum Projection distance (ft/m)
L2 : Minimum Projection distance (ft/m)
Width
200" (5.1 m)
160" (4.1 m)
120" (3.0 m)
96" (2.4 m)
88" (2.2 m)
80" (2.0 m)
64" (1.6 m)
48" (1.2 m)
Height
150" (3.8 m)
120" (3.0 m)
90" (2.3 m)
72" (1.8 m)
66" (1.7 m)
60" (1.5 m)
48" (1.2 m)
36" (0.9 m)
Projection distance [L]
Maximum [L1]
41'11" (12.8 m)
33'6" (10.2 m)
25'1" (7.6 m)
20'0" (6.1 m)
18'4" (5.6 m)
16'8" (5.1 m)
13'3" (4.1 m)
9'11" (3.0 m)
Minimum [L2]
31'1" (9.5 m)
24'10" (7.6 m)
18'7" (5.7 m)
14'10" (4.5 m)
13'7" (4.1 m)
12'4" (3.8 m)
9'10" (3.0 m)
7'4" (2.2 m)
Distance from the lens center to
the bottom of the image [H]
Lower [H1]
Upper [H2]
–112" (–286 cm) 0" (0 cm)
–90" (–229 cm) 0" (0 cm)
–67" (–171 cm) 0" (0 cm)
–54" (–137cm)
0" (0 cm)
–49" (–126 cm) 0" (0 cm)
–45" (–114 cm) 0" (0 cm)
–36" (–91 cm)
0" (0 cm)
–27" (–69 cm)
0" (0 cm)
The formula for picture size and projection distance
H1 = –1.143x/2.54 (in)
L1 = (0.05133x – 0.05550)/0.3048 (ft)
H2 = 0
L2 = (0.03817x – 0.05665)/0.3048 (ft)
Note
• Allow a margin of error in the value in the diagrams above.
• When the distance from the lens center to the bottom of the image (H) is a negative number, this indicates
that the bottom of the image is below the lens center.
-16
Samples of Cables for Connection
• For more details of connection and cables, refer to the operation manual of the connecting equipment.
• You may need other cables or connectors not listed below.
Equipment
Audio-visual
equipment
Input signal
Cable
Terminal on the
projector
HDMI video
HDMI cable (commercially available)
HDMI1, 2
Component
video
Component cable (commercially available)
COMPONENT/
RGB1, 2
3 RCA to 15-pin D-sub cable (sold separately: AN-C3CP2) DVI
DVI to 15-pin D-sub adaptor (sold separately: AN-A1DV)
Camera/video game
3 RCA to 15-pin D-sub cable DVI to 15-pin D-sub adaptor
RGB video
S-video
5 RCA RGB cable (commercially available)
COMPONENT/
RGB1, 2
S-video cable (commercially available)
S-VIDEO
Connections
Terminal for Dedicated cable attached to the connected equipment COMPONENT/
using the
RGB1, 2
dedicated
cable
Terminal for Dedicated cable attached to the connected equipment
using the
dedicated
cable
Video
Video cable (commercially available)
VIDEO
Terminal for Dedicated cable attached to the connected equipment
using the
dedicated
cable
Computer
RGB video
DVI to D-sub cable (supplied accessory)
DVI
DVI cable (sold separately: AN-C3DV)
-17
Connecting to Video Equipment
Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off the devices
to be connected. After making all connections, turn on the projector and then the other devices.
Connecting Equipment with HDMI Output Terminal to the HDMI Terminal on the Projector
HDMI is a new specialized interface capable of delivering a video and audio signal to the terminal using just one cable.
Since this projector does not support an audio signal by itself, use an amplifier or other audio device.
For video connection, use a cable that conforms to HDMI standards. Using cables that do not conform to HDMI
standards may result in a malfunction.
HDMI-compatible device
To HDMI1 or 2 terminal
To HDMI output terminal
HDMI cable (type A)
(commercially available)
Note
• HDMI (High-Definition Multimedia Interface) is a digital AV interface that can deliver a high-definition video
signal, multi-channel audio signal, and bi-directional control signal all in just one cable.
• Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the digital
video signal does not degrade when transmitted, and a high-quality image with a simple connection can
be enjoyed.
Connecting Equipment with the HDMI Output Terminal to the DVI Terminal on the Projector
HDMI-compatible device
To DVI terminal
To HDMI output terminal
DVI to HDMI cable
(commercially available)
Note
• When connecting the projector to the video equipment in this way, select “Signal Type” in the “Options”
menu. See page 44.
• When a DVI to HDMI conversion cable is connected to the HDMI terminal, a proper picture may not be
displayable.
-18
Connecting Video Equipment with the DVI Output Terminal to the DVI Terminal on the Projector
DVD Player,etc.
To DVI terminal
To DVI Digital output terminal
DVI cable
(sold separately: AN-C3DV)
Note
• When connecting the projector to the video equipment in this way, select “Signal Type” in the “Options”
menu. See page 44.
Connections
Connecting Component Video Equipment to the DVI Terminal on the Projector
DVD Player,etc.
To component output terminal
To DVI terminal
3 RCA to 15-pin D-sub cable
(sold separately: AN-C3CP2)
DVI to 15-pin D-sub adaptor
(sold separately: AN-A1DV)
Note
• When connecting the projector to the video equipment in this way, select “Signal Type” in the “Options”
menu. See page 44.
-19
Connecting to Video Equipment (Continued)
Connecting RGB Equipment to the DVI Terminal on the Projector
DVD Player,etc.
To DVI terminal
To RGB output terminal
DVI to D-sub cable
(supplied accessory)
Note
• When connecting the projector to the video equipment in this way, select “A. RGB” for “Signal Type” in
the “Options” menu. See page 44.
Connecting RGB Equipment to the COMPONENT/RGB Terminals on the Projector
DVD Player,etc.
To analog RGB
output terminal
To COMPONENT/RGB 1 or 2 terminals
5 RCA RGB cable
(commercially available)
Note
• The (HD/C sync) and (VD) terminals may be used depending on the specifications of the RGB equipment
connected to this projector. Please refer to the operation manual of the RGB equipment for details.
-20
Connecting Component Video Equipment to the COMPONENT/RGB Terminals on the Projector
DVD Player,etc.
To component output terminal
To COMPONENT/RGB 1 or 2 terminals
Component cable
(commercially available)
Connections
-21
Connecting to Video Equipment (Continued)
Connecting to Equipment with S-video Output Terminal
DVD Player,etc.
To S-video output terminal
To S-VIDEO terminal
S-video cable
(commercially available)
Connecting to Equipment with Video Output Terminal
DVD Player,etc.
To video output terminal
To VIDEO terminal
Composite video cable
(commercially available)
-22
Connecting to a Computer
Ensure that the computer is the last device to be turned on after all the connections are made.
Connecting to a Computer Using a DVI Cable
Computer
To DVI terminal
To DVI Digital output terminal
DVI cable
(sold separately: AN-C3DV)
Note
• When connecting the projector to the video equipment in this way, select “Signal Type” in the “Options”
menu. See page 44.
Connections
Connecting to a Computer Using the DVI to D-sub Cable
Computer
To DVI terminal
To RGB output terminal
DVI to D-sub cable
(supplied accessory)
Note
• When connecting the projector to the video equipment in this way, select “Signal Type” in the “Options”
menu. See page 44.
• Refer to “Computer Compatibility Chart” on page 60 for a list of computer signals compatible with the
projector. Use with computer signals other than those listed may cause some of the functions not to work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Sharp
Authorized Service Center or Dealer.
• Depending on the computer you are using, an image may not be projected unless the computer’s external
output port is switched on. (e.g. Press “Fn” and “F5” keys simultaneously when using a SHARP notebook
computer). Refer to the specific instructions in your computer’s operation manual to enable your computer’s
external output port.
-23
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer, the computer can be used to control
the projector and check the status of the projector.
When connecting to a computer using an RS-232C serial control cable
Computer
To RS-232C terminal
To RS-232C terminal
RS-232C serial control cable (cross type, commercially available)
Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
operation manual of the computer for details.
• For details on RS-232C specifications and commands, see page 52.
Info
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may
damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This
may damage your computer.
-24
Turning the Projector On/Off
Supplied
accessory
Connecting the Power
Cord
Power cord
Plug the supplied power cord into the
AC socket on the rear of the projector.
• The power indicator illuminates red, and the
projector enters standby mode.
Turning the Projector On
Before performing the steps in this section,
connect any equipment that you use with the
projector. (See pages 18-25.)
Remove the lens cap and press
on the projector or
ON
ON on the remote
Info
• English is the factory preset language. If you want to
change the on-screen display to another language,
change the language according to the procedure on
page 45.
control.
• The power indicator illuminates blue.
Power indicator
Lamp indicator
Note
ON
Basic Operation
• About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
Blue: The lamp is ready.
Blinking in blue: The lamp is warming up.
Red: The lamp is shut down abnormally
or the lamp should be replaced.
• When switching on the projector, a slight
flickering of the image may be experienced
within the first minute after the lamp has been
illuminated. This is normal operation as the
lamp’s control circuitry is stabilizing the lamp
output characteristics. This does not indicate
malfunction.
• If the projector is put into standby mode and
immediately turned on again, the lamp may
take some time to illuminate.
STANDBY
ON button
STANDBY button
Lens cap
-25
Turning the Projector On/Off (Continued)
Turning the Power Off
(Putting the Projector into Standby
Mode)
1
2
Press
STANDBY on the projector or
STANDBY on the
remote control, then press that
button again while the confirmation message is displayed, to
put the projector into standby
mode.
Unplug the power cord from the
AC outlet after the cooling fan
stops.
• The power indicator on the projector
blinks in blue while cooling.
• The power indicator changes to red
when the projector finishes cooling.
-26
□On-screen display
□
Info
• Do not unplug the power cord during projection or
cooling fan operation. This can cause damage due to
the rise in internal temperature, as the cooling fan also
stops.
• When connected to equipment such as an amplifier, be
sure to turn off the power to the equipment connected
first and then to the projector.
Image Projection
Switching the Input
Mode
Adjustment
buttons
(□/▼)
Select the appropriate input mode for the connected equipment.
ENTER
Press Input Mode Select buttons or
INPUT on the remote control to select
the input mode.
• When
Input Mode Select buttons
INPUT on the remote control or
INPUT on the projector is pressed, the Input
list appears. While the Input list is displayed,
follow the procedure below to switch the Input
mode.
INPUT or □/▼ to select the desired
1Press
input mode.
ENTER.
2Press
ENTER is not pressed, the projector
• If
switches to the selected input mode in a
few seconds.
INPUT
Input mode menu
Note
Basic Operation
• When no signal is received, “NO SIGNAL”
will be displayed. When a signal that the
projector is not preset to receive is received,
“NOT REG.” will be displayed.
Adjusting the Projected
Image
1. Adjusting the Focus
Focus ring
You can adjust the focus with the focus ring on the
projector.
Rotate the focus ring to adjust the focus while
watching the projected image.
2. Adjusting the Image Size
m in
Zoo
ut
mo
Zoo
Zoom knob
You can adjust the image size using the zoom knob
on the projector.
Move the zoom knob to enlarge or shrink the
image size.
-27
Image Projection (Continued)
3. Adjusting the Projector Angle
Using the Adjustment Feet
The inclination of the projector can be adjusted using
the adjustment feet when the projector is placed on
an uneven surface or when the screen is slanted.
1
2
Lift the projector to adjust its
height while pressing the foot
releases.
Remove your hands from the
foot releases after the height has
been adjusted.
Foot releases
• The angle of projection is adjustable up
to 5 degrees from the surface on which
the projector is placed.
3
Rotate the adjustment feet to
make fine adjustment.
• Rotate the adjustment feet to gradually
raise or lower the projector. Ensure that the
projector is stable and does not wobble.
Adjustment feet
Note
• When the height of the projector is adjusted, the
image may become distorted, depending on the
relative positions of the projector and the screen.
Info
• Do not apply too much pressure on the projector when the adjustment feet are stuck out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
• Hold the projector firmly while lifting or carrying.
• Do not hold by the lens area.
4. Adjusting the Vertical
Position of the Image
You can move the projected image vertically by
turning the lens shift dial.
Lens shift dial
Up
n
Info
• Do not turn the lens shift dial beyond the
upper limit and lower limit positions. This may
cause the projector to malfunction.
-28
Dow
Operating with the Remote Control
Switching the Iris Setting
Adjustment buttons
("/'/\/|)
This function controls the quantity of the
projected light and the contrast of the image.
Press
FREEZE
ENTER
IRIS.
• Each time the button is pressed while the display
is on, the mode changes in the following order:
HIGH BRIGHTNESS MODE
IRIS
PICTURE MODE
MEDIUM MODE
CONTRAST
HIGH CONTRAST MODE
BRIGHT
Note
• For details, see page 37.
Adjusting the Contrast
1
2
CONTRAST.
Press \ or | to adjust the contrast.
Press
1
2
Press
FREEZE.
• The projected image is frozen.
Press
FREEZE again to return
to the moving image from the currently connected device.
ENTER.
Selecting the Picture Mode
Note
• For details, see page 36.
You can select the appropriate picture mode to best
match the projected image you are watching.
Press
Adjusting the Quantity of Light
1
2
3
Press
BRIGHT.
Press \ or | to adjust the quantity of light.
Press
PICTURE MODE.
• Each time the button is pressed while the display
is on, the mode changes in the following order:
STANDARD
NATURAL
DYNAMIC
MEMORY
MOVIE2
MOVIE1
Note
• For details, see page 36.
ENTER.
Note
• For details, see page 36.
-29
Basic Operation
3
Press
Freezing a Moving Image
Selecting the Screen Size
RETURN button
RESIZE button
Resize Mode
This function allows you to modify or customize the
resize mode to enhance the input image.
Press
RESIZE on the projector or
RESIZE on the remote control.
Note
• The RESIZE function that can be selected
varies depending on the input signal (resolution and vertical frequency).
• To return to the standard image, press
RETURN while “RESIZE” is displayed.
RETURN
RESIZE
Resize Mode
RESIZE
Output screen image
STRETCH
An image compressed from a 16:9 aspect ratio to a 4:3 aspect ratio
is restored to a 16:9 aspect ratio and displayed at full-screen.
NORMAL
(Computer)
The image is displayed with the original aspect ratio.
SIDE BAR
(Video)
An image with a 4:3 aspect ratio is displayed without any changes.
SMART STRETCH
An image with a 4:3 aspect ratio is widened to fit the entire screen.
-30
RESIZE
Output screen image
CINEMA ZOOM
A CinemaScope image or an image with a 16:9 aspect ratio is
displayed at full-screen
ZOOM 14:9
An image with a 14:9 aspect ratio and letterboxing is enlarged while
maintaining the original aspect ratio.
SMART ZOOM
An image with a 4:3 aspect ratio is slightly enlarged.
DOT BY DOT
The image is displayed according to the original input signal.
About Copyrights
-31
Basic Operation
• When using the RESIZE function to select an image size with a different aspect ratio to a TV program or video
image, the image will look different from its original appearance. Keep this in mind while choosing an image
size.
• The use of the RESIZE, Subtitle, or Overscan function to compress or stretch the image for commercial
purposes/public displays in a café, hotel, etc. may be an infringement of copyright protected by law for
copyright holders. Please use caution.
• While watching non-widescreen images (4:3), if you use the RESIZE function to fill the screen or use the
Overscan function to change the aspect ratio of a fixed-ratio input signal, parts of the outer edge of the image
will be cut off or distorted. To watch original images as the producers intended, set “RESIZE” to “SIDE BAR”
and Overscan to its default setting.
Menu Bar Items
The following shows the items that can be set in the projector.
The selectable items vary depending on the selected input, input signals, or adjustment
values. Items that cannot be selected will be grayed out.
Main menu
Picture
Page 36
Sub menu
Main menu
Picture Mode
Page 36
Gamma
Page 40
Standard
Natural
Dynamic
Movie1
Movie2
Memory
Sub menu
Gamma Position
Gamma
All Colors
Red
Green
Blue
Contrast
–90
+90
Bright
–90
+90
Color
–30
+30
Tint
–30
+30
All Colors
Red
Green
Blue
Black Detail
–30
–30
–30
+30
+30
+30
–30
–30
–30
+30
+30
+30
–30
–30
–30
+30
+30
+30
White Detail
Sharp
–30
+30
CLR Temp
5500
10500
All Colors
Red
Green
Blue
Page 36
Gamma Position
Page 37
Standard
Natural
Dynamic
Movie1
Movie2
Custom
IRIS
High Brightness
Medium Mode
High Contrast
Page 37
Lamp Setting
Page 37
Bright
Eco + Quiet
Advanced
C.M.S.
Page 37
Page 37
Reset
Page 39
Reset
C.M.S. - Hue
Red
–30
+30
C.M.S. - Saturation
Yellow
–30
+30
C.M.S. - Value
Green
–30
+30
Reset
Cyan
–30
+30
Blue
–30
+30
Magenta
–30
+30
Reset
BrilliantColorTM
Page 38
On
Off
Progressive
Page 38
3D Fast
3D Slow
2D+
Film Mode
Page 38
Auto
Off
DNR
Page 38
MNR
Page 38
Unveil Control
Page 39
Automatic Contrast
Page 39
-32
Off
Level 1
Level 2
Level 3
Standard
Natural
Dynamic
Movie1
Movie2
Custom
Main menu
Fine Sync
Page 41
*1
Sub menu
Clock
–150
–60
Phase
H-Pos
–150
V-Pos
–60
Main menu
Options
+150
–30
+30
Subtitle
Page 42
–30
+30
+150
Overscan
Page 42
10
0%
+60
White Level
–30
+30
Black Level
–30
+30
Page 42
+60
Reset
Page 42
Reset
Special Modes
Signal Info
Auto Sync
Sub menu
Image Shift
Page 42
Resolution
Hor Freq
Vert Freq
Page 43
On
Off
LED
Page 43
Off
Normal
High Speed
Lamp Timer(Life)
Page 43
OSD Display
Page 43
When S-VIDEO or VIDEO is
selected for the input mode
On
Off
Video System
Page 43
Auto
PAL
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL-60
When COMPONENT is selected
for the input mode
Signal Type
Page 44
Auto
RGB
Component
When DVI is selected for the
input mode
D.PC RGB
D.PC COMP.
D.VIDEO RGB
D.VIDEO COMP.
A. RGB
A. COMP.
When HDMI is selected for the
input mode
Auto
RGB
YCbCr4:4:4
YCbCr4:2:2
*2
Auto
ITU601
ITU709
Color Space
Page 44
*2,3
Auto
Standard
Enhanced
Background
Page 44
Logo
Blue
None
Economy Mode
RS-232C Port [ON/OFF]
Auto Power Off [ON/OFF]
Pages 44, 45
RS-232C
Page 45
9600 bps
38400 bps
115200 bps
Fan Mode
Page 45
Normal
High
PRJ Mode
Front
Ceiling + Front
Rear
Ceiling + Rear
Page 45
All Reset
Page 45
Language
Page 45
English
Deutsch
Español
Nederlands
Français
Italiano
Useful Feature
Dynamic Range
Page 44
Svenska
Português
*1: The “Fine Sync” menu is not available for S-VIDEO or VIDEO Input.
*2: Can be set for HDMI Input.
*3: Can be set for DVI Input.
-33
Using the Menu Screen
RETURN button
ENTER button
Adjustment buttons
('/"/\/|)
MENU button
Adjustment buttons
('/"/\/|)
ENTER
MENU
RETURN
Menu Selections (Adjustments)
• This operation can also be performed by using
the buttons on the projector.
(Example: Adjusting “Bright”)
1
2
Press
MENU.
• The “Picture” menu screen for the selected input mode is displayed.
Press | or \ to select the menu
screen to adjust on the menu
bar.
Note
• The “Fine Sync” menu is not available
for selecting S-VIDEO or VIDEO.
-34
Example: “Picture” menu screen when
COMPONENT is selected for
input mode
Menu bar
3
Press ' or " to select the item
you want to adjust.
(Example: Selecting “Bright”)
To adjust the projected
image while viewing it
Press
ENTER.
• The selected adjustment item (e.g.
“Bright”) will be displayed at the bottom
of the screen.
• When ' or " is pressed, the next
item will be displayed. (e.g. “Bright” is
replaced with “Color” by pressing ".)
Singleadjustment
items
Note
• Press
RETURN to return to the
previous screen.
4
Press | or \ to adjust the item
selected.
• The adjustment is stored.
• For some menu items, press | to display its submenu and press ' or "
to select an adjustment item, and then
press
ENTER.
5
Press
MENU.
• The menu screen will disappear.
Useful Feature
-35
Picture Adjustment (“Picture” Menu)
Menu operation ⇒ Page 34
1 Selecting the Picture Mode
This function allows you to select the picture mode that best suits the room brightness and the type of image being
projected.
Selectable
items
Description
Standard
Natural
Dynamic
Movie1
The main default settings of each item when selecting Picture Mode
CLR Temp
BrilliantColor™
IRIS
Lamp Setting
7500
Off
High Brightness
Bright
7500
Off
High Brightness
Bright
7500
On
High Brightness
Bright
6500
Off
Medium Mode
Eco + Quiet
For standard image
A balanced color image is obtained.
A vivid image is obtained.
For viewing images with the brightness
slightly toned down in a darkened
room
Movie2
For viewing images with the brightness
6500
Off
High Contrast
Eco + Quiet
slightly boosted in a darkened room
Memory
Allows you to store your picture
7500
Off
High Brightness
Bright
adjustment settings. The settings
stored effect each input mode.
• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are retained in memory.
Note
• You can also press
PICTURE MODE on the remote control to select the picture mode. (See page 29.)
• The default settings are subject to change without notice.
2 Adjusting the Image
Adjustment items
Contrast
Bright
Color
Tint
Sharp
CLR Temp
\ button
| button
For less contrast.
For more contrast.
For less brightness.
For more brightness.
For less color intensity.
For more color intensity.
For making skin tones purplish.
For making skin tones greenish.
For less sharpness.
For more sharpness.
For making images slightly more reddish For making images slightly more bluish
(slightly warmer colors).
(slightly cooler colors).
Note
• To reset all adjustment items, select “Yes” in “Reset” and press
ENTER. The Picture Mode settings of the
selected input return to the default settings.
• As for “Contrast” and “Bright”, you can make adjustments directly by using
CONTRAST and
BRIGHT, respectively, on the remote control. (See page 29.)
-36
Menu operation ⇒ Page 34
3 Selecting the Gamma Position
This function allows you to select the desired gamma
position.
See page 40 for details.
Note
• Gamma can be adjusted in greater detail with
“Gamma” on the menu screen.
4 Switching the Iris Setting
This function controls the quantity of the projected light
and the contrast of the image.
Selectable items
High Brightness
Medium Mode
High Contrast
Description
High brightness is given priority over
high contrast.
Intermediate mode between high contrast and high brightness.
High contrast is given priority over high
brightness.
Note
• You can also use
IRIS on the remote control
to change the Iris. (See page 29.)
5 Lamp Setting
SelectBrightable items ness
100%
Eco +
Quiet
Approx.
80%
Note
• When “Lamp Setting” is set to “Eco+Quiet”, the
power consumption will decrease and the lamp
life will extend. (Projection brightness decreases
approximately 20%.)
“Advanced” allows you to make even finer adjustments
to the image so that it appears just the way you want
it to.
To display the Advanced menu, select “Advanced” and
press
ENTER.
Note
• When the “Advanced” settings are displayed,
select “Advanced” again and press
ENTER
to return to the “Picture” menu.
7 Adjusting the Colors
Select “C.M.S.” (Color Management System) in the
“Advanced” menu and then press
ENTER.
This function adjusts each of the six main colors that
comprise the color wheel, altering their “Hue”, “Saturation”, or “Value”.
Selectable items
C.M.S.-Hue
C.M.S.-Saturation
C.M.S.-Value
Reset
Description
Sets the hue of the main colors.
Sets the Saturation of the main colors
Sets the Value of the main colors.
The adjustments of “Hue”, “Saturation”
and “Value” of all colors are reset to the
default setting.
Adjusting “Hue”, “Saturation”, or “Value”.
1 Press ' or " to select either “Hue”, “Saturation”, or
“Value” and then press
ENTER.
2 Select the color to be adjusted with ' or " and
adjust it with \ or |.
• When you press
ENTER, the adjustment bar for the
selected system color will be displayed at the bottom
of the screen. Use this bar to make adjustments while
viewing the effects on-screen.
Useful Feature
Bright
Power
consumption
Lamp Life
(When using
AC 100V)
Normal
320W
Approx.
2,000
hours
Low
265W
Approx.
3,000
hours
Fan
sound
6 Using the Advanced
Example of adjusting the “Hue”
Main colors
Red
Yellow
Green
Cyan
Blue
Magenta
\ button
Closer to magenta
Closer to red
Closer to yellow
Closer to green
Closer to cyan
Closer to blue
| button
Closer to yellow
Closer to green
Closer to cyan
Closer to blue
Closer to magenta
Closer to red
• When “Saturation” is selected, the selected color
becomes lighter (\) or thicker (|).
• When “Value” is selected, the selected color becomes darker (\) or brighter (|).
• To reset the adjustment values of each color to the
default settings, select “Yes” in “Reset” and press
ENTER.
-37
Picture Adjustment (“Picture” Menu) (Continued)
Menu operation ⇒ Page 34
8 Adjusting the BrilliantColorTM
TM
q Reducing Image Noise (DNR)
TM
BrilliantColor uses Texas Instruments’ BrilliantColor
technology. The image becomes brighter while the color
reproduction is kept at a high level.
Selectable items
On
Description
The BrilliantColorTM function is
activated.
Off
The BrilliantColor TM function is not
activated.
9 Selecting the Progressive Mode
For selecting the progressive display of a video signal.
Selectable items
3D Fast
3D Slow
2D+
Description
Useful to display fast-moving images
such as sports and action films.
Useful to display relatively slow-moving
images such as drama and documentary more clearly.
This mode is ideal for games, etc.
• When using progressive inputs, “Progressive’’
cannot be selected.
0 Selecting the Film Mode
This function provides high-quality playback of
images originally projected at 24 fps, such as movies
on DVDs.
Description
Films are detected automatically.
Films are not detected.
Note
• When using progressive inputs, “Film Mode”
cannot be selected.
-38
Selectable items
Off
Level 1
Level 2
Level 3
Description
The DNR function is not activated.
Sets the DNR level for viewing a clearer
picture.
Note
Set “DNR” to “Off” in the following cases:
• When the image is blurry.
• When the contours and colors of moving images
drag.
• When TV broadcasts with weak signals are projected.
wMosquito Noise Reduction (MNR)
The so-called Mosquito Noise (flickering) can be
reduced.
Note
Selectable items
Auto
Off
Video digital noise reduction (DNR) provides high quality
images with minimal dot crawl and cross color noise.
Selectable items
Off
Level 1
Level 2
Level 3
Description
MNR does not function.
Sets the MNR level for viewing a clearer
picture.
Menu operation ⇒ Page 34
e Adjusting the Unveil Control
This function uses edge enhancement to give the
impression of added depth to images.
Selectable items
Off
Description
The Unveil Control function is not
activated.
Level 1
Level 2
Level 3
Sets the Unveil Control level for viewing
an image with the impression of added
depth.
r Adjusting the Automatic Contrast
This function automatically adjusts the image contrast
to suit the scene.
Selectable items
Off
Level 1
Level 2
Level 3
Description
The Automatic Contrast function is
not activated.
Sets the Automatic Contrast level.
t Resetting All Adjustment Items
This function allows you to reset all adjustment items to
the default setting.
Selectable items
No
Yes
Description
Does not do resetting.
Resets all adjustment items.
Useful Feature
-39
Gamma Adjustment (“Gamma” Menu)
Menu operation ⇒ Page 34
2 Adjusting the Gamma
Adjust the gamma curve to suit your preferences.
■ Gamma
Selectable
\ button
| button
item
All Colors You can make sync adjustment for the Red,
Green and Blue mentioned below.
For giving greater
For giving greater
depth to brighter por- depth to darker portion of image
tion of image
Red
For giving greater depth
to brighter portion of
image in red color.
For giving greater depth
to brighter portion of
image in green color.
For giving greater depth
to brighter portion of
image in blue color.
Green
Blue
1 Selecting the Gamma Position
You can select the desired gamma position according
to the image being projected.
Selectable item
Standard
Natural
Dynamic
Movie1
Movie2
Custom
Description
Sharp default setting
Gives a solid and understated image
quality
For viewing images in relatively bright
surroundings
For viewing images with the brightness
slightly toned down in a darkened
room
For viewing images with the brightness
slightly boosted in a darkened room
Uses special software that allows the
gamma curve to be adjusted. For more
information on the special software, visit
the Sharp website at:
http://sharp-world.com/projector/.
■ White Detail
Selectable
item
\ button
| button
All Colors
You can make sync adjustment for the Red,
Green and Blue mentioned below.
For less contrast
For more contrast
Red
For less contrast in
red color
For more contrast in
red color
Green
For less contrast in
green color
For more contrast in
green color
Blue
For less contrast in
blue color
For more contrast in
blue color
■ Black Detail
Selectable
item
\ button
| button
All Colors
You can make sync adjustment for the Red,
Green and Blue mentioned below.
For less brightness
For more brightness
Red
For less brightness in
red color
For more brightness
in red color
Green
For less brightness in
green color
For more brightness
in green color
Blue
For less brightness in
blue color
For more brightness
in blue color
Note
• The gamma position you set in this menu can be
selected in the “Gamma Position” in the “Picture”
menu.
For giving greater depth
to darker portion of image in red color.
For giving greater depth
to darker portion of image in green color.
For giving greater depth
to darker portion of image in blue color.
• When you select an adjustment item and press
ENTER, the adjustment bar for the selected
adjustment item will be displayed at the bottom of
the screen. Use this bar to make adjustments while
viewing the effects on-screen.
Note
• To reset all adjustment items, select “Yes” in
“Reset” and press
ENTER.
-40
Computer Image Adjustment (“Fine Sync” Menu)
Menu operation ⇒ Page 34
The illustration shown here is for explanation and may
be different from the actual on-screen display.
3 Checking the Input Signal
This function allows you to check the current input signal
information.
4 Auto Sync (Auto Sync Adjustment)
Selectable item
Off
1 Adjusting the Computer Image
Normal
High Speed
Use the Fine Sync function in case of irregularities
such as vertical stripes or flickering in portions of the
screen.
Selectable item
Clock
Phase
H-Pos
V-Pos
Description
Adjusts vertical noise.
Adjusts horizontal noise (similar to
tracking on your VCR).
Centers the on-screen image by
moving it to the left or right.
Centers the on-screen image by
moving it up or down.
Note
• You can automatically adjust the computer image
by setting “Auto Sync” in the “Fine Sync” menu
to “Normal” or “High speed”, or pressing
AUTO SYNC on the remote control.
• Depending on the type of input signal, the
adjustment range for each setting may vary or the
adjustment may not be available at all.
• To reset all adjustment items, select “Yes” in
“Reset” and press
ENTER.
Description
Auto Sync adjustment is not
automatically performed.
Auto Sync adjustment will occur when
the projector is turned on or when
the input signals are switched, when
connected to a computer.
The “Normal” setting adjusts the
image synchronization more accurately
than the “High Speed” setting. For this
reason, it takes slightly longer to make
the adjustment.
Note
• Auto Sync adjustment is also performed by
pressing
AUTO SYNC on the remote
control.
• When setting “Auto Sync” to “Off” or “High
Speed”, and if
AUTO SYNC is pressed, Auto
Sync will be executed in “High Speed” mode. If
the button is pressed again within one minute,
Auto Sync will be executed in “Normal” mode.
• The Auto Sync adjustment may take some time
to complete, depending on the image of the
computer connected to the projector.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use manual
adjustments.
Useful Feature
2 Special Modes Setting
Ordinarily, the type of input signal is detected and the
correct resolution mode is automatically selected. However, for some signals, the optimal resolution mode in
“Special Modes” in the “Fine Sync” menu may need to
be selected to match the computer display mode.
Note
• Avoid displaying computer patterns which repeat
every other line (horizontal stripes). (Flickering
may occur, making the image hard to see.)
• Information on the currently selected input signal
can be confirmed in item 3.
-41
Using the “Options” Menu
Menu operation ⇒ Page 34
When HDMI is selected for the input mode.
The illustration shown here is for explanation and may
be different from the actual on-screen display.
2 Adjusting the Vertical Size of the
Display (Subtitle Setting)
With this function, you can adjust the vertical size of the
display to allow for subtitles.
\ button
| button
The image is compressed by adjusting the
vertical size of the display.
The image is enlarged by adjusting the
vertical size of the display.
Note
*1
*2
*3
*1 If the input mode is S-VIDEO or VIDEO input, the display
changes to the “Video System” screen.
*2 Displayed when the input mode is HDMI input.
*3 Displayed when the input mode is HDMI input or DVI
input with digital signals.
1 Adjusting the Image Position
You can move the projected image vertically.
• When changing the screen with the Subtitle setting, not only the bottom of the screen rises, but
also the upper part is changed to a certain point.
• The Subtitle setting can be adjusted more
effectively with the “Overscan” and “Image Shift”
functions.
• The Subtitle setting only works when “RESIZE”
is set to “SMART STRETCH”, “CINEMA ZOOM”,
“ZOOM 14:9” or “SMART ZOOM”.
• The adjustment area changes according to the
input signal.
• You can initialize the “Image Shift”, “Subtitle” and
“Overscan” settings to their respective default
setting by selecting “Yes” in “Reset” and pressing
ENTER.
3 Adjusting the Overscan
This function allows you to adjust the Overscan area
(display area).
\ button
| button
\ button
| button
Note
• The Image Shift function only works when
“RESIZE” is set to “SMART STRETCH”, “CINEMA
ZOOM”, “ZOOM 14:9” or “SMART ZOOM”.
• You can initialize the “Image Shift”, “Subtitle”
and “Overscan” settings to their respective
default setting by selecting “Yes” in “Reset” and
pressing
ENTER.
-42
Enlarges the image.
(The display area becomes smaller.)
Reduces the image.
(The display area becomes larger.)
Note
•You can adjust the Overscan area for the following
input signals and the RESIZE function.
- Input signal: VIDEO, 480I/480P, 540P, 576I/576P,
720P, 1035I or 1080I/1080P
- RESIZE function: “SIDE BAR”, “CINEMA
ZOOM”, “STRETCH” or “ZOOM 14:9”
• If the display area ratio is set too large, noise may
appear at the screen edges. If this happens, set
the display area ratio to a smaller value.
• Also read “About Copyrights” on page 31.
• You can initialize the “Image Shift”, “Subtitle”
and “Overscan” settings to their respective
default setting by selecting “Yes” in “Reset” and
pressing
ENTER.
Menu operation ⇒ Page 34
4 Adjusting the White Level/Black
Level
“White Level” adjusts the white level for variations in
the input signals.
“Black Level” adjusts the black level for variations in
the input signals.
Selectable
items
White Level
Black Level
\ button
| button
Gives better color re- Gives brighter and
production.
sharper images.
Darkens the image. Brightens the image.
Note
• It is recommended that the lamp be changed
when the remaining lamp life becomes 5%.
• The lamp life may vary depending on the usage
condition.
7 Setting On-screen Display
Selectable items
On
Off
Note
• You cannot adjust the white and black levels
when inputting a digital signal.
5 Turning LED Off
LEDs (indicators) on the projector can be turned off when
they are disturbing the projection.
Selectable items
On
Off
Description
LEDs are turned on.
LEDs are turned off while the projector
is in operation. (LEDs turn on while
the projector is in the standby mode,
warming up or indicating problems.)
8 Setting the Video System
When the input mode is S-VIDEO or VIDEO input, adjustment items for the “Video System” mode can be set.
The video input system mode is factory preset to “Auto”;
however, a clear picture from the connected audio-visual
equipment may not be received, depending on the video
signal difference. In that case, switch the video signal.
Selectable items
PAL
SECAM
NTSC4.43
Note
NTSC3.58
Description
When connected to PAL video
equipment.
When connected to SECAM video
equipment.
When reproducing NTSC signals in
PAL video equipment.
When connected to NTSC video
equipment.
Useful Feature
• When Auto Power Off function is set to “OFF”,
“LED” is set to “On” automatically. Be sure to set
Auto Power Off function to “ON” to use LED Off
function. (See page 45.)
Description
All on-screen displays are displayed.
Only the menus, input mode menu, the
adjustment bars for contrast and brightness and the warning messages (power
off, temperature, lamp replacement,
etc.) are displayed.
6 Checking the Lamp Life Status
You can confirm the cumulative lamp usage time and
the remaining lamp life (percentage).
Lamp usage condition
“Life”
Operated exclusively with
Lamp Setting set to “Eco +
Quiet”
Operated exclusively with
Lamp Setting set to “Bright”
Remaining lamp life
100%
5%
Approx.
Approx.
3,000
150
hours
hours
Approx.
Approx.
2,000
100
hours
hours
-43
Using the “Options” Menu (Continued)
Menu operation ⇒ Page 34
8 Signal Type Setting
When using an input mode other than S-VIDEO or VIDEO
input, set the signal type setting to the corresponding
input signal type (RBG or Component).
■ When COMPONENT is selected for the
input mode
Selectable items
Auto
RGB
Component
Description
Automatically selects the appropriate input signal between RGB and
Component.
Set when RGB signals are received.
Set when component signals are
received.
■ When DVI is selected for the input mode
Selectable items
D. PC RGB
D. PC COMP.
D. VIDEO RGB
D. VIDEO COMP.
A. RGB
A. COMP.
Description
Set when digital PC RGB signals are
received from the computer.
Set when digital PC component signals
are received from the computer.
Set when digital video RGB signals are
received from video equipment.
Set when digital video component
signals are received from video equipment.
Set when analog RGB signals are
received.
Set when analog component signals
are received.
■ When HDMI is selected for the input mode
This function sets the type of picture signal input from
HDMI-compatible equipment.
Selectable items
Auto
RGB
YCbCr4:4:4
YCbCr4:2:2
Description
Ordinarily, the Auto setting should be
used.
Displays images in RGB (Red/Green/
Blue) mode.
These modes display images using a
luminance signal (Y) to indicate contrast
and color difference signals (CbCr) to
show the colors. (Select whichever
mode gives the best image.)
9 Adjusting the Color Space
This function sets the color space for signals input from
an HDMI-compatible device.
Selectable items
Auto
ITU601
ITU709
0 Adjusting the Dynamic Range
An optimum picture may not be displayed if an HDMIcapable device’s output signal type and the projector’s
input signal type do not match. If this should occur,
switch “Dynamic Range”.
Selectable items
Auto
Description
In most circumstances, “Auto” should
be selected.
Standard
Enhanced
When the black levels of the image show
banding or appear faded, select the item
that results in the best picture quality.
q Selecting the Background Image
Selectable items
Logo
Blue
None
Description
SHARP logo screen
Blue screen
— (Black screen)
w Adjusting the Economy Mode
Setting the Economy mode:
1 Select “Economy Mode” and press |.
2 Press '/" to select the desired item and press
ENTER.
■ RS-232C Port
When the RS-232C port is set to “ON”, the RS-232C
function operates and consumes power even when the
projector is in Standby mode. Accordingly, the RS-232C
port should be set to “OFF” when it is not being used
so as to minimize the amount of power consumed when
the projector is in Standby mode.
Selectable items
ON
Note
Description
In most circumstances, “Auto” should
be selected.
Select the item that results in the best
picture quality.
OFF
• You can also select “Signal Type” using
RGB/COMP. on the remote control.
Description
The RS-232C is operating at all times
(to accept communications).
RS-232C does not operate when the
power supply is in standby.
Note
• When you control the projector by means of RS232C, select “ON”.
-44
Menu operation ⇒ Page 34
■ Auto Power Off
This function automatically switches the projector
to Standby mode if no signals are received for a set
period.
Selectable items
ON
OFF
Description
When no input signal is detected for
more than 15 minutes, the projector will
automatically enter standby mode.
The Auto Power Off function will be
disabled.
t Reversing/Inverting Projected
Images
This function allows the projector to be used in a wider
range of projection styles by allowing the image to be
inverted to suit the projection environment (location).
Selectable items
Front
Ceiling + Front
Note
Rear
• When the Auto Power Off function is set to “ON”,
5 minutes before the projector enters standby
mode, the message “Enter STANDBY mode in
X min.” will appear on the screen to indicate the
remaining minutes.
• When the Auto Power Off function is set to “OFF”,
“LED” is set to “On” automatically. Be sure to set
the Auto Power Off function to “ON” to use the
LED Off function. (See page 43.)
e Selecting the Transmission
Speed (RS-232C)
Make sure that both the projector and computer are set
for the same baud rate.
Selectable items
9600bps
Description
Transmission speed is slow.
38400bps
115200bps
Transmission speed is rapid.
This function changes the fan rotation speed.
Selectable items
Normal
High
Description
Suitable for normal environments.
Select this when using the projector at
altitudes of approximately 4,900 feet
(1,500 meters) or more.
• When “Fan Mode” is set to “High”, the fan rotation
• See page 15 for details of Projection (PRJ) Mode.
y Returning to the Default Settings
Use “All Reset” to initialize all the adjustments you have
made to the default settings.
Note
The following items cannot be initialized.
• “Fine Sync” menu
— Special Modes
• “Options” menu
— Lamp Timer (Life)
— Language
Other Function
Selecting the On-screen
Display Language
The projector can switch the on-screen display language
among 11 languages.
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
speeds up, and the fan noise becomes louder.
-45
Useful Feature
r Fan Mode Setting
Ceiling + Rear
Description
Normal image (Projected from the front
of the screen)
Inverted image (Projected from the
front of the screen with an inverted
projector)
Reversed image (Projected from the
rear of the screen or with a mirror)
Reversed and inverted image (Projected with a mirror)
Maintenance Indicators/Maintenance
■ The maintenance indicators (power, lamp and temperature warning indicators) on the projector will let
you be aware of problems inside the projector. If any of the indicators illuminates, follow the relevant
procedures given below.
Power indicator
Lamp indicator
Temperature warning indicator
About the temperature warning indicator
If the temperature inside the
projector increases, due to
blockage of the exhaust or
intake vent, or the setting loca” will blink in the lower left corner of
tion, “
the picture. If the temperature keeps on rising,
the lamp will turn off and the temperature warning
indicator will blink, the cooling fan will run, then
the projector will enter the standby mode. After
“
” appears, be sure to perform the measures
described on the table below.
Maintenance indicator
Abnormal
Normal
Condition
About the lamp indicator
■ When the remaining lamp
life becomes 5% or less,
(yellow) and “Change
The Lamp” will be displayed on the screen. When the percentage
becomes 0%, it will change to
(red), the lamp
will automatically turn off and then the projector
will automatically enter standby mode. At this
time, the lamp indicator will illuminate in red.
■ If you try to turn on the projector a fourth time
without replacing the lamp, the projector will
not turn on.
Problem
Possible Solution
Temperature
warning
indicator
Off
Red on
(Standby)
The internal
temperature is
abnormally high.
• Blocked exhaust or • Relocate the projector to an area
intake vent
with proper ventilation.
• Cooling fan break• Take the projector to your nearest
down
Sharp Authorized Service Center or
• Internal circuit failure Dealer for repair.
• Clogged exhaust or • Clean the exhaust and intake vents
according to the procedure on page 47.
intake vent
Lamp
indicator
Blue on*
Blue
blinks
when the
lamp is
active.
Red on
(Standby)
The lamp does
not illuminate.
• Burnt-out lamp
• Lamp circuit failure
Red blinks
Lamp replacement time.
Red blinks
The power
indicator blinks
in red when the
projector is on.
Power
indicator
Blue on*/
Red on
• Replace the lamp. (See page 48.)
Take the projector to your nearest
Sharp Authorized Service Center or
Dealer for repair.
• Please exercise care when replacing the lamp.
• The remaining lamp
life has become 5% • Securely install the lamp unit cover.
or less.
• The lamp unit cover
is open.
* Blue is off when “LED” is set to “Off”. (See page 43.)
-46
• Securely install the lamp unit cover.
• If the power indicator blinks
even when the lamp unit cover is
securely installed, contact your
nearest Sharp Authorized Service
Center or Dealer for advice.
Info
• If the temperature warning indicator illuminates and the projector enters the standby mode, ensure the
exhaust and intake vents are not blocked (page 6) and then try turning the power back on. Wait until the
projector has cooled down completely (at least 10 minutes) before plugging in the power cord and turning
the power back on.
• If the power is turned off for a brief moment due to power outage or some other cause while using the
projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red
and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power
cord in the AC outlet and then turn the power on again.
• The speed and pitch of the cooling fan may change during operation in response to internal temperature
changes. This is normal operation and does not indicate a malfunction.
• Do not unplug the power cord immediately after the projector has entered the standby mode or while the
cooling fan is running. The cooling fan runs for about 90 seconds.
Cleaning the projector
■ Be sure to unplug the power cord before cleaning the
projector.
■ The cabinet as well as the operation panel is made of
plastic. Avoid using benzene or thinner, as these can
damage the finish on the cabinet.
■ Do not use volatile agents such as insecticides on the
projector.
Do not attach rubber or plastic items to the projector for
long periods.
The effects of some of the agents in the plastic may
cause damage to the quality or finish of the projector.
■ Wipe off dirt gently with a soft flannel cloth.
■ When the dirt is hard to remove, soak a cloth in a mild
detergent diluted with water, wring the cloth well and
then wipe the projector.
Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a
small, inconspicuous area on the projector before use.
Cleaning the exhaust and intake vents
■ Use a vacuum cleaner to clean dust from the exhaust
vent and the intake vent.
■ The exhaust and intake vents should be cleaned every
100 hours of use. Clean the vents more often when the
projector is used in a dirty or smoky location.
ete
dd
Mil
nt
rge
Wax
Thinner
Mild detergent
diluted with water
Cleaning the lens
Info
• If you want to clean the exhaust and intake vents
during projector operation, be sure to press
STANDBY on the projector or
STANDBY on
the remote control and put the projector into
standby mode. After the cooling fan has stopped,
clean the vents.
Appendix
■ Use a commercially available blower or lens cleaning
paper (for glasses and camera lenses) for cleaning the
lens. Do not use any liquid type cleaning agents, as
they may wear off the coating film on the surface of the
lens.
■ As the surface of the lens can easily get damaged, be
sure not to scrape or hit the lens.
-47
Regarding the Lamp
Lamp
■ It is recommended that the lamp be replaced with a new one (sold separately) when the remaining
lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color
quality. The lamp life (percentage) can be checked with the on-screen display. (See page 43.)
■ Purchase a replacement lamp of type AN-K20LP from your place of purchase, nearest Sharp Authorized Service Center or Dealer.
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of
exposure to the gas, consult a doctor as soon as possible.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Service Center or
Dealer to assure safe operation.
Replacing the Lamp
Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn
or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.
■ Carefully change the lamp by following the instructions described in this section. *If you wish, you
may have the lamp replaced at your nearest Sharp Authorized Service Center or Dealer.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Service
Center or Dealer for repair.
-48
Removing and Installing the Lamp Unit
Warning!
• The lamp unit becomes very hot while the projector is operating. Do not remove the lamp
unit from the projector right after use. The lamp and parts around the lamp will be very hot
and may cause burns or injury.
Info
• Be sure to remove the lamp unit by the handle. Be sure not to touch the glass surface of
the lamp unit or the inside of the projector.
• To avoid injury to yourself and damage to the
lamp, be sure to carefully follow the steps
below.
• Do not loosen other screws than for the lamp
unit cover and lamp unit.
(As for the lamp unit, only the silver screws
are loosened.)
1
Optional
accessory
Lamp unit
(Type: AN-K20LP)
STANDBY
STANDBY button
Press
STANDBY on the projector or STANDBY on the remote control to put the projector
into the standby mode.
• Wait until the cooling fan stops.
2
3
4
Disconnect the power cord.
• Unplug the power cord from the AC
socket.
• Leave the lamp until it has fully cooled
down (about 1 hour).
AC socket
User service screws
Remove the lamp unit cover.
• Loosen the user service screws that
secure the lamp unit cover. Then open
the cover in the direction of the arrow.
Lamp unit cover
Lamp unit
Remove the lamp unit.
Securing screw
Appendix
• Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of the
arrow.
Handle
Securing screws
-49
Regarding the Lamp (Continued)
5
Insert the new lamp unit.
6
Attach the lamp unit cover.
• Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
• Close the lamp unit cover in the direction of the arrow. Then tighten the user
service screws.
Securing screws
2
Info
• If the lamp unit and lamp unit cover are not
correctly installed, the power will not turn on,
even if the power cord is connected to the
projector.
1
User service screws
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this
may cause the lamp to become damaged
or explode.
ENTER button
1
Connect the power cord.
2
Reset the lamp timer.
• Plug the power cord into the AC socket
of the projector.
• While holding down
ENTER, " and
| on the projector, press
projector.
ON on the
• “LAMP 0000H” is displayed, indicating
that the lamp timer is reset.
-50
Adjustment button"
AC socket
Adjustment button|
ON button
Connecting Pin Assignments
DVI-I Terminal: 29-pin connector
• DVI Digital Input
C3
C5
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
24 23 • • • ~ • • • 18 17
C4
C2
C1
16
8 7• • • • • ~ • • • • • 2 1
••••••••• ~ ••••••••• 9
• DVI Analog RGB Input
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
Not connected
Not connected
Not connected
Not connected
Not connected
DDC clock
DDC data
Vertical sync
Not connected
Not connected
Not connected
Not connected
Not connected
+5V power
Ground
Signal
T.M.D.S data 2–
T.M.D.S data 2+
T.M.D.S data 2 shield
Not connected
Not connected
DDC clock
DDC data
Not connected
T.M.D.S data 1–
T.M.D.S data 1+
T.M.D.S data 1 shield
Not connected
Not connected
+5V power
Ground
Pin No.
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
Signal
Hot plug detection
T.M.D.S data 0–
T.M.D.S data 0+
T.M.D.S data 0 shield
Not connected
Not connected
T.M.D.S clock shield
T.M.D.S clock+
T.M.D.S clock–
Not connected
Not connected
Not connected
Not connected
Ground
• DVI Analog Component Input
Pin No.
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
Signal
Hot plug detection
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Analog input Red
Analog input Green
Analog input Blue
Horizontal sync
Ground
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Ground
Pin No.
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
Signal
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Analog input PR/CR
Analog input Y
Analog input PB/CB
Not connected
Ground
RS-232C Terminal: 9-pin D-sub male connector
Pin No.
1
2
3
4
5
6
7
8
9
9876
54321
Signal
RD
SD
SG
Name
Receive Data
Send Data
Reserved
Signal Ground
Reserved
Reserved
Reserved
I/O
Input
Output
Reference
Not connected
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Not connected
HDMI Terminal
2
19
18
Pin No.
1
2
3
4
5
6
7
Name
Pin No.
T.M.D.S data 2+
8
T.M.D.S data 2 shield
9
T.M.D.S data 2–
10
T.M.D.S data 1+
11
T.M.D.S data 1 shield
12
T.M.D.S data 1–
13
T.M.D.S data 0+
Name
Pin No.
T.M.D.S data 0 shield
14
T.M.D.S data 0–
15
T.M.D.S clock+
16
T.M.D.S clock shield
17
T.M.D.S clock–
18
CEC
19
Name
Reserved
SCL
SDA
DDC/CEC ground
+5V power
Hot plug detection
Appendix
1
-51
RS-232C Specifications and Command Settings
PC control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type,
commercially available) to the projector. (See page 24 for connection.)
Communication conditions
Set the serial port settings of the computer as follows.
Signal format: Conforms to RS-232C standard.
Baud rate*: 9,600 bps / 38,400bps / 115,200bps
Data length: 8 bits
*Use the same settings for the projector and computer.
Parity bit: None
Stop bit: 1 bit
Flow control: None
Basic format
Send commands from the computer in the following order: command, parameter, and return code. After
processing the command from the computer, the projector sends a response code to the computer.
Command format
C1
C2
C3 C4
P1
P2
P3
Command 4-digit
Response code format
Normal response
O
K
P4
Return code (0DH)
Parameter 4-digit
Problem response (communication error or incorrect command)
E
Return code (0DH)
R
Return code (0DH)
R
Info
• If you are controlling the projector from a computer using RS-232C commands, wait at least 30 seconds
after turning the projector on before sending any commands.
• When more than one code is being sent, send each command only after the response code for the previous command from the projector is verified.
• When using the computer control function of the projector, the projector’s operating status cannot be read
by the computer. Therefore, confirm the status by transmitting the display commands for each adjustment
menu and checking the status with the on-screen display. If the projector receives a command other than a
menu display command, it will execute the command without displaying the on-screen display.
Commands
Example: To turn on the projector
Computer
P
O
W
R
_
_
1
_
Projector
→
←
O
K
RETURN
CONTROL CONTENTS
COMMAND
PARAMETER
_
_
Standby mode
(or 30-second startup time)
Power On
P
O
W
R
Power Off
P
O
W
R
_
_
_
0
OK or ERR
OK or ERR
T
L
P
S
_
_
_
1
0:OFF, 1:ON, 2:Re-try
3:Waiting, 4:Lamp Error
0:OFF, 4:Lamp Error
0:Normal,
1:Temp High,
2:Fan Error,
4:Lamp Cover Open,
8:Lamp Life 5% or less,
16:Lamp Burnt-out,
32:Lamp Ignition Failure,
64:Temp Abnormally High
0:Standby
Lamp Status
_
Power ON
1
OK or ERR
Projector Condition
T
A
B
N
_
_
_
1
0:Normal,
1:Temp High,
8:Lamp Life 5% or less,
16:Lamp Burnt-out,
32:Lamp Ignition Failure
Lamp Power Status
T
P
O
W
_
_
_
1
1:On, 2:Cooling 3:Shutting Down
Model Name Check
M
N
R
D
_
_
_
1
XV-Z21000
C1 (COMPONENT1)
OK
I
R
G
B
_
_
_
1
OK or ERR
ERR
C2 (COMPONENT2)
I
R
G
B
_
_
_
2
OK or ERR
ERR
S-VIDEO
I
V
E
D
_
_
_
1
OK or ERR
ERR
VIDEO
I
V
E
D
_
_
_
2
OK or ERR
ERR
DVI
I
R
G
B
_
_
_
3
OK or ERR
ERR
H1 (HDMI1)
I
R
G
B
_
_
_
4
OK or ERR
ERR
H2 (HDMI2)
I
R
G
B
_
_
_
5
OK or ERR
ERR
-52
RETURN
CONTROL CONTENTS
COMMAND
PARAMETER
INPUT Check
I
Freeze
Off
F
On
Auto Sync Start
C1 INPUT RESIZE
C2 INPUT RESIZE
S-VIDEO INPUT RESIZE
VIDEO INPUT RESIZE
DVI INPUT RESIZE
H1 INPUT RESIZE
H2 INPUT RESIZE
IRIS
Lamp Setting
C1 INPUT
C
H
K
?
?
?
Standby mode
(or 30-second startup time)
Power ON
?
1:COMPONENT1
2:COMPONENT2
3:S-VIDEO
4:VIDEO
5:DVI
6:HDMI1
7:HDMI2
ERR
R
E
Z
_
_
_
0
OK or ERR
ERR
F
R
E
Z
_
_
_
1
OK or ERR
ERR
A
D
J
S
_
_
_
1
OK or ERR
ERR
NORMAL
R
A
S
R
_
_
_
1
OK or ERR
ERR
STRETCH
R
A
S
R
_
_
_
2
OK or ERR
ERR
SIDE BAR/DOTBYDOT
R
A
S
R
_
_
_
3
OK or ERR
ERR
SMART STRETCH
R
A
S
R
_
_
_
4
OK or ERR
ERR
CINEMA ZOOM
R
A
S
R
_
_
_
5
OK or ERR
ERR
ZOOM 14:9
R
A
S
R
_
_
_
7
OK or ERR
ERR
SMART ZOOM
R
A
S
R
_
_
_
6
OK or ERR
ERR
NORMAL
R
B
S
R
_
_
_
1
OK or ERR
ERR
STRETCH
R
B
S
R
_
_
_
2
OK or ERR
ERR
SIDE BAR/DOTBYDOT
R
B
S
R
_
_
_
3
OK or ERR
ERR
SMART STRETCH
R
B
S
R
_
_
_
4
OK or ERR
ERR
CINEMA ZOOM
R
B
S
R
_
_
_
5
OK or ERR
ERR
ZOOM 14:9
R
B
S
R
_
_
_
7
OK or ERR
ERR
SMART ZOOM
R
B
S
R
_
_
_
6
OK or ERR
STRETCH
R
A
S
V
_
_
_
2
OK or ERR
ERR
SIDE BAR
R
A
S
V
_
_
_
3
OK or ERR
ERR
SMART STRETCH
R
A
S
V
_
_
_
4
OK or ERR
ERR
CINEMA ZOOM
R
A
S
V
_
_
_
5
OK or ERR
ERR
ZOOM 14:9
R
A
S
V
_
_
_
7
OK or ERR
ERR
SMART ZOOM
R
A
S
V
_
_
_
6
OK or ERR
ERR
ERR
STRETCH
R
B
S
V
_
_
_
2
OK or ERR
ERR
SIDE BAR
R
B
S
V
_
_
_
3
OK or ERR
ERR
SMART STRETCH
R
B
S
V
_
_
_
4
OK or ERR
ERR
CINEMA ZOOM
R
B
S
V
_
_
_
5
OK or ERR
ERR
ZOOM 14:9
R
B
S
V
_
_
_
7
OK or ERR
ERR
SMART ZOOM
R
B
S
V
_
_
_
6
OK or ERR
ERR
NORMAL
R
C
S
R
_
_
_
1
OK or ERR
ERR
STRETCH
R
C
S
R
_
_
_
2
OK or ERR
ERR
SIDE BAR/DOTBYDOT
R
C
S
R
_
_
_
3
OK or ERR
ERR
SMART STRETCH
R
C
S
R
_
_
_
4
OK or ERR
ERR
CINEMA ZOOM
R
C
S
R
_
_
_
5
OK or ERR
ERR
ZOOM 14:9
R
C
S
R
_
_
_
7
OK or ERR
ERR
SMART ZOOM
R
C
S
R
_
_
_
6
OK or ERR
ERR
NORMAL
R
D
S
R
_
_
_
1
OK or ERR
ERR
STRETCH
R
D
S
R
_
_
_
2
OK or ERR
ERR
SIDE BAR/DOTBYDOT
R
D
S
R
_
_
_
3
OK or ERR
ERR
SMART STRETCH
R
D
S
R
_
_
_
4
OK or ERR
ERR
CINEMA ZOOM
R
D
S
R
_
_
_
5
OK or ERR
ERR
ZOOM 14:9
R
D
S
R
_
_
_
7
OK or ERR
ERR
SMART ZOOM
R
D
S
R
_
_
_
6
OK or ERR
ERR
NORMAL
R
E
S
R
_
_
_
1
OK or ERR
ERR
STRETCH
R
E
S
R
_
_
_
2
OK or ERR
ERR
SIDE BAR/DOTBYDOT
R
E
S
R
_
_
_
3
OK or ERR
ERR
SMART STRETCH
R
E
S
R
_
_
_
4
OK or ERR
ERR
CINEMA ZOOM
R
E
S
R
_
_
_
5
OK or ERR
ERR
ZOOM 14:9
R
E
S
R
_
_
_
7
OK or ERR
ERR
SMART ZOOM
R
E
S
R
_
_
_
6
OK or ERR
ERR
High Brightness
I
R
I
S
_
_
_
1
OK or ERR
ERR
Medium Mode
I
R
I
S
_
_
_
2
OK or ERR
ERR
High Contrast
I
R
I
S
_
_
_
3
OK or ERR
ERR
Eco + Quiet
T
H
M
D
_
_
_
0
OK or ERR
ERR
Bright
T
H
M
D
_
_
_
1
OK or ERR
ERR
Standard
R
A
P
S
_
_
_
1
OK or ERR
ERR
Natural
R
A
P
S
_
_
_
2
OK or ERR
ERR
Dynamic
R
A
P
S
_
_
_
3
OK or ERR
ERR
Movie1
R
A
P
S
_
_
_
4
OK or ERR
ERR
Movie2
R
A
P
S
_
_
_
5
OK or ERR
ERR
Memory
ERR
Picture Mode
R
A
P
S
_
_
_
0
OK or ERR
Contrast (–90 — +90)
R
A
P
I
_
*
*
*
OK or ERR
ERR
Bright (–90 — +90)
R
A
B
R
_
*
*
*
OK or ERR
ERR
C
O
Color (–30 — +30)
R
A
Tint (–30 — +30)
R
A
T
I
_
*
*
*
OK or ERR
ERR
Sharp (-30 — +30)
R
A
S
H
_
*
*
*
OK or ERR
ERR
R
A
C
T
*
OK or ERR
ERR
CLR Temp *1
BrilliantColorTM
Gamma Position
Progressive
DNR
MNR
*
*
*
*
*
*
OK or ERR
ERR
Off
R
A
W
E
_
_
_
0
OK or ERR
ERR
On
R
A
W
E
_
_
_
1
OK or ERR
ERR
Standard
G
M
R
A
_
_
_
0
OK or ERR
ERR
Natural
G
M
R
A
_
_
_
1
OK or ERR
ERR
Dynamic
G
M
R
A
_
_
_
2
OK or ERR
ERR
Movie1
G
M
R
A
_
_
_
3
OK or ERR
ERR
Movie2
G
M
R
A
_
_
_
4
OK or ERR
ERR
Custom
G
M
R
A
_
_
_
5
OK or ERR
ERR
3D Fast
R
A
I
P
_
_
1
0
OK or ERR
ERR
3D Slow
R
A
I
P
_
_
1
1
OK or ERR
ERR
2D+
R
A
I
P
_
_
1
2
OK or ERR
ERR
Auto
R
A
F
M
_
_
_
0
OK or ERR
ERR
Off
R
A
F
M
_
_
_
1
OK or ERR
ERR
Off
R
A
N
R
_
_
_
0
OK or ERR
ERR
Level1
R
A
N
R
_
_
_
1
OK or ERR
ERR
Level2
R
A
N
R
_
_
_
2
OK or ERR
ERR
Level3
R
A
N
R
_
_
_
3
OK or ERR
Off
R
A
M
R
_
_
_
0
OK or ERR
ERR
Level1
R
A
M
R
_
_
_
1
OK or ERR
ERR
Level2
R
A
M
R
_
_
_
2
OK or ERR
ERR
Level3
R
A
M
R
_
_
_
3
OK or ERR
ERR
Appendix
Film Mode
_
ERR
-53
RETURN
CONTROL CONTENTS
C1 INPUT
Unveil Control
Automatic Contrast
COMMAND
Picture Mode
R
A
U
C
_
_
_
0
OK or ERR
ERR
Level1
R
A
U
C
_
_
_
1
OK or ERR
ERR
Level2
R
A
U
C
_
_
_
2
OK or ERR
ERR
Level3
R
A
U
C
_
_
_
3
OK or ERR
Off
R
A
A
C
_
_
_
0
OK or ERR
ERR
Level1
R
A
A
C
_
_
_
1
OK or ERR
ERR
Level2
R
A
A
C
_
_
_
2
OK or ERR
ERR
Level3
R
A
A
C
_
_
_
3
OK or ERR
ERR
R
A
R
E
_
_
_
1
OK or ERR
ERR
Standard
G
M
R
A
_
_
_
0
OK or ERR
ERR
R
B
P
S
_
_
_
2
OK or ERR
ERR
Dynamic
R
B
P
S
_
_
_
3
OK or ERR
ERR
R
B
P
S
_
_
_
4
OK or ERR
ERR
Movie2
R
B
P
S
_
_
_
5
OK or ERR
ERR
Memory
R
B
P
S
_
_
_
0
OK or ERR
ERR
Contrast (–90 — +90)
R
B
P
I
_
*
*
*
OK or ERR
ERR
Bright (–90 — +90)
R
B
B
R
_
*
*
*
OK or ERR
ERR
Color (–30 — +30)
R
B
C
O
_
*
*
*
OK or ERR
ERR
Tint (–30 — +30)
R
B
T
I
_
*
*
*
OK or ERR
ERR
Sharp (–30 — +30)
CLR Temp *1
BrilliantColorTM
Off
On
Gamma Position
Progressive
Film Mode
DNR
MNR
Unveil Control
Automatic Contrast
Picture Mode
R
B
S
H
*
OK or ERR
ERR
R
B
C
T
*
*
*
*
OK or ERR
ERR
R
B
W
E
_
_
_
0
OK or ERR
ERR
B
W
R
E
_
_
*
_
*
_
1
OK or ERR
ERR
Standard
G
M
R
B
_
_
_
0
OK or ERR
ERR
Natural
G
M
R
B
_
_
_
1
OK or ERR
ERR
Dynamic
G
M
R
B
_
_
_
2
OK or ERR
ERR
Movie1
G
M
R
B
_
_
_
3
OK or ERR
ERR
Movie2
G
M
R
B
_
_
_
4
OK or ERR
ERR
Custom
G
M
R
B
_
_
_
5
OK or ERR
ERR
3D Fast
R
B
I
P
_
_
1
0
OK or ERR
3D Slow
R
B
I
P
_
_
1
1
OK or ERR
ERR
2D+
R
B
I
P
_
_
1
2
OK or ERR
ERR
ERR
Auto
R
B
F
M
_
_
_
0
OK or ERR
ERR
Off
R
B
F
M
_
_
_
1
OK or ERR
ERR
Off
R
B
N
R
_
_
_
0
OK or ERR
ERR
Level1
R
B
N
R
_
_
_
1
OK or ERR
ERR
Level2
R
B
N
R
_
_
_
2
OK or ERR
ERR
Level3
R
B
N
R
_
_
_
3
OK or ERR
ERR
Off
R
B
M
R
_
_
_
0
OK or ERR
ERR
Level1
R
B
M
R
_
_
_
1
OK or ERR
ERR
Level2
R
B
M
R
_
_
_
2
OK or ERR
ERR
Level3
R
B
M
R
_
_
_
3
OK or ERR
ERR
Off
R
B
U
C
_
_
_
0
OK or ERR
ERR
Level1
R
B
U
C
_
_
_
1
OK or ERR
ERR
Level2
R
B
U
C
_
_
_
2
OK or ERR
ERR
Level3
R
B
U
C
_
_
_
3
OK or ERR
ERR
Off
R
B
A
C
_
_
_
0
OK or ERR
ERR
Level1
R
B
A
C
_
_
_
1
OK or ERR
ERR
Level2
R
B
A
C
_
_
_
2
OK or ERR
ERR
Level3
R
B
A
C
_
_
_
3
OK or ERR
ERR
R
B
R
E
_
_
_
1
OK or ERR
ERR
Picture Reset
Standard
V
A
P
S
_
_
_
1
OK or ERR
ERR
Natural
V
A
P
S
_
_
_
2
OK or ERR
ERR
Dynamic
V
A
P
S
_
_
_
3
OK or ERR
ERR
Movie1
V
A
P
S
_
_
_
4
OK or ERR
ERR
Movie2
V
A
P
S
_
_
_
5
OK or ERR
ERR
Memory
V
A
P
S
_
_
_
0
OK or ERR
ERR
Contrast (–90 — +90)
V
A
P
I
_
*
*
*
OK or ERR
ERR
Bright (–90 — +90)
V
A
B
R
_
*
*
*
OK or ERR
ERR
Color (–30 — +30)
V
A
C
O
_
*
*
*
OK or ERR
ERR
Tint (–30 — +30)
V
A
T
I
_
*
*
*
OK or ERR
ERR
Sharp (–30 — +30)
CLR Temp *1
BrilliantColorTM
Off
On
Gamma Position
Progressive
Film Mode
DNR
MNR
Unveil Control
Automatic Contrast
Picture Reset
-54
ERR
Natural
Movie1
S-VIDEO INPUT
Standby mode
(or 30-second startup time)
Power ON
Off
Picture Reset
C2 INPUT
PARAMETER
V
A
S
H
*
OK or ERR
ERR
V
A
C
T
*
*
*
*
OK or ERR
ERR
V
A
W
E
_
_
_
0
OK or ERR
ERR
A
W
V
E
_
_
*
_
*
_
1
OK or ERR
ERR
Standard
G
M
V
A
_
_
_
0
OK or ERR
ERR
Natural
G
M
V
A
_
_
_
1
OK or ERR
ERR
Dynamic
G
M
V
A
_
_
_
2
OK or ERR
ERR
Movie1
G
M
V
A
_
_
_
3
OK or ERR
ERR
Movie2
G
M
V
A
_
_
_
4
OK or ERR
ERR
Custom
G
M
V
A
_
_
_
5
OK or ERR
ERR
3D Fast
V
A
I
P
_
_
1
0
OK or ERR
ERR
3D Slow
V
A
I
P
_
_
1
1
OK or ERR
ERR
2D+
V
A
I
P
_
_
1
2
OK or ERR
ERR
Auto
V
A
F
M
_
_
_
0
OK or ERR
ERR
Off
V
A
F
M
_
_
_
1
OK or ERR
ERR
Off
V
A
N
R
_
_
_
0
OK or ERR
ERR
Level1
V
A
N
R
_
_
_
1
OK or ERR
ERR
Level2
V
A
N
R
_
_
_
2
OK or ERR
ERR
Level3
V
A
N
R
_
_
_
3
OK or ERR
ERR
Off
V
A
M
R
_
_
_
0
OK or ERR
ERR
Level1
V
A
M
R
_
_
_
1
OK or ERR
ERR
Level2
V
A
M
R
_
_
_
2
OK or ERR
ERR
Level3
V
A
M
R
_
_
_
3
OK or ERR
ERR
Off
V
A
U
C
_
_
_
0
OK or ERR
ERR
Level1
V
A
U
C
_
_
_
1
OK or ERR
ERR
Level2
V
A
U
C
_
_
_
2
OK or ERR
ERR
Level3
V
A
U
_
3
OK or ERR
ERR
C
_
_
Off
V
A
A
C
_
_
_
0
OK or ERR
ERR
Level1
V
A
A
C
_
_
_
1
OK or ERR
ERR
Level2
V
A
A
C
_
_
_
2
OK or ERR
ERR
Level3
V
A
A
C
_
_
_
3
OK or ERR
ERR
V
A
R
E
_
_
_
1
OK or ERR
ERR
RETURN
CONTROL CONTENTS
VIDEO INPUT
Picture Mode
COMMAND
V
B
P
S
_
_
_
1
OK or ERR
ERR
Natural
V
B
P
S
_
_
_
2
OK or ERR
ERR
Dynamic
V
B
P
S
_
_
_
3
OK or ERR
ERR
Movie1
V
B
P
S
_
_
_
4
OK or ERR
ERR
Movie2
V
B
P
S
_
_
_
5
OK or ERR
ERR
Memory
V
B
P
S
_
_
_
0
OK or ERR
ERR
Contrast (–90 — +90)
V
B
P
I
_
*
*
*
OK or ERR
ERR
Bright (–90 — +90)
V
B
B
R
_
*
*
*
OK or ERR
ERR
Color (–30 — +30)
V
B
C
O
_
*
*
*
OK or ERR
ERR
Tint (–30 — +30)
V
B
T
I
_
*
*
*
OK or ERR
ERR
Sharp (–30 — +30)
V
B
S
H
_
*
*
*
OK or ERR
ERR
C
T
*
OK or ERR
ERR
CLR Temp *1
Gamma Position
Progressive
Film Mode
DNR
MNR
Unveil Control
Automatic Contrast
V
Picture Mode
B
*
*
*
Off
V
B
W
E
_
_
_
0
OK or ERR
ERR
On
V
B
W
E
_
_
_
1
OK or ERR
ERR
Standard
G
M
V
B
_
_
_
0
OK or ERR
ERR
Natural
G
M
V
B
_
_
_
1
OK or ERR
ERR
Dynamic
G
M
V
B
_
_
_
2
OK or ERR
ERR
Movie1
G
M
V
B
_
_
_
3
OK or ERR
ERR
Movie2
G
M
V
B
_
_
_
4
OK or ERR
ERR
Custom
G
M
V
B
_
_
_
5
OK or ERR
ERR
3D Fast
V
B
I
P
_
_
1
0
OK or ERR
ERR
3D Slow
V
B
I
P
_
_
1
1
OK or ERR
ERR
2D+
V
B
P
_
_
1
2
OK or ERR
ERR
I
Auto
V
B
F
M
_
_
_
0
OK or ERR
ERR
Off
V
B
F
M
_
_
_
1
OK or ERR
ERR
Off
V
B
N
R
_
_
_
0
OK or ERR
ERR
Level1
V
B
N
R
_
_
_
1
OK or ERR
ERR
Level2
V
B
N
R
_
_
_
2
OK or ERR
ERR
Level3
V
B
_
3
OK or ERR
ERR
N
R
_
_
Off
V
B
M
R
_
_
_
0
OK or ERR
ERR
Level1
V
B
M
R
_
_
_
1
OK or ERR
ERR
Level2
V
B
M
R
_
_
_
2
OK or ERR
ERR
Level3
V
B
M
R
_
_
_
3
OK or ERR
ERR
Off
V
B
U
C
_
_
_
0
OK or ERR
ERR
Level1
V
B
U
C
_
_
_
1
OK or ERR
ERR
Level2
V
B
U
C
_
_
_
2
OK or ERR
ERR
Level3
V
B
U
C
_
_
_
3
OK or ERR
ERR
Off
V
B
A
C
_
_
_
0
OK or ERR
ERR
Level1
V
B
A
C
_
_
_
1
OK or ERR
ERR
Level2
V
B
A
C
_
_
_
2
OK or ERR
ERR
Level3
V
B
A
C
_
_
_
3
OK or ERR
ERR
V
B
R
E
_
_
_
1
OK or ERR
Picture Reset
ERR
Standard
R
C
P
S
_
_
_
1
OK or ERR
ERR
Natural
R
C
P
S
_
_
_
2
OK or ERR
ERR
Dynamic
R
C
P
S
_
_
_
3
OK or ERR
ERR
Movie1
R
C
P
S
_
_
_
4
OK or ERR
ERR
Movie2
R
C
P
S
_
_
_
5
OK or ERR
ERR
Memory
R
C
P
S
_
_
_
0
OK or ERR
ERR
Contrast (–90 — +90)
R
C
P
I
_
*
*
*
OK or ERR
ERR
Bright (–90 — +90)
R
C
B
R
_
*
*
*
OK or ERR
ERR
Color (–30 — +30)
R
C
C
O
_
*
*
*
OK or ERR
ERR
Tint (–30 — +30)
R
C
T
I
_
*
*
*
OK or ERR
ERR
Sharp (–30 — +30)
R
C
S
H
_
*
*
*
OK or ERR
ERR
R
C
C
T
*
*
*
*
OK or ERR
ERR
R
C
W
E
_
_
_
0
OK or ERR
ERR
ERR
CLR Temp *1
BrilliantColorTM
Gamma Position
Progressive
Film Mode
DNR
MNR
Unveil Control
Automatic Contrast
Off
On
R
C
W
E
_
_
_
1
OK or ERR
Standard
G
M
R
C
_
_
_
0
OK or ERR
ERR
Natural
G
M
R
C
_
_
_
1
OK or ERR
ERR
Dynamic
G
M
R
C
_
_
_
2
OK or ERR
ERR
Movie1
G
M
R
C
_
_
_
3
OK or ERR
ERR
Movie2
G
M
R
C
_
_
_
4
OK or ERR
ERR
Custom
G
M
R
C
_
_
_
5
OK or ERR
ERR
3D Fast
R
C
I
P
_
_
1
0
OK or ERR
ERR
3D Slow
R
C
I
P
_
_
1
1
OK or ERR
ERR
2D+
R
C
P
_
_
1
2
OK or ERR
ERR
R
C
F
M
_
_
_
0
OK or ERR
ERR
R
C
F
M
_
_
_
1
OK or ERR
ERR
Off
R
C
N
R
_
_
_
0
OK or ERR
ERR
Level1
R
C
N
R
_
_
_
1
OK or ERR
ERR
Level2
R
C
N
R
_
_
_
2
OK or ERR
ERR
Level3
R
C
N
R
_
_
_
3
OK or ERR
ERR
Off
R
C
M
R
_
_
_
0
OK or ERR
ERR
Level1
R
C
M
R
_
_
_
1
OK or ERR
ERR
Level2
R
C
M
R
_
_
_
2
OK or ERR
ERR
Level3
R
C
M
R
_
_
_
3
OK or ERR
Off
R
C
U
C
_
_
_
0
OK or ERR
ERR
Level1
R
C
U
C
_
_
_
1
OK or ERR
ERR
Level2
R
C
U
C
_
_
_
2
OK or ERR
ERR
Level3
R
C
U
C
_
_
_
3
OK or ERR
ERR
Off
R
C
A
C
_
_
_
0
OK or ERR
ERR
Level1
R
C
A
C
_
_
_
1
OK or ERR
ERR
Level2
R
C
A
C
_
_
_
2
OK or ERR
ERR
Level3
R
C
A
C
_
_
_
3
OK or ERR
ERR
R
C
R
E
_
_
_
1
OK or ERR
ERR
ERR
Standard
R
D
P
S
_
_
_
1
OK or ERR
ERR
Natural
R
D
P
S
_
_
_
2
OK or ERR
ERR
Dynamic
R
D
P
S
_
_
_
3
OK or ERR
ERR
Movie1
R
D
P
S
_
_
_
4
OK or ERR
ERR
Movie2
R
D
P
S
_
_
_
5
OK or ERR
ERR
Memory
R
D
P
S
_
_
_
0
OK or ERR
ERR
Contrast (–90 — +90)
R
D
P
I
_
*
*
*
OK or ERR
ERR
Bright (–90 — +90)
R
D
B
R
_
*
*
*
OK or ERR
ERR
Color (–30 — +30)
R
D
C
O
_
*
*
*
OK or ERR
ERR
Appendix
Picture Mode
I
Auto
Off
Picture Reset
H1 INPUT
Standby mode
(or 30-second startup time)
Power ON
Standard
BrilliantColorTM
DVI INPUT
PARAMETER
-55
RETURN
CONTROL CONTENTS
H1 INPUT
COMMAND
Tint (–30 — +30)
R
T
I
_
*
*
Standby mode
(or 30-second startup time)
Power ON
*
OK or ERR
ERR
Sharp (–30 — +30)
R
D
S
H
_
*
*
*
OK or ERR
ERR
CLR Temp *1
R
D
C
T
*
*
*
*
OK or ERR
ERR
TM
BrilliantColor
Gamma Position
Progressive
Film Mode
DNR
MNR
Unveil Control
Automatic Contrast
Off
D
W
E
_
_
_
0
OK or ERR
ERR
On
R
D
W
E
_
_
_
1
OK or ERR
ERR
Standard
G
M
R
D
_
_
_
0
OK or ERR
ERR
Natural
G
M
R
D
_
_
_
1
OK or ERR
ERR
Dynamic
G
M
R
D
_
_
_
2
OK or ERR
ERR
Movie1
G
M
R
D
_
_
_
3
OK or ERR
ERR
Movie2
G
M
R
D
_
_
_
4
OK or ERR
ERR
Custom
G
M
R
D
_
_
_
5
OK or ERR
ERR
3D Fast
R
D
I
P
_
_
1
0
OK or ERR
Picture Mode
R
ERR
3D Slow
R
D
I
P
_
_
1
1
OK or ERR
ERR
2D+
R
D
I
P
_
_
1
2
OK or ERR
ERR
Auto
R
D
F
M
_
_
_
0
OK or ERR
ERR
Off
R
D
F
M
_
_
_
1
OK or ERR
ERR
Off
R
D
N
R
_
_
_
0
OK or ERR
ERR
Level1
R
D
N
R
_
_
_
1
OK or ERR
ERR
Level2
R
D
N
R
_
_
_
2
OK or ERR
ERR
Level3
R
D
N
R
_
_
_
3
OK or ERR
ERR
Off
R
D
M
R
_
_
_
0
OK or ERR
ERR
Level1
R
D
M
R
_
_
_
1
OK or ERR
ERR
Level2
R
D
M
R
_
_
_
2
OK or ERR
ERR
Level3
R
D
M
R
_
_
_
3
OK or ERR
ERR
Off
R
D
U
C
_
_
_
0
OK or ERR
ERR
Level1
R
D
U
C
_
_
_
1
OK or ERR
ERR
Level2
R
D
U
C
_
_
_
2
OK or ERR
ERR
Level3
R
D
U
C
_
_
_
3
OK or ERR
ERR
Off
R
D
A
C
_
_
_
0
OK or ERR
ERR
Level1
R
D
A
C
_
_
_
1
OK or ERR
ERR
Level2
R
D
A
C
_
_
_
2
OK or ERR
ERR
Level3
R
ERR
D
A
C
_
_
_
3
OK or ERR
R
D
R
E
_
_
_
1
OK or ERR
Standard
R
E
P
S
_
_
_
1
OK or ERR
ERR
Natural
R
E
P
S
_
_
_
2
OK or ERR
ERR
Dynamic
R
E
P
S
_
_
_
3
OK or ERR
ERR
Movie1
R
E
P
S
_
_
_
4
OK or ERR
ERR
Movie2
R
E
P
S
_
_
_
5
OK or ERR
ERR
Memory
ERR
Picture Reset
H2 INPUT
D
PARAMETER
ERR
R
E
P
S
_
_
_
0
OK or ERR
Contrast (–90 — +90)
R
E
P
I
_
*
*
*
OK or ERR
ERR
Bright (–90 — +90)
R
E
B
R
_
*
*
*
OK or ERR
ERR
C
Color (–30 — +30)
R
E
O
_
*
*
*
OK or ERR
ERR
Tint (–30 — +30)
R
E
T
I
_
*
*
*
OK or ERR
ERR
Sharp (–30 — +30)
R
E
S
H
_
*
*
*
OK or ERR
ERR
R
E
C
T
*
OK or ERR
ERR
CLR Temp *1
BrilliantColorTM
Gamma Position
Progressive
Film Mode
DNR
MNR
Unveil Control
Automatic Contrast
*
*
*
Off
R
E
W
E
_
_
_
0
OK or ERR
ERR
On
R
E
W
E
_
_
_
1
OK or ERR
ERR
Standard
G
M
R
Z
_
_
_
0
OK or ERR
ERR
Natural
G
M
R
Z
_
_
_
1
OK or ERR
ERR
Dynamic
G
M
R
Z
_
_
_
2
OK or ERR
ERR
Movie1
G
M
R
Z
_
_
_
3
OK or ERR
ERR
Movie2
G
M
R
Z
_
_
_
4
OK or ERR
ERR
Custom
G
M
R
Z
_
_
_
5
OK or ERR
ERR
3D Fast
R
E
I
P
_
_
1
0
OK or ERR
ERR
3D Slow
R
E
I
P
_
_
1
1
OK or ERR
ERR
2D+
R
E
P
_
_
1
2
OK or ERR
ERR
I
Auto
R
E
F
M
_
_
_
0
OK or ERR
ERR
Off
R
E
F
M
_
_
_
1
OK or ERR
ERR
Off
R
E
N
R
_
_
_
0
OK or ERR
ERR
Level1
R
E
N
R
_
_
_
1
OK or ERR
ERR
Level2
R
E
N
R
_
_
_
2
OK or ERR
ERR
Level3
R
E
N
R
_
_
_
3
OK or ERR
Off
R
E
M
R
_
_
_
0
OK or ERR
ERR
Level1
R
E
M
R
_
_
_
1
OK or ERR
ERR
Level2
R
E
M
R
_
_
_
2
OK or ERR
ERR
Level3
R
E
M
R
_
_
_
3
OK or ERR
ERR
Off
R
E
U
C
_
_
_
0
OK or ERR
ERR
Level1
R
E
U
C
_
_
_
1
OK or ERR
ERR
Level2
R
E
U
C
_
_
_
2
OK or ERR
ERR
Level3
R
E
U
C
_
_
_
3
OK or ERR
ERR
Off
R
E
A
C
_
_
_
0
OK or ERR
ERR
Level1
R
E
A
C
_
_
_
1
OK or ERR
ERR
Level2
R
E
A
C
_
_
_
2
OK or ERR
ERR
Level3
E
A
C
_
_
_
3
OK or ERR
ERR
R
E
R
E
_
_
_
1
OK or ERR
ERR
All Colors-Gamma (–10 — +10)
G
M
E
W
_
*
*
*
OK or ERR
ERR
Red-Gamma (–30 — +30)
G
M
E
R
_
*
*
*
OK or ERR
ERR
Picture Reset
R
ERR
Green-Gamma (–30 — +30)
G
M
G
_
*
*
*
OK or ERR
ERR
Blue-Gamma (–30 — +30)
G
M
E
B
_
*
*
*
OK or ERR
ERR
All Colors-White Detail (–10 — +10)
G
M
G
E
W
_
*
*
*
OK or ERR
ERR
Red-White Detail (–30 — +30)
G
M
G
R
_
*
*
*
OK or ERR
ERR
Green-White Detail (–30 — +30)
G
M
G
_
*
*
*
OK or ERR
ERR
Blue-White Detail (–30 — +30)
G
M
G
B
_
*
*
*
OK or ERR
ERR
All Colors-Black Detail (–10 — +10)
G
M
O
W
_
*
*
*
OK or ERR
G
ERR
Red-Black Detail (–30 — +30)
G
M
O
R
_
*
*
*
OK or ERR
ERR
Green-Black Detail (–30 — +30)
G
M
O
G
_
*
*
*
OK or ERR
ERR
Blue-Black Detail (–30 — +30)
G
M
O
B
_
*
*
*
OK or ERR
ERR
Gamma Reset
G
M
R
E
_
_
_
1
OK or ERR
ERR
C.M.S. R-Hue (–30 — +30)
C
M
H
R
_
*
*
*
OK or ERR
ERR
C.M.S. Y-Hue (–30 — +30)
C
M
H
Y
_
*
*
*
OK or ERR
ERR
C.M.S. G-Hue (–30 — +30)
C
M
H
G
_
*
*
*
OK or ERR
ERR
C.M.S. C-Hue (–30 — +30)
C
M
H
C
_
*
*
*
OK or ERR
ERR
C.M.S. B-Hue (–30 — +30)
C
M
H
B
_
*
*
*
OK or ERR
ERR
-56
RETURN
CONTROL CONTENTS
COMMAND
C.M.S. M-Hue (–30 — +30)
C
M
H
C.M.S. Hue Reset
C
M
C.M.S. R-Saturation (–30 — +30)
C
M
PARAMETER
Standby mode
(or 30-second startup time)
Power ON
M
_
*
*
*
OK or ERR
ERR
R
E
_
_
_
2
OK or ERR
ERR
S
R
_
*
*
*
OK or ERR
ERR
C.M.S. Y-Saturation (–30 — +30)
C
M
S
Y
_
*
*
*
OK or ERR
ERR
C.M.S. G-Saturation (–30 — +30)
C
M
S
G
_
*
*
*
OK or ERR
ERR
C.M.S. C-Saturation (–30 — +30)
C
M
S
C
_
*
*
*
OK or ERR
ERR
C.M.S. B-Saturation (–30 — +30)
S
B
C.M.S. M-Saturation (–30 — +30)
C
M
S
M
_
*
*
*
OK or ERR
ERR
C.M.S. Saturation Reset
C
C
M
M
R
E
_
_
_
*
_
*
3
*
OK or ERR
OK or ERR
ERR
ERR
C.M.S. R-Value (–30 — +30)
C
M
V
R
_
*
*
*
OK or ERR
ERR
C.M.S. Y-Value (–30 — +30)
C
M
V
Y
_
*
*
*
OK or ERR
ERR
C.M.S. G-Value (–30 — +30)
C
M
V
G
_
*
*
*
OK or ERR
ERR
C.M.S. C-Value (–30 — +30)
C
M
V
C
_
*
*
*
OK or ERR
ERR
C.M.S. B-Value (–30 — +30)
C
M
V
B
_
*
*
*
OK or ERR
ERR
C.M.S. M-Value (–30 — +30)
C
M
V
M
_
*
*
*
OK or ERR
ERR
C.M.S. Value Reset
C
M
R
E
_
_
_
4
OK or ERR
ERR
C.M.S. All Reset
C
M
R
E
_
_
_
1
OK or ERR
ERR
Clock (–150 — +150)
I
N
C
L
*
*
*
*
OK or ERR
ERR
Phase (–60 — +60)
I
N
P
H
_
*
*
*
OK or ERR
ERR
A
H-Pos (–150 — +150)
H
P
V-Pos (–60 — +60)
I
A
V
P
_
*
*
*
OK or ERR
ERR
Fine Reset
I
I
A
R
E
_
_
_
1
OK or ERR
ERR
RGB Horizontal Frequency Check
F
_
*
_
*
_
*
1
OK or ERR
OK or ERR
ERR
R
Q
RGB Vertical Frequency Check
T
F
R
Q
_
_
_
2
OK or ERR
ERR
Auto Sync
A
A
D
J
_
_
_
0
OK or ERR
ERR
Off
T
*
ERR
Normal
A
A
D
J
_
_
_
1
OK or ERR
ERR
High Speed
A
A
D
J
_
_
_
2
OK or ERR
ERR
Image Shift (–30 — +30)
S
T
S
H
_
*
*
*
OK or ERR
Subtitle (–30 — +30)
S
T
S
Z
_
*
*
*
OK or ERR
ERR
Overscan (10% — 0%) *2
O
V
S
N
_
*
*
*
OK or ERR
ERR
Options Reset
O
P
R
E
_
_
_
1
OK or ERR
ERR
C1 White Level (–30 — +30)
R
A
I
G
_
*
*
*
OK or ERR
ERR
C2 White Level (–30 — +30)
R
B
I
G
_
*
*
*
OK or ERR
ERR
S-Video White Level (–30 — +30)
V
A
I
G
_
*
*
*
OK or ERR
ERR
Video White Level (–30 — +30)
V
B
I
G
_
*
*
*
OK or ERR
ERR
DVI White Level (–30 — +30)
R
C
I
G
_
*
*
*
OK or ERR
ERR
C1 Black Level (–30 — +30)
R
A
I
O
_
*
*
*
OK or ERR
ERR
C2 Black Level (–30 — +30)
R
B
I
O
_
*
*
*
OK or ERR
S-Video Black Level (–30 — +30)
V
A
I
O
_
*
*
*
OK or ERR
ERR
Video Black Level (–30 — +30)
V
B
I
O
_
*
*
*
OK or ERR
ERR
DVI Black Level (–30 — +30)
R
C
I
O
LED
Signal Type
C2 INPUT
Signal Type
DVI INPUT
Signal Type
H1 INPUT
Signal Type
H2 INPUT
Signal Type
H1 INPUT
Color Space
H2 INPUT
Color Space
DVI INPUT
Dynamic Range
H1 INPUT
Dynamic Range
H2 INPUT
Dynamic Range
OK or ERR
ERR
E
D
S
_
_
_
0
OK or ERR
ERR
E
D
S
_
_
_
1
OK or ERR
ERR
_
_
_
1
0 - 9999(Integer)
T
T
T
L
T
L
_
_
_
1
0% – 100% (Integer)
Off
T
I
M
D
I
_
_
_
0
OK or ERR
ERR
On
I
M
D
I
_
_
_
1
OK or ERR
ERR
Auto
I
A
S
I
_
_
_
0
OK or ERR
ERR
L
RGB
I
A
S
I
_
_
_
1
OK or ERR
ERR
Component
I
A
S
I
_
_
_
2
OK or ERR
ERR
Auto
I
B
S
I
_
_
_
0
OK or ERR
ERR
RGB
I
B
S
I
_
_
_
1
OK or ERR
ERR
Component
I
B
S
I
_
_
_
2
OK or ERR
ERR
D. PC RGB
I
C
S
I
_
_
_
3
OK or ERR
D. PC COMP.
I
C
S
I
_
_
_
4
OK or ERR
ERR
D. VIDEO RGB
I
C
S
I
_
_
_
5
OK or ERR
ERR
D. VIDEO COMP.
I
C
S
I
_
_
_
6
OK or ERR
ERR
A. RGB
I
C
S
I
_
_
_
1
OK or ERR
A. COMP.
I
C
S
I
_
_
_
2
OK or ERR
ERR
Auto
I
D
S
I
_
_
_
0
OK or ERR
ERR
ERR
ERR
RGB
I
D
S
I
_
_
_
1
OK or ERR
ERR
YCbCr4:4:4
I
D
S
I
_
_
_
7
OK or ERR
ERR
YCbCr4:4:2
I
D
S
I
_
_
_
8
OK or ERR
ERR
Auto
I
E
S
I
_
_
_
0
OK or ERR
ERR
RGB
I
E
S
I
_
_
_
1
OK or ERR
ERR
YCbCr4:4:4
I
E
S
I
_
_
_
7
OK or ERR
ERR
YCbCr4:4:2
I
E
S
I
_
_
_
8
OK or ERR
ERR
Auto
H
M
D
C
_
_
_
0
OK or ERR
ERR
ITU601
H
M
D
C
_
_
_
1
OK or ERR
ERR
ITU709
H
M
D
C
_
_
_
2
OK or ERR
ERR
Auto
H
M
E
C
_
_
_
0
OK or ERR
ERR
ITU601
H
M
E
C
_
_
_
1
OK or ERR
ERR
ITU709
H
M
E
C
_
_
_
2
OK or ERR
ERR
Auto
H
M
C
D
_
_
_
0
OK or ERR
ERR
Standard
H
M
C
D
_
_
_
1
OK or ERR
ERR
Enhanced
H
M
C
D
_
_
_
2
OK or ERR
ERR
M
D
D
_
_
_
0
OK or ERR
ERR
Auto
H
Standard
H
M
D
D
_
_
_
1
OK or ERR
ERR
Enhanced
H
M
D
D
_
_
_
2
OK or ERR
ERR
Auto
H
M
E
D
_
_
_
0
OK or ERR
ERR
Standard
H
M
E
D
_
_
_
1
OK or ERR
ERR
Enhanced
H
M
E
D
_
_
_
2
OK or ERR
ERR
Auto
M
E
S
Y
_
_
_
1
OK or ERR
ERR
PAL
M
E
S
Y
_
_
_
2
OK or ERR
ERR
SECAM
M
E
S
Y
_
_
_
3
OK or ERR
ERR
NTSC4.43
Background
*
L
L
M
E
S
Y
_
_
_
4
OK or ERR
ERR
NTSC3.58
M
E
S
Y
_
_
_
5
OK or ERR
ERR
PAL-M
M
E
S
Y
_
_
_
6
OK or ERR
ERR
PAL-N
M
E
S
Y
_
_
_
7
OK or ERR
ERR
PAL-60
M
Y
_
_
_
8
OK or ERR
ERR
E
S
Appendix
Video System
*
Off
Lamp Life (Percentage)
C1 INPUT
*
ERR
On
Lamp Usage Time (Hour)
OSD Display
_
ERR
Logo
I
M
B
G
_
_
_
1
OK or ERR
ERR
Blue
I
M
B
G
_
_
_
3
OK or ERR
ERR
None
I
M
B
G
_
_
_
4
OK or ERR
ERR
-57
RETURN
CONTROL CONTENTS
RS232C Port
Off
Auto Power Off
Fan Mode
PRJ Mode
L
N
On
L
N
Off
A
P
On
A
P
Normal
H
L
High
R
PARAMETER
Standby mode
(or 30-second startup time)
Power ON
S
_
_
_
0
OK or ERR
ERR
R
S
_
_
_
1
OK or ERR
ERR
O
W
_
_
_
0
OK or ERR
ERR
O
W
_
_
_
1
OK or ERR
ERR
M
D
_
_
_
0
OK or ERR
ERR
ERR
H
L
M
D
_
_
_
1
OK or ERR
Front
I
M
R
E
_
_
_
0
OK or ERR
Ceiling + Front
I
M
R
E
_
_
_
1
OK or ERR
ERR
Rear
I
M
I
N
_
_
_
0
OK or ERR
ERR
Rear + Front
I
M
I
N
_
_
_
1
OK or ERR
ERR
A
L
R
E
_
_
_
1
OK or ERR
ERR
English
M
E
L
A
_
_
_
1
OK or ERR
ERR
Deutsch
M
E
L
A
_
_
_
2
OK or ERR
ERR
Español
M
E
L
A
_
_
_
3
OK or ERR
ERR
Nederlands
M
E
L
A
_
_
_
4
OK or ERR
ERR
Français
M
E
L
A
_
_
_
5
OK or ERR
ERR
Italiano
M
E
L
A
_
_
_
6
OK or ERR
Svenska
M
E
L
A
_
_
_
7
OK or ERR
ERR
M
E
L
A
_
_
_
8
OK or ERR
ERR
All reset
Language
COMMAND
Português
Lamp Quantity
ERR
ERR
M
E
L
A
_
_
_
9
OK or ERR
ERR
M
E
L
A
_
_
1
0
OK or ERR
ERR
M
E
L
A
_
_
1
1
OK or ERR
ERR
T
L
P
N
_
_
_
1
“1”
Model Name Check
T
N
A
M
_
_
_
1
XV-Z21000
Projector Name Setting
P
J
N
0
_
_
_
1
Projector Name Setting 1 (First four characters) *3
P
J
N
1
*
*
*
*
OK or ERR
ERR
Projector Name Setting 2 (Middle four characters) *3
P
J
N
2
*
*
*
*
OK or ERR
ERR
Projector Name Setting 3 (Last four characters) *3
P
J
N
3
*
*
*
*
OK or ERR
ERR
Lamp Timer Reset *4
L
P
R
E
_
_
_
1
ERR
OK or ERR
Note
• If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value
in the range indicated in brackets under CONTROL CONTENTS.
• Fine Sync can only be set in the displayed RGB mode.
• The return value of “TLTT_ _ _1” becomes “0” when the projector is in the standby mode.
*1
The command parameters for the CLR temperature setting are as follows.
Parameter
5500
6500
7500
8500
9500
10500
*2
_055
_065
_075
_085
_095
_105
The command parameters for the Overscan setting are as follows.
Parameter
10%
9%
8%
7%
6%
5%
4%
3%
2%
1%
0%
*3
*4
__10
___9
___8
___7
___6
___5
___4
___3
___2
___1
___0
For setting the projector name, send the commands in order of PJN1, PJN2 and PJN3.
The Lamp Timer Reset command can only be sent in standby mode.
-58
Wired Remote Control Terminal Specifications
Specifications of wired remote control input
• ø3.5 mm minijack
• External: GND
• Internal: +3.3V
Function and transmission codes
CONTROL
ITEM
SYSTEM CODE
JUDGEMENT
CODE
DATA CODE
C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14
SYSTEM CODE
CONTROL
ITEM
C15
JUDGEMENT
CODE
DATA CODE
C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14
C15
ON
1
0
1
1
0
0
1
1
0
1
0
1
0
1
0
RESIZE
1
0
1
1
0
0
1
1
1
1
0
1
0
1
0
STANDBY
1
0
1
1
0
0
1
1
0
1
0
0
1
1
0
PICTURE MODE
1
0
1
1
0
1
0
0
1
1
1
0
0
1
0
MENU
1
0
1
1
0
0
0
1
0
0
0
1
1
1
0
IRIS
1
0
1
1
0
0
1
0
1
0
1
0
1
1
0
'
1
0
1
1
0
0
0
1
1
1
0
0
1
1
0
AUTO SYNC
1
0
1
1
0
0
1
0
1
1
1
1
1
1
0
"
1
0
1
1
0
1
0
1
1
1
0
0
1
1
0
FREEZE
1
0
1
1
0
1
0
1
1
0
0
0
1
1
0
\
1
0
1
1
0
0
0
0
0
1
0
1
0
1
0
COMPONENT1 1
0
1
1
0
0
1
0
1
1
0
0
0
1
0
|
1
0
1
1
0
1
1
1
1
0
0
1
0
1
0
COMPONENT2 1
0
1
1
0
0
1
0
1
1
1
0
0
1
0
ENTER
1
0
1
1
0
1
1
1
0
1
0
1
0
1
0
S-VIDEO
1
0
1
1
0
1
1
1
0
1
1
0
0
1
0
RETURN
1
0
1
1
0
1
0
0
1
1
0
1
0
1
0
VIDEO
1
0
1
1
0
0
1
0
0
1
1
0
0
1
0
RGB/COMP.
1
0
1
1
0
1
0
0
0
1
1
1
1
1
0
DVI
1
0
1
1
0
1
0
1
0
1
1
0
0
1
0
CONTRAST
1
0
1
1
1
0
1
0
0
0
1
0
0
1
0
HDMI1
1
0
1
1
0
0
1
1
0
1
1
0
0
1
0
BRIGHT
1
0
1
1
1
1
0
0
1
0
1
0
0
1
0
HDMI2
1
0
1
1
0
1
0
1
0
1
1
0
1
1
0
INPUT
1
0
1
1
0
1
1
0
0
1
0
0
0
1
0
Wired remote control function code
LSB
C1
1
System Code
C5
C6
1
0
*
0
1
MSB
Data Code
*
*
*
*
*
*
C13
C14
C15
*
1
0
• System codes C1 to C5 are fixed at “10110”.
• Codes C14 and C15 are reverse confirmation bits, with “10” indicating “Front” and “01” indicating “Rear”.
Sharp remote control signal format
Transmission format: 15-bit format
D
D
D
D
D
D
67.5 ms
D
D
D
D
D
D
D
67.5 ms
Wave form of output signal: Output using pulse position modulation
t
T1
T0
“1”
“0”
26.4 s
“0”
“0”
“0”
“1”
t
“0”
D
• t = 264 µs
• T0 = 1.05 ms
• T1 = 2.10 ms
• Pulse carrier frequency = 37.917 kHz
• Duty ratio = 1:1
Transmission control code
15 bit
C2
C3
C4
System Address
D to D Common Data Bit
C5
C6
C7
C8
Example of Reverse D to D
C9
C10
C11
Function Key Data Bit
C12
C13
Data
Expansion
C14
C15
Data
Mask Determination
D
D
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
1
0
1
1
0
1
0
0
0
0
0
0
0
1
0
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
1
0
1
1
0
0
1
1
1
1
1
1
1
0
1
Appendix
C1
Reverse in D
-59
Computer Compatibility Chart
Computer
• Multiple signal support
Horizontal Frequency: 15–81 kHz, Vertical Frequency: 43–100 Hz, Pixel Clock: 12–150 MHz
• Compatible with sync on green and composite sync signals (TTL level)
• AICS (Advanced Intelligent Compression and Expansion System) resizing technology
The following is a list of modes that conform to VESA. However, this projector supports other signals that
are not VESA standards.
PC/
MAC
Resolution
640 × 350
720 × 350
640 × 400
720 × 400
VGA
640 × 480
800 × 600
SVGA
XGA
1024 × 768
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
27.0
31.5
37.9
27.0
31.5
27.0
31.5
37.9
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
47.9
53.0
31.4
35.1
37.9
44.5
48.1
46.9
53.7
56.8
64.0
35.5
40.3
48.4
56.5
60.0
68.7
73.5
77.2
80.6
60
70
85
60
70
60
70
85
60
70
85
50
60
70
72
75
85
90
100
50
56
60
70
72
75
85
90
100
43
50
60
70
75
85
90
96
100
VESA
Standard
DVI
Support
PC/
MAC
Resolution
1152 × 864
✔
SXGA
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
1152 × 882
1280 × 1024
SXGA+ 1400 × 1050
—
1280 × 720
1280 × 768
WXGA
1360 × 768
1600 × 900
WSXGA
1920 × 1080*
MAC 13" 640 × 480
MAC 16"
832 × 624
MAC 19" 1024 × 768
MAC 21"
1152X870
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
55.0
66.2
64.1
67.5
76.6
54.8
65.9
67.4
64.0
64.0
45.0
47.8
47.6
55.9
66.8
34.9
46.8
49.6
48.4
60.0
68.5
60
70
72
75
80
60
72
74
60
60
60
60
60
60
60
67
75
75
60
75
75
VESA
Standard
✔
✔
DVI
Support
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
* When a 1920 x 1080 signal is input, the image is compressed before it is
displayed on the screen.
Note
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD)
mode. Should this occur, turn off the LCD display on the notebook computer and output the display data
in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s
operation manual.
• When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.
• When projecting moving image of interlace signals using RGB input, the intended image may not be projected depending on the signal types. In such cases, use the component, S-video or video input.
DTV
Signal
480I
480P
576I
576P
720P
720P
1080I
1080I
1080P*
1080P*
Horizontal Frequency (kHz)
15.8
31.5
15.6
31.3
45.0
37.5
33.8
28.1
62.5
67.4
* True display when “RESIZE” is set to “DOT BY DOT”
-60
Vertical Frequency (Hz)
60
60
50
50
60
50
60
50
50
60
HDMI Support
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Troubleshooting
Problem
No picture and no sound
or projector does not start
Check
• Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The selected input mode is wrong.
• Cables incorrectly connected to rear panel of the projector.
• Remote control batteries have run out.
• External output has not been set when connecting notebook
computer.
• The cover of the lamp unit is not installed correctly.
• The selected “Signal Type” is wrong.
• The video signal format of the video equipment is not set
correctly.
• “Bright” is set to minimum position.
• Picture adjustments are incorrectly set.
(S-VIDEO or VIDEO input)
• Video input system is incorrectly set.
(COMPONENT, DVI or HDMI input)
• Input signal type is incorrectly set.
Page
25
–
27
18-25
11
–
49,50
44
43
29,36
36
43
44
Color is faded or poor.
Picture is blurred;
noise appears.
46
• “LED” is set to “Off”.
43
• Change the input signal type setting.
44
27
16
41
41
–
38
–
–
Appendix
An unusual sound is
occasionally heard
from the cabinet.
Maintenance
indicator on the
projector illuminates.
Power indicator and
lamp indicator do not come
on while projecting.
Picture is green when receiving component signals
and the signal type setting
is set to COMPONENT/
RGB 1 or 2.
Picture is pink when receiving RGB signals and
the signal type setting is
set to COMPONENT/RGB
1 or 2.
• Adjust the focus.
• The projection distance exceeds the focus range.
(Computer input)
• Perform “Fine Sync” Adjustments (“Clock” Adjustment)
• Perform “Fine Sync” Adjustments (“Phase” Adjustment)
• Noise will appear depending on the computer.
• The “DNR” (Digital Noise Reduction) setting is not correct.
• There is fog on the lens. If the projector is carried from a cold
room into a warm room, or if it is suddenly heated, condensation
may form on the surface of the lens and the image will become
blurred. Please set up the projector at least one hour before it is
to be used. If condensation should form, remove the power cord
from the wall outlet and wait for it to clear.
• If the picture is normal, the sound is due to cabinet shrinkage
caused by a room temperature changes. This will not affect
operation or performance.
• See “Maintenance Indicators/Maintenance”.
-61
Troubleshooting (Continued)
Problem
Check
Page
The black levels of the
image show banding
or appear faded when
HDMI1 or 2 is selected.
• Make adjustments that result in the best picture quality in the
“Dynamic Range” setting.
44
Picture is too bright and
whitish.
• Picture adjustments are incorrectly set.
36
The cooling fan
becomes noisy.
The lamp does not light
up even after the
projector turns on.
• When temperature inside the projector increases, the cooling
fan runs faster.
• The lamp indicator is illuminating in red.
Replace the lamp.
–
46,49
The lamp suddenly turns
off during projection.
The image sometimes
flickers.
• Cables incorrectly connected to the projector or the connected
equipment works improperly.
• If this happens frequently, replace the lamp.
18-24
49
• The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the
lamp.
49
A response code cannot
be received when the
projector was attempted
to be controlled using
RS-232C commands
from a computer during
standby.
• In the case of transmitting RS-232C commands from a computer
during standby, it takes a maximum of 30 seconds for the computer
to receive the response code. Set the response code waiting time of
the computer to 30 seconds or more.
52
The remote control
cannot be used.
• Operate the remote control while pointing it at the projector’s
remote control sensor.
• The remote control may be too far away from the projector.
• If direct sunlight or a strong fluorescent light is shining on the
projector’s remote control sensor, place the projector where it
will not be affected by strong light.
11
• The batteries may be depleted or inserted incorrectly. Make
sure the batteries are inserted correctly or insert new ones.
11
The lamp needs much
time to turn on.
Picture is dark.
11
11
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect
operation or interference. If this should happen, unplug the Unit and plug it in again after more than
5 minutes.
-62
Specifications
Product type Projector
Model XV-Z21000
Video system NTSC 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM
DTV480I/DTV480P/DTV720P/DTV1080I/DTV1080P
Display method DLP® chip
DLP® panel Panel size: 0.95"
No. of dots: 2,073,600 dots (1,920 [H] × 1,080 [V])
Lens 1–1.35 × zoom lens, F2.5–8, f = 38.9–52.4 mm
Projection lamp 220 W SHP lamp
Video input signal RCA Connector: VIDEO (VIDEO), composite video, 1.0 Vp-p, sync negative, 75 Ω terminated
S-video input signal 4-pin Mini DIN connector (S-VIDEO)
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
Component input signal RCA Connector (COMPONENT/RGB1, 2)
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB: 0.7 Vp-p, 75 Ω terminated
PR: 0.7 Vp-p, 75 Ω terminated
Analog RGB/Digital input signal 29-pin DVI-I terminal (DVI)
<Digital>
Input impedance 50 Ω
Input level 250-1000 mV
<Analog>
Input Impedance 75 Ω
Input level 0.7 Vp-p
<Synchronization signal>
• Separate sync / Composite sync
Input level TTL level
Input impedance 1 KΩ
• Green on sync
Input level (Synchronizing input) 0.286 Vp-p
Input Impedance 75 Ω
HDMI input signal HDMI terminal (Video signal only)
TRIGGER terminal Power jack: DC 12 V output
Computer control signal 9-pin D-sub connector (RS-232C Terminal)
Horizontal resolution 520 TV lines (NTSC 3.58 input), 750 TV lines (DTV 720P input)
Pixel clock 12–150 MHz
Vertical frequency 43–100 Hz
Horizontal frequency 15–81 kHz
Rated voltage AC 100–240 V
Input current 3.3 A (When using AC 100 V)
Rated frequency 50/60 Hz
Power consumption 320 W (Lamp Setting “Bright”)/
265 W (Lamp Setting “Eco + Quiet”) with AC 100 V
310 W (Lamp Setting “Bright”)/
260 W (Lamp Setting “Eco + Quiet”) with AC 240 V
Power consumption (standby) 0.1 W (AC 100 V, RS-232C OFF) - 0.18 W (AC 240 V, RS-232C OFF)
Heat dissipation 1,200 BTU/hour
Operating temperature 41°F to 95°F (+5°C to +35°C)
Storage temperature –4°F to 140°F (–20°C to +60°C)
Cabinet Plastic
I/R carrier frequency 38 kHz
Dimensions (approx.) 18 11/16" × 6 51/64" × 16 5/32" (475 (W) × 172.5 (H) × 410.2 (D) mm) (main body only)
Weight (approx.) 20.7 lbs. (9.4 kg)
Replacement parts Remote control, Power cord for Europe, except U.K., Power cord for U.K. and Singapore,
Power cord for Australia, New Zealand and Oceania, 21 pin RCA conversion adaptor, Video
cable, DVI to D-sub cable, Lens cap, Terminal cover, Projector operation manual
Appendix
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
-63
Dimensions
16 5/32 (410.2)
Units: inch (mm)
8 25/32 (223.1)
37
8 3/8 (212.5)
8 3/8 (212.5)
18 45/64 (475)
19
/32 (15)
6 51/64 (172.5)
4 7/32 (107) 3 11/64 (80.5)
/64 (14.4)
9 5/32 (232.5)
M4
M4
43
/64 (16.9)
3 23/64 (85.1) 3 5/64 (77.9)
-64
1 25/64 (35)
3 1/8 (79.1) 6 17/64 (158.9)
M4
Index
Accessories ............................................................ 4
AC socket ............................................................. 25
Adjustment buttons ............................................. 34
Adjustment feet .................................................... 28
Advanced ............................................................. 37
All Reset ............................................................... 45
Automatic Contrast .............................................. 39
Auto Power Off ..................................................... 45
Auto Sync ............................................................. 41
AUTO SYNC button ............................................. 41
Background .......................................................... 44
Batteries ............................................................... 11
Black Level ........................................................... 43
Bright .................................................................... 36
BRIGHT button ..................................................... 29
BrilliantColorTM ...................................................... 38
Ceiling-mount setup ............................................. 15
CINEMA ZOOM .................................................... 31
Clock .................................................................... 41
CLR Temp (Color Temperature) ............................ 36
C.M.S. .................................................................. 37
Color ..................................................................... 36
Color Space.......................................................... 44
COMPONENT/RGB 1 terminal ....................... 20, 21
COMPONENT/RGB 2 terminal ....................... 20, 21
Contrast ................................................................ 36
CONTRAST button ............................................... 29
DNR ...................................................................... 38
DOT BY DOT ........................................................ 31
DVI terminal ...............................................18-20, 23
Dynamic Range .................................................... 44
Economy Mode .................................................... 44
ENTER button....................................................... 34
Fan Mode ............................................................. 45
Film Mode............................................................. 38
Fine Sync .............................................................. 41
Focus ring............................................................. 27
FREEZE button ..................................................... 29
Gamma ................................................................. 40
Gamma Position ............................................. 37, 40
HDMI1 terminal .................................................... 18
HDMI2 terminal .................................................... 18
H-Pos ................................................................... 41
Hue ....................................................................... 37
Kensington Security Standard connector .............. 9
Lamp indicator ..................................................... 46
Lamp Setting ........................................................ 37
Lamp Timer (Life) .................................................. 43
Language (on-screen display language) .............. 45
MENU button........................................................ 34
MNR ..................................................................... 38
ON button ............................................................. 25
Options ................................................................. 42
Optional accessories .............................................. 4
On-screen Display ................................................ 43
Overscan .............................................................. 42
Phase.................................................................... 41
Picture .................................................................. 36
Picture Mode ........................................................ 36
PICTURE MODE button ....................................... 29
Power cord ........................................................... 25
Power indicator ............................................... 25,46
PRJ mode ........................................................ 15,45
Progressive ........................................................... 38
Remote control ..................................................... 10
Remote control sensor ......................................... 11
Replacing the lamp .............................................. 48
RESIZE button ...................................................... 30
RETURN button .................................................... 34
RGB/COMP. button .............................................. 44
RS-232C ............................................................... 45
RS-232C Port ....................................................... 44
RS-232C terminal ................................................. 24
Saturation ............................................................. 37
Sharp .................................................................... 36
SIDE BAR ............................................................. 30
Signal Info............................................................. 41
Signal Type ........................................................... 44
SMART STRETCH ................................................ 30
SMART ZOOM ..................................................... 31
Special Modes...................................................... 41
STANDBY button .................................................. 26
STRETCH ............................................................. 30
Subtitle ................................................................. 42
S-VIDEO terminal ................................................. 22
Temperature warning indicator ............................. 46
Tint........................................................................ 36
TRIGGER terminal .................................................. 9
Unveil Control ....................................................... 39
Value ..................................................................... 37
Video System ....................................................... 43
VIDEO terminal ..................................................... 22
V-Pos .................................................................... 41
White Level ........................................................... 43
WIRED R/C JACK................................................. 10
WIRED REMOTE control input terminal ............... 10
ZOOM 14:9 ........................................................... 31
Zoom knob ........................................................... 27
-65
Appendix
Image Shift ........................................................... 42
INPUT button........................................................ 27
Input Mode Select buttons ................................... 27
IRIS ....................................................................... 37
IRIS button ........................................................... 29
LED ....................................................................... 43
Lens cap ................................................................. 8
Lens shift dial ....................................................... 28
LIGHT button ........................................................ 10
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
BRUKSANVISNING
MANUAL DE MANEJO
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
DEUTSCH
XV-Z21000
PROJECTOR
PROJEKTOR
PROJECTEUR
PROJEKTOR
PROYECTOR
PROIETTORE
PROJECTOR
ENGLISH
XV-Z21000
FRANÇAIS
SVENSKA
ESPAÑOL
ITALIANO
NEDERLANDS
Printed in China
In China gedruckt
Imprimé en Chine
Triykt i Kina
Impreso en China
Stampato in Cina
Gedrukt in China
TINS-C542WJZZ
06P07-CH_NM