CXOQ/CXOQHG OSCILLATOR 400 kHz to 100 MHz One of the World’s Smallest and Highest Precision Crystal Oscillators DESCRIPTION Technological advancements permit 2.5 mm x 2.0 mm CXOQ quartz oscillator to have design-in capabilities of withstanding high shock applications. Additionally, the ultraminiature CXOQ takes advantage of Statek’s well known reliability and impeccable quality. FEATURES DIMENSIONS High shock survival High frequency stability A Low acceleration sensitivity (HG version) CMOS and TTL compatible 4 Low power consumption C 3 B 1 Optional output enable/disable with Tri-State E 4 3 TOP Full military testing per MIL PRF 55310 available D BOTTOM 2 2 1 Low EMI emission Hermetically sealed ceramic package Designed, manufactured and tested in the USA TYPICAL MAXIMUM DIM inches mm inches mm A 0.098 2.50 0.102 2.60 B 0.079 2.00 0.083 2.10 Medical 0.035 C (SM1) C (SM3/SM5) 0.040 0.89 1.02 0.039 0.048 1.00 1.22 D 0.026 0.67 0.027 0.69 Industrial E 0.022 0.57 0.023 0.59 APPLICATIONS Military SUGGESTED LAND PATTERN PIN CONNECTIONS 1. Output Enable/Disable (E) or no connection (N) 0.114 (2.9) 2. Ground (Connected to Lid) 3. Output 4. VDD 0.094 (2.4) 0.025 (0.64) 0.038 (0.975) 0.037 (0.95) inches (mm) TEM C ERT I F I C AT IO S 10190 Rev A YS N IS O STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com 90 01 ABSOLUTE MAXIMUM RATINGS SPECIFICATIONS Supply Voltage VDD -0.5 V to 5.0 V Storage Temperature -55OC to 125OC Maximum Process Temperature 260OC for 20 seconds Specifications are typical at 25 C unless otherwise noted. Specifications are subject to change without notice. Tighter specifications are available. Please contact factory. O Frequency Supply Voltage1 400 kHz to 100 MHz 1.8V to 3.3 V ± 10% Calibration Tolerance ± 100 ppm to ± 30 ppm Frequency Stability Over Temperature3 ± 50 ppm for Commercial ± 100 ppm for Industrial ± 100 ppm for Military 1.8 V 24 MHz 1.5 mA 32 MHz 2.0 mA 50 MHz 3.0 mA 2 Supply Current (Typical) ENABLE/DISABLE OPTIONS (E/N) 3.3 V 3.0 mA 5.0 mA 6.0 mA Statek offers two enable/disable options: E and N. The E-version has a Tri-State output and stops oscillating internally when the output is put into the high Z state. The N-version does not have PIN 1 connected internally and so has no enable/disable capability. The following table describes the Enable/Disable option E. ENABLE/DISABLE OPTION E FUNCTION TABLE Output Load (CMOS) 15 pF Start-up Time 5 ms MAX Rise/Fall Time 10 ns MAX Output Frequency Output High Z State Duty Cycle4 45% MIN/55% MAX Oscillator Oscillates Stops 5 ppm Current Normal Very Low Aging, first year Enable (Pin 1 High*) Disable (Pin 1 Low) Shock, survival 5,000 g, 0.3 ms, HG: 20,000 g Vibration, survival6 20 g, 10-2,000 Hz swept sine Operating Temp. Ranges -10OC to 70OC -40OC to 85OC -55OC to 125OC 5 1/ 2 sine * When PIN 1 is allowed to float, it is held high by an internal pull-up resistor. (Commerical) (Industrial) (Military) PACKAGING OPTIONS CXOQ - Tray Pack - 12 mm tape, 7” or 13” reels Per EIA 481 (see Tape and Reel data sheet #10109) 1. Contact factory for available other voltages. 2. Tighter tolerances available. 3. Does not include calibration tolerances. Tighter tolerances available 4. Tighter duty cycles are available. 5. Higher shock available, contact factory for requirements above 20,000 g. 6. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also available. Note: All parameters are measured at ambient temperature with a 10 M!, 15 pF load. HOW TO ORDER CXOQ/CXOQHG SURFACE MOUNT CRYSTAL OSCILLATORS CXOQ HG 4 S N HG = High Shock otherwise leave blank Supply Voltage 1 = 1.8 V 2 = 2.5 V 3 = 3.0 V 4 = 3.3 V “S” if Special or custom design; otherwise blank Enable/Disable Option E or N SM3 Terminations Blank = SM1 = Gold Plated (Lead Free) SM3 = Solder Dipped SM5 = Solder Dipped (Lead Free) 32.0M Frequency K = kHz M = MHz , 100 Calibration Tolerance @ 250C (in ppm) / 100 / Frequency Stability over Temp. Range (in ppm) I / Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified OR / / 200 Total Frequency Tolerance (in ppm) / I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified TEM C ERT I F I C AT IO S 10190 Rev A YS N IS O STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com 90 01