CXOM OSCILLATOR 300 kHz to 120 MHz Low Profile Miniature Surface Mount Crystal Oscillator ™ DESCRIPTION Statek’s surface-mount CXOM oscillators consist of a Statek miniature quartz crystal and a CMOS/TTL compatible hybrid circuit in a low-profile ceramic package with an extremely small footprint. GM M 4.19 FEATURES Designed for surface mount applications using infrared, vapor phase, or epoxy mount techniques actual size side view CMOS and TTL compatible Low power consumption Optional Output Enable/Disable with Tri-State Low EMI emission DIMENSIONS High shock resistance Full military testing available D Hermetically sealed ceramic package APPLICATIONS 2 A TOP 3 BOTTOM Military & Aerospace 1 4 Smart Munitions D Cockpit Systems B Navigation E C Industrial, Computer & Communications Industrial Controls TYPICAL Instrumentation Microprocessor Clocks Medical Infusion Pumps SUGGESTED LAND PATTERN MAXIMUM DIM inches mm inches mm A 0.256 6.50 0.263 6.68 B 0.197 5.00 0.204 5.18 0.051 C (SM1) C (SM3/SM5) 0.055 1.30 1.40 0.055 0.063 1.40 1.60 D 0.055 1.40 0.065 1.65 E 0.060 1.52 0.070 1.78 0.070 (1.78) 0.067 (1.70) PIN CONNECTIONS 0.065 (1.65) 1. Enable/Disable (E or T) or not connected (N) 2. Ground 0.201 (5.11) 0.136 (3.45) 3. Output 4. VDD 0.137 (3.48) GRID PLACEMENT COURTYARD 10116 Rev E IS O STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com YS 90 01 TEM C ERT I F I C AT N IO S inches (mm) ABSOLUTE MAXIMUM RATINGS SPECIFICATIONS O Specifications are typical at 25 C unless otherwise noted. Specifications are subject to change without notice. Tighter specifications available. Please contact factory. Supply Voltage1 5.0 V Calibration Tolerance2 + _ Frequency Stability Over Temperature3 + _ Supply Current (Typical) ENABLE/DISABLE OPTIONS (E/T/N) 100 ppm 15 pF Start-up Time Rise/Fall Time 5 ms MAX 6 ns MAX Duty Cycle 40% MIN, 60% MAX COMPARISON OF ENABLE/DISABLE OPTIONS E AND T 10 ppm MAX Shock, survival 3,000 g, 0.3 ms, 1/2 sine Vibration, survival6 20 g, 10-2,000 Hz swept sine 5 Statek offers three enable/disable options: E, T, and N. Both the E-version and T-version have Tri-State outputs and differ in whether the oscillator continues to run internally when the output is put into the high Z state: it stops in the E-version and continues to run in the T-version. So, the E-version offers very low current consumption when the oscillator is disabled and the T-version offers very fast output recovery when the oscillator is re-enabled. The N-version does not have PIN 1 connected internally and so has no enable/disable capability. The following table summarizes the three options. 50 ppm for Commercial 100 ppm for Industrial + _ 100 ppm for Military 10 MHz 4 mA 24 MHz 8 mA 30 MHz 10 mA 40 MHz 12 mA 50 MHz 14 mA + _ Output Load (CMOS)4 Aging, first year Supply Voltage VDD -0.5 V to 7.0 V Storage Temperature -55OC to +125OC Maximum Process Temperature 260OC for 20 seconds E T When enabled (PIN 1 is high*) Operating Temp Ranges -10OC to +70OC (Commercial) -40OC to +85OC (Industrial) -55OC to +125OC (Military) 1. Other voltages available. For 3.3 V, see CXO3M data sheet (10126). For others, contact factory. 2. Other tolerances available. 3. Does not include calibration tolerance. Other tolerances available. 4. Higher CMOS loads and TTL loads available. Contact factory. 5. Higher shock version available. Contact factory about CXOMHG. 6. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also available. Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF load. Output Freq. output Freq. output Oscillator Oscillates Oscillates Current consumption Normal Normal Output High Z state High Z state Oscillator Stops Oscillates Current consumption Very low Lower than normal When disabled (PIN 1 is low) When re-enabled (PIN 1 changes from low to high) Output recovery Delayed Immediate PACKAGING OPTIONS * When PIN 1 is allowed to float, it is held high by an internal pull-up resistor. CXOM - Tray Pack - 16mm tape, 7˝ or 13˝ reels Per EIA 418 (see Tape and Reel data sheet 10109) HOW TO ORDER CXOM SURFACE MOUNT CRYSTAL OSCILLATORS CXOM S “S” if special or custom design; otherwise blank. T Enable/Disable Option E, T, or N SM3 Terminations Blank = SM1 = Gold Plated SM3 = Solder Dipped SM5 = Solder Dipped (Lead Free) 32.0M , Frequency K = kHz M = MHz 100 / 100 / / Frequency Stability over Temp.Range (in ppm) Calibration Tolerance @ 250C (in ppm) I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified OR / / 200 I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified 10116 Rev E IS O STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com YS 90 01 TEM C ERT I F I C AT N IO S Total Frequency Tolerance (in ppm) /