SEALED UNMATED POWER JACKS NPB | 608 5555 N ELSTON AVE | CHICAGO, IL 60630 | P: 773.792.2700 | F: 773.792.2129 | WWW.SWITCHCRAFT.COM SEALED UNMATED POWER JACKS NPB | 608 FEATURES & BENEFITS APPLICATIONS • Up to 13A current rating (carry) • Any sealed data transmission • Military or industrial GPS location devices • Up to 24V AC/DC • Available in sealed only but can be used with S10 style plugs both sealed and non-sealed • Recommend plug locking versions to keep plugs connected to jack. • Instrumentation • Medical equipment • Marine Applications • Transportation • General industrial electronic applications • Power supplies PLEASE VISIT WWW.SWITCHCRAFT.COM FOR THE MOST UP-TO-DATE PRODUCT SPECIFICATIONS. MADE IN USA SEALED UNMATED POWER JACKS NPB | 608 SEALED UNMATED POWER JACK, STRAIGHT - ORDERING CODE: ST10U SEALED UNMATED POWER JACK, STRAIGHT - ORDERING CODE: ST10U SEALED UNMATED POWER JACK, RIGHT ANGLE - ORDERING CODE: RAPC10U SEALED UNMATED POWER JACK, RIGHT ANGLE - ORDERING CODE: RAPC10U UNITS ARE LISTED IN INCHES. ALL DIMENSIONS ARE REFERENCE ONLY. PLEASE VISIT WWW.SWITCHCRAFT.COM FOR THE MOST UP-TO-DATE PRODUCT SPECIFICATIONS. MADE IN USA SEALED UNMATED POWER JACKS NPB | 608 SPECIFICATIONS MECHANICAL SPECIFICATIONS Life: Vibration: Operating Forces: Panel Mount Torque: 5000 mechanical cycles minimum using S10 style plugs Mil-Std 202G Method 201A (jack or when mated with locking plug) 3 lb maximum insertion 0.2 lb minimum withdrawal when using S10 typle plug 8-10 in/lb ELECTRICAL SPECIFICATIONS Voltage Rating: Current Rating: Insulation Resistance: Contact Resistance (Initial): 24V AC/DC Refer to current rating table 1000 MΩ minimum initial 10 mΩ maximum ENVIRONMENTAL SPECIFICATIONS Operaing Temperature Rating: Moisture Resistance: Insulation Resistance: Thermal Shock: Salt Atmosphere (Corrosion): Weathertight Ratings: -40 °C to +105 °C(-40ºF to +221°F) Mil-Std 202G Method 106G (jack or when mated with sealed locking plug) Mil-Std 202G Method 302 (Condition B Only) Mil-Std 202G Method 107G (jack or when mated with sealed locking plug) Mil-Std 202G Method 101E Condition B IP66, IP67, IP68, NEMA 250 (6P) (jack or when mated with sealed locking plug) Copper Alloy, Nickel Plated Steel, Nickel Plated Thermoplastic, Black Elastomer, Black Elastomer, Amber Copper Alloy, Gold over Silver Plated Copper Alloy, Matte Tin Plated Copper Alloy, Gold over Silver Plated MATERIAL SPECIFICATIONS Housing, Hex Nut: Washer: Insulator: O-Ring: Internal O-Rings: Center Pin: Center Pin & Shunt Terminals: Sleeve Spring Contact: CURRENT RATING TABLE WHEN MATED TO S10 STYLE PLUGS Wire (awg) 90°C max 16 18 20 13 12 11 Current Rating (A) at Operating Temperature (°C) 95°C max 100°C max 12 11 10 11 10 9 105°C max 10 9 8 Note: DC Power Plugs & Jacks are for current carrying only. Do not connect or disconnect under load. The circuitry on-off switch should be off before connecting and disconnecting the Power Plug to the Jack. If water gets in the jack, it may cause low impedance between contacts but the water will not get inside your product if mounted properly. Blow the water out of the jack and let dry, the impedance will return to normal. PLEASE VISIT WWW.SWITCHCRAFT.COM FOR THE MOST UP-TO-DATE PRODUCT SPECIFICATIONS. MADE IN USA