DATA SHEET SKY66100-11: 169 to 170 MHz Transmit/Receive Front-End Module Applications Description Automated meter reading The SKY66100-11 is a high-performance, transmit/receive (Tx/Rx) front-end module (FEM). The device includes a power amplifier (PA) capable of more than +27 dBm of transmit output power at more than 45 percent PAE for the module (55 percent for the standalone PA). For current-sensitive applications, the PA can be bypassed to save battery current. Advanced metering infrastructure ISM systems Features All functionality can be controlled by a three-wire interface. The FEM can be placed in a deep “sleep” mode, drawing less than 1 μA of current. Transmit output power: >+27 dBm High efficiency PA The receive chain consists of a low-loss single-pole, triple-throw (SP3T) switch, which provides an insertion loss of approximately 0.4 dB. Three separate VCC pins enable maximum RF isolation. Receive loss: <0.4 dB Transmit bypass mode with 0.9 dB insertion loss Sleep mode current: < 1 μA The SKY66100-11 is packaged in a 16-pin, 4 x 4 mm Multi-Chip Module (MCM), which allows for a highly manufacturable low-cost solution. Integrated control logic Small footprint MCM (16-pin, 4 x 4 mm) package (MSL3, 260 C per JEDEC J-STD-020) Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. Output Matching Network PA_OUT TX CSD CTX BYP A functional block diagram of the SKY66100-11 is shown in Figure 1. The 16-pin MCM package and pinout are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. TX_IN Logic Control PA SPST Regulator Filter ANT RX SP3T Y0537 Figure 1. SKY66100-11 FEM Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201829E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 1, 2015 1 VCC1 VCC0 VCC2 DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM 16 15 14 13 PA_OUT TX 2 12 GND CTX 3 11 GND RX 4 10 TX_IN 9 GND CSD_L 1 6 7 8 GND CBYP_L ANT N/C 5 S2784 Figure 2. SKY66100-11 Pinout – 16-Pin MCM (Top View) Table 1. SKY66100-11 Signal Descriptions Pin Name Description Pin Name Description 1 CSD_L Control, shutdown/sleep, active low 9 GND Ground 2 TX Transmit RF input 10 TX_IN Transmit input. Externally filtered signal. 3 CTX Control, transmit modes 11 GND Ground 4 RX Receive RF output 12 GND Ground 5 N/C No connection 13 PA_OUT PA output 6 GND Ground 14 VCC2 Supply for second stage of PA 7 CBYP_L Control, transmit bypass mode 15 VCC0 Supply for logic, regulator, bias 8 ANT Antenna I/O 16 VCC1 Supply for first stage of PA Technical Description Electrical and Mechanical Specifications The SKY66100-11 consists of a complete Tx/Rx chain with Tx/Rx switches contained in the module. An SP3T switch selects between receive, transmit, and transmit bypass paths. The module has a shutdown mode to minimize power consumption. The absolute maximum ratings of the SKY66100-11 are provided in Table 2. The recommended operating conditions are specified in Table 3, and electrical specifications are provided in Tables 4 through 7. Three digital input control pins (CSD_L, CTX, and CBYP_L) are used to select between shutdown, Tx/Rx, or transmit bypass mode, respectively. The state of the SKY66100-11 is determined by the logic provided in Table 8. The bypass mode can also be configured to power-down the PA and remove it from the RF path using an internal single-pole, single-throw (SPST) switch. Typical performance characteristics are shown in Figures 3 through 11. The transmit path contains a PA optimized for saturated performance. The PA can be passed through an external impedance matching network and harmonic filter before being fed through the SP3T switch. External inductors for each of the two PA stages provide maximum application flexibility. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 June 1, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201829E DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM Table 2. SKY66100-11 Absolute Maximum Ratings (Note 1) Parameter Symbol Minimum Maximum Units +3.8 V Supply voltage (Pins: VCC0, VCC1, VCC2) VCC –0.3 Digital input voltage (Pins: CSD_L, CTX, CBYP_L) VCTL –0.5 Receive mode (Pin: ANT) PIN_ANT VCC V +15 dBm Transmit mode (Pin: TX) PIN_TX –4 dBm Transmit RF input power, transmit bypass mode (Pin:TX) PIN_TXB +20 dBm Transmit output power POUT +28 dBm Voltage Standing Wave Ratio VSWR 10:1 – Thermal resistance ΘJC 14.7 C/W Operating temperature TC –40 +85 C Storage temperature TSTG –55 +150 C Junction temperature TJ +150 C Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. SKY66100-11 Recommended Operating Conditions Parameter Symbol Minimum Typical Operating frequency range f 169 Supply voltage (Pins: VCC0, VCC1, VCC2) VCC 2.0 Receive RF input power (Pin: RX) PIN_RX Transmit RF input power, transmit mode (Pin:TX) PIN_TX –6 Transmit RF input power, transmit bypass mode (Pin: TX) PIN_TX +15 Transmit mode duty cycle 3.3 Maximum Units 170 MHz 3.6 V –15 dBm dBm +20 dBm 50 % Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201829E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 1, 2015 3 DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM Table 4. SKY66100-11 DC Electrical Specifications (Note 1) (VCC = +3.3 V, TC = +25 C, with Output Matching Network as Noted, Unless Otherwise Noted) Parameter Symbol Receive quiescent current (Pins: VCC0, VCC1, VCC2) IQ_RX Transmit quiescent current (Pins : VCC0, VCC1, VCC2) IQ_TX Transmit bypass quiescent current (Pins: VCC0, VCC1, VCC2) IQ_TXBYP Transmit operating current (Pins: VCC0, VCC1, VCC2) IOP_TX Shutdown current (Pins: VCC0, VCC1, VCC2) (Note 5, Note 6, and Note 7) Test Condition Min Typical Max Units Rx mode (Note 2) 680 μA Tx mode 15 mA Tx bypass mode (Note 2) 680 μA VCC = 3.3 V, POUT = +24 dBm (Note 3 and Note 5) 210 mA VCC = 3.6 V, 325 mA TX mode: POUT = +27 dBm (Note 4) ISD Shutdown/sleep mode 0.02 1.0 μA Note 1: Performance is guaranteed only under the conditions listed in this table. Note 2: Does not include control pin currents. See Table 7 for more information. Note 3: Requires EK1 output match network designed for +24 dBm. See Figure 3. Contact Skyworks Application Support for more information. Note 4: Requires EK2 output match network designed for +27 dBm. See Figure 4. Contact Skyworks Application Support for more information. Note 5. Not production tested. Note 6: Shutdown mode functionally verified in production to be less than 1 mA. Note 7: All controls must be <0.1 V to achieve the specified sleep current. Table 5. SKY66100-11 Receive Mode Electrical Specifications (Note 1) (VCC = +3.3 V, TC = +25 C, f = 169 to 170 MHz, Characteristic Source and Load Impedance = 50 Ω, CW Input, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Receive Mode: ANT to RX Output Path (Note 2) Insertion loss (Note 3) IL 1 dB input compression point (Note 4) IP1dB +15 dBm 3 order input intercept point (Note 4) IIP3 +29 dBm Input return loss (Note 4) |S11| 8 dB Power-on time, RX (Note 4 and Note 5) TON_RX rd 0.4 Final mode = RX (see Table 8) 1 Note 1: Performance is guaranteed only under the conditions listed in this table. Note 2: Mode configured according to logic shown in Table 8. Note 3: Insertion loss increases to 0.9 dB when using an external antenna filter. See Figure 3. Note 4: Not production tested. Note 5: Elapsed time is from sleep mode to the final mode indicated in Table 8. A final mode is considered achieved when its corresponding POUT is at least 90% of its final value. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 June 1, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201829E dB μs DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM Table 6. SKY66100-11 Transmit Mode Electrical Specifications (Note 1) (Note 2) (VCC = +3.3 V, TC = +25 C, f = 169 to 170 MHz, Characteristic Source and Load Impedance = 50 Ω, with Output Matching Network as in Figure 3, CW Input, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Transmit Mode: TX to PA_OUT TX_IN to ANT Path (Note 3) Output power POUT VCC = 3.6 V (Note 4) VCC = 3.3 V (Note 5 and Note 6) +27 +24 dBm dBm PA power added efficiency (Note 7) PAE_PA At PA_OUT pin (Note 4) At PA_OUT pin (Note 5 and Note 6) 45 55.8 % % 2nd harmonic (Note 6 and Note 8) 2fo –36 dBm 3rd to 10th harmonics (Note 6 and Note 8) 3fo 4fo 5fo 6fo 7fo 8fo 9fo 10fo –54 –54 –54 –54 –54 –54 –54 –54 dBm dBm dBm dBm dBm dBm dBm dBm Input return loss (Note 6 and Note 9) |S11| PIN = –30 dBm 8 dB Output return loss (Note 3 and Note 6) |S22| PIN = –30 dBm 6 dB Non-harmonic spurious power (Note 6, Note 8, and Note 10) VSWR = 5:1, all phases Power-on time (Note 6 and Note 11) TON_TX Receive isolation (Note 13) |SRXTX| –40 Final mode = transmit (see Table 8) dBm 2.8 μs 12 dB 0.9 dB Transmit Bypass Mode: TX to ANT Path Insertion loss (Note 12) IL 1 dB input compression point (Note 6) IP1dB nd VCC = 3.0 to 3.6 V 21 dBm 2 harmonic (Note 6 and Note 8) 2fo PIN_TX = +20 dBm –36 dBm 3rd to 5th harmonics (Note 6 and Note 8) 3fo-5fo PIN_TX = +20 dBm –54 dBm Input return loss (Note 6 and Note 9) |S11| 6 dB Output return loss (Note 3 and Note 6) |S22| 8 dB Transition time (Note 6 and Note 11) tON Receive isolation |SRXTX| Final mode = transmit bypass (see Table 8) 1 μs PIN_TX = +20 dBm 25 dB Note 1: Performance is guaranteed only under the conditions listed in this table. Note 2: Mode configured according to logic shown in Table 8. Note 3: External output matching network and filter located between PA_OUT and TX_IN (pins 13 and 10, respectively). Note 4: Requires EK2 output match network designed for +27 dBm. See Figure 4. Contact Skyworks Application Support for more information. Note 5: Requires EK1 output match network designed for +24 dBm. See Figure 3. Contact Skyworks Application Support for more information. Note 6: Not production tested. Note 7: Calculated from Evaluation Board test results with loss of output matching network. Note 8: Final performance dependent on external filter. The 2nd to 10th harmonics are fully characterized but are not production tested. Note 9: External input matching network. Note 10: Measurement performed with spectrum analyzer (RBW = 100 kHz for frequencies < 1 GHz and RBW = 1 MHz for frequencies between 1 GHz and 10 GHz). Note 11: Elapsed time is from sleep mode to the final mode indicated in Table 8. A final mode is considered achieved when its corresponding POUT is at least 90% of its final value. Note 12: The insertion loss increases to 2 dB in TX bypass mode with the external input match. The RX bypass is not affected. Note 13: Includes gain of PA. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201829E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 1, 2015 5 DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM Table 7. SKY66100-11 Electrical Specifications: Control Logic Characteristics (Note 1) (TC = +25 C, Unless Otherwise Noted) Parameter Symbol Control voltage (Note 2): High Low VIH VIL Input current (Note 3): High Low IIH IIL Test Condition Min Typical 1.6 0 Max Units VCC 0.7 V V TC = 25 °C μA μA 36 0 Note 1: Performance is guaranteed only under the conditions listed in this table. Control logic input signals are: CSD_L, CTX, and CBYP_L. Note 2: Not production tested. Note 3: Each control pin has a 100 kΩ pull-down resistor. Table 8. SKY66100-11 Mode Control Logic (Note 1) Mode Sleep RF Signal Path Pin Pin CSD_L (Pin 1) CTX (Pin 3) CBYP_L (Pin 7) (Note 2) 0 X X Transmit bypass TX ANT 1 1 0 Receive ANT RX 1 0 X Transmit TX to PA_OUT TX_IN to ANT 1 1 1 Note 1: “1” = 1.6 to Vcc, “0” = 0 to 0.7 V, “X” = don’t care. Note 2: All I/O are disconnected from internal components. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 June 1, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201829E DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM Typical Performance Characteristics 500 26 450 24 400 22 350 20 300 18 250 16 200 14 10 -22 38 150 Pout [dBm] ICC [mA] 12 40 -18 -16 -14 -12 -10 -8 34 169 MHz 169.5 MHz 170 MHz 32 100 50 -20 36 30 0 -6 Input Power (dBm) Y2004 550 28 Gain (dB) 30 ICC (mA) POUT (dBm) (VCC = 3.6 V, f = 169 MHz CW Signal, Unless Otherwise Noted) 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Output Power (dBm) Y2003 Figure 4. Gain vs. POUT Figure 3. POUT and ICC vs PIN 33 400 300 Gain (dB) ICC (mA) 32 200 31 Y2005 30 169 169.5 0 0 170 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Output Power (dBm) Frequency (MHz) Figure 6. ICC vs POUT Figure 5. Small Signal Gain vs Frequency 40 55 2V 2.7 V 3V 3.3 V 3.6 V 39 50 38 37 40 36 2V 2.7 V 3V 3.3 V 3.6 V 30 25 17 18 19 20 21 22 23 24 25 26 Output Power (dBm) Figure 7. PAE vs POUT and VCC 27 28 29 34 33 32 20 16 35 30 31 Y2008 35 Gain (dB) 45 Y2007 PAE (%) Y2006 169 MHz 169.5 MHz 170 MHz 100 30 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Output Power (dBm) Figure 8. Gain vs POUT and VCC Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201829E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 1, 2015 7 DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM -40 -60 -70 169 MHz 169.5 MHz 170 MHz -80 16 17 18 19 20 21 22 23 24 25 26 27 169 MHz 169.5 MHz 170 MHz -50 -60 -70 -80 Y2010 3rd Harmonic (dBm) -50 Y2009 2nd Harmonic (dBm) -40 -90 16 28 17 18 19 20 21 22 23 24 25 Output Power (dBm) Output Power (dBm) Figure 10. 3rd Harmonic vs POUT Figure 9. 2nd Harmonic vs POUT 0 -10 169 MHz 169.5 MHz 170 MHz -20 Level (dBm) -30 -40 -50 -60 -70 Y2011 -80 -90 -100 2nd 3rd 4th 5th 6th 7th 8th 9th 10th Harmonics Figure 11. Harmonics at POUT = +27 dBm Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 June 1, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201829E 26 27 28 DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM Evaluation Board Description Package and Handling Information The SKY66100-11 Evaluation Board is used to test the performance of the SKY66100-11 FEM. Evaluation Board schematic diagrams are provided in Figure 12 (EK-1 board, +24 dBm) and in Figure 13 (EK-2 board, +27 dBm). An assembly drawing for the Evaluation Board is shown in Figure 14. Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. Package Dimensions The typical part marking for the SKY66100-11 is shown in Figure 15. The PCB layout footprint for the SKY66100-11 is provided in Figure 16. Figure 17 shows the package dimensions for the 16-pin MCM, and Figure 18 provides the tape and reel dimensions. The SKY66100-11 is rated to Moisture Sensitivity Level 3 (MSL3) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, PCB Design and SMT Assembly/Rework Guidelines for MCM-L Packages, document number 101752. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201829E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 1, 2015 9 DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM C22 4.7 μF J8 VCC BYP FB1 C28 1 μF CTX C29 1 μF CSD 2 1 4 3 6 5 8 7 10 9 12 11 14 13 VCC C27 1 nF C30 4.7 nF C21 DNI L13 10 nH L9 10 nH 2 CTX C26 22 pF 1 4 CSD TX CTX RX L29 3.3 nH L14 27 nH GND GND TX_IN GND 12 C16 2.2 nF 11 C23 47 pF 10 9 N/C GND BYP ANT C25 DNI 3 15 14 13 VCC2 PA_OUT CSD L8 27 nH J6 SMA 16 VCC1 VCC0 Pad 17 C24 56 pF L21 6.8 nH 5 6 7 8 BYP C100 2.2 nF J7 SMA C101 22 pF L10 47 nH L30 4.7 nH C19 18 pF Notes: L11 0Ω L31 DNI Some component labels may be different from the corresponding component symbol shown here. Component values, however, are accurate as of the date of this data sheet. J5 SMA C20 DNI Y2001 Figure 12. SKY66100-11 EK-1 Evaluation Board Schematic (+24 dBm) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 June 1, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201829E DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM C22 4.7 μF J8 VCC BYP FB1 C28 1 μF CTX C29 1 μF CSD 2 1 4 3 6 5 8 7 10 9 12 11 14 13 VCC C27 1 nF C30 4.7 nF C21 DNI L13 12 nH L21 6.8 nH L9 12 nH 2 CTX C26 22 pF 1 4 CSD TX CTX RX L29 3.9 nH L14 27 nH GND GND TX_IN GND 12 C16 2.2 nF 11 C23 33 pF 10 9 N/C GND BYP ANT C25 DNI 3 15 14 13 VCC2 PA_OUT Pad CSD L8 27 nH J6 SMA 16 VCC1 VCC0 17 C24 56 pF 5 6 7 8 BYP C100 2.2 nF J7 SMA C101 22 pF L10 47 nH L30 4.7 nH C19 18 pF Notes: L11 0Ω L31 DNI Some component labels may be different from the corresponding component symbol shown here. Component values, however, are accurate as of the date of this data sheet. J5 SMA C20 DNI Y2002 Figure 13. SKY66100-11 EK-2 Evaluation Board Schematic (+27 dBm) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201829E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 1, 2015 11 Y1996 DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM Figure 14. SKY66100-11 Evaluation Board Assembly Drawing (Applies to both EK-1 and EK-2 Evaluation Boards) PCB Recommendations Recommendations for 4-layer PCB: Metal Layer 1 = RF traces + control lines. Metal Layer 2 = Solid ground plane. No traces routing. Use vias to ground under the FEM as recommended in Figure 5. Metal Layer 3 and 4 = Control lines + VCC traces (no VCC plane). Pour copper on each layer connected to the ground plane. Use VCC traces in a star distribution pattern. Recommendations for 2-layer PCB: Metal Layer 1 = RF traces + control lines + VCC. Metal Layer 2 = Solid ground plane between the transceiver and the FEM up to the antenna, no traces routing in that area. Use vias to ground under the FEM as recommended in Figure 5. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 June 1, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201829E DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM Pin 1 Indicator Skyworks Part Number 66100-11 STR# Lot Code Y2000 Lot Code Figure 15. Typical Part Marking Stencil aperture size for center ground pads should be 80% to 100% (by area) of the solder mask opening of the package. 4.3 0.5 0.4 0.05 0.05 0.15 4X 0.075 4.3 0.65 0.75 4X 0.925 Stencil and Metallization Component Outline Component Outline Solder Mask Opening 4X 0.075 SMT Pad Detail Scale: 2X 3X This Rotation 3X Rotated 180o 5X Rotated 90o CW 5X Rotated 90o CCW 4X 0.925 Stencil Aperture Top View (4.3) Pin 16 (8X 0.8 Pitch) 4.4 Pin 1 (0.9) 2 Component Outline (4X 0.9 Pitch) (0.9) (4.3) 0 4.4 2 4X 0.8 Thermal Via Array. mm on 0.6 mm pitch. Additional vias in common ground pad improve thermal and electrical performance. 4X 1.7 ∅0.3 2X 1.825 Component Outline 0.25 Typ. 2X 1.825 0 4X 0.8 Solder Mask Opening Top View Metallization Top View Notes: 1. The cross-hatched area represents the merger of the center ground pad +4 individual I/O ground pads. All I/O ground pads should have at least one via connected to internal ground planes for optimum electrical performance. 2. Thermal vias should be tented with solder mask, 30 to 35 mm Cu plating recommended. 3. All measurements are in millimeters S2895 Figure 16. PCB Layout Footprint for the SKY66100-11 4 x 4 mm MCM Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201829E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 1, 2015 13 DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM Pin 1 Indicator Pin 16 0 10X 1.9 B 4X 0.8 4 Pin 1 C Pin 1 Indicator See Detail D 10X 1.9 4X 0.8 A 0 4 4X 0.5375 16X SMT Pad 0.1 A B C B 0.9 ± 0.1 0.15 A B C 0.1 Side View Top View (0.1) Metal Pad Edges 0.2 X 0.2 0.925 0.925 0.4 ± 0.1 (0.1) Detail A Detail B Pad Scale: 2X Pad Scale: 2X 3X This rotation 3X Rotated 180° 3X Rotated 90° CW 3X Rotated 90° CCW Solder Mask Edges (0.1) Solder Mask Edges 0.4 ± 0.05 0.5 ± 0.05 Bottom View 0.4 ± 0.1 0.4 ± 0.01 Solder Mask Edges Solder Mask Openings See Detail C 0.2 A B C 4X 0.5375 A Metal Pad Edges 0.925 0.925 3X Detail C Detail D Pad Scale: 2X Solder Mask Edges Pad Scale: 2X 1X This rotation 1X Rotated 180° 1X Rotated 90° CW 1X Rotated 90° CCW All measurements are in millimeters Dimensioning and tolerancing according to ASME Y14.5M-1994 S2783 Figure 17. SKY66100-11 16-Pin MCM Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 14 June 1, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201829E DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM 2.00 ± 0.05 8.00 ± 0.10 0.30 ± 0.05 (T) 4.00 ± 0.10 ∅1.50 ± 0.10 5.50 ± 0.05 A 4.40 (Bo) A B 1.70 (Ko) 12.00 + 0.30/–0.10 B Pin 1 Indicator B 1.75 ± 0.10 ∅1.50 Min. 4.40 (Ao) A Notes: 1. Carrier tape material: black conductive polycarbonate or polystyrene. 2. Cover tape material: transparent conductive PSA. 3. Cover tape size: 9.3 mm width. 4. Ten sprocket hole pitch cumulative tolerance: ±0.20 mm. 5. Ao and Bo measured on plane 0.30 mm above the bottom of the pocket. 6. Typical ESD surface resistivity is ≤1 x 1010 Ohms/square per EIA, JEDEC tape and reel specification. 7. All measurements are in millimeters S2031 Figure 18. SKY66100-11 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201829E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 1, 2015 15 DATA SHEET • SKY66100-11: TRANSMIT/RECEIVE FEM Ordering Information Model Name SKY66100-11 TX/RX FEM (+24 dBm) SKY66100-11 TX/RX FEM (+27 dBm) Manufacturing Part Number SKY66100-11 SKY66100-11 Evaluation Board Part Number SKY66100-11-EK1 SKY66100-11-EK2 Copyright © 2012-2015 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 16 June 1, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201829E