DATA SHEET CPS CTX CSD ANT_SEL SE2431L: 2.4 GHz Front-End Module Applications Smart meters In-home appliances Logic Control Smart thermostats PA Features ANT1 Integrated: – PA with up to +24 dBm output power – LNA with programmable bypass – Antenna switching with Tx and Rx diversity function TR ANT2 Suitable for Zigbee , Bluetooth Low Energy, and Bluetooth 1.0 ® ® LNA Typical low NF: 2 dB Y1934 Operating temperature range: –40 °C to +125 °C Figure 1. SE2431L Block Diagram Single-ended 50 Ω Tx/Rx RF interface Fast switch on/off time <1 μs Supply operation: 2.0 V to 3.6 V Sleep mode current: 0.05 μA typical Small QFN (24-pin, 3.0 mm x 4.0 mm x 0.9 mm NickelPalladium-gold [NiPdAu] plated) package (MSL1, 260°C per JEDEC J-STD-020) Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. Description The SE2431L is a high-performance, fully integrated RF front-end module (FEM), suitable for Zigbee, Bluetooth Low Energy, and Bluetooth 1.0 applications. The SE2431L is designed for ease of use and maximum flexibility, with fully matched 50 Ω input and output, integrated inter-stage matching and harmonic filter, and digital controls that are compatible with 1.6 V to 3.6 V Complementary Metal Oxide Semiconductor (CMOS) levels. The RF blocks operate over a wide supply voltage range from 2.0 V to 3.6 V, which allows the SE2431L to be used in batterypowered applications over a wide spectrum of the battery discharge curve. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202410J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 29, 2015 1 CTX BOUT VCC1 CPS CSD 24 23 22 21 20 DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE B1 2 18 GND N/C 3 17 N/C N/C 4 16 ANT_SEL N/C 5 15 ANT1 T/R 6 14 GND N/C 7 13 ANT2 12 GND GND GND GND N/C 11 VCC2 10 19 9 1 8 B2 Y0587 Figure 2. SE2431L Pinout (Top View) Table 1. SE2431L Signal Descriptions Pin Name 1 B2 2 B1 3 Description Pin Name Description Connect through the bias resistor to pin 23 13 ANT2 Connect to 50 Ω antenna Connect through the bias resistor to pin 23 14 GND Connect to PCB ground N/C Not connected internally to the device 15 ANT1 Connect to 50 Ω antenna 4 N/C Not connected internally to the device 16 ANT_SEL 5 N/C Not connected internally to the device 17 N/C Not connected internally to the device 6 T/R Transmit/receive port from/to transceiver, single-ended 50 Ω 18 GND Connect to PCB ground 7 N/C Not connected internally to the device 19 VCC2 Connect to positive supply 8 N/C Not connected internally to the device 20 CSD Connect to the GPIO signal to control the SE2431L modes (see Table 8) 9 GND Connect to PCB ground 21 CPS Connect to the GPIO signal to control the SE2431L modes (see Table 8) 10 GND Connect to PCB ground 22 VCC1 Connect to positive supply. 11 GND Connect to PCB ground 23 BOUT Connect to pins 1 and 2 through the bias resistors 12 GND Connect to PCB ground 24 CTX Connect to the GPIO signal to control the antenna switch (see Table 8) Connect to the GPIO signal to control the SE2431L modes (see Table 8) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 June 29, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410J DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Electrical and Mechanical Specifications The absolute maximum ratings of the SE2431L are provided in Table 2. The recommended operating conditions are specified in Table 3, and electrical specifications are provided in Tables 4 through 7. The state of the SE2431L is determined by the logic provided in Table 8. Table 2. SE2431L Absolute Maximum Ratings (Note 1) Parameter Symbol Minimum Maximum Units Supply voltage 1 VCC1 –0.3 3.6 V Supply voltage 2 VCC2 –0.3 3.6 V –0.3 3.6 V Control pin voltages Operating temperature TOP –40 +125 C Storage temperature TSTG –40 +125 C Tx output power at ANT1 or ANT2 port into 50 Ω load POUT_TX_MAX +24 dBm Tx input power at TR port PIN_TX_MAX +6 dBm Rx input power at ANT1 or ANT2 ports PIN_RX_MAX +10 dBm Rx input power at ANT1 or ANT2 ports in bypass mode PIN_RX_BYPASS_MAX +15 dBm Thermal resistance ΘJC 40 C/W Electrostatic discharge: ESD 1000 V Human Body Model (HBM), Class 1C Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. Recommended Operating Conditions Parameter Symbol Minimum Typical Maximum Units Ambient temperature TA –40 +25 +125 C Supply voltage on VCC pins VCC1 2.0 3.0 3.6 V Supply voltage on VCC pins VCC2 2.0 3.0 3.6 V Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202410J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 29, 2015 3 DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Table 4. SE2431L Electrical Specifications: DC (Note 1) (VCC = 3 V, TA = +25 C, as Measured on the Evaluation Board [De-Embedded to the Device], Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Total supply current ICC_TX20 Tx mode POUT = +20 dBm 115 mA Total supply current ICC_TX17 Tx mode POUT = +17 dBm 90 mA Total supply current ICC_TX10 Tx mode POUT = +10 dBm 50 mA Quiescent current ICQ_TX No RF 30 mA Total supply current ICC_RX Rx mode 5 Total supply current ICC_RXBYPASS Rx Bypass mode Sleep supply current ICC_OFF No RF 0.05 7 mA 300 μA 1.0 μA Note 1: Performance is guaranteed only under the conditions listed in the above table. Table 5. SE2431L Electrical Specifications: Logic Characteristics (Note 1) (VCC = 3 V, TA = +25 C, as Measured on the Evaluation Board [De-Embedded to the Device], Unless Otherwise Noted) Max Units Logic input high voltage Parameter VIH Symbol Test Condition Min 1.6 Typical 3.6 V Logic input low voltage VIL 0 0.3 V Logic input high current IIH 1 μA Logic input low current IIL 1 μA Note 1: Performance is guaranteed only under the conditions listed in the above table. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 June 29, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410J DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Table 6. SE2431L Electrical Specifications: AC Characteristics (Note 1) (VCC = 3 V, TA = +25 C, as Measured on Skyworks SE2431L-EK1 Evaluation Board [De-Embedded to the Device], All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units 2483 MHz Transmit (Tx) Frequency range fIN 2400 Output power at ANT1 or ANT2 ports (Notes 2, 3) POUT VCC = +3.6 V, PIN = +3 dBm VCC = +3.3 V, PIN = 0 dBm VCC = +3.0 V, PIN = 0 dBm VCC = +2.7 V, PIN = 0 dBm VCC = +2.0 V, PIN = 0 dBm VCC = +3.0 V, PIN = –13 dBm Small signal gain S21 2400 MHz to 2483 MHz Small signal gain variation (Note 2) ΔS21 Gain variation across channels 2400 to 2483 MHz Harmonics (Notes 2, 4) HD2, HD3 POUT = +20 dBm Output return loss (Note 2) S22_ANT At ANT1 or ANT2 ports Input return loss (Note 2) S11 At TR port, Tx mode Rise and fall times tR (Note 6) tF (Note 7) Stability STAB CW, PIN = 0 dBm 0.1 GHz to 20.0 GHz Load VSWR = 6:1 Ruggedness RU CW, PIN = +6 dBm, Load VSWR = 10:1 dBm dBm dBm dBm dBm dBm +24.0 +22.5 +21.0 +20.5 +17.0 +10 19 22 –10 25 dB 1 dBp-p –42 dBm/MHz –5 dB –5 dB 800 ns All non-harmonically related outputs <–42.0 dBm/MHz No permanent damage Receive (Rx) Frequency range fIN 2400 Receive gain (Note 2) Rx_GAIN 10.0 Receive noise figure (Note 2) NF Third order input intercept point (Note 2) IIP3 –3 +2 dBm LNA input compression point (Note 2) IP1dB –13 –8 dBm Antenna port return loss (Note 2) S11_ANT Output return loss (Note 2) S22 Rise and fall times tR (Note 5) tF (Note 6) Bypass gain G_BP –3 Tx or Rx Bypass 1 dB input compression point IP1dB +15 At TR port, Rx mode 2483 MHz 12.5 15.0 dB 2.0 2.5 dB –10 –5 dB –10 –5 dB 800 ns –2 dB dBm Note 1: Performance is guaranteed only under the conditions listed in the above table. Note 2: 2400 MHz to 2483 MHz. Note 3: Offset EVM = 1% typical. Note 4: IEEE 802.15.4 source. Note 5: From 50% of the CTX edge to 90% of the final RF output power. Note 6: From 50% of the CTX edge to 10% of the final RF output power. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202410J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 29, 2015 5 DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Table 7. SE2431L Electrical Specifications: AC Characteristics, Diversity Antenna Function (Note 1) (VCC1 = VCC2 = 3 V, TA = +25 C, as Measured on the Evaluation Board [De-Embedded to the Device], All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Min Typical Max Units Isolation between ANT1 and ANT2 ports ISOLANTSW –20 dB Antenna 1 to antenna 2 switching time tANT1-ANT2 400 ns Note 1: Performance is guaranteed only under the conditions listed in the above table. Unused antenna port should be connected to 50 Ω. Table 8. SE2431L Logic Controls (Note 1) (VCC = 3 V, TA = +25 C, Unless Otherwise Noted) Mode CPS CSD CTX ANT_SEL All off (sleep mode) (Note 2) 0 0 0 X 1 Rx or Tx bypass mode 0 1 0 X 2 Rx LNA mode 1 1 0 X 3 Tx mode X 1 1 X ANT1 port enabled X 1 X 0 ANT2 port enabled X 1 X 1 0 Description Note 1: The logic 0 and 1 levels are compliant to VIL and VIH, respectively, as specified in Table 5. Note 2: All controls must be at logic 0 to achieve the specified sleep current. Evaluation Board Description Measure TX Performance The SE2431L Evaluation Board is used to test the performance of the SE2431L front-end module (FEM). An Evaluation Board schematic diagram is provided in Figure 3. A reference design schematic is shown in Figure 4. A photograph of the Evaluation Board is shown in Figure 5. A Bill of Materials (BOM) for the Evaluation Board is provided in Table 9. Apply an RF signal to connector J34 (TR) to monitor the 2.4 GHz amplifier performance. Monitor the output power on connector J35 (ANT1) or J32 (ANT2). Evaluation Board Setup Procedure Connect Supply 1. Connect J32, J34, and J35 to 50 Ω instruments. Terminate all unused ports (if applicable) with 50 Ω. 2. Connect the supply ground to Pin 20 of the J36 header. Measure RX Performance Apply an RF signal to connector J35 (ANT1) or J32 (ANT2) to monitor the 2.4 GHz LNA performance. Monitor the output signal on connector J34 (TR). CAUTION: Care should be taken not to overdrive the amplifier by applying too much RF on the input to the device. A suitable starting input power for the device is –20 dBm. 3. Connect 3.0 V to Pins 1, 3, and 16 of J36. 4. Refer to Table 8 for information about selecting the required RF path and for antenna port control. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 June 29, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410J DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE J36 1 3 5 7 9 11 13 15 17 19 VCC VDD C1 2.2 uF C2 2.2 uF VCC 2 4 6 8 10 12 14 16 18 20 VCC VDD CTX CPS CSD VCC2 ANT_SEL CPS C4 10 pF CSD R5 100 kΩ R6 100 kΩ CTX VCC2 R3 100 kΩ C3 100 nF PAD R1 2.2 kΩ CTX BOUT VCC1 CPS CSD 25 BOUT 24 23 22 21 20 BOUT 1 2 3 4 5 6 7 R2 1.2 kΩ VCC2 GND SE2431L DNC U1 ANT_SEL ANT1 GND ANT2 19 18 17 16 15 14 13 C5 10 pF ANT_SEL R4 100 kΩ 8 9 10 11 12 DNC GND GND GND GND J34 SMA B2 B1 DNC DNC DNC T/R DNC J35 SMA TP1 Test Point J32 SMA Y2127 Figure 3. SE2431L Evaluation Board Schematic VCC C1 2.2 uF VCC C3 10 pF CTX C2 100 nF CPS CSD T/R 6 20 21 CPS 23 22 VCC1 CSD DNC DNC ANT_SEL DNC ANT1 T/R GND DNC ANT2 8 DNC 7 GND SE2431L U1 DNC 19 18 17 16 ANT_SEL 15 ANT1 14 13 11 GND 12 GND 5 B1 GND 4 VCC2 10 3 R2 1.2 kΩ C4 10 pF B2 GND 2 9 1 CTX PAD R1 2.2 kΩ BOUT 25 BOUT 24 BOUT TP1 Test Point ANT2 Y2128 Figure 4. SE2431L Reference Design Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202410J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 29, 2015 7 DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Figure 4. SE2431L Evaluation Board Notes to Figure 4: 1. R44, R45, R43, R47, and C52 are for evaluation purposes and can be removed in the final application. 2. The Skyworks Evaluation Board contains 0 Ω resistors and footprints for non-populated components that are not shown in the schematic. Table 9. SE2431L Bill of Materials (BOM) Component Value Manufacturer Mfr Part Number Package Size Description 2.2 μF Murata GRM21BR71A225KA01L C3 100 nF Murata GRM155R71C104KA88D 0402 Monolithic ceramic capacitor C4, C5 10 pF Murata GRM1555C1H100JZ01 0402 Multilayer ceramic capacitor J32, J34, J35 SMA Johnson Components 142-0701-851 End launch SMA end launch straight jack receptacle – tab contact J36 10 x 2 Samtec TSW-110-07-G-D 100 mil 100 mil header R1 2.2 k Ω Panasonic ERJ2GEJ222 0402 Thick film chip resistor R2 1.2 k Ω Panasonic ERJ2GEJ122 0402 Thick film chip resistor R3, R4, R5, R6 100 k Ω Panasonic ERJ2GEJ104 0402 Thick film chip resistor TP1 Test Point Skyworks Solutions Printed element 0.635 mm test point TH TH 0.635 test point U1 SE2431L Skyworks Solutions SE2431L QFN400X300 Front-end module C1, C2 0805 Ceramic capacitor, 2.2 μF, 10%, X7R, 10 V Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 June 29, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410J DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Package Dimensions Package and Handling Information The PCB layout footprint for the SE2431L is provided in Figure 5. A typical part marking diagram is shown in Figure 6. Package dimensions are shown in Figure 7, and tape and reel dimensions are provided in Figure 8. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperatures during solder assembly. The SE2431L is rated to Moisture Sensitivity Level 1 (MSL1) at 260 °C, and can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202410J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 29, 2015 9 3X 1.05 3X 0.52 0 3X 1.05 4.40 2.70 3X 0.52 DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE 5X 0.54 3.40 1.70 0 0 5X 0.54 0 0.60 Typ 0.20 Typ 15X ø0.254 0.400 Typ Via Pattern (Note 4) Board Metal 4.40 4.50 1.03 Typ 2.50 0.20 Typ 0.53 Typ 3.40 3.50 1.50 0.20 Typ 0.60 Typ 0.70 Typ 0.30 Typ 0.400 Typ Package Outline 0.20 Typ 0.400 Typ Stencil Pattern (Note 5) 57% Solder Coverage on Center Pad Solder Mask Pattern (Note 6) Notes: 1. All dimensions are in millimeters. 2. Dimensions and tolerances per ASME 14.5M–1994. 3. Unless specified, dimensions are symmetrical about center lines. 4. Via hole recommendations: 0.025 mm Cu via wall plating (minimum), via holes to be filled with conductive paste and plated over. 5. Stencil recommendations: 0.10 mm stencil thickness, laser cut apertures, trapezoidal walls and rounded corners offer better paste release. 6. Solder mask recommendations: Contact board fabricator for recommended solder mask offset and tolerance. Figure 5. PCB Layout Footprint Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 June 29, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410J Y2123 DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Terminal Finish Symbol Pin 1 Indicator Skyworks Part Number Lot Code Y2124 Figure 6. SE2431L Typical Part Marking 3.00 ± 0.05 A 1.60 ± 0.05 0.85 ± 0.05 0.05 C 0.203 Ref B 0.30 x 45° 0.00–0.050 Pin 1 Indicator Pin 1 Indicator Exposed Pad 4.00 ± 0.05 2.60 ± 0.05 0.40 R0.075, Typ 24 X 0.25 Min 2X 0.05 C 25X 0.05 C Top View 0.05 C 4 C See Detail A See Detail B Bottom View Seating Plane 2X Detail B Scale 2X 4 Places Side View 0.12 ± 0.05 2X R0.075 Notes: 0.40 ± 0.05 1. Dimensions are in millimeters. 2. Dimensions and tolerances according to ASME Y14.5M-1994. 3. Unless otherwise specified, the following values apply: 0.20 ± 0.05 Decimal Tolerance: Angular Tolerance: 5 ±1/2° X.X (1 place) ± 0.1 mm X.XX (2 places) ± 0.05 mm X.XXX (3 places) ± 0.025 mm 4. Coplanarity applies to the terminals as well as all other bottom surface metallization. 5. Dimension applies to metallized terminal. If terminal tip has a radius, dimension should not be measured in that radius area. 6. Unless specified, dimensions are symmetrical about center lines. R0.075 Detail A Scale 2X 20 Places 0.07 0.05 C A B C 0.28 ± 0.05 0.20 ± 0.05 5 0.07 0.05 0.40 ± 0.05 C A B C Y2122 Figure 7. SE2431L Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202410J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 29, 2015 11 DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE 8.00 ∅1.5 +0.1/–0.0 4.00 (Note 1) 1.75 ± 0.10 ∅1.50 Min. A 5.50 ± 0.05 (Note 3) R0.3 Max. 4.40 12.0 ± 0.30 2.00 ± 0.05 (Note 3) 0.30 ± 0.05 A 0.12 1.10 Pin 1 Indicator 3.40 A Notes: 1. 10 sprocket hole pitch cumulative tolerance ±0.2. 2. Camber in compliance with EIA 481. 3. Pocket position relative to sprocket hole measured as true position of pocket, not pocket hole. 4. All measurements are in millimeters. 0.12 R0.25 Figure 8. SE2431L-R Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 June 29, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202410J S2742 DATA SHEET • SE2431L: 2.4 GHz FRONT-END MODULE Ordering Information Model Name SE2431L: 2.4 GHz Front-End Module Manufacturing Part Number SE2431L Evaluation Board Part Number SE2431L-EK1 Copyright © 2012-2015 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202410J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 29, 2015 13