Data Sheets - Skyworks Solutions, Inc.

PRELIMINARY DATA SHEET
SKY13484: 0.6-2.7 GHz DP12T (SP7T/SP5T) Receive Diversity
Switch with MIPI RFFE Interface for Carrier Aggregation
Applications
• Carrier aggregation receive diversity systems (low band/high
band)
• Embedded data cards
Features
• Low insertion loss, optimized for low and high bands
• Excellent Band 13 2nd harmonic performance (<–81 dBm)
• Excellent Band 17 3rd harmonic performance (<–100 dBm)
• Dual antenna ports can be connected externally to a low
band/high band diplexer
• Integrated, programmable MIPI interface using separate
registers for low and high bands
• Small MCM (22-pin, 2.5 x 2.9 x 0.8 mm) package (MSL3,
260 °C per JEDEC J-STD-020)
Figure 1. SKY13484 Block Diagram
Switching is controlled by an integrated MIPI decoder. The two
switches can be configured independently. There are separate
registers for low and high bands. No external DC blocking
capacitors are required on the RF paths as long as no DC voltage
is applied to those paths.
Description
The SKY13484 is a Single Pole, Five Throw (SP5T) and SinglePole, Seven Throw (SP7T) Mobile Industry Processor Interface
(MIPI) controlled antenna switch designed specifically for receive
diversity in carrier aggregation applications.
The SP5T switch is optimized for the low band and the SP7T
switch is optimized for the high band. Using advanced switching
technologies, the SKY13484 maintains low insertion loss and high
isolation for all switching paths. The high linearity performance
and low insertion loss achieved by the SKY13484 makes it an
ideal choice for carrier aggregation applications. The switch also
exhibits excellent 2nd/3rd Order Intermodulation Distortion
(IMD2/IMD3) performance.
The SKY13484 is manufactured in a compact,
2.5 x 2.9 x 0.8 mm, 22-pin surface mount Multi-Chip Module
(MCM) package.
A functional block diagram is shown in Figure 1. The pin
configuration and package are shown in Figure 2. Signal pin
assignments and functional pin descriptions are provided in
Table 1.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202745A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2013
1
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
Figure 2. SKY13484 Pinout – 22-Pin MCM
(Top View)
Table 1. SKY13484 Signal Descriptions
Pin #
Name
Description
Pin #
Name
Description
1
TRX6
High band transmit/receive port 6
12
TRX1
Low band transmit/receive port 1
2
TRX7
High band transmit/receive port 7
13
TRX2
Low band transmit/receive port 2
3
TRX8
High band transmit/receive port 8
14
TRX3
Low band transmit/receive port 3
4
TRX9
High band transmit/receive port 9
15
TRX4
Low band transmit/receive port 4
5
TRX10
High band transmit/receive port 10
16
TRX5
Low band transmit/receive port 5
6
TRX11
High band transmit/receive port 11
17
GND
Ground
7
TRX12
High band transmit/receive port 12
18
VDD
DC power supply
8
GND
Ground
19
VIO
Interface supply voltage
9
ANT_HB
High band antenna port
20
SDATA
Data
10
ANT_LB
Low band antenna port
21
SCLK
Clock
11
GND
Ground
22
GND
Ground
Note:
Bottom ground paddles must be connected to ground.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
2
February 22, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202745A
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
Table 2. SKY13484 Absolute Maximum Ratings
Parameter
Symbol
Minimum
Maximum
Units
6
V
Supply voltage
VDD
Digital control signal
VIO
2
V
SCLK port voltage
SCLK
VIO
V
SDATA port voltage
SDATA
VIO
V
RF input power
PIN
+31
dBm
Storage temperature
TSTG
–55
+150
°C
Operating temperature
TOP
–30
+90
°C
Note:
Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other
parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device.
CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device
must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body
or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times.
Electrical and Mechanical Specifications
The absolute maximum ratings of the SKY13484 are provided in
Table 2. Electrical specifications are provided in Tables 3 and 4.
IMD2 and IMD3 test conditions for various frequencies are listed in
Tables 5 and 6, respectively.
Triple Beat Ratio frequencies are listed in Table 7.
Figure 3 illustrates the test setup used to measure intermodulation
products. This industry standardized test is used to simulate the
WCDMA linearity of the antenna switch. A +20 dBm Continuous
Wave (CW) signal, fFUND, is sequentially applied to the TRX1
through TRX12 ports, while a –15 dBm CW blocker signal, fBLK, is
applied to the ANT port.
Table 8 describes the register content and programming
read/write sequences. Refer to the MIPI Alliance Specification for
RF Front-End Control Interface (RFFE), v1.10 (26 July 2011) for
additional information on MIPI programming sequences and MIPI
bus specifications.
Figure 4 provides the timing diagram for register write
commands.
Register descriptions and programming information is provided in
Table 9.
Tables 10 and 11 provide the Register_0 and Register_1 logic,
respectively.
The resulting 3rd Order Intermodulation Distortion (IMD3), fRX, is
measured over all phases of fFUND. The SKY13484 exhibits
exceptional performance for all TRXx ports.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202745A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2013
3
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
Table 3. SKY13484 RF Electrical Specifications (Note 1)
(VDD = 2.85 V, TOP = +25 °C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Operating frequency
f
Insertion loss
IL
Test Condition
Min
Typical
0.6
Max
Units
2.7
GHz
TRX1 to TRX5, low band:
704 MHz
0.40
0.50
dB
824 to 960 MHz
0.45
0.55
dB
1710 to 2170 MHz
0.6
0.65
dB
2170 to 2690 MHz
0.7
0.80
dB
TRX6 to TRX12, high
band:
Isolation
Iso
Isolation
Iso
ANT_LB to any “off” TRXx
low band port:
Up to 704 MHz
28
30
dB
Up to 960 MHz
26
28
dB
Up to 1990 MHz
26
28
dB
Up to 2170 MHz
24
26
dB
Up to 2690 MHz
22
25
dB
25
30
dB
ANT_HB to any “off” TRXx
high band port:
Isolation
Iso
Any low band port (TRX1
to TRX5) to any high band
port (TRX6 to TRX12) up
to 960 MHz
“On” state match
VSWR
Up to 2.7 GHz
2nd Order Intermodulation Distortion
IMD2
See Table 5
–105
–110
dBm
3rd Order Intermodulation Distortion
IMD3
See Table 6
–105
–110
dBm
Triple Beat Ratio (650 to 900 MHz)
TBR
See Table 7
+51
+81
dBc
dBm
nd
rd
1.5:1
Low band 2 and 3 harmonic
2fo, 3fo
TRX1 to TRX5,
PIN = +24 dBm,
f = 900 MHz
–65
Low band 2nd and 3rd harmonic
2fo, 3fo
TRX1 to TRX5,
PIN = +24 dBm,
f0 = 900 MHz,
VSWR = 5:1
–55
dBm
Band 13 2nd harmonic
2fo
TRX1 to TRX5,
PIN = +15 dBm,
f0 = 782 MHz
–81
dBm
Band 17 3rd harmonic
3fo
TRX1 to TRX5,
PIN = +15 dBm,
f = 707 MHz
–105
Turn-on time
tON
From application of VDD
and VIO
Wake up time
tW
From isolation state
Switching speed
tS
Any state to any other
state
–100
dBm
20
μs
2
5
μs
2
5
μs
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
4
–
February 22, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202745A
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
Table 4. SKY13484 DC Electrical Specifications (Note 1)
(VDD = 2.85 V, VIO = 1.8 V, TOP = +25 °C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Supply voltage
VDD
Supply current, active mode
IDD
Interface supply voltage level
VIO
Interface signal:
High
Low
SDATA
Test Condition
Min
Typical
Max
2.50
2.85
6.00
V
50
100
μA
1.80
1.95
V
0.3 × VIO
V
V
10
5
μA
μA
1.65
0.7 × VIO
Control current:
High
Low
Units
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Table 5. IMD2 Test Conditions
Band
Transmit
Frequency
(MHz)
Transmit Power
(dBm)
1
1950.0
190
4090
2140.0
2
1880.0
80
3840
1960.0
4
1732.0
400
3864
+20
Frequency
Blocker, Low
(MHz)
Frequency
Blocker, High
(MHz)
Power Blocker
(dBm)
Receive Frequency
(MHz)
2132.0
–15
5
836.5
45
1718
7
2535.0
120
5187
2655.0
881.5
8
897.0
45
1839
942.0
Table 6. IMD3 Test Conditions
Band
Transmit Frequency
(MHz)
Transmit Power
(dBm)
1
1950.0
1760.0
2140.0
2
1880.0
1800.0
1960.0
4
1732.0
1332.0
+20
Frequency Blocker
(MHz)
Power Blocker
(dBm)
Receive Frequency
(MHz)
2132.0
–15
5
836.5
7
2535.0
2415.0
791.5
2655.0
881.5
8
897.0
852.0
942.0
Table 7. Triple Beat Ratio Frequencies and Power Levels
Band
Transmit
Frequency 1
(MHz)
Transmit Power
1
(dBm)
Transmit
Frequency 2
(MHz)
Transmit Power
2
(dBm)
Frequency
Blocker ANT
(MHz)
Power Blocker
(dBm)
Triple Beat Product
Frequency
(MHz)
2
1880.0
+21.5
1881.0
+21.5
5
836.5
+21.5
881.5
+21.5
1960.0
–30
1960.0 ± 1
881.5
–30
881.5 ± 1
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202745A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2013
5
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
Figure 3. Typical 3rd Order Intermodulation Test Setup
Table 8. Command Sequence Bit Definitions
Extended Operation
Type
SSC
C11C8
Reg_0
Write,
Short
Command
Y
SA[3:0]
1b
Data[6:5]
Data[4]
Data{3:0]
Y
Y
–
–
–
–
–
–
Reg_0
Write,
Long
Command
Y
SA[3:0]
0
10b
Addr[4]
Addr[3:0]
Y
–
Data[7:0]
–
–
–
Y
Y
Reg_1
Write
Y
SA[3:0]
0
10b
Addr[4]
Addr[3:0]
Y
–
Data[7:0]
–
–
–
Y
Y
Reg
Read
Y
SA[3:0]
0
11b
Addr[4]
Addr[3:0]
Y
Y
Data[7:0]
–
–
–
Y
Y
Legend:
SSC = Sequence start command
C = Command frame bits
C7
C6-C5
C4
DA = Data/address frame bits
BPC = Bus park cycle
C3-C0
Parity
Bits
BPC
DA7(1)DA0(1)
Parity
Bits
BPC
DA7(n)DA0(n)
Parity
Bits
BPC
BC = Byte count (# of consecutive addresses)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
6
February 22, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202745A
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
Figure 4. Register Write Command Timing Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202745A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2013
7
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
Table 9. Register Description and Programming (1 of 2)
Register
Parameter
Name
Address
(Hex)
Register_0
0000
MODE_CTRL
Register_1
0001
MODE_CTRL
Default
(Binary)
Description
Bits[6:0]:
0000000
See Table 10 for logic
Bits[7:0]:
00000000
See Table 11 for logic
PWR_MODE
Bits[7:6]:
01
00 = Normal operation (active)
01 = Default settings (startup)
10 = Low power (low power)
11 = Reserved
Trigger_Mask_2
Bit[5]:
0
If this bit is set, trigger 2 is disabled. When all triggers are disabled,
if writing to a register that is associated with trigger 2, the data goes
directly to the destination register.
Trigger_Mask_1
PM_TRIG
(Note 1)
001C
Bit[4]:
0
If this bit is set, trigger 1 is disabled. When all triggers are disabled,
if writing to a register that is associated with trigger 1, the data goes
directly to the destination register.
Trigger_Mask_0
Bit[3]:
0
If this bit is set, trigger 0 is disabled. When all triggers are disabled,
if writing to a register that is associated with trigger 0, the data goes
directly to the destination register.
Trigger_2
Bit[2]:
0
If this bit is set, data is loaded into the trigger 2 registers.
Trigger_1
Bit[1]:
0
If this bit is set, data is loaded into the trigger 1 registers
(unsupported).
Trigger_0
Bit[0]:
0
If this bit is set, data is loaded into the trigger 0 registers
(unsupported).
PRODUCT_ID
001D
PRODUCT_ID
Bits[7:0]:
This is a read-only register. However, during the programming of the
Unique Slave Identifier (USID), a write command sequence is
performed on this register but the value is not changed.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
8
February 22, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202745A
01010000
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
Table 9. Register Description and Programming (2 of 2)
Register
MANUFACTURER_ID
Parameter
001E
Default
(Binary)
Description
MANUFACTURER_ID
Bits[7:0]:
10100101
Read-only register
Reserved
Bits[7:6]:
00
Reserved
MAN_USID
001F
MANUFACTURER_ID
Bits[5:4]:
01
Read-only register
USID
Bits[3:0]:
1011
Programmable USID. A write to these bits programs the USID.
Note 1: Unlike the complete independence between triggers 0, 1, and 2, and also between the associated trigger masks 0, 1, and 2, respectively, as described in the MIPI RFFE Specification,
this device uses additional interactions between the provided trigger functions.
The delayed application of updated data to all triggerable registers in this device may be accomplished using any of the three triggers (0, 1, or 2), provided that the particular trigger
used is not currently masked off. If multiple triggers are enabled, any or all of those are sufficient to cause the data to be transferred from shadow registers to destination registers for
all triggerable registers in the device.
It is also necessary to disable all three triggers (i.e., set all three trigger masks) to ensure that data written to any triggerable register will immediately be written to the destination
register at the conclusion of the RFFE command sequence where the data is written.
Table 10. Register_0 Truth Table (High Band)
State
Mode
Register 0 Bits
D7
D6
D5
D4
D3
D2
D1
D0
1
Isolation (default)
x
x
x
x
x
0
0
0
2
TRX6
x
x
x
x
x
0
0
1
3
TRX7
x
x
x
x
x
0
1
0
4
TRX8
x
x
x
x
x
0
1
1
5
TRX9
x
x
x
x
x
1
0
0
6
TRX10
x
x
x
x
x
1
0
1
7
TRX11
x
x
x
x
x
1
1
0
8
TRX12
x
x
x
x
x
1
1
1
Table 11. Register_1 Truth Table (Low Band)
State
Mode
Register 1 Bits
D7
D6
D5
D4
D3
D2
D1
D0
1
Isolation (default)
x
x
x
x
x
0
0
0
2
TRX1
x
x
x
x
x
0
0
1
3
TRX2
x
x
x
x
x
0
1
0
4
TRX3
x
x
x
x
x
0
1
1
5
TRX4
x
x
x
x
x
1
0
0
6
TRX5
x
x
x
x
x
1
0
1
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202745A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2013
9
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
Evaluation Board Description
Package and Handling Information
The SKY13484 Evaluation Board is used to test the performance
of the SKY13484 DP12T (SP7T/SP5T) Switch. An Evaluation Board
schematic diagram is provided in Figure 5. An assembly drawing
for the Evaluation Board is shown in Figure 6.
Since the device package is sensitive to moisture absorption, it is
baked and vacuum packed before shipping. Instructions on the
shipping container label regarding exposure to moisture after the
container seal is broken must be followed. Otherwise, problems
related to moisture absorption may occur when the part is
subjected to high temperature during solder assembly.
Package Dimensions
The PCB layout footprint for the SKY13484 is provided in Figure 7.
Typical case markings are shown in Figure 8. Package
dimensions for the 22-pin MCM are shown in Figure 9, and tape
and reel dimensions are provided in Figure 10.
The SKY13484 is rated to Moisture Sensitivity Level 3 (MSL3) at
260 °C. It can be used for lead or lead-free soldering. For
additional information, refer to the Skyworks Application Note,
PCB Design and SMT Assembly/Rework Guidelines for MCM-L
Packages, document number 101752.
Care must be taken when attaching this product, whether it is
done manually or in a production solder reflow environment.
Production quantities of this product are shipped in a standard
tape and reel format.
Figure 5. SKY13484 Evaluation Board Schematic
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
10
February 22, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202745A
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
Figure 6. SKY13484 Evaluation Board Assembly Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202745A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2013
11
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
Figure 7. SKY13484 PCB Layout Footprint
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
12
February 22, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202745A
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
*** TBD ***
Figure 8. Typical Part Markings
(Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202745A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2013
13
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
Figure 9. SKY13484 22-Pin MCM Package Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
14
February 22, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202745A
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
*** TBD ***
Figure 10. SKY13484 Tape and Reel Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202745A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2013
15
PRELIMINARY DATA SHEET • SKY13484 DP12T (SP7T/SP5T) RECEIVE DIVERSITY SWITCH WITH MIPI RFFE INTERFACE
Ordering Information
Model Name
SKY13484 0.4-2.7 GHz SP5T + SP7T Receive Diversity
Switch with MIPI RFFE Interface
Manufacturing Part Number
SKY13484
Evaluation Board Part Number
SKY13484-EVB
Copyright © 2013 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by
Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of
Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands
and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com,
are incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
16
February 22, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202745A