DATA SHEET SE2567L: 5 GHz Power Amplifier with Power Detector Preliminary Information Applications Product Description The SE2567L is a 5GHz power amplifier offering high linear power for wireless LAN applications. It incorporates a power detector for closed loop monitoring and control of the output power. DSSS 5 GHz WLAN (IEEE802.11a) Access Points, PCMCIA, PC cards Features High output power amplifier 19dBm Integrated 50ohm input and output match Integrated power amplifier enable pin (VEN) Buffered, temperature compensated power detector 3% EVM, @19dBm, 64 QAM, 54 Mbps 30 dB Gain Lead Free and RoHS compliant, halogen free package 16 pin 3 mm x 3 mm x 0.9 mm QFN Ordering Information Part Number Package Remark SE2567L SE2567L-R SE2567L-EK1 16 Pin QFN 16 Pin QFN Evaluation Kit Samples Tape and Reel Standard The SE2567L offers a high level of integration for a simplified design, providing quicker time to market and higher application board production yield. The device integrates the input match, the inter-stage match, a temperature compensated, load insensitive power detector with 15dB of dynamic range and a 3.8GHz notch filter. Two external components are required to complete the design. For wireless LAN applications, the device meets the requirements of IEEE802.11a and delivers approximately 19dBm of linear output power. The SE2567L integrates the reference voltage generator, allowing for a true CMOS compatible digital EN (enable) function to turn the power amplifier on and off. Functional Block Diagram Figure 1: Functional Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202425A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 1 DATA SHEET SE2567L: 5 GHz Power Amplifier with Power Detector Preliminary Information VCC1 VCC2 GND VCC3 Pin Out Diagram 16 15 14 13 GND 1 12 GND Ground Paddle RF IN 2 11 RF OUT 5 6 7 8 DET 9 NC GND VCC0 4 NC 10 GND EN GND 3 Figure 2: SE2567L Pin-Out Diagram Pin Out Description Pin No. Name Description 1 GND Ground 2 RFin Power Amplifier RF input, DC block required 3 GND Ground 4 VCC0 Bias Circuit Supply Voltage 5 EN Reference Voltage and Power Amplifier Enable 6 NC No Connect 7 GND Ground 8 DET Analog Power Detector Output 9 NC No Connect 10 GND Ground 11 RFout Power Amplifier RF Output, no DC block required 12 GND Ground 13 VCC3 Third Stage Supply Voltage 14 GND Ground 15 VCC2 Second Stage Supply Voltage 16 VCC1 First Stage Supply Voltage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202425A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 2 DATA SHEET SE2567L: 5 GHz Power Amplifier with Power Detector Preliminary Information Absolute Maximum Ratings These are stress ratings only. Exposure to stresses beyond these maximum ratings for a long period of time may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected workstations. Symbol Definition Min. Max. Unit Supply Voltage on pins VCC0, VCC1 -0.3 3.6 Supply Voltage on pins VCC2, VCC3 -0.3 4.9 DC input on EN -0.3 3.6 V - 12 dBm VCC EN V RFIN RF Input Power, RFout into 50Ω match TSTG Storage Temperature Range -40 150 °C ESD HBM JEDEC JESD22-A114 all pins - 500 V Min. Max. Unit Supply Voltage (VCC0, VCC1) 3.0 3.6 Supply Voltage (VCC2, VCC3) 3.0 4.5 Ambient Temperature -40 85 Recommended Operating Conditions Symbol Parameter VCC TA V °C DC Electrical Characteristics Conditions: VCC = VEN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2567L-EV1 evaluation board, unless otherwise noted. Symbol Parameter ICC-802.11a Supply Current IQC Conditions Min. Typ. Max. Unit POUT = 19 dBm, 54 Mbps, 64 QAM - 220 - mA Quiescent Current No RF - 150 - mA IOFF Supply Current VEN = 0 V, No RF - 10 100 μA VENH Logic High Voltage - 1.6 - 3.6 V VENL Logic Low Voltage - 0 - 0.5 V IENH Input Current Logic High Voltage - - 300 - μA IENL Input Current Logic Low Voltage - - <1 - μA ZEN Enable pin input impedance Passive Pull Down 10 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202425A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 kΩ 3 DATA SHEET SE2567L: 5 GHz Power Amplifier with Power Detector Preliminary Information AC Electrical Characteristics 802.11a AC Electrical Characteristics Conditions: VCC = VEN = 3.3V, f = 5.4 GHz, TA = 25 °C, as measured on Skyworks Solutions’ SE2567L-EV1 evaluation board, unless otherwise noted Symbol fL-U POUT Parameter Conditions Min. Typ. Max. Unit - 4.9 - 5.9 GHz VCC0,1,2,3 = 3.3V - 19 - VCC0,1 = 3.3V; VCC2,3 = 4.5V - 21.5 - Frequency Range Output Power, 54 Mbps OFDM signal, 64 QAM, 3% EVM dBm P1dB Output 1dB compression point No modulation - 25 - dBm S11 Input Return Loss PIN = -25 dBm 6 - - dB S21 Small Signal Gain PIN = -25 dBm - 30 - dB Small Signal Gain Variation Gain variation over single 40MHz channel Gain Variation over band - 0.5 - ΔS21 - 2.0 4.0 Out of Band Gain Gain at 3.8GHz - - 10 dB POUT = 19.0dBm @3.3V or POUT = 21.5dBm @4.5V - -50 - dBm/MHz Harmonic - -50 - dBm/MHz - 0.5 - us S21_3.8 2f 3f tr , tf STAB RU Rise and Fall Time - dB Stability POUT = 19 dBm, 54 Mbps, 64 QAM, VSWR = 6:1, all phases All non-harmonically related outputs less than -50 dBc/100 kHz Ruggedness: Tolerance to output load mismatching PIN = 12 dBm, VCC2 = VCC3 = 4.5V, 54 Mbps 64 QAM, 64 QAM, VSWR = 6:1, all phases No damage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202425A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 4 DATA SHEET SE2567L: 5 GHz Power Amplifier with Power Detector Preliminary Information Power Detector Conditions: VCC = VEN = 3.3V, f = 5.4 GHz, TA = 25 °C, as measured on Skyworks Solutions’ SE2567L-EV1 evaluation board, unless otherwise noted Symbol Parameter Conditions Min. Typ. Max. Unit - 0 - P1dB dBm PDR POUT detect range VDET Detector voltage, POUT = 20dBm Measured into 26.5KΩ - 1.00 - V VDET Detector voltage, POUT = 5dBm Measured into 26.5KΩ - 0.33 - V PDZOUT Output Impedance - - 2.5 - KΩ PDZLOAD DC load impedance - - 26.5 - KΩ - 2.0 - MHz LPF Power detector low pass filter 3dB corner frequency Measured into 26.5KΩ Figure 3: SE2567L Power Detector Characteristic Detector Voltage (V) SE2567L Detector Characteristics 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 4 6 8 10 12 14 16 18 20 22 Output Power (dBm) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202425A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 5 DATA SHEET SE2567L: 5 GHz Power Amplifier with Power Detector Preliminary Information Package Diagram 16 15 14 13 13 14 15 16 1 12 12 1 2 11 11 2 3 10 10 3 4 9 9 4 5 6 7 8 8 TOP VIEW 7 6 5 BOTTOM VIEW Figure 4: SE2567L Package Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202425A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 6 DATA SHEET SE2567L: 5 GHz Power Amplifier with Power Detector Preliminary Information Recommended Land and Solder Patterns Figure 5: SE2567L Recommended Land and Solder Pattern Package Handling Information Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SE2597L is capable of withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For details on both attachment techniques, precautions, and handling procedures recommended, please refer to: “Quad Flat No-Lead Module Solder Reflow & Rework Information”, Document Number QAD-00045 “Handling, Packing, Shipping and Use of Moisture Sensitive QFN”, Document Number QAD-00044 Branding Information Caution! Class 1B ESD sensitive device Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202425A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 7 DATA SHEET SE2567L: 5 GHz Power Amplifier with Power Detector Preliminary Information Pin 1 Identifier Pin 1 Part SiGe 2567L Lot Code Lot Figure 4: SE2567L Branding Tape and Reel Information Parameter Devices Per Reel Reel Diameter Tape Width Value 3000 13 inches 12 millimeters Figure 5: SE2567L-R Tape and Reel Information Document Change History Revision Date Notes 1.0 August 2, 2009 Created 1.1 February 3, 2010 Updated off-state leakage current. Added reference to “Class 0 ESD Device Handling” 1.2 March 30, 2010 Updated to include 4.5V operation 1.3 November 15, 2010 Updated Ruggedness Specification Updated Recommended Operating Temperature Updated ESD rating Updated marking diagram to remove terminal finish indicator 1.4 April 10, 2012 Updated with Skyworks logo and disclaimer statement Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202425A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 8 DATA SHEET SE2567L: 5 GHz Power Amplifier with Power Detector Preliminary Information Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202425A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 9