DATA SHEET SE2568L: 2.4 GHz High Efficiency Wireless LAN PA Applications Product Description The SE2568L is a complete 802.11 b/g WLAN discrete power amplifier. The device provides all the functionality of the power amplifier, power detector, filter, associated input, inter-stage and output matching in an ultra-compact 2mm x 2mm x 0.9mm form factor. IEEE802.11b DSSS WLAN IEEE802.11g OFDM WLAN Embedded, SiP modules Features Dual Mode IEEE802.11b & IEEE802.11g Integrated PA, digital bias control, 50Ω input and output match, 3.2GHz TX Filter. Integrated harmonic filter. Integrated load insensitive Power Detector, with <1dB error at 2:1 mismatch 20 dBm Output Power, 802.11b, 11 Mbps, ACPR <-30 dBc 18dBm @ 3.0 % EVM, 802.11g, 54 Mbps 2.3 V to 4.8 V direct to battery supply Lead free, Halogen free, ROHS compliant , 2 x2x0.9 mm QFN package, MSL 1 The SE2568L is designed for ease of use, with all the critical input and output matching integrated. The SE2568L includes a transmitter power detector with 20 dB of dynamic range and a digital Enable for power on/off control. Harmonic filters and an input 3.2GHz LO rejection filter are integrated on-chip. The power ramp rise/fall time is 0.7 μs typical. Ordering Information Part No. Package Remark SE2568L SE2568L-R SE2568L-EK1 8 pin QFN 8 pin QFN N/A Samples Tape and Reel Evaluation kit Functional Block Diagram EN VCC VCC2 Bias Circuitry RF IN 50ohm Match 50ohm Match & harmonic Filter 3.2GHz Filter RF Out Detector Pdet Figure 1: Functional Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202426E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 12, 2014 1 DATA SHEET SE2568L: 2.4 GHz High Efficiency Wireless LAN PA Pin Out Diagram RF IN 1 8 EN GND 2 7 DET Ground Paddle GND 3 6 VCC RF OUT 4 5 VCC2 Y0818 Figure 2: SE2568L Pin Out (Top View Through Package) Pin Out Description Pin No. Name Description 1 RF In RF Input (No DC voltage on the pin, but DC short to ground) 2 GND Ground 3 GND Ground 4 RF Out 5 VCC2 Final Stage Supply Voltage (May attach directly to battery) 6 VCC First Stage Supply Voltage (May attach directly to battery) 7 DET Power Detector Output 8 EN Power Amplifier Enable Die paddle GND RF Output (No DC voltage on the pin, DC open to ground) Ground Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202426E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 12, 2014 2 DATA SHEET SE2568L: 2.4 GHz High Efficiency Wireless LAN PA Absolute Maximum Ratings These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected workstations. Symbol Min. Max. Unit Supply Voltage on VCC -0.3 5.5 V EN DC input on EN -0.3 4.0 V TX RF Input Power. ANT terminated in 50Ω match - 12.0 dBm TA Operating Temperature Range -40 85 °C Storage Temperature Range -40 150 °C - 500 V VCC TSTG ESD HBM Definition JEDEC JESD22-A114, all pins Recommended Operating Conditions Symbol TA VCC Parameter Min. Typ. Max. Unit Ambient temperature -40 25 85 °C Supply voltage, nominal operation 2.7 3.3 5.0 Supply voltage, output power reduced by 2dB typ 2.3 2.7 - V DC Electrical Characteristics Conditions: VCC = 3.3V (default) or VCC = 5.0V (as noted), EN = 3.3V, TA = 25 C, as measured on Skyworks Solutions’ SE2568L-EK1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit ICC-G Total Supply Current 54 Mbps OFDM signal, 64QAM 18dBm, VCC = 3.3V 20.5dBm, VCC = 5.0V - 135 150 150 170 mA ICC-N Total Supply Current 802.11n, MCS7 17dBm, VCC = 3.3V 19dBm, VCC = 5.0V - 115 130 130 150 mA ICC-B Total Supply Current 11 Mbps CCK signal, BT = 0.45 20dBm, VCC = 3.3V 22dBm, VCC = 5.0V - 160 175 190 210 mA ICQ Total Supply Current - 90 100 125 140 mA ICC_OFF Total Supply Current - 1 10 μA No RF VCC = 3.3V VCC = 5V EN = 0 V, No RF Applied Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202426E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 12, 2014 3 DATA SHEET SE2568L: 2.4 GHz High Efficiency Wireless LAN PA Logic Characteristics Conditions: VCC = 3.3V (default) or VCC = 5.0V (as noted), EN = 3.3V, TA = 25 C, as measured on Skyworks Solutions’ SE2568L-EK1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VENH Logic High Voltage (Module On) - 1.8 - 3.6 V VENL Logic Low Voltage (Module Off) - 0 - 0.4 V IENH Input Current Logic High Voltage - - 2 10 μA IENL Input Current Logic Low Voltage - - 2 10 μA Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202426E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 12, 2014 4 DATA SHEET SE2568L: 2.4 GHz High Efficiency Wireless LAN PA AC Electrical Characteristics 802.11g Transmit Characteristics Conditions: VCC = 3.3V (default) or VCC = 5.0V (as noted), EN = 3.3V, TA = 25 C, as measured on Skyworks Solutions’ SE2568L-EK1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FIN Parameter Condition Min. Typ. - 2400 - 2500 54Mbps, OFDM, 64 QAM, EVM = 3% +17 +18 - 11Mbps, CCK, BT = 0.45, Mask +20 +22 - 54Mbps, OFDM, 64 QAM, EVM = 3% +19 +21 - 11Mbps, CCK, BT = 0.45, Mask +22 +24 - Frequency Range Output Power, 3.3V Pout Output Power, 5.0V Max. Unit MHz dBm P1dB P1dB - +22.5 +25.0 - dBm S21 Small Signal Gain - 25 28 29 dB Small Signal Gain Variation Gain variation over single 20MHz channel Gain Variation over band - 0.5 - ∆S21 - - 1.1 - - 15 dB 20dBm, 3.3V 22dBm, 5.0V - -50 -45 dBm/MHz 20dBm, 3.3V 22dBm, 5.0V - -50 -48 -45 -43 dBm/MHz S21 3.2 Gain @ limit at Ref3206 to 3312 MHz vco spur frequency 2f Harmonics 1 Mbps, BPSK, 3f tdr, tdf S11 STAB RU dB Delay & rise/fall Time 50 % of VEN edge and 90/10 % of final output power level - 0.7 - μs Input Return Loss - 7 10 - dB Stability CW, POUT = 20 dBm, VCC = 3.3V 0.1 GHz – 20 GHz Load VSWR = 10:1 All non-harmonically related outputs less than -42 dBm/MHz Ruggedness PIN = 12dBm, VCC = 3.3V Load VSWR = 10:1 No permanent damage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202426E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 12, 2014 5 DATA SHEET SE2568L: 2.4 GHz High Efficiency Wireless LAN PA Power Detector Characteristics Conditions: VCC = 3.3V (default) or VCC = 5.0V (as noted), EN = 3.3V, TA = 25 C, as measured on Skyworks Solutions’ SE2568L-EK1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Condition VCC = 3.3V VCC = 5V Unit Min. Typ. Max. Min. Typ. 2400 - 2500 2400 - 2500 MHz 0 - 23 0 - 23 dBm - - 1 - - 1 - kΩ Output Voltage, POUT = No RF Measured into 1MΩ 0.55 0.12 0.17 0.55 0.12 0.17 V PDVp18 Output Voltage, POUT = 18 dBm CW Measured into 1MΩ 0.50 0.60 0.75 0.50 0.55 0.75 V PDVp20 Output Voltage, POUT = 20 dBm CW Measured into 1MΩ 0.65 0.75 0.98 0.65 0.70 0.98 V PDVp23 Output Voltage, POUT = 23 dBm CW Measured into 1MΩ 0.95 NA 1.32 0.95 1.00 1.32 V LPF-3dB Power detect low pass filter -3dB corner frequency Measured into 1MΩ 260 290 400 270 290 400 kHz FOUT Frequency Range PDR Power detect range, CW PDZsrc PDVNoRF Measured at ANT DC source impedance on PD_OUT 3.3V Operation 5.0V Operation Power Detector Response Power Detector Response 2400 2450 2400 MHz 2500 2450 MHz 2500 MHz 1 1 0.8 VDET (V) 0.8 VDET (V) Max. 0.6 0.4 0.6 0.4 0.2 0.2 0 0 3 5 7 9 11 13 15 17 Output Power (dBm) 19 21 23 25 3 5 7 9 11 13 15 17 Output Power (dBm) 19 21 23 25 Figure 3: SE2568L Power Detector Characteristics Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202426E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 12, 2014 6 DATA SHEET SE2568L: 2.4 GHz High Efficiency Wireless LAN PA Package Diagram This package is Pb free and RoHS compliant. The product is rated MSL1. 1 8 8 1 2 7 7 2 3 6 6 3 4 5 5 4 TOP VIEW BOTTOM VIEW Figure 4: SE2568L Package Diagram Recommended Land Pattern 1 8 1 8 1 8 2 7 2 7 2 7 3 6 3 6 3 6 4 5 4 5 4 5 Figure 5: SE2568L Package Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202426E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 12, 2014 7 DATA SHEET SE2568L: 2.4 GHz High Efficiency Wireless LAN PA Branding Information Pin 1 Part Lot Code 2568 Lot Figure 6: SE2568L Branding and Pin 1 Location (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202426E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 12, 2014 8 DATA SHEET SE2568L: 2.4 GHz High Efficiency Wireless LAN PA Package Handling Information Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SE2568L is capable of withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For details on both attachment techniques, precautions, and handling procedures recommended, please refer to: “QFN solder reflow and rework information application note”, Document Number QAD-00045 “Handling, packing, shipping and use of moisture sensitive QFN application note”, Document Number QAD-00044 Caution! Class 1B ESD sensitive device Tape and Reel Information Parameter Devices Per Reel Reel Diameter Tape Width Value 3000 7 inches 12 millimeters Figure 8: SE2568L Tape and Reel Information Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202426E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 12, 2014 9 DATA SHEET SE2568L: 2.4 GHz High Efficiency Wireless LAN PA Document Change History Revision Date Notes 1.0 10/13/2009 Created 1.1 11/16/2009 Corrected label error on Detector plot 1.2 1/26/2010 Updated specifications to include 5V operating limits 1.3 5/7/2010 Update branding information 1.4 6/10/2010 Updated tape and reel information 1.5 6/22/2010 Updated Gain Specification lower limit 1.6 12/18/2010 Updated ESD rating Added 802.11n Mask Compliant Power Rating 1.7 1/31/2011 Added 802.11N to ICC table 1.8 2/28/2012 Update Tape and Reel diagram 1.9 5/15/2012 Updated with Skyworks logo and disclaimer statement Copyright © 2012, 2014 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202426E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 12, 2014 10