DATA SHEET SE2597L: 2.4 GHz Power Amplifier with Power Detector Preliminary Information Applications Product Description The SE2597L is a 2.4 GHz power amplifier designed for use in the 2.4 GHz ISM band for wireless LAN applications. The device incorporates a power detector for closed loop monitoring of the output power. DSSS 2.4 GHz WLAN (IEEE802.11b) OFDM 2.4 GHz WLAN (IEEE802.11g) OFDM 2.4 GHz WLAN (IEEE802.11n) Access Points, PCMCIA, PC cards The SE2597L includes a digital enable control for device on/off control. Features Single 3.3 V Supply Operation o 19 dBm, EVM = 3 %, 802.11g, OFDM 54 Mbps o 23 dBm, ACPR < -32 dBc, 802.11b 28 dB Gain Integrated temperature compensated power detector Digital power amplifier enable pin (VEN) Lead Free, Halogen Free and RoHS compliant Small package: 16 pin 3 mm x 3 mm x 0.9 mm QFN, MSL 1 The SE2597L temperature compensated power detector is highly immune to mismatch at its output with less than 1.5 dB of variation with a 2:1 mismatch. Ordering Information Part Number Package Remark SE2597L SE2597L-R SE2597L-EK1 16 Pin QFN 16 Pin QFN Evaluation Kit Samples Tape and Reel Standard Functional Block Diagram Figure 1: Functional Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202434A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 1 DATA SHEET SE2597L: 2.4 GHz Power Amplifier with Power Detector Preliminary Information Pin Out Diagram NU 1 RF IN VCC NU NU NU 16 15 14 13 Paddle = GND 12 VCC3 2 11 RF OUT NU 3 10 NU NU 4 9 DET 5 6 7 8 NU EN NU NU Figure 2: SE2597L Pin-Out Diagram Pin Out Description Pin No. Name Description 1 NU 2 RFin 3,4,5 NU No Connect 6 EN Digital pin used to power up and power down the IC 7,8 NU No Connect 9 DET Analog power detector output 10 NU No Connect 11 RFout Power Amplifier RF output 12 VCC3 Third Stage Collector Voltage 13-15 NU 16 VCC Stages 1, 2 collector supply Paddle GND Exposed die paddle; electrical and thermal ground No Connect Power amplifier RF input; DC block required No Connect Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202434A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 2 DATA SHEET SE2597L: 2.4 GHz Power Amplifier with Power Detector Preliminary Information Absolute Maximum Ratings These are stress ratings only. Exposure to stresses beyond these maximum ratings for a long period of time may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected workstations. Symbol Min. Max. Unit Supply Voltage on pins VCC -0.3 4 V Supply Voltage on pins VCC3 (Note: SE2597L application circuit must be followed for operation above 3.6 V) -0.3 5.5 V VEN Power Amplifier Enable -0.3 3.6 V RFin RF Input Power, RF_OUT terminated into 50Ω match - 10 dBm TSTG Storage Temperature Range -40 150 °C - 500 V Min. Max. Unit VCC RFout ESD HBM Definition JEDEC JESD22-A114 all pins Recommended Operating Conditions Symbol Parameter VCC Supply Voltage 3.0 3.6 V VCC3 Supply Voltage on pins VCC3 3.0 3.6 V Ambient Temperature -40 85 °C TA DC Electrical Characteristics Conditions: VCC = VCC3 = VEN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2597L-EV1 evaluation board, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit ICC-802.11b Supply Current (Sum of VCC0, VCC, VCC3) POUT = 23 dBm, 11 Mbps CCK signal, BT = 0.45, VCC = VCC3 = 3.3 V - 250 - mA ICC-802.11g Supply Current (Sum of VCC,VCC3) POUT = 19 dBm, 54 Mbps OFDM signal, 64 QAM, VCC = VCC3 = 3.3 V - 175 - mA ICQ Supply Current (Sum of VCC,VCC3) No RF - 125 - mA IOFF Supply Current VEN = 0 V, No RF - 2 10 μA VENH Logic High Voltage - 1.3 - VCC V VENL Logic Low Voltage - 0 - 0.5 V IENH Input Current Logic High Voltage - - 300 - μA Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202434A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 3 DATA SHEET SE2597L: 2.4 GHz Power Amplifier with Power Detector Preliminary Information Symbol Parameter Conditions Min. Typ. Max. Unit IENL Input Current Logic Low Voltage - - <1 - μA ZEN Enable pin input impedance Passive Pull Down - 10 - kΩ AC Electrical Characteristics 802.11b/g AC Electrical Characteristics Conditions: VCC = VCC3 = VEN = 3.3 V, f = 2.45 GHz, TA = 25 °C, as measured on Skyworks Solutions’ SE2597L-EV1 evaluation board, unless otherwise noted Symbol fL-U POUT Parameter Frequency Range Conditions Min. Typ. Max. Unit - 2400 - 2500 MHz 54 Mbps OFDM signal, 64 QAM, 3% EVM - 19 - 11 Mbps CCK signal, BT = 0.045, Mask - 23 - 802.11n, HT20, all data rates, Mask - 23 - 802.11n, HT40, all data rates, Mask - 23 - 24.5 26.5 - dBm - -12 -10 dB 26 28 34 dB - 1 - dB - -50 - dBm/MHz - -50 - dBm/MHz - 0.5 - µSec Output Power dBm P1dB Output 1dB compression point S11 Input Return Loss S21 Small Signal Gain PIN = -25 dBm Gain Variation over band PIN = -25 dBm, fIN= 2400 to 2500 MHz Harmonic POUT = 23 dBm, CW ΔS21 No modulation 2f 3f tr , tf Rise and Fall Time - STAB Stability POUT = 23 dBm, 54 Mbps OFDM signal, 64 QAM VSWR = 6:1 All Phases VSWR Tolerance to output load mismatching POUT = 23 dBm, 54 Mbps OFDM signal, 64 QAM VSWR = 10:1 All Phases All non-harmonically related outputs less than -50 dBc/100 kHz No damage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202434A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 4 DATA SHEET SE2597L: 2.4 GHz Power Amplifier with Power Detector Preliminary Information Power Detector Conditions: VCC = VCC3 = VEN = 3.3 V, f = 2.45 GHz, TA = 25 °C, as measured on Skyworks Solutions’ SE2597L-EV1 evaluation board, unless otherwise noted Symbol Parameter Conditions Min. Typ. Max. Unit - 0 - P1dB dBm PDR POUT detect range VDET Detector voltage POUT = 23 dBm - 1.04 - V VDET Detector voltage POUT = 21 dBm - 0.87 - V VDET Detector voltage POUT = NO RF - 0.33 - V PDZOUT Output Impedance - - 2.3 - KΩ PDZLOAD DC load impedance - 10 - - kΩ Pow er Detector Response 2400 2450 2500 1.2 1.1 1 VDET (V) 0.9 0.8 0.7 0.6 0.5 0.4 0.3 3 5 7 9 11 13 15 17 19 21 23 25 Output Pow er (dBm ) Figure 3: SE2597L Power Detector Characteristic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202434A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 5 DATA SHEET SE2597L: 2.4 GHz Power Amplifier with Power Detector Preliminary Information Package Drawing This package is Pb free and RoHS compliant. The product is also rated MSL1. 16 15 14 13 13 14 15 16 1 12 12 1 2 11 11 2 3 10 10 3 4 9 9 4 5 6 7 TOP VIEW 8 8 7 6 5 BOTTOM VIEW Figure 4: SE2597L Package Drawing: Topside Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202434A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 6 DATA SHEET SE2597L: 2.4 GHz Power Amplifier with Power Detector Preliminary Information Recommended Land and Solder Patterns Figure 5: Recommended Land and Solder Patterns Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202434A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 7 DATA SHEET SE2597L: 2.4 GHz Power Amplifier with Power Detector Preliminary Information Package Handling Information Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SE2597L is capable of withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For details on both attachment techniques, precautions, and handling procedures recommended, please refer to: “Quad Flat No-Lead Module Solder Reflow & Rework Information”, Document Number QAD-00045 “Handling, Packing, Shipping and Use of Moisture Sensitive QFN”, Document Number QAD-00044 Caution! Class 1B ESD sensitive device Branding Information Pin 1 Designator Pin 1 Company Name Part Number Lot Code SiGe 2527L 97L Lot Code Figure 6: SE2597L Branding Information Tape and Reel Information Parameter Devices Per Reel Reel Diameter Tape Width Value 3000 13 inches 12 millimeters Figure 7: SE2597L-R Tape and Reel Information Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202434A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 8 DATA SHEET SE2597L: 2.4 GHz Power Amplifier with Power Detector Preliminary Information Document Change History Revision Date Notes 1.0 May 28, 2008 Created 1.1 Aug 25, 2008 Updated application schematic Added recommended land and solder patterns Updated detector characteristics 1.2 Mar 23, 2009 Replace AK1 (application kit) with EK1 (evaluation kit) on page 1 1.3 May 26, 2009 Amended back page 1.4 Oct 14, 2009 Updated Package Outline Drawing 1.5 Feb 3, 2010 Added reference to 0 ESD device handling application note. 1.6 Dec 18, 2010 Updated ESD rating Added OFDM Mask Compliance Extended recommended operating temperature to -40C to +85C 1.7 Apr 03, 2012 Updated with Skyworks logo and disclaimer statement Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202434A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 9