ITAR FREE K-BAND LNB LNB-192-212-XXX 19.2 GHz - 21.2 GHz Description This ITAR-FREE K-Band Low Noise Block (LNB) is designed to meet the extended K-Band Satcom bands and is ideally suited for airborne or SWaP applications where size weight and power are critical. The unit provides 1.5dB Noise Figure over the full 2 GHz bandwidth from 19.2 to 21.2 GHz in 1 GHz electronically switchable bands. Options at time of order include internal or external 10 or 50 MHz ref in addition to a wide input voltage range. The unit also includes a digital attenuator and PLL lock indicator. Other Products Low Noise Block Converters (Ku & X-Band) Block Up Converters (Ku & X-Band) Low Noise Amplifiers (Ku & K-Band) Solid State Power Amplifiers (X, Ku & Ka-Band) Synthesizers (L, C or X-Band) With a total weight of 1.1 lbs and approx size of 5.5” x 3.5” x 0.96” the unit is ideal for todays integrated light weight Ka-Band terminals. Features: Small Size Weight and Power Supports both 10 MHz and 50 MHz Ref Internal Low G-Sensitivity Ref Options Wide Input Voltage Range Operates over 19.2 to 21.2 GHz Electronic Gain Control Internal Built in Lock Alarm Hermetically Sealed ITAR-FREE TELEDYNE MICROWAVE SOLUTIONS Everywhereyoulook TM 1274 Terra Bella Avenue, Mountain View, CA 94043 Tel: 1.800.832.6869 or +1.650.962.6944 Fax: +1.650.962.6845 www.teledynemicrowave.com [email protected] ITAR FREE K-BAND LNB 19.2 GHz - 21.2 GHz Specifications: Parameter Value Input Freq. Range Input Power Maximum Input Power Output Frequency Range Output Power, OP1dB Gain (Switchable) 19.2 to 21.2 GHz 1.5:1 Source VSWR -90 to -25 dBm +10 dBm Switched LO, Low side 1.0 to 2.0GHz 1.5:1 Load VSWR +10 dBm min Selectable Spectrum Inversion 40, 50 or 60 dB Receive None VSWR Input 1.5:1 VSWR Output 1.7:1 Noise Figure Gain Variation Gain Variation with Temperature +23 OC Over any 120MHz IF bandwidth 1.5 dB typ -30 to +60C +/-2.0 dB Linear gain, -5dBm output In-Band Spurious @ <=2.1GHz, >=1.1GHz, IF port -5dBm OUT Out of Band </=1.1GHz, >/=2.1GHz, Spurious @ IF port -5dBm OUT LO Leakage @ RF 18.2GHz / 19.2GHz port 2.0 dBp-p OIP3 LO Frequency Phase Noise Parameter Value Reference Clock Input Level Reference Clock Waveform External Reference Clock Phase Noise Requirement -65 dBc min. -70 dBm max. 10 Hz Offset 100 Hz Offset 18.2 GHz 19.2 GHz -32 dBc/Hz -62 dBc/Hz 1 KHz Offset -75 dBc/Hz 10 KHz Offset -82 dBc/Hz Switched LO, Low side 100 KHz Offset -92 dBc/Hz 1 MHz Offset -105 dBc/Hz 10 MHz Offset 0 +/-3 dBm 50 Ohm load Sinusoidal 10 Hz Offset -120 dBc/Hz 100 Hz Offset -150 dBc/Hz 1 KHz Offset -150 dBc/Hz Input Voltage +12 to +36 VDC Input Current Steady State 600mA max @ 24V Output Connector Input Interface Size SMA(F) or N(F) Waveguide Facing Mounting Surface Excluding connectors Weight Finish +20 dBm -50 dBc min. 25 C Operating Temperature Altitude 1.1 lbs max. Mounting Surface Chem. Film Waveguide Flange surface Chem. Film MICROWAVE SOLUTIONS Everywhereyoulook TM -40 to +73 OC Operational 20,000 feet 30,000 feet Mil-STD-810E Finish Body Relative Humidity 10g, 11ms Half Sine Electroless Nickel 100% Mil-STD-810E 10 or 50 MHz TELEDYNE Painted Non-operational -112 dBc/Hz Reference Clock Input Freq. 5.5" x 3.5" x 1.1" Aluminum Chassis, 6061-T6 Body Shock Shock WR42 1274 Terra Bella Avenue, Mountain View, CA 94043 Tel: 1.800.832.6869 or +1.650.962.6944 Fax: +1.650.962.6845 www.teledynemicrowave.com [email protected] 10g, 11ms Half Sine ITAR FREE K-BAND LNB 19.2 GHz - 21.2 GHz Outline: TABLE 1: J1 15 PIN MICRO D CONNECTOR, M83513/04B11N PIN .05 .95 J1-1 J1-2 J1-3 J1-4 J1-5 J1-6 J1-7 J1-8 J1-9 J1-10 J1-11 J1-12 J1-13 J1-14 J1-15 FUNCTION DC IN 12-32V CHASSIS GND GAIN SET 1 GAIN SET 3 BAND SELECT (L=LOW, H=HIGH) TTL REFERENCE SIGNAL SET 1 REFERENCE SIGNAL SET 2 RESERVED (OPTIONAL 10 MHZ REF IN) DC IN 12-32V CHASSIS GND GAIN SET 2 SYNTHESIZER LOCK OUT: +3.3V RESERVED (FACTORY USE ONLY) RESERVED (FACTORY USE ONLY) RESERVED (FACTORY USE ONLY) 3.50 2X .640 1.430 6X Ø.125 THRU C'BORE Ø.219 X .719 DP 2X .670 J3 RF INPUT WR-42 WAVEGUIDE CAVITY (NO PAINT) 5.51 TDY P/N 2X 4.665 SERIAL NO. LNB-192-212-01O SERNO XXXXXX DATE CODE YYWW 2X 1.180 J1 J2 2.780 .36 2.40 PIN 9 1.08 .26 9 1 PIN 1 .32 15 8 SMA, FEMALE TELEDYNE MICROWAVE SOLUTIONS Everywhereyoulook TM 1274 Terra Bella Avenue, Mountain View, CA 94043 Tel: 1.800.832.6869 or +1.650.962.6944 Fax: +1.650.962.6845 www.teledynemicrowave.com [email protected] 3X MOUNTING SURFACES (NO PAINT) ITAR FREE K-BAND LNB 19.2 GHz - 21.2 GHz Part Numbering System: LNB192212 - _ - _ - _ - _ - _ Parameter Value IF band 1000-2000 MHz 1 950-1950 MHz 9 +12 to +16 V A +16 to +36 V B SMA (f) S N-Type (f) N 60 dB 70 dB 6 Input Voltage IF Connector Max Gain Reference Code 7 External 10MHz via IF Connector A External 10MHz via Separate SMA (f) Connector B External 50MHz via IF Connector C External 50MHz via Separate SMA (f) Connector D -9 Internal Standard 3e g G Sensitivity (Default) E Internal Standard 5e-11g G Sensitivity (High Vib Enviro) F Internal Reference (no ext. ref. required) G Example: LNB-192-212-1-A-S-6-A Has the following options: TELEDYNE • 1000-2000 MHz IF Frequency • +12 V to +16 V Supply Voltage • An SMA(f) IF Connector • A max Gain of 60 dB • Reference Frequency of 10 MHz supplied externally over the IF connector • Note: The internal reference type is “Not Applicable” since the Reference is external. MICROWAVE SOLUTIONS Everywhereyoulook TM 1274 Terra Bella Avenue, Mountain View, CA 94043 Tel: 1.800.832.6869 or +1.650.962.6944 Fax: +1.650.962.6845 www.teledynemicrowave.com [email protected] 03/15