Datasheet - Teledyne Microwave

ITAR-FREE Ka-Band BUC
BUC-290-310-XXX
29 GHz - 31 GHz
This Ka-Band Block Upconverter (BUC) is designed to operate over a single or dual output
frequency range. The unit can be factory configured for a single output frequency range
typically 1 GHz wide or to be switched via a
TTL control between two bands each with a
1 GHz or lower band. The standard switched
unit is configured with the first band operating
over 29-30 GHz and the second band operating over the 30-31 GHz range.
Small modifications to the unit enable custom
bands, both in frequency and bandwidth, to
be incorporated in the unit. The two bands
do not need to be adjacent to each other but
do need to operate in the general Ka-Band
region.
Other products that may be of interest include:
Low Noise Block Converters (Ku & X-Band)
Block Up Converters (Ku & X-Band)
Low Noise Amplifiers (Ku & K-Band)
Solid State Power Amplifiers (X, Ku & Ka-Band)
Synthesizers (L, C or X-Band)
TELEDYNE
MICROWAVE SOLUTIONS
Everywhereyoulook
TM
Various options are available at time of ordering including the following:
•
Variable input supply voltage
•
Internal or external (10MHz or 50MHz)
Reference.
•
Power via Coax or external.
•
Direct LO injection
•
N-Type or SMA input.
1274 Terra Bella Avenue, Mountain View, CA 94043
Tel: 1.800.832.6869 or +1.650.962.6944 Fax: +1.650.962.6845
www.teledynemicrowave.com
[email protected]
ITAR-FREE Ka-Band BUC
29 GHz - 31 GHz
Specifications:
Output Freq. Range
(Switchable) 29 to 31 GHz
Input Power with No Damage
5 dBm
Input Frequency
Switched LO, Non1.0 to 2.0 GHz
Range
Inversion
Output Power, Linear
+10 dBm min
Modulation Spectrum
OQPSK FSymbol = 10Msps
at Linear Power
Spectral Re-growth @1.0 x Fsymbol
Group Delay Variation over full band
2nsec Max
Gain
30dB Min
VSWR Input
2:1
VSWR Output
Gain Variation
Gain Variation with
Temperature
Output Spurious @
Linear Power
LO Frequency
1.7:1
+/-0.75 dB
+/-2.0 dB
Over any 40MHz IF BW
Over full IF BW
+/-2.0 dB
2nd Harmonic
(2xIF)+LO
Fc> +/- 20MHz
-60 dBc
28 GHz
29 GHz
Switched LO, Low side
Phase Noise
(with 10 MHz
external Reference)
100 Hz Offset
-65 dBc/Hz
1 KHz Offset
-75 dBc/Hz
10 KHz Offset
-82 dBc/Hz
100 KHz Offset
-93 dBc/Hz
1 MHz Offset
-122 dBc/Hz
10 MHz Offset
-125 dBc/Hz
TELEDYNE
MICROWAVE SOLUTIONS
Everywhereyoulook
TM
Reference Clock
Input Freq.
Reference Clock
Input Level
Reference Clock
Waveform
External Reference
Clock Phase Noise
Requirement
10 or 50 MHz
25 OC
0 dBm min
50 Ohm load
Sinusoidal
10 Hz Offset
-120 dBc/Hz
100 Hz Offset
-145 dBc/Hz
1 KHz Offset
-165 dBc/Hz
Input Voltage
+8 to +36 VDC
Output Connector
2.9mm-F
IF Input Connector
SMA(F) or N(F)
Direct LO Injection
If Applicable
Connector
DC, Monitor & Control Connector
Ref Input Connector
Size
If Applicable
SMA(F)
9 Pin Micro-D
SMA(F)
4.0” x 4.0” x 1.15”
Weight
Finish
1 lbs max.
Body
Mounting Surface
Operating Temperature
Altitude
-40 to +60 OC
Operational
Non-operational
Relative Humidity
Shock
Electroless
Nickel
Chem. Film
20,000 feet
30,000 feet
Fully Hermetic
Mil-STD-810E
1274 Terra Bella Avenue, Mountain View, CA 94043
Tel: 1.800.832.6869 or +1.650.962.6944 Fax: +1.650.962.6845
www.teledynemicrowave.com
[email protected]
10g, 11ms Half
Sine
ITAR-FREE Ka-Band BUC
29 GHz - 31 GHz
Outline:
TELEDYNE
MICROWAVE SOLUTIONS
Everywhereyoulook
TM
1274 Terra Bella Avenue, Mountain View, CA 94043
Tel: 1.800.832.6869 or +1.650.962.6944 Fax: +1.650.962.6845
www.teledynemicrowave.com
[email protected]
ITAR-FREE Ka-BAND BUC
29 GHz - 31 GHz
Part Numbering System:
BUC290310 - _ - _ - _ - _ - _ Parameter
Value
IF band
1000-2000 MHz
Code
1
950-1950 MHz
9
Input Voltage
+8 to +36 V
A
IF Connector
SMA (f)
S
N-Type (f)
N
Max Gain
30 dB
3
Reference
External 10MHz via IF Connector
A
External 10MHz via Separate SMA(f) Connector
B
External 50MHz via IF Connector
C
External 50MHz via Separate SMA (f) Connector
D
-9
Internal Standard 3e g G Sensitivity (Default)
E
Internal Standard 5e-11g G Sensitivity
(High Vib Enviro)
F
Example: BUC-290-310-1-A-S-3-C
Has the following options:
TELEDYNE
•
1000-2000 MHz IF Frequency
•
+8 V to +36 V Supply Voltage
•
An SMA(f) IF Connector
•
A max Gain of 30 dB
•
Reference Frequency of 50 MHz supplied externally over the IF connector
•
Note: The internal reference type is “Not Applicable” since the Reference is external.
MICROWAVE SOLUTIONS
Everywhereyoulook
TM
1274 Terra Bella Avenue, Mountain View, CA 94043
Tel: 1.800.832.6869 or +1.650.962.6944 Fax: +1.650.962.6845
www.teledynemicrowave.com
[email protected]
03/15