• Low Cost 230VAC LED Power Supply • 0-10V dimmable • Active Power Factor Correction >0.9 • Designed to drive 15W-46W COB LEDs • Terminal Block Input/Output with Cable Clamps • Fully Protected (OLP, SCP, OCP, OTP) • Suitable for Class I and Class II Luminaires Features LED Driver Description AC/DC Converter RCOB-A Dimmable 3 Active PFC Single Output 3Y These ErP-compliant COB LED drivers are available with three preset output currents: 350mA, 700mA and 1050mA. They are designed to drive COB (Chip On Board) high power LEDs with a forward voltage between 6V and 44VDC from a 230VAC supply (198-264VAC). They operate with efficiencies of up to 84%, feature active PFC and are fully protected against short circuit, output overvoltage, open-circuit and over-temperature conditions. The output current is dimmable over a 0%-100% range with a 0-10V external control voltage. The LED drivers are suitable for both independent and built-in installations and for installation inside furniture. wa EAR rranty Selection Guide Part Number Input Output Output Efficiency Max. Rated Voltage Range Voltage Range Current typ. Power (VAC) (VDC) (mA) (%)(W) RCOB-350A 198-2646-440-35080 15 RCOB-700A 198-2646-440-70084 31 RCOB-1050A 198-264 6-440-105083 46 All LED Drivers may not be used without a load. They must be switched on the primary side only. Noncompliance may damage the LED or reduce its lifetime. Specifications (measured at TA= 25°C, nominal input voltage, rated load) BASIC CHARACTERISTICS Parameter Condition Input Voltage Range Output Voltage Range full load absoulute max. Output Voltage full load Min. Typ. Max. 198VAC 230VAC 264VAC 6VDC 44VDC 58VDC Inrush Current at 230VAC 5.5A / 10µs Start-up Time at 230VAC ≤0.5 Second Input Frequency 47Hz 50Hz Efficiency Output Current Accuracy low line to high line, full load ±6% full load, 230VAC 0.9 Power Factor Derating Graph Efficiency RCOB-1050-A 100 95 80 90 Efficiency (%) Output Current (%) 63Hz see Selection Guide EN-61347-1 Compliant EN-61347-2-13 Compliant EN-55015 Compliant EN-61547 Compliant EN-61000-3-2 Compliant EN-61000-3-3 Compliant 60 40 85 80 75 20 0 -20 70 22 -10 0 10 20 30 40 50 60 27 32 37 42 46 Output Voltage (V) Ambient Temperature (°C) Refer to Applications Notes www.recom-international.com REV.: 1/2015 L-1 RCOB-A AC/DC Converter Series Specifications (measured at TA= 25°C, nominal input voltage, rated load) DIMMING Parameter Condition DC Dimming 0-10V Dimming Curve Value 0-100% Output Current (%) 100 80 60 Output = 100% if dimming input not used (open) 40 20 0 1 2 3 4 5 6 7 8 9 10 Dimming Voltage (V) PROTECTION Parameter Condition Value Short Circuit Protection (SCP) 230VAC / 50Hz constant current limit at Inominal and recovers after fault condition is removed Over Load Protection (OLP) 230VAC / 50Hz power limiting, if forward voltage of LED’s is higher than 44VDC Output Over Voltage Protection (OVP) 230VAC / 50Hz 58V max. Output Over Current Protection (OCP) 230VAC / 50Hz constant current source Over Temperature Protection (OTP) automatic recovery after cool down Isolation Voltage Surge Capacity 3kVAC / 1 minute 2kV 4kV L-N L,N-FG Maximum loading of automatic circuit breakers* * @ 115VAC, 1Ohm, 90° phase angle and max. load Power Circuit Breaker Circuit Breaker Current Typ 10A 16A 20A ≥ 7W C 101 128 171 25A 228 ≥ 15W C 47 68 84 105 ≥ 25W C 32 48 57 72 ≥ 35W C 22 35 39 55 ≥ 45W C 16 28 31 43 Power * @ 230VAC, 1Ohm, 90° phase angle and max. load Power ≥ 7W ≥ 15W ≥ 25W ≥ 35W ≥ 45W L-2 Circuit Breaker * @ 277VAC, 1Ohm, 90° phase angle and max. load ≥ 7W Circuit Breaker Current ≥ 15W Typ 10A 16A 20A 25A B 61 100 121 150 C 121 164 221 291 B 35 57 69 85 ≥ 35W C 57 87 109 134 B 24 38 46 58 C 38 62 74 92 B 18 30 35 43 C 29 46 55 69 B 17 28 33 41 C 24 39 47 57 ≥ 25W ≥ 45W REV.: 1/2015 Circuit Breaker Circuit Breaker Current Typ 10A 16A 20A B 61 100 121 25A 150 C 121 164 221 291 B 35 57 69 85 C 57 87 109 134 B 24 38 46 58 C 38 62 74 92 B 18 30 35 43 C 29 46 55 69 B 17 28 33 41 C 24 39 47 57 www.recom-international.com RCOB-A AC/DC Converter Series Specifications (measured at TA= 25°C, nominal input voltage, rated load) ENVIRONMENTAL Parameter Operating Temperature Range max. Case Temperature Range Condition All Types RCOB-350A RCOB-700A RCOB-1050A Storage Temperature Range MTBF -20°C to +50°C, Ambient 80°C max., Ambient 85°C max., Ambient 90°C max., Ambient -30° to +80°C, Ambient Storage Humidity Operating Humidity Value 30% - 95% RH RCOB-1050A RCOB-350 and RCOB-700A at Tc= 70°C; Iout: 350mA at Tc= 70°C; Iout: 700mA, 1050mA 45% to 85% RH 5% to 85% RH, non condensing 45 x 103 hours 50 x 103 hours SAFETY AND CERTIFICATIONS Certificate Type CE General Safety Standard compliant EN-61347-1 CE Safety of AC supplied Control Gear for LED Modules compliant EN-61347-2-13 RoHS compliant RoHS 6/6 Certificate Type (Environmental) Standard / Criterion Electric Lighting, EMC Immunity compliant EN-61547 Electric Lighting, EMC Emissions Limits for Harmonic Emissions EMC Compatability: Flicker and Voltage Variations compliant EN55015, Class B compliant EN-61000-3-2 EN-61000-3-3 IP Rating IP20 DIMENSIONS and PHYSICAL CHARACTERISTICS Parameter Type Case Material Value integrated cable clamps, Plastic Dimensions (LxWxH) RCOB-350A; RCOB-700A RCOB-1050A 106 x 67 x 22mm 121.7 x 78 x 22mm Weight RCOB-350A; RCOB-700A RCOB-1050A 130g 180g Packaging Dimension (LxWxH) Cardboard Box Packaging Quantity 12.5 x 8.2 x 3.8mm 10pcs continued on next page www.recom-international.com REV.: 1/2015 L-3 RCOB-A AC/DC Converter Series Specifications (measured at TA= 25°C, nominal input voltage, rated load) tc 15.5 67.0 RCOB-350A RCOB-700A FC 58.5 31.5 Mechanical Dimensions FC 96.0 tc RCOB-1050A 19.5 FC 68.5 78.0 38.0 22.0 106.0 FC 110.0 22.0 121.7 2 Mounting screws are included tc= Case Temperature Measuring Point Tolerance: ±0.5mm FC: fixing center continued on next page L-4 REV.: 1/2015 www.recom-international.com RCOB-A AC/DC Converter Series Specifications (measured at TA= 25°C, nominal input voltage, rated load) Wiring Diagram L 220N 240V~ wire preparation 7-8mm + + DIM LED FG The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s explicit written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. www.recom-international.com REV.: 1/2015 L-5