● Features ● ● LED DRIVER ● ● ● 35W Class II AC-DC LED Power Supply 500, 700, 1000, 1400mA or 2500mA Output Active Power Factor Correction >0.90 Efficiency up to 83% IP67 Certified 3 in 1 Dimming LIGHTLINE AC/DC-Converter with 5 year Warranty Description The 35W LED drivers of the RACD35-A series come with a 3-in-1 dimming function so that the LED load can be dimmed with analog (1-10V), PWM, or resistor inputs. Due to wide input voltage range of 90 - 305VAC these LED drivers are suitable for worldwide use. They operate with efficiencies of up to 83%, feature active PFC, and are fully protected against short circuit, overvoltage, and over-temperature conditions. They are sealed against damp and wet conditions, and the warranty is 5 years. Selection Guide Part Number Rated Power (W) Output Current (mA) Output Voltage (VDC) Efficiency (typ.) (%) RACD35-500A 28.5 500 48 - 57 82 RACD35-700A 33,6 700 33 - 48 79 RACD35-1000A 36 1000 24 - 36 82 RACD35-1400A 33.6 1400 12 - 24 81 RACD35-2500A 30 2500 9 - 12 80 Specifications (measured at 240VAC and 25°C ambient temperature) Input Voltage Range Input Frequency Range Power Factor 90-305 VAC 47-63Hz Full Load, 277VAC >0.90 Full Load, 230VAC >0.95 Full Load, 110VAC >0.98 AC Input Current 110VAC 0.5A 230VAC 0.3A Inrush Current (Max.) 264VAC Cold Start 60A Leakage Current 230VAC <0.25mA Output Current Accuracy (includes Line Regulation, Load Regulation and set-up tolerance) ±5% Isolation Voltage 3.75kVAC / 1minute Short Circuit Protection Hiccup mode & recovers after fault condition removed Over Voltage Protection 115% - 135% Output Voltage Latch Mode Over Temperature Protection Thermistor 105°C ± 10°C Type Latch Mode Dimming Control: PWM 1<Adj<10V(500Hz - 3kHz) Analogue control by external voltage 1-10VDC Resistance 10K - 100KΩ Set Up Time Full Load, 230VAC 2 sec Storage Humidity 10% - 95% RH Operating Humidity 20% - 95% RH Non-Condensing Weight 384g Dimension (LxBxH) 110 x 73.5 x 33mm Operating Temperature Range Full load -20°C to +50°C (free air convection - 10LFM) Case Temperature 85°C ± 10°C Storage Temperature -40°C to +80°C IP Rating IP67 Isolation Resistance 500VDC 100MΩ MTBF (+25°C) using MIL-HDBK 217F 200 x 10³ hours Certifications: UL Standards Report: E340696 UL8750, (based on) UL1310 Safety Standards Report: P201403013 EN61347-1; EN61347-2-13 continued on next page L-46 REV: 0/2015 35 Watt PFC Single Output RoHS 2011/65/EU 6/6 E340696 UL8750 Certified EN61347 Certified EN55015 Certified EN61547 Certified RACD35-A Derating-Graph (Ambient Temperature) Load 100% 80% 60% 40% AC 100V - 295V Horizontal 20% -20 0 20 50 Ambient Temperature (°C) Note: All LED Drivers may not be used without a load. They must be switched on the primary side only. Noncompliance may damage the LED or reduce its lifetime. Refer to Application Notes www.recom-power.com RACD35-A Series LIGHTLINE AC/DC-Converter Specifications (measured at 240VAC and 25°C ambient temperature) Emission Report: HA130831-SACE FCC EMC Immunity IP67 Report: HA130831-SAFD Report: HA130831-SACE EN55015, Class B IEC61000-3-2 IEC61000-3-3 Part 15, Class B IEC61000-4-2, 3, 4, 5, 6, 8, 11 EN61547 IEC/EN 60598-1 IEC/EN 60529 Report: 14022002 Technical Characteristics Load vs. Input Voltage Load Dimming Curve 100 Ta=25°C 80 Output Current (%) 100% 80% 60% 60 40 20 40% 0 20% 90100 115 130 180 220 240 0 Analoge 1V Resistor 10K PWM 10% 295 Input Voltage (VAC) 60Hz 10V 100K 100% Open connection = 100% Maximum Number of LED drivers per circuit breakers Condition Circuit Breaker 230VAC, 1Ohm 90° phase angle 277VAC, 1Ohm 90° phase angle Typ 10A 16A 20A 25A C 22 35 39 55 B 18 30 35 43 C 29 46 55 69 B 21 34 41 50 C 33 52 63 79 RACD35-A 115VAC, 1Ohm 90° phase angle Circuit Breaker Current Package Style & Pinning 16.7 FC 102.0 16.7 tc 73.5 DC OUT AC IN R1.9 150 ±15 UL 2464 18AWG 4C FC 40.0 SJTW 18AWG 2C AC N (Blue) AC L(Brown) V+ (Red) V- (Black) Dim+ (Blue) Dim- (White) 150 ±15 93.5 110.0 33.0 16 The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s explicit written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. www.recom-power.com REV: 0/2015 L-47