UM50125/50129 - Union Semiconductor

UM50125/50129
Single Line ESD Protection Diode Array
UM50125 SOD523
UM50129 DFN2/FBP2 1.0×0.6
General Description
The UM50125/50129 ESD protection diode is designed to replace multilayer varistors (MLVs) in
portable instrumentation, notebook computers, digital power meter, digital camera and
communication systems. They feature large cross-sectional area junctions for conducting high
transient currents, offer desirable electrical characteristics for board level protection, such as fast
response time, lower operating voltage, lower clamping voltage and no device degradation when
compared to MLVs. The UM50125/50129 ESD protection diode protects sensitive semiconductor
components from damage or upset due to electrostatic discharge (ESD) and other voltage induced
transient events. The UM50125 is available in SOD523 package and the UM50129 is available in
DFN2/FBP2 1.0×0.6 (compatible with SOD923 & SOD882) packages, both with working
voltages of 12 volt. It gives designer the flexibility to protect one unidirectional line in
applications where arrays are not practical. Additionally, it may be “sprinkled” around the board
in applications where board space is at a premium. It may be used to meet the ESD immunity
requirements of IEC 61000-4-2, ±30kV air, ±30kV contact discharge.
Applications
Features







Cell Phone Handsets and Accessories
Notebooks, Desktops and Servers
Portable Instrumentation and
Accessories
Digital Power Meter
Digital Cameras
Communication Systems
Pin Configurations







Transient Protection for Data Lines to IEC
61000-4-2 (ESD): ±30kV (Air), ±30kV
(Contact)
Small Package for Use in Portable Electronics
Suitable Replacement for MLV’s in ESD
Protection Applications
Protect One I/O or Power Line
Low Clamping Voltage
Stand-off Voltage: 12V
Low Leakage Current
Solid-State Silicon-Avalanche Technology
Top View
UM50125
SOD523
UM50129
DFN2/FBP2 1.0×0.6
________________________________________________________________________
http://www.union-ic.com Rev.02 Dec.2014
1/7
UM50125/50129
Ordering Information
Part
Number
Working
Voltage
Packaging Type
Channel
Marking
Code
Shipping Qty
UM50125
12.0V
SOD523
1
ZA
3000pcs/7 Inch
Tape & Reel
UM50129
12.0V
DFN2/FBP2 1.0×0.6
1
EA
5000pcs/7 Inch
Tape & Reel
Absolute Maximum Ratings
Rating
Symbol
Value
Units
Peak Pulse Power (tp = 8/20μs)
PPK
140
Watts
Maximum Peak Pulse Current (t=8/20μs)
IPP
5.9
Amps
TL
TJ
TSTG
260 (10 sec.)
-55 to +125
-55 to +150
°C
°C
°C
Lead Soldering Temperature
Operating Temperature
Storage Temperature
Symbol Definition
Parameter
Maximum Reverse Peak Pulse Current
Clamping Voltage @ Ipp
Working Peak Reverse Voltage
Maximum Reverse Leakage Current @ VRWM
Breakdown Voltage @ It
Test Current
Forward Current
Forward Voltage @ IF
Peak Power Dissipation
Max. Capacitance @ VR = 0V, f = 1MHz
Symbol
IPP
VC
VRWM
IR
VBR
It
IF
VF
PPK
C
________________________________________________________________________
http://www.union-ic.com Rev.02 Dec.2014
2/7
UM50125/50129
Electrical Characteristics
(T=25°C, Device for 12.0V Reverse Stand-off Voltage)
Parameter
Symbol
Conditions
Reverse Stand-Off Voltage
Reverse Breakdown
Voltage
Min
Typ
VRWM
16
Max
Unit
12
V
18
V
VBR
It = 1mA
Reverse Leakage Current
IR
VRWM = 12V, T=25°C
0.5
μA
Clamping Voltage
VC
IPP =5.9A, tp = 8/20μs
23
V
Junction Capacitance
CJ
VR = 0V, f = 1MHz
30
pF
20
Applications Information
Device Connection Options
UM50125/50129 ESD protection diode is designed to protect one data, I/O, or power supply line.
The device is unidirectional and may be used on lines where the signal polarity is above ground.
The cathode dot should be placed towards the line that is to be protected.
Circuit Board Layout Recommendations for Suppression of ESD
Good circuit board layout is critical for the suppression of ESD induced transients. The following
guidelines are recommended:
1. Place the TVS near the input terminals or connectors to restrict transient coupling.
2. Minimize the path length between the TVS and the protected line.
3. Minimize all conductive loops including power and ground loops.
4. The ESD transient return path to ground should be kept as short as possible.
5. Never run critical signals near board edges.
6. Use ground planes whenever possible. For multilayer printed-circuit boards, use ground
vias.
7. Keep parallel signal paths to a minimum.
8. Avoid running protection conductors in parallel with unprotected conductor.
9. Minimize all printed-circuit board conductive loops including power and ground loops.
10. Avoid using shared transient return paths to a common ground point.
________________________________________________________________________
http://www.union-ic.com Rev.02 Dec.2014
3/7
UM50125/50129
Package Information
UM50125 SOD523
Outline Drawing
Symbol
A
A1
b
c
D
E
E1
E2
L
θ
DIMENSIONS
MILLIMETERS
Min
Max
0.510
0.770
0.500
0.700
0.250
0.350
0.080
0.150
0.750
0.850
1.100
1.300
1.500
1.700
0.200REF
0.010
0.070
7°REF
INCHES
Min
Max
0.020
0.031
0.020
0.028
0.010
0.014
0.003
0.006
0.030
0.033
0.043
0.051
0.059
0.067
0.008REF
0.001
0.003
7°REF
Land Pattern
NOTES:
1. Compound dimension: 1.20×0.80;
2. Unit: mm;
3. General tolerance ±0.05mm unless otherwise
specified;
4. The layout is just for reference.
Tape and Reel Orientation
________________________________________________________________________
http://www.union-ic.com Rev.02 Dec.2014
4/7
UM50125/50129
UM50129 DFN2 1.0×0.6
Outline Drawing
Symbol
A
A1
b
D
E
E1
e
R
DIMENSIONS
MILLIMETERS
Min
Max
0.470
0.530
0.000
0.050
0.200
0.300
0.950
1.075
0.550
0.675
0.450
0.550
0.400
0.050
0.150
INCHES
Min
Max
0.019 0.021
0.000 0.002
0.008 0.012
0.037 0.042
0.022 0.027
0.018 0.022
0.016
0.002 0.006
Land Pattern
NOTES:
1. Compound dimension: 1.00×0.60;
2. Unit: mm;
3. General tolerance ±0.025mm unless otherwise
specified;
4. The layout is just for reference.
Tape and Reel Orientation
________________________________________________________________________
http://www.union-ic.com Rev.02 Dec.2014
5/7
UM50125/50129
UM50129 FBP2 1.0×0.6
Outline Drawing
Symbol
A
A1
b
D
D1
E
E1
L
DIMENSIONS
MILLIMETERS
Min
Max
0.550
0.010
0.070
0.275
0.325
0.950
1.050
0.275
0.325
0.400REF
0.550
0.650
0.450REF
INCHES
Min Max
0.021
0.000 0.003
0.011 0.013
0.037 0.041
0.011 0.013
0.016REF
0.022 0.026
0.018REF
Land Pattern
NOTES:
1. Compound dimension: 1.00×0.60;
2. Unit: mm;
3. General tolerance ±0.05mm unless otherwise
specified;
4. The layout is just for reference.
Tape and Reel Orientation
________________________________________________________________________
http://www.union-ic.com Rev.02 Dec.2014
6/7
UM50125/50129
IMPORTANT NOTICE
The information in this document has been carefully reviewed and is believed to be
accurate. Nonetheless, this document is subject to change without notice. Union assumes
no responsibility for any inaccuracies that may be contained in this document, and makes
no commitment to update or to keep current the contained information, or to notify a
person or organization of any update. Union reserves the right to make changes, at any
time, in order to improve reliability, function or design and to attempt to supply the best
product possible.
Union Semiconductor, Inc
Add: Unit 606, No.570 Shengxia Road, Shanghai 201210
Tel: 021-51093966
Fax: 021-51026018
Website: www.union-ic.com
________________________________________________________________________
http://www.union-ic.com Rev.02 Dec.2014
7/7