UM5304EEXF Quad Channel Low Capacitance ESD Protection Array UM5304EEAF SC70-6/SC88/SOT363 UM5304EEBF SC89-6/SOT563/SOT666 UM5304EECF TSOP-6/SOT23-6 General Description UM5304EEXF are surge rated diode arrays designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are connected to data and transmission lines from over-voltage caused by ESD (electrostatic discharge). The unique design incorporates surge rated, low capacitance steering diodes in a single package. During transient conditions, the steering diodes direct the transient to either the positive side of the power supply line or to ground. The low capacitance array configuration allows the user to protect four high-speed data or transmission lines. The low inductance construction minimizes voltage overshoot during high current surges. This device is optimized for ESD protection of portable electronics. They may be used to meet the ESD immunity requirements of IEC 61000-4-2, Level 4 (±15kV air, ±8kV contact discharge). Applications Features USB 2.0 USB OTG Monitors and Flat Panel Displays Digital Visual Interface (DVI) High-Definition Multimedia Interface (HDMI) SIM Ports IEEE 1394 Firewire Ports Pin Configurations Transient Protection for High-Speed Data Lines to IEC 61000-4-2 (ESD) ± 15kV (Air), ± 8kV (Contact) Array of Surge Rated Diodes Protects up to Four I/O Lines & Power Line Low Capacitance (<2pF) for High-Speed Interfaces No Insertion Loss to 2.0GHz Low Leakage Current and Clamping Voltage Low Operating Voltage: 5.0V Top View M: Month Code UM5304EEAF SC70-6/SC88/SOT363 M: Month Code UM5304EEBF SC89-6/SOT563/SOT666 XX: Week Code UM5304EECF TSOP-6/SOT23-6 ___________________________________________________________________________ http://www.union-ic.com Rev.04 Dec.2014 1/8 UM5304EEXF Ordering Information Part Number Working Voltage Packaging Type Channel UM5304EEAF UM5304EEBF UM5304EECF 5.0V SC70-6/ SC88/ SOT363 SC89-6/SOT563/SOT666 TSOP-6/SOT23-6 4 Marking Code UAP UBP UCP Shipping Qty 3000pcs/7 Inch Tape & Reel Absolute Maximum Ratings RATING SYMBOL VALUE UNITS Ppk 150 Watts IPP A kV °C Peak Pulse Power (tp = 8/20µs) Peak Pulse Current (tp = 8/20µs ) ESD per IEC 61000-4-2 (Air) ESD per IEC 61000-4-2 (Contact) Operating Temperature VESD TJ 6 ±15 ±8 -55 to +125 Storage Temperature TSTG -55 to +150 °C Electrical Characteristics PARAMETER Reverse Stand-Off Voltage Reverse Breakdown Voltage Reverse Leakage Current SYMBOL TEST CONDITIONS MIN VRWM VBR IR Clamping Voltage VC Clamping Voltage VC Junction Capacitance Cj It = 1mA Pin 5 to 2 VRWM = 5V, T=25°C Pin 5 to 2 IPP = 1A, 8/20µs Any pin to pin 2 IPP = 6A, 8/20µs Any pin to pin 2 VR = 0V, f = 1MHz Any I/O pin to pin 2 VR = 0V, f = 1MHz Between I/O pins TYP MAX UNIT 5.0 V 6.0 V 2 µA 15 V 25 V 2 pF 1 pF Note 1: I/O pins are pin 1, 3, 4 and 6 ___________________________________________________________________________ http://www.union-ic.com Rev.04 Dec.2014 2/8 UM5304EEXF Typical Operating Characteristics Non-Repetitive Peak Pulse Power vs. Pulse Time Power Derating Curve 110 100 90 % of Rated Power or Ipp Peak Pulse Power – PPK (kW) 10 1 0.1 80 70 60 50 40 30 20 10 0.01 0.1 0 10 1 100 0 1000 25 Pulse Duration – tp (µs) 75 100 125 150 Clamping Voltage vs. Peak Pulse Current Pulse Waveform 110 28 90 80 Clamping Voltage – Vc (V) Waveform Parameters: tr=8μs td=20μs 100 e-t 70 60 50 td=IPP/2 40 30 20 24 Pin 1, 3, 4, 6 to Pin 2 20 16 Pin 5 to Pin 2 Waveform Parameters: tr=8μs td=20μs 12 10 8 0 0 5 10 15 20 25 0 30 1 2 3 4 5 6 Peak Pulse Current – Ipp (A) Time (µs) Forward Voltage vs. Forward Current Junction Capacitance vs. Reverse Voltage 8 3 f=1MHz 2.5 6 Capacitance – Cj (pF) Forward Voltage – VF (V) Percent of Ipp 50 Ambient Temperature - TA(℃) 4 Waveform Parameters: tr=8μs td=20μs 2 0 0 1 2 3 4 Forward Current – IF (A) 5 2 Any I/O Pin to Pin2 1.5 1 0.5 0 6 0 1 2 3 4 5 Reverse Voltage – VR (V) ___________________________________________________________________________ http://www.union-ic.com Rev.04 Dec.2014 3/8 UM5304EEXF Applications Information Device Connection Options for Protection of Four High-Speed Data Lines This device is designed to protect data lines by clamping them to a fixed reference. When the voltage on the protected line exceeds the reference voltage the steering diodes are forward biased, conducting the transient current away from the sensitive circuitry. Data lines are connected at pins 1, 3, 4 and 6. Pin 2 should be connected directly to a ground plane. The path length is kept as short as possible to minimize parasitic inductance. The positive reference is connected at pin 5. The options for connecting the positive reference are as follows: To protect data lines and the power line, connect pin 5 directly to the positive supply rail (VCC). In this configuration the data lines are referenced to the supply voltage. Matte Tin Lead Finish Matte tin has become the industry standard lead-free replacement for SnPb lead finishes. A matte tin finish is composed of 100% tin solder with large grains. Since the solder volume on the leads is small compared to the solder paste volume that is placed on the land pattern of the PCB, the reflow profile will be determined by the requirements of the solder paste. Therefore, these devices are compatible with both lead-free and SnPb assembly techniques. In addition, unlike other lead-free compositions, matte tin does not have any added alloys that can cause degradation of the solder joint. ___________________________________________________________________________ http://www.union-ic.com Rev.04 Dec.2014 4/8 UM5304EEXF Package Information UM5304EEAF SC70-6/SC88/SOT363 Outline Drawing D θ e1 Symbol L e 5 4 1 2 3 L1 E E1 6 20 c b A End View A1 A2 Top View Side View A A1 A2 b c D E E1 e e1 L L1 θ DIMENSIONS MILLIMETERS Min Max 0.900 1.100 0.000 0.100 0.900 1.000 0.150 0.350 0.080 0.150 2.000 2.200 1.150 1.350 2.150 2.450 0.650REF 1.200 1.400 0.525REF 0.260 0.460 0° 8° INCHES Min Max 0.035 0.043 0.000 0.004 0.035 0.039 0.006 0.014 0.003 0.006 0.079 0.087 0.045 0.053 0.085 0.096 0.026REF 0.047 0.055 0.021REF 0.010 0.018 0° 8° Land Pattern 1.94 1.30 0.80 NOTES: 1. Compound dimension: 2.10×1.25; 2. Unit: mm; 3.General tolerance ±0.05mm unless otherwise specified; 4. The layout is just for reference. 0.35 UAP M Tape and Reel Orientation ___________________________________________________________________________ http://www.union-ic.com Rev.04 Dec.2014 5/8 UM5304EEXF UM5304EEBF SC89-6/SOT563/SOT666 Outline Drawing Symbol A A1 b c D E E1 e L θ DIMENSIONS MILLIMETERS INCHES Min Max Min Max 0.525 0.600 0.021 0.024 0.000 0.050 0.000 0.002 0.150 0.300 0.006 0.012 0.090 0.180 0.004 0.007 1.500 1.700 0.059 0.067 1.100 1.300 0.043 0.051 1.500 1.700 0.059 0.067 0.450 0.550 0.018 0.022 0.100 0.300 0.004 0.012 7°REF 7°REF Land Pattern NOTES: 1. Compound dimension: 1.60×1.20; 2. Unit: mm; 3.General tolerance ±0.05mm unless otherwise specified; 4. The layout is just for reference. Tape and Reel Orientation ___________________________________________________________________________ http://www.union-ic.com Rev.04 Dec.2014 6/8 UM5304EEXF UM5304EECF TSOP-6/SOT23-6 Outline Drawing D θ b 5 4 1 2 3 L L1 E E1 6 e c 20 e1 Top View A A2 A1 End View Side View DIMENSIONS MILLIMETERS Symbol Min Max A 1.050 1.250 A1 0.000 0.100 A2 1.050 1.150 b 0.300 0.500 c 0.100 0.200 D 2.820 3.020 E 1.500 1.700 E1 2.650 2.950 e 0.950REF e1 1.800 2.000 L 0.600REF L1 0.300 0.600 θ 0° 8° INCHES Min Max 0.041 0.049 0.000 0.004 0.041 0.045 0.012 0.020 0.004 0.008 0.111 0.119 0.059 0.067 0.104 0.116 0.037REF 0.071 0.079 0.023REF 0.012 0.024 0° 8° Land Pattern 2.4 0.9 0.7 0.95 0.95 NOTES: 1. Compound dimension: 2.92×1.60； 2. Unit: mm; 3. General tolerance ±0.05mm unless otherwise specified; 4. The layout is just for reference. UCP XX Tape and Reel Orientation ___________________________________________________________________________ http://www.union-ic.com Rev.04 Dec.2014 7/8 UM5304EEXF IMPORTANT NOTICE The information in this document has been carefully reviewed and is believed to be accurate. Nonetheless, this document is subject to change without notice. Union assumes no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update or to keep current the contained information, or to notify a person or organization of any update. Union reserves the right to make changes, at any time, in order to improve reliability, function or design and to attempt to supply the best product possible. Union Semiconductor, Inc Add: Unit 606, No.570 Shengxia Road, Shanghai 201210 Tel: 021-51093966 Fax: 021-51026018 Website: www.union-ic.com ___________________________________________________________________________ http://www.union-ic.com Rev.04 Dec.2014 8/8