REI Datasheet - Rochester Electronics

REI Datasheet
MC10198
Monostable Multivibrator
The MC10198 is a retriggerable monostable multivibrator. Two enable inputs permit triggering on any
combination of positive or negative edges. The trigger input is buffered by Schmitt triggers making it
insensitive to input rise and fall times.
The pulse width is controlled by an external capacitor and resistor. The resistor sets a current which
is the linear discharge rate of the capacitor. Also, the pulse width can be controlled by an external
current source or voltage.
Rochester Electronics
Manufactured Components
Rochester branded components are
manufactured using either die/wafers
purchased from the original suppliers
or Rochester wafers recreated from the
original IP. All recreations are done with
the approval of the OCM.
Parts are tested using original factory
test programs or Rochester developed
test solutions to guarantee product
meets or exceeds the OCM data sheet.
Quality Overview
•
•
•
•
ISO-9001
AS9120 certification
Qualified Manufacturers List (QML) MIL-PRF-38535
• Class Q Military
•
Class
V Space Level
Qualified Suppliers List of Distributors (QSLD)
•
Rochester
is a critical supplier to DLA and
meets all industry and DLA standards.
Rochester Electronics, LLC is committed to supplying
products that satisfy customer expectations for
quality and are equal to those originally supplied by
industry manufacturers.
The original manufacturer’s datasheet accompanying this document reflects the performance
and specifications of the Rochester manufactured version of this device. Rochester Electronics
guarantees the performance of its semiconductor products to the original OEM specifications.
‘Typical’ values are for reference purposes only. Certain minimum or maximum ratings may be
based on product characterization, design, simulation, or sample testing.
© 2013 Rochester Electronics, LLC. All Rights Reserved 07112013
To learn more, please visit www.rocelec.com
MC10198
Monostable Multivibrator
The MC10198 is a retriggerable monostable multivibrator. Two
enable inputs permit triggering on any combination of positive or
negative edges as shown in the accompanying table. The trigger input
is buffered by Schmitt triggers making it insensitive to input rise and
fall times.
The pulse width is controlled by an external capacitor and resistor.
The resistor sets a current which is the linear discharge rate of the
capacitor. Also, the pulse width can be controlled by an external
current source or voltage (see applications information).
For high–speed response with minimum delay, a hi–speed input is
also provided. This input bypasses the internal Schmitt triggers and the
output responds within 2 nanoseconds typically.
Output logic and threshold levels are standard MECL 10,000. Test
conditions are per Table 2. Each “Precondition” referred to in Table 2
is per the sequence of Table 1.
• PD = 415 mW typ/pkg (No Load)
• tpd = 4.0 ns typ Trigger Input to Q
•
2.0 ns typ Hi–Speed Input to Q
• Min Timing Pulse Width
PWQmin
10 ns typ1
• Max Timing Pulse Width
PWQmax
>10 ms typ2
• Min Trigger Pulse Width
PWT
2.0 ns typ
• Min Hi–Speed
PWHS
3.0 ns typ
Trigger Pulse Width
• Enable Setup Time
tset
1.0 ns typ
• Enable Hold Time
thold
1.0 ns typ
• 1 CExt = 0 (Pin 4 open), RExt = 0
(Pin 6 to VEE)
• 2 CExt = 10 mF, RExt = 2.7 kW
http://onsemi.com
MARKING
DIAGRAMS
16
CDIP–16
L SUFFIX
CASE 620
MC10198L
AWLYYWW
1
16
PDIP–16
P SUFFIX
CASE 648
MC10198P
AWLYYWW
1
1
PLCC–20
FN SUFFIX
CASE 775
A
WL
YY
WW
10198
AWLYYWW
= Assembly Location
= Wafer Lot
= Year
= Work Week
ORDERING INFORMATION
Device
 Semiconductor Components Industries, LLC, 2002
January, 2002 – Rev. 7
1
Package
Shipping
MC10198L
CDIP–16
25 Units / Rail
MC10198P
PDIP–16
25 Units / Rail
MC10198FN
PLCC–20
46 Units / Rail
Publication Order Number:
MC10198/D
MC10198
LOGIC DIAGRAM
VEE
VCC
6
4
REXT
CEXT
Q
5
E pos
7
EXTERNAL PULSE
WIDTH CONTROL
ENEG
10
DIP
PIN ASSIGNMENT
13
TRIGGER
INPUT
15
HI-SPEED
INPUT
3
VCC1 = PIN 1
VCC2 = PIN 16
VEE = PIN 8
Q
INPUT
L
L
H
H
L
H
L
H
16
VCC2
Q
2
15
HIGH-SPEED
INPUT
Q
3
14
N/C
CEXT
4
13
TRIGGER INPUT
EPOS
5
12
N/C
REXT
6
11
N/C
7
10
ENEG
VEE
8
9
N/C
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion Tables on page 18
of the ON Semiconductor MECL Data Book (DL122/D).
OUTPUT
Triggers on both positive & negative input slopes
Triggers on positive input slope
Triggers on negative input slope
Trigger is disabled
TABLE 1 — PRECONDITION SEQUENCE
1. At t = 0
10 ns
a.)
b.)
c.)
2. At t 10 ns
Apply VIHmax to Pin 5 and 10.
Apply VILmin to Pin 15.
Ground Pin 4.
a.) Open Pin 1.
b.) Apply –3.0 Vdc to Pin 4.
Hold these conditions for
10 ns.
3. Return Pin 4 to Ground and perform test as
indicated in Table 2.
10 ns
0(Gnd)
Pin 4 Voltage (Vdc)
ENeg
1
EXT.PULSE
WIDTH CONTROL
2
TRUTH TABLE
EPos
VCC1
-1.0
-2.0
-3.0
Pin 1
open
-4.0
-5.0
10
0
20
30
t(ns)
TABLE 2 — CONDITIONS FOR TESTING OUTPUT LEVELS
(See Table 1 for Precondition Sequence)
VIH max
VIHA max
VILA max
P1
VIL min
VIL min
P2
Pins 1, 16 = VCC = Ground
Pins 6, 8 = VEE = –5.2 Vdc
Outputs loaded 50 Ω to –2.0 Vdc
http://onsemi.com
2
P3
VIL min
MC10198
Pin Conditions
Test
P.U.T.
Precondition
VOH
2
VOH
3
Precondition
VOL
3
VOL
2
Precondition
VOHA
2
VOHA
3
Precondition
VOHA
2
VOHA
3
Precondition
VOHA
2
VOHA
3
Precondition
VOHA
2
VOHA
3
Precondition
VOHA
2
VOHA
3
5
10
13
Pin Conditions
15
Test
VIL min
P1
VIL min
P1
VILA max
VIHA min
VIL min
P3
P2
P3
VIH max
VIH max
P2
P3
VIH max
VIH max
P1
P1
P.U.T.
Precondition
VOHA
2
VOHA
3
Precondition
VOLA
3
VOLA
2
Precondition
VOLA
2
VOLA
3
Precondition
VOLA
3
VOLA
2
Precondition
VOLA
3
VOLA
2
Precondition
VOLA
3
VOLA
2
Precondition
VOLA
3
VOLA
2
http://onsemi.com
3
5
10
13
VIHA min
VILA max
P1
P1
15
VILA max
VIHA min
VIL min
VIL min
P2
P3
VIH max
VIH max
P2
P3
VIHA min
VILA max
VIH max
VIH max
P1
P1
VIH max
VIH max
VIHA min
VILA max
P1
P1
MC10198
ELECTRICAL CHARACTERISTICS
Test Limits
Characteristic
Symbol
Pin
Under
Test
Power Supply Drain Current
IE
8
110
IinH
5, 10
13
15
415
350
560
Input Current
–30°C
Min
+25°C
Max
Min
+85°C
Typ
Max
Max
Unit
80
100
110
mAdc
260
220
350
260
220
350
µAdc
0.5
Min
µAdc
IinL
5
0.5
Output Voltage
Logic 1
VOH
2
3
–1.060
–1.060
–0.890
–0.890
–0.960
–0.960
–0.810
–0.810
–0.890
–0.890
0.3
–0.700
–0.700
Vdc
Output Voltage
Logic 0
VOL
2
3
–1.890
–1.890
–1.675
–1.675
–1.850
–1.850
–1.650
–1.650
–1.825
–1.825
–1.615
–1.615
Vdc
Threshold Voltage
Logic 1
VOHA
2
3
–1.080
–1.080
Threshold Voltage
Logic 0
VOLA
2
3
tT+Q+
tT–Q+
3
3
2.5
2.5
6.5
6.5
2.5
2.5
High Speed Trigger Input
tHS+Q+
3
1.5
3.2
1.5
Minimum Timing Pulse
Width
PWQmin
3
10.0
ns
Maximum Timing Pulse
Width
PWQmax
3
>10
ms
Min Trigger Pulse Width
PWT
3
2.0
ns
PWHS
3
–0.980
–0.980
–0.910
–0.910
–1.655
–1.655
–1.630
–1.630
Vdc
–1.595
–1.595
Vdc
Switching Times (50Ω Load)
Trigger Input
Min Hi–Spd Trig Pulse Width
4.0
4.0
5.5
5.5
2.5
2.5
6.5
6.5
ns
2.0
2.8
1.5
3.2
ns
3.0
ns
Rise Time
(20 to 80%)
3
1.5
4.0
1.5
3.5
1.5
4.0
ns
Fall Time
(20 to 80%)
3
1.5
4.0
1.5
3.5
1.5
4.0
ns
Enable Setup Time
tsetup (E)
3
1.0
ns
Enable Hold Time
thold (E)
3
1.0
ns
1. The monostable is in the timing mode at the time of this test.
2. CEXT = 0 (Pin 4 Open); REXT = 0 (Pin 6 tied to VEE).
3. CEXT = 10µF (Pin); REXT = 2.7k (Pin 6).
VIHmax
4.
P1
VILmin
http://onsemi.com
4
MC10198
ELECTRICAL CHARACTERISTICS (continued)
TEST VOLTAGE VALUES (Volts)
Characteristic
Power Supply Drain Current
Input Current
Output Voltage
Logic 1
Output Voltage
Logic 0
Threshold Voltage
Logic 1
Threshold Voltage
Logic 0
Switching Times
@ Test Temperature
VIHmax
VILmin
VIHAmin
VILAmax
VEE
–30°C
–0.890
–1.890
–1.205
–1.500
–5.2
+25°C
–0.810
–1.850
–1.105
–1.475
–5.2
+85°C
–0.700
–1.825
–1.035
–1.440
–5.2
Symbol
Pin
Under
Test
IE
8
IinH
5, 10
13
15
IinL
5
VOH
2
3
VOL
VOHA
VOLA
VIHmax
VEE
(VCC)
Gnd
6, 8
1, 4, 16
6, 8
6, 8
6, 8
1, 4, 16
1, 4, 16
1, 4, 16
5
6, 8
1, 4, 16
13
6, 8
6, 8
1, 4, 16
1, 4, 16
6, 8
6, 8
1, 4, 16
1, 4, 16
6, 8
6, 8
1, 16, 4
1, 16, 4
15
6, 8
6, 8
1, 16, 4
1, 16, 4
VILmin
VIHAmin
VILAmax
5,10
13
15
13 (4.)
2
3
13 (4.)
13
2
3
15
15
2
3
15
(50Ω Load)
Trigger Input
TEST VOLTAGE APPLIED TO PINS LISTED BELOW
+1.11V
Pulse In
Pulse Out
–3.2 V
+2.0 V
10
5
13
13
3
3
6, 8
6, 8
1, 16, 4
1, 16, 4
tT+Q+
tT–Q+
3
3
High Speed Trigger Input
tHS+Q+
3
3
6, 8
1, 16, 4
Minimum Timing Pulse Width
PWQmin
3
Note 2.
6, 8
1, 16, 4
Maximum Timing Pulse Width
PWQmax
3
Note 3.
6, 8
1, 16, 4
PWT
3
13
3
6, 8
1, 16, 4
PWHS
3
15
3
6, 8
1, 16, 4
Minimum Trigger Pulse Width
Minimum Hi–Spd Trigger Pulse
Width
15
Rise Time
(20 to 80%)
3
6, 8
1, 16, 4
Fall Time
(20 to 80%)
3
6, 8
1, 16, 4
Enable Setup Time
tsetup (E)
3
5
3
6, 8
1, 16, 4
Enable Hold Time
thold (E)
3
5
3
6, 8
1, 16, 4
1. The monostable is in the timing mode at the time of this test.
2. CEXT = 0 (Pin 4 Open); REXT = 0 (Pin 6 tied to VEE).
3. CEXT = 10µF (Pin); REXT = 2.7k (Pin 6).
VIHmax
4.
P1
VILmin
Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been
established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained.
Outputs are terminated through a 50–ohm resistor to –2.0 volts. Test procedures are shown for only one gate. The other gates are tested in the
same manner.
http://onsemi.com
5
MC10198
SWITCHING TIME TEST CIRCUIT AND WAVEFORMS @ 25°C
VCC1 = VCC2 = +2.0 Vdc
Vin
25 µF
Vout
0.1 µF
Coax
Coax
5
Input
EPos
7
TPin
External Pulse
Width Control
10
Pulse Generator
+1.11 V
TPout
Trigger Input
0.1 µF
15
Hi-Speed Input
Input Pulse
6
RExt
4
Q
2
CExt
50–ohm termination to ground located
in each scope channel input.
0.1 µF
All input and output cables to the scope
are equal lengths of 50–ohm coaxial
cable. Wire length should be < 1/4 inch
from TPin to input pin and TPout to
output pin.
Unused outputs are tied to a
50–ohm resistor to ground.
VEE = -3.2 Vdc
50%
EPos
tsetup (E)
Trigger Input
Q
3
ENeg
13
t+ = t- = 2.0 ± 0.2 ns
(20 to 80%)
Q
50%
tT+Q+
PWT
tHold(E)
tT-Q+
50%
50%
PWQ
High-Speed
Trigger Input
tHS+Q+
PWHS
Q
PWQ
http://onsemi.com
6
MC10198
APPLICATIONS INFORMATION
Circuit Operation:
1. PULSE WIDTH TIMING — The pulse width is determined by the external resistor and capacitor. The MC10198
also has an internal resistor (nominally 284 ohms) that can be used in series with RExt. Pin 7, the external pulse
width control, is a constant voltage node (–3.60 V nominally). A resistance connected in series from this node to
VEE sets a constant timing current IT. This current determines the discharge rate of the capacitor:
Then:
∆T = pulse width
∆V = 1.9 V change in capacitor voltage
∆V
∆T
IT = CExt
If RExt + RInt are in series to VEE:
IT = [(–3.60 V) – (–5.2 V)] ÷ [RExt + 284 Ω]
IT = 1.6 V/(RExt + 284)
1.9 V
The timing equation becomes: ∆T = CExt I
FIGURE 2 – TIMING PULSE WIDTH versus CExt and RExt
100
PULSE WIDTH (s)
µ
where
T
10
10 kΩ
3 kΩ
1
500 Ω
100
∆T = [(CExt)(1.9 V)] ÷ [1.6 V/(RExt + 284)]
∆T = CExt (RExt + 284) 1.19
RExt = 0
10
10 pF
where ∆T = Sec
RExt = Ohms
CExt = Farads
Figure 2 shows typical curves for pulse width versus CExt
and RExt (total resistance includes RInt). Any low leakage capacitor can be used and RExt can vary from 0 to 16 k–ohms.
100 pF
NOTE: TOTAL RESISTANCE
= RExt + RInt
1000 pF
0.01 µF
CExt - TIMING CAPACITANCE
0.1 µF
2. TRIGGERING —The Epos and ENeg inputs control the trigger input. The MC10198 can be programmed to trigger
on the positive edge, negative edge, or both. Also, the trigger input can be totally disabled. The truth table is
shown on the first page of the data sheet.
The device is totally retriggerable. However, as duty cycle
approaches 100%, pulse width jitter can occur due to the recovery time of the circuit. Recovery time is basically dependent on capacitance CExt. Figure 3 shows typical recovery
time versus capacitance at IT = 5 mA.
FIGURE 3 — RECOVERY TIME versus CExt @ IT = 5 mA
FIGURE 1 —
4
7
RInt
284 Ω
-3.60 V External
Pulse Width Control
RECOVERY TIME
MC10198
10 µs
CExt
6
1 µs
100 ns
10 ns
RExt
1 ns
10 pF
VEE = -5.2 V
http://onsemi.com
7
100 pF
1000 pF
0.01 µF
CExt - TIMING CAPACITANCE
0.1 µF
MC10198
3. HI–SPEED INPUT — This input is used for stretching very narrow pulses with minimum delay between the output
pulse and the trigger pulse. The trigger input should be disabled when using the high–speed input. The MC10198
triggers on the rising edge, using this input, and input pulse width should narrow, typically less than 10 nanoseconds.
USAGE RULES:
1. Capacitor lead lengths should be kept very short to minimize ringing due to fast recovery rise times.
2. The E inputs should not be tied to ground to establish a high logic level. A resistor divider or diode can be used to
establish a –0.7 to –0.9 voltage level.
3. For optimum temperature stability; 0.5 mA is the best timing current IT. The device is designed to have a constant
voltage at the EXTERNAL PULSE WIDTH CONTROL over temperature at this current value.
4. Pulse Width modulation can be attained with the EXTERNAL PULSE WIDTH CONTROL. The timing current can
be altered to vary the pulse width. Two schemes are:
a. The internal resistor is not used. A dependent curb. A control voltage can also be used to vary the pulse
rent source is used to set the timing current as
width using an additional resistor (Figure 6). The
shown in Figure 4. A graph of pulse width versus
current (IT + IC) is set by the voltage drop across
timing current (CExt = 13 pF) is shown in Figure
RInt + RExt. The control current IC modifies IT and
5.
alters the pulse width. Current IC should never
force IT to zero. RC typically 1 kΩ.
FIGURE 4 —
1000
CExt
PULSE WIDTH (ns)
4
MC10198
7
FIGURE 5 — PULSE WIDTH versus IT @ CExt = 13 pF
100
I
10
0.01 mA
0.1 mA
1 mA
IT - TIMING CURRENT
FIGURE 6 —
4
CExt
IT
7
-3.6
V
284
IC
RC
6
IT + IC
RExt
-5.2 V
http://onsemi.com
8
Control
Voltage
10 mA
MC10198
5. The MC10198 can be made non–retriggerable. The
Q output is fed back to disable the trigger input during the triggered state (Logic Diagram). Figure 7
shows a positive triggered configuration; a similar
configuration can be made for negative triggering.
FIGURE 7 —
VEE
VCC
RExt
6
CExt
4
Q
E Pos
External Pulse
Width Control
-0.9 V
ENeg
Trigger
Input
Hi-Speed
Input
Q
http://onsemi.com
9
MC10198
PACKAGE DIMENSIONS
PLCC–20
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 775–02
ISSUE C
0.007 (0.180)
B
Y BRK
–N–
M
T L-M
0.007 (0.180)
U
M
N
S
T L-M
S
G1
0.010 (0.250)
S
N
S
D
–L–
–M–
Z
W
20
D
1
X
V
S
T L-M
S
N
S
VIEW D–D
A
0.007 (0.180)
M
T L-M
S
N
S
R
0.007 (0.180)
M
T L-M
S
N
S
Z
0.007 (0.180)
H
M
T L-M
S
N
S
K1
K
C
E
F
0.004 (0.100)
G
J
–T–
VIEW S
G1
0.010 (0.250) S T L-M
S
N
S
0.007 (0.180)
M
T L-M
S
VIEW S
SEATING
PLANE
NOTES:
1. DATUMS -L-, -M-, AND -N- DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS PLASTIC
BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM -T-, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE MOLD
FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN THE
PACKAGE BOTTOM BY UP TO 0.012 (0.300).
DIMENSIONS R AND U ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,
GATE BURRS AND INTERLEAD FLASH, BUT
INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF THE PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037 (0.940).
THE DAMBAR INTRUSION(S) SHALL NOT CAUSE
THE H DIMENSION TO BE SMALLER THAN 0.025
(0.635).
http://onsemi.com
10
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
INCHES
MIN
MAX
0.385
0.395
0.385
0.395
0.165
0.180
0.090
0.110
0.013
0.019
0.050 BSC
0.026
0.032
0.020
--0.025
--0.350
0.356
0.350
0.356
0.042
0.048
0.042
0.048
0.042
0.056
--0.020
2
10 0.310
0.330
0.040
---
MILLIMETERS
MIN
MAX
9.78
10.03
9.78
10.03
4.20
4.57
2.29
2.79
0.33
0.48
1.27 BSC
0.66
0.81
0.51
--0.64
--8.89
9.04
8.89
9.04
1.07
1.21
1.07
1.21
1.07
1.42
--0.50
2
10 7.88
8.38
1.02
---
N
S
MC10198
PACKAGE DIMENSIONS
–A–
16
9
1
8
–B–
CDIP–16
L SUFFIX
CERAMIC DIP PACKAGE
CASE 620–10
ISSUE T
C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIMENSION F MAY NARROW TO 0.76 (0.030)
WHERE THE LEAD ENTERS THE CERAMIC
BODY.
L
DIM
A
B
C
D
E
F
G
H
K
L
M
N
–T–
K
N
SEATING
PLANE
M
E
F
J
G
D
16 PL
0.25 (0.010)
16 PL
0.25 (0.010)
M
T A
T B
M
S
PDIP–16
P SUFFIX
PLASTIC DIP PACKAGE
CASE 648–08
ISSUE R
–A–
16
9
1
8
B
F
C
L
S
–T–
SEATING
PLANE
K
H
G
D
M
J
16 PL
0.25 (0.010)
M
S
T A
M
http://onsemi.com
11
INCHES
MIN
MAX
0.750
0.785
0.240
0.295
--0.200
0.015
0.020
0.050 BSC
0.055
0.065
0.100 BSC
0.008
0.015
0.125
0.170
0.300 BSC
0
15 0.020
0.040
MILLIMETERS
MIN
MAX
19.05
19.93
6.10
7.49
--5.08
0.39
0.50
1.27 BSC
1.40
1.65
2.54 BSC
0.21
0.38
3.18
4.31
7.62 BSC
0
15 0.51
1.01
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
DIM
A
B
C
D
F
G
H
J
K
L
M
S
INCHES
MIN
MAX
0.740
0.770
0.250
0.270
0.145
0.175
0.015
0.021
0.040
0.70
0.100 BSC
0.050 BSC
0.008
0.015
0.110
0.130
0.295
0.305
0
10 0.020
0.040
MILLIMETERS
MIN
MAX
18.80
19.55
6.35
6.85
3.69
4.44
0.39
0.53
1.02
1.77
2.54 BSC
1.27 BSC
0.21
0.38
2.80
3.30
7.50
7.74
0
10 0.51
1.01
MC10198
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
http://onsemi.com
12
MC10198/D