2SD2674 Transistors General purpose amplification (12V, 1.5A) 2SD2674 zExternal dimensions (Unit : mm) zApplication Low frequency amplifier TSMT3 1.0MAX zFeatures 1) A collector current is large. 2) Collector saturation voltage is low. 2.9 0.85 0.4 0.7 1.6 2.8 (3) 0.3~0.6 < 200mV VCE(sat) = at IC = 500mA / I B = 25mA 0~0.1 (2) (1) 0.95 0.95 0.16 1.9 (1) Base (2) Emitter Each lead has same dimensions (3) Collector zPackaging specifications zAbsolute maximum ratings (Ta=25°C) Parameter Symbol Limits Unit Collector-base voltage VCBO 15 V Collector-emitter voltage VCEO 12 V VEBO 6 V IC 1.5 A ICP 3 Power dissipation PC 500 1 ∗2 mW Junction temperature Tj 150 °C Tstg −55 to +150 °C Emitter-base voltage Collector current Range of storage temperature Package Type Taping TL Code Basic ordering unit (pieces) 3000 2SD2674 A ∗1 W ∗1 Single pulse, PW=1ms ∗2 Mounted on a 25×25× t 0.8mm Ceramic substrate zElectrical characteristics (Ta=25°C) Parameter Symbol Min. Typ. Max. Unit − Collector-base breakdown voltage BVCBO 15 Collector-emitter breakdown voltage BVCEO 12 − Emitter-base breakdown voltage BVEBO 6 − − Conditions V IC=10µA − V IC=1mA − V IE=10µA VCB=15V Collector cutoff current ICBO − − 100 nA Emitter cutoff current IEBO − − 100 nA VEB=6V VCE(sat) − 85 200 mV IC/IB=500mA/25mA DC current gain hFE 270 − 680 − VCE/IC=2V/200mA Transition frequency fT − 400 − Cob − 12 − Collector-emitter saturation voltage Collector output capacitance ∗ MHz VCE=2V, IE=−200mA, f=100MHz ∗ pF VCB=10V, IE=0A, f=1MHz ∗ Pulsed Rev.B 1/2 2SD2674 Transistors BASE SATURATION VOLTAGE : VBE (sat) (V) COLLECTOR SATURATION VOLTAGE : VCE (sat) (V) 1000 Ta=25°C Ta=−40°C 100 VCE=2V Pulsed 10 0.001 0.01 0.1 1 10 COLLECTOR CURRENT : IC (A) TRANSITION FREQUENCY : fT (MHz) COLLECTOR CURRENT : IC (A) 1 Ta=100°C Ta=25°C Ta=−40°C 0.01 0.001 0 1.0 0.5 1.5 Ta=25°C Ta=−40°C VCE(sat) 0.01 0.001 0.001 0.01 0.1 1 10 COLLECTOR CURRENT : IC (A) 1 Ta=25°C VCE=2V 0.1 IC/IB=50/1 0.01 IC/IB=20/1 IC/IB=10/1 0.001 0.001 0.01 0.1 1 10 COLLECTOR CURRENT : IC (A) Fig.3 Collector-emitter saturation voltage vs. collector current 1000 Ta=25°C VCE=2V f=100MHz 100 10 −0.001 VCE=2V Ta=25°C Pulsed −0.01 −0.1 −1 Fig.5 Gain bandwidth product vs. emitter current Fig.4 Grounded emitter propagation characteristics EMITTER INPUT CAPACITANCE : Cib (pF) COLLECTOR OUTPUT CAPACITANCE : Cob (pF) Ta=100°C 0.1 EMITTER CURRENT : IE (A) BASE TO EMITTER VOLTAGE : VBE (V) 100 VBE(sat) 1000 VCE=2V Pulsed 0.1 1 Ta=−40°C Ta=25°C Ta=100°C =20/1 IC/IB=20 Pulsed Fig.2 Collector-emitter saturation voltage base-emitter saturation voltage vs. collector current Fig.1 DC current gain vs. collector current 10 10 −10 SWITCHING TIME : (ns) DC CURRENT GAIN : hFE Ta=100°C COLLECTOR SATURATION VOLTAGE : VCE(sat) (V) zElectrical characteristic curves tstg 100 10 tdon tf tr 1 0.01 0.1 1 10 COLLECTOR CURRENT : IC (A) Fig.6 Switching time IE=0A f=1MHz Ta=25°C Cib Cob 10 1 0.1 1 10 100 EMITTER TO BASE VOLTAGE : VEB (V) COLLECTOR TO BASE VOLTAGE : VCB (V) Fig.7 Collector output capacitance vs. collector-base voltage Emitter input capacitance vs. emitter-base voltage Rev.B 2/2 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1