RT5796C 1.5A, 1MHz, 5.5V CMCOT Synchronous Step-Down Converter Features General Description The RT5796C is a high efficiency synchronous step-down DC/DC converter. Its input voltage range is from 2.5V to 5.5V and provides an adjustable regulated output voltage from 0.6V to 3.4V while delivering up to 1.5A of output current. The internal synchronous low on-resistance power switches increase efficiency and eliminate the need for an external Schottky diode. The Current Mode Constant-On-time (CMCOT) operation with internal Efficiency Up to 95% RDSON 160m HS / 110m LS VIN Range 2.5V to 5.5V VREF 0.6V with 2% Accuracy CMCOT ™ Control Loop Design for Best Transient Response, Robust Loop Stability with Low-ESR (MLCC) COUT Fixed Soft-Start 1.2ms; PGOOD Function in TSOT-23-6 Cycle-by-Cycle Over Current Protection compensation allows the transient response to be optimized over a wide range of loads and output capacitors. The RT5796C is available in the TSOT-23-5 and TSOT-23-6 packages. Ordering Information Applications RT5796C Package Type J5 : TSOT-23-5 J6 : TSOT-23-6 Input Under Voltage Lockout Output Under Voltage Protection (UVP Hiccup) Thermal Shutdown Protection Power Saving at Light Load STB, Cable Modem, & xDSL Platforms LCD TV Power Supply & Metering Platforms General Purpose Point of Load (POL) Marking Information Lead Plating System G : Green (Halogen Free and Pb Free) RT5796CHGJ5 UVP Trim Option H: Hiccup 0R=DNN 0R= : Product Code DNN : Date Code PWM/PSM Mode C : PSM/PWM RT5796CHGJ6 Note : 17=DNN Richtek products are : 17= : Product Code DNN : Date Code RoHS compliant and compatible with the current requirements of IPC/JEDEC J-STD-020. Suitable for use in SnPb or Pb-free soldering processes. Simplified Application Circuit RT5796C LX VIN VIN CIN L VOUT R1 EN COUT FB PG* GND R2 *For TSOT-23-6 Package Only Copyright © 2015 Richtek Technology Corporation. All rights reserved. DS5796C-00 February 2015 is a registered trademark of Richtek Technology Corporation. www.richtek.com 1 RT5796C Pin Configurations (TOP VIEW) FB VIN FB 5 4 6 2 3 PG VIN 5 4 2 3 EN GND LX EN GND LX TSOT-23-5 TSOT-23-6 Functional Pin Description Pin No. Pin Name Pin Function TSOT-23-5 TSOT-23-6 1 1 EN Enable Control Input. 2 2 GND Power Ground and Quiet Ground for Controller Circuits. 3 3 LX Switch Node. 4 4 VIN Supply Voltage Input. The RT5796C operates from a 2.5V to 5.5V unregulated input. C1 is needed to prevent large voltage spikes from appearing at the input. Quiet ground for controller circuits. 5 6 FB Feedback Voltage Input. An external resistor divider from the output to GND, tapped to the FB pin, sets the output voltage. -- 5 PG Power Good Indicator. The output of this pin is an open-drain with external pull-up resistor to IN. PG is pulled up to IN when the FB voltage is within 90%, otherwise it is LOW. Copyright © 2015 Richtek Technology Corporation. All rights reserved. www.richtek.com 2 is a registered trademark of Richtek Technology Corporation. DS5796C-00 February 2015 RT5796C Function Block Diagram For TSOT-23-5 Package EN VIN UVLO Shut Down Control OTP FB - VREF Error Amplifier Ton Comparator + - + RC CCOMP Logic Control LX VIN Driver Current Limit Detector LX GND Current Sense LX Ton LX For TSOT-23-6 Package EN VIN UVLO Shut Down Control OTP - FB VREF Error Amplifier Comparator + + RC CCOMP - Logic Control VIN Driver Current Limit Detector LX GND + Current Sense - LX PG Operation The RT5796C is a synchronous low voltage step-down Low side MOSFET peak current is measured by converter that can support the input voltage range from 2.5V to 5.5V and the output current can be up to 1.5A. internal RSENSE. The error amplifier EA adjusts COMP voltage by comparing the feedback signal (VFB) from The RT5796C uses a constant on-time, current mode architecture. In normal operation, the high side the output voltage with the internal 0.6V reference. When the load current increases, it causes a drop in the P-MOSFET is turned on when the switch controller is set by the comparator and is turned off when the Ton comparator resets the switch controller. feedback voltage relative to the reference, then the COMP voltage rises to allow higher inductor current to match the load current. Copyright © 2015 Richtek Technology Corporation. All rights reserved. DS5796C-00 February 2015 is a registered trademark of Richtek Technology Corporation. www.richtek.com 3 RT5796C UV Comparator If the feedback voltage (VFB) is lower than threshold voltage 0.2V, the UV comparator's output will go high and the switch controller will turn off the high side MOSFET. The output under voltage protection is designed to operate in Hiccup mode. PGOOD Comparator When the feedback voltage (VFB) is higher than threshold voltage 0.54V, the PGOOD open drain output will be high impedance. The internal PG MOSFET is typical 10. The PGOOD signal delay time from EN is about 2ms. Enable Comparator A logic-high enables the converter; a logic-low forces the IC into shutdown mode. Over Current Protection (OCP) The RT5796C provides over current protection by detecting low side MOSFET valley inductor current. If the sensed valley inductor current is over the current limit threshold (1.8A typ.), the OCP will be triggered. When OCP is tripped, the RT5796C will keep the over current threshold level until the over current condition is removed. Thermal Shutdown (OTP) The device implements an internal thermal shutdown function when the junction temperature exceeds 150°C. The thermal shutdown forces the device to stop switching when the junction temperature exceeds the thermal shutdown threshold. Once the die temperature decreases below the hysteresis of 20°C, the device reinstates the power up sequence. Soft-Start (SS) An internal current source charges an internal capacitor to build the soft-start ramp voltage. The VFB voltage will track the internal ramp voltage during soft-start interval. The typical soft-start time is 1.2ms. Copyright © 2015 Richtek Technology Corporation. All rights reserved. www.richtek.com 4 is a registered trademark of Richtek Technology Corporation. DS5796C-00 February 2015 RT5796C Absolute Maximum Ratings (Note 1) Supply Input Voltage -------------------------------------------------------------------------------------------0.3V to 6.5V LX Pin Switch Voltage----------------------------------------------------------------------------------------- 0.3V to (VIN + 0.3V) <20ns -------------------------------------------------------------------------------------------------------------- 4.5V to 7.5V Power Dissipation, PD @ TA = 25C TSOT-23-5 --------------------------------------------------------------------------------------------------------0.43W TSOT-23-6 --------------------------------------------------------------------------------------------------------0.5W Package Thermal Resistance (Note 2) TSOT-23-5, JA --------------------------------------------------------------------------------------------------230.6C/W TSOT-23-6, JA --------------------------------------------------------------------------------------------------197.4C/W Lead Temperature (Soldering, 10 sec.) --------------------------------------------------------------------260C Junction Temperature ------------------------------------------------------------------------------------------40C to 150C Storage Temperature Range ---------------------------------------------------------------------------------65C to 150C ESD Susceptibility (Note 3) HBM (Human Body Model) -----------------------------------------------------------------------------------2kV Recommended Operating Conditions (Note 4) Supply Input Voltage -------------------------------------------------------------------------------------------2.5V to 5.5V Ambient Temperature Range---------------------------------------------------------------------------------40C to 85C Junction Temperature Range --------------------------------------------------------------------------------40C to 125C Electrical Characteristics (VIN = 3.6V, TA = 25C, unless otherwise specified) Parameter Symbol Min Typ Max Unit 2.5 -- 5.5 V 0.588 0.6 0.612 V VFB = 3.3V -- -- 1 A Active , VFB = 0.63V, Not Switching -- 22 -- Shutdown -- -- 1 Switching Leakage Current -- -- 1 A Switching Frequency -- 1 -- MHz Input Voltage VIN Feedback Reference Voltage VREF Feedback Leakage Current IFB DC Bias Current Test Conditions A Switch On Resistance, High RPMOS ISW = 0.3A -- 160 -- m Switch On Resistance, Low RNMOS ISW = 0.3A -- 110 -- m Valley Current Limit ILIM 1.53 1.8 2.4 A VDD Rising -- 2.25 2.5 V Under-Voltage Lockout Threshold VUVLO VDD Falling -- 2 -- V -- 150 -- °C Over-Temperature Threshold Copyright © 2015 Richtek Technology Corporation. All rights reserved. DS5796C-00 February 2015 is a registered trademark of Richtek Technology Corporation. www.richtek.com 5 RT5796C Parameter Min Typ Max 1.5 -- -- -- -- 0.4 FB Rising -- 90 -- FB Falling -- 85 -- -- -- 100 -- 1.2 -- ms Minimum Off Time -- 120 -- ns Output Discharge Switch On Resistance -- 1.8 -- k Enable Input Voltage Symbol Test Conditions Logic-High VIH Logic-Low VIL PG Pin Threshold (relative to VOUT) PG Open-Drain Impedance (PG = low) Soft-Start Time TSS Unit V % Note 1. Stresses beyond those listed “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions may affect device reliability. Note 2. JA is measured at TA = 25C on a high effective thermal conductivity four-layer test board per JEDEC 51-7. Note 3. Devices are ESD sensitive. Handling precaution recommended. Note 4. The device is not guaranteed to function outside its operating conditions. Copyright © 2015 Richtek Technology Corporation. All rights reserved. www.richtek.com 6 is a registered trademark of Richtek Technology Corporation. DS5796C-00 February 2015 RT5796C Typical Application Circuit VIN CIN 10μF RT5796C LX VIN L EN CFF* VOUT COUT R1 FB PG* GND R2 *For TSOT-23-6 Package Only *CFF : Optional for performance fine-tune Table 1. Suggested Component Values VOUT (V) R1 (k) R2 (k) L (H) COUT (F) 3.3 90 20 1 to 3.3 10 1.8 100 50 1 to 3.3 10 1.5 100 66.6 1 to 3.3 10 1.2 100 100 1 to 3.3 10 1.05 100 133 1 to 3.3 10 1 100 148 1 to 3.3 10 Copyright © 2015 Richtek Technology Corporation. All rights reserved. DS5796C-00 February 2015 is a registered trademark of Richtek Technology Corporation. www.richtek.com 7 RT5796C Typical Operating Characteristics Efficiency vs. Output Current 100 90 90 80 VIN = 5V, VOUT = 3.3V 70 VIN = 3.3V, VOUT = 1.2V Efficiency (%) Efficiency (%) Efficiency vs. Output Current 100 60 50 40 30 80 VIN = 5V, VOUT = 3.3V 70 VIN = 3.3V, VOUT = 1.2V 60 50 40 30 20 20 10 10 0 0 0.25 0.5 0.75 1 1.25 0 0.001 1.5 0.01 Output Current (A) Output Voltage vs. Output Current 3.40 1.26 3.38 1.24 1.22 1.20 1.18 1.16 10 3.36 3.34 3.32 3.30 3.28 1.14 VIN = 5V, VOUT = 3.3V VIN = 3.3V, VOUT = 1.2V 1.12 3.26 0 0.25 0.5 0.75 1 1.25 1.5 0 0.25 Output Current (A) 0.5 0.75 1 1.25 1.5 Output Current (A) Output Voltage vs. Input Voltage Output Voltage vs. Input Voltage 1.26 3.40 3.38 Output Voltage (V) 1.24 Output Voltage (V) 1 Output Voltage vs. Output Current 1.28 Output Voltage (V) Output Voltage (V) 0.1 Output Current (A) 1.22 1.20 1.18 1.16 3.36 3.34 3.32 3.30 3.28 3.26 1.14 3.24 VIN = 4.3V to 5.5V, V OUT = 3.3V, IOUT = 1A VIN = 2.5V to 5.5V, V OUT = 1.2V, IOUT = 1A 1.12 2.5 3 3.5 4 4.5 5 Input Voltage (V) Copyright © 2015 Richtek Technology Corporation. All rights reserved. www.richtek.com 8 3.22 5.5 4.3 4.5 4.7 4.9 5.1 5.3 5.5 Input Voltage (V) is a registered trademark of Richtek Technology Corporation. DS5796C-00 February 2015 RT5796C Reference Voltage vs Input Voltage Switching Frequency vs. Input Voltage 1.5 0.64 1.4 Switcing Frequency (MHz)1 0.65 Reference Voltage (V) 0.63 0.62 0.61 0.60 0.59 0.58 0.57 0.56 VIN = 2.5V to 5.5V, IOUT = 1A 0.55 2.5 3 3.5 4 4.5 5 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 VOUT = 1.2V, IOUT = 0.5A 0.5 5.5 2.5 3 3.5 4.5 5 5.5 Shutdown Currrent vs. Temperature 1.0 5.0 0.9 4.5 0.8 Shutdown Current (μA)1 Shutdown Current (µA)1 Shutdown Current vs. Input Voltage 0.7 0.6 0.5 0.4 0.3 0.2 0.1 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 VEN = 0 EN = 0 -0.1 0.0 2.5 3 3.5 4 4.5 5 5.5 -50 -25 0 Input Voltage (V) 25 50 75 100 125 Temperature (°C) Quiescent Current vs. Temperature Quiescent Current vs. Input Voltage 0.050 40 0.045 35 0.040 Quiescent Current (µA) Quiescent Current (mA) 4 Input Voltage (V) Input Voltage(V) 0.035 0.030 0.025 0.020 0.015 0.010 30 VIN = 5V 25 20 VIN = 3.3V 15 10 5 0.005 VFB = 0.63V, LX No Switch 0 0.000 2.5 3 3.5 4 4.5 5 Input Voltage(V) Copyright © 2015 Richtek Technology Corporation. All rights reserved. DS5796C-00 February 2015 5.5 -50 -25 0 25 50 75 100 125 Temperature (°C) is a registered trademark of Richtek Technology Corporation. www.richtek.com 9 RT5796C Inductor Current Limit vs. Temperature 3.0 3.0 2.5 2.5 Inductor Current (A) Inductor Current (A) Inductor Current Limit vs. Input Voltage 2.0 1.5 1.0 2.0 1.5 1.0 0.5 0.5 VOUT = 1.2V VOUT = 1.2V 0.0 0.0 2.5 3 3.5 4 4.5 5 -50 5.5 -25 0 50 75 100 125 Temperature (°C) Input Voltage (V) Input UVLO vs. Temperature Enable Threshold vs. Temperature 2.5 1.4 2.4 1.2 2.3 Turn On Enable Voltage (V) Input Voltage (V) 25 2.2 2.1 2.0 1.9 Turn Off 1.8 1.0 Enable On 0.8 Enable Off 0.6 0.4 1.7 0.2 1.6 VEN = 3.3V 1.5 VIN = 3.3V 0.0 -50 -25 0 25 50 75 100 125 -50 0 25 50 75 100 Temperature (°C) Load Transient Response Load Transient Response VIN = 3.3V, VOUT = 1.2V, IOUT = 0A to 1.5A, CFF = 22pF VOUT (50mV/Div) 125 VIN = 3.3V, VOUT = 1.2V, IOUT = 0.5A to 1.5A, CFF = 22pF VOUT (50mV/Div) IOUT IOUT (1A/Div) (1A/Div) Time (100s/Div) Copyright © 2015 Richtek Technology Corporation. All rights reserved. www.richtek.com 10 -25 Temperature (°C) Time (100s/Div) is a registered trademark of Richtek Technology Corporation. DS5796C-00 February 2015 RT5796C Voltage Ripple Voltage Ripple VOUT (10mV/Div) VOUT (10mV/Div) VLX (2V/Div) VLX (2V/Div) VIN = 5V, VOUT = 3.3V, IOUT = 1A VIN = 3.3V, VOUT = 1.2V, IOUT = 1A Time (500ns/Div) Time (500ns/Div) Power On from EN Power Off from EN VEN (5V/Div) VPGOOD VEN (5V/Div) VPGOOD (2V/Div) (2V/Div) VOUT (1V/Div) VOUT (1V/Div) IOUT (1A/Div) IOUT (1A/Div) VIN = 3.3V, VOUT = 1.2V, IOUT = 1A Time (500s/Div) Time (10s/Div) Power On from EN Power Off from EN VEN (5V/Div) VEN (5V/Div) VPGOOD (2V/Div) VPGOOD (2V/Div) VOUT (2V/Div) IOUT (1A/Div) VOUT (2V/Div) IOUT (1A/Div) VIN = 5V, VOUT = 3.3V, IOUT = 1A Time (500s/Div) Copyright © 2015 Richtek Technology Corporation. All rights reserved. DS5796C-00 VIN = 3.3V, VOUT = 1.2V, IOUT = 1A February 2015 VIN = 5V, VOUT = 3.3V, IOUT = 1A Time (10s/Div) is a registered trademark of Richtek Technology Corporation. www.richtek.com 11 RT5796C Application Information The RT5796C is a single-phase step-down converter. It voltage across the capacitor. This voltage clamps the provides single feedback loop, constant on-time current mode control with fast transient response. An internal 0.6V reference allows the output voltage to be precisely regulated for low output voltage applications. A fixed switching frequency (1MHz) oscillator and internal compensation are integrated to minimize external voltage at the FB pin, causing PWM pulse width to increase slowly and in turn reduce the input surge current. The internal 0.6V reference takes over the loop control once the internal ramping-up voltage becomes higher than 0.6V. component count. Protection features include over current protection, under voltage protection and over temperature protection. Output Voltage Setting Connect a resistive voltage divider at the FB between VOUT and GND to adjust the output voltage. The output voltage is set according to the following equation : VOUT = VREF 1 R1 R2 where VREF is the feedback reference voltage 0.6V (typ.). VOUT UVLO Protection The RT5796C has input Under Voltage Lockout protection (UVLO). If the input voltage exceeds the UVLO rising threshold voltage (2.25V typ.), the converter resets and prepares the PWM for operation. If the input voltage falls below the UVLO falling threshold voltage during normal operation, the device will stop switching. The UVLO rising and falling threshold voltage has a hysteresis to prevent noise-caused reset. Inductor Selection The switching frequency (on-time) and operating point (% ripple or LIR) determine the inductor value as shown below: R1 L= FB VOUT VIN VOUT fSW LIR ILOAD(MAX) VIN R2 GND Figure 1. Setting VOUT with a Voltage Divider Chip Enable and Disable The EN pin allows for power sequencing between the controller bias voltage and another voltage rail. The RT5796C remains in shutdown if the EN pin is lower than 400mV. When the EN pin rises above the VEN trip point, the RT5796C begins a new initialization and soft-start cycle. Internal Soft-Start The RT5796C provides an internal soft-start function to prevent large inrush current and output voltage overshoot when the converter starts up. The soft-start where LIR is the ratio of the peak-to-peak ripple current to the average inductor current. Find a low loss inductor having the lowest possible DC resistance that fits in the allotted dimensions. The core must be large enough not to saturate at the peak inductor current (IPEAK) : IPEAK = ILOAD(MAX) + LIR ILOAD(MAX) 2 The calculation above serves as a general reference. To further improve transient response, the output inductor can be further reduced. This relation should be considered along with the selection of the output capacitor. Inductor saturation current should be chosen over IC’s current limit. (SS) automatically begins once the chip is enabled. During soft-start, the internal soft-start capacitor becomes charged and generates a linear ramping up Copyright © 2015 Richtek Technology Corporation. All rights reserved. www.richtek.com 12 is a registered trademark of Richtek Technology Corporation. DS5796C-00 February 2015 RT5796C Input Capacitor Selection VSAG = ILOAD ESR High quality ceramic input decoupling capacitor, such For a given output voltage sag specification, the ESR as X5R or X7R, with values greater than 10F are recommended for the input capacitor. The X5R and X7R ceramic capacitors are usually selected for power regulator capacitors because the dielectric material has less capacitance variation and more temperature stability. value can be determined. Voltage rating and current rating are the key parameters when selecting an input capacitor. Generally, selecting an input capacitor with voltage rating 1.5 times greater than the maximum input voltage is a conservatively safe design. better transient performance. Generally, using several capacitors connected in parallel can have better transient performance than using a single capacitor for the same total ESR. The input capacitor is used to supply the input RMS current, which can be approximately calculated using the following equation : For continuous operation, do not exceed absolute maximum junction temperature. The maximum power dissipation depends on the thermal resistance of the IC package, PCB layout, rate of surrounding airflow, and difference between junction and ambient temperature. The maximum power dissipation can be calculated by the following formula : IIN_RMS = ILOAD VOUT VOUT 1 VIN VIN The next step is selecting a proper capacitor for RMS current rating. One good design uses more than one capacitor with low equivalent series resistance (ESR) in parallel to form a capacitor bank. The input capacitance value determines the input ripple voltage of the regulator. The input voltage ripple can be approximately calculated using the following equation : VIN = IOUT(MAX) VOUT VOUT 1 CIN fSW VIN VIN Output Capacitor Selection The output capacitor and the inductor form a low pass filter in the Buck topology. In steady state condition, the ripple current flowing into/out of the capacitor results in ripple voltage. The output voltage ripple (VP-P) can be calculated by the following equation : Another parameter that has influence on the output voltage sag is the equivalent series inductance (ESL). The rapid change in load current results in di/dt during transient. Therefore, the ESL contributes to part of the voltage sag. Using a capacitor with low ESL can obtain Thermal Considerations PD(MAX) = (TJ(MAX) TA) / JA where TJ(MAX) is the maximum junction temperature, TA is the ambient temperature, and JA is the junction to ambient thermal resistance. For recommended operating condition specifications, the maximum junction temperature is 125C. The junction to ambient thermal resistance, JA, is layout dependent. For TSOT-23-5 package, the thermal resistance, JA, is 230.6C/W on a standard four-layer thermal test board. For TSOT-23-6 package, the thermal resistance, JA, is 197.4C/W on a standard four-layer thermal test board. The maximum power dissipation at TA = 25C can be calculated by the following formula : PD(MAX) = (125C 25C) / (230.6C/W) = 0.43W for 1 VP_P = LIR ILOAD(MAX) ESR + 8 COUT fSW TSOT-23-5 package When load transient occurs, the output capacitor supplies the load current before the controller can TSOT-23-6 package respond. Therefore, the ESR will dominate the output voltage sag during load transient. The output voltage undershoot (VSAG) can be calculated by the following equation : Copyright © 2015 Richtek Technology Corporation. All rights reserved. DS5796C-00 February 2015 PD(MAX) = (125C 25C) / (197.4C/W) = 0.5W for The maximum power dissipation depends on the operating ambient temperature for fixed TJ(MAX) and thermal resistance, JA. The derating curve in Figure 2 allows the designer to see the effect of rising ambient temperature on the maximum power dissipation. is a registered trademark of Richtek Technology Corporation. www.richtek.com 13 RT5796C Maximum Power Dissipation (W)1 1.0 Four-Layer PCB 0.9 0.8 0.7 0.6 TSOT-23-6 0.5 0.4 0.3 TSOT-23-5 0.2 0.1 0.0 0 25 50 75 100 125 Ambient Temperature (°C) Figure 2. Derating Curve of Maximum Power Dissipation Copyright © 2015 Richtek Technology Corporation. All rights reserved. www.richtek.com 14 is a registered trademark of Richtek Technology Corporation. DS5796C-00 February 2015 RT5796C Outline Dimension Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min Max A 0.700 1.000 0.028 0.039 A1 0.000 0.100 0.000 0.004 B 1.397 1.803 0.055 0.071 b 0.300 0.559 0.012 0.022 C 2.591 3.000 0.102 0.118 D 2.692 3.099 0.106 0.122 e 0.838 1.041 0.033 0.041 H 0.080 0.254 0.003 0.010 L 0.300 0.610 0.012 0.024 TSOT-23-5 Surface Mount Package Copyright © 2015 Richtek Technology Corporation. All rights reserved. DS5796C-00 February 2015 is a registered trademark of Richtek Technology Corporation. www.richtek.com 15 RT5796C Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min Max A 0.700 1.000 0.028 0.039 A1 0.000 0.100 0.000 0.004 B 1.397 1.803 0.055 0.071 b 0.300 0.559 0.012 0.022 C 2.591 3.000 0.102 0.118 D 2.692 3.099 0.106 0.122 e 0.838 1.041 0.033 0.041 H 0.080 0.254 0.003 0.010 L 0.300 0.610 0.012 0.024 TSOT-23-6 Surface Mount Package Richtek Technology Corporation 14F, No. 8, Tai Yuen 1st Street, Chupei City Hsinchu, Taiwan, R.O.C. Tel: (8863)5526789 Richtek products are sold by description only. Richtek reserves the right to change the circuitry and/or specifications without notice at any time. Customers should obtain the latest relevant information and data sheets before placing orders and should verify that such information is current and complete. Richtek cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Richtek product. Information furnished by Richtek is believed to be accurate and reliable. However, no responsibility is assumed by Richtek or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Richtek or its subsidiaries. Copyright © 2015 Richtek Technology Corporation. All rights reserved. www.richtek.com 16 is a registered trademark of Richtek Technology Corporation. DS5796C-00 February 2015