DC/DC Converters TSR 0.5 Series, 0.5 A Switching Regulator Features ◆ Compact SIP package ◆ Very high efficiency up to 97% ◆ Excellent line / load regulation ◆ Low standby current ◆ Operating temperature range –40 to 90°C ◆ Over-temperature protection ◆ Short circuit protection ◆ 3-year product warranty TSR-0.5 is a series of step-down non–isolated switching regulators in compact SIP package. These converters are an ideal drop-in replacement to LM78 linear regulators when energy efficiency is a parameter of the design. The high efficiency up to 97 % allows full load operation up to +80°C (+90°C with 50% load) ambient temperature without the need of forced aircooling. Excellent output voltage accuracy and low standby current are other features thatdistinguish switching regulators from linear regulators. Models Order code Input voltage range 1) Output voltage Output current max. Efficiency typ. @ Vin min. @ Vin 32VDC TSR 0.5-2415 1.5 VDC 73 % 63 % TSR 0.5-2418 1.8 VDC 82 % 71 % 2.5 VDC 87 % 77 % 91 % 81 % 94 % 86 % TSR 0.5-2425 4.75 – 32 VDC TSR 0.5-2433 TSR 0.5-2450 3.3 VDC 0.5 A 6.5 – 32 VDC 5.0 VDC TSR 0.5-2465 8 – 32 VDC 6.5 VDC 95 % 88 % TSR 0.5-2490 11 – 32 VDC 9.0 VDC 96 % 92 % TSR 0.5-24120 15 – 32 VDC 12 VDC 97 % 94 % TSR 0.5-24150 18 – 32 VDC 15 VDC 97 % 95 % 1) For input voltage higher 24 VDC an input capacitor 22 µF/ 50 V is required http://www.tracopower.com Page 1 of 3 DC/DC Converters TSR 0.5 Series 0.5 A Input Specifications No load input current (at 24Vin) 5 mA typ. Short circuit input power 1.5 W max. Surge voltage –0.3 / 34 VDC max. Input filter internal capacitor, see filter suggestion page 3 for to meet EN55022 class A, class B ESD (electrostatic discharge) EN 61000-4-2, air ±8 kV, perf. criteria A Radiated immunity EN 61000-4-3 3 V/m, perf. criteria A Fast transient EN 61000-4-4, ±0.5 kV, perf. criteria A with external input capacitor e.g. Nippon chemi-con KY 330 µF, 100 V Conducted immunity EN 61000-4-6, 3 Vrms, perf. criteria A Magnetic field immunity EN 61000-4-8, 3 A/m, perf. criteria A Output Specifications Voltage set accuracy ±3 % (at full load) Regulation – Input variation 1.5 to 6.5 Vin models: other models: – Load variation (10 – 100 %) 1.5 to 6.5 Vin models: other models: 0.4 % 0.2 % 0.6 % 0.4 % Minimum load not required Ripple and noise 1.5 to 6.5 Vin models: 30 mVp-p max. other models: 40 mVp-p max. Temperature coefficient ±0.015 %/K max. Dynamic load (50% load step change) – Peak variation ±2 % max. – Response time 100 µS max. Short circuit protection continuous, automatic recovery Current limitation 1.0 A max. Capacitive load 220 µF max. General Specifications Temperature ranges – Operating –40°C to +90°C – Case temperature +100°C. max. – Storage –55°C to +125°C Derating – positive output circuit 5 %/K above +80°C Overtemperature protection at +160°C (on internal IC) Humidity (non condensing) 95 % rel H max. Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >2´000’000 h Isolation voltage none Switching frequency Environmental compliance 330 kHz ±50 kHz (pulse width modulation) – Reach www.tracopower.com/products/reach-declaration.pdf – RoHS RoHS directive 2011/65/EU Physical Specifications Casing material non-conductive plastic (UL94V-0 rated) Pin material alloy 42 Weight 1.95 g (0.69 oz) Lead temperature 260°C Washing baking after washing: 100°C for 30 min. All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters TSR-0.5 Series 0.5 A Applications notes EMI filter for EN 55022 class A & B L1 C1 Class C1 C2 C2 & C3 A – B 4.7 µF / 50 V 1206 MLCC 4.7 µF / 50 V 1206 MLCC C3 +Vin +Vout TSR 0.5SM GND Load L1 value order code (SMD type) datasheet: 3.3 µH TCK-044 www.tracopower.com/products/tck044.pdf 10 µH TCK-047 www.tracopower.com/products/tck047.pdf Outline Dimensions 1 +Vin 2 GND 3 +Vout 4.1 [0.16] 0.5 [0.02] Pinout 10.2 [0.40] 0.5 [0.02] 11.5 [0.45] 1 2 3 Bottom View 7.55 [0.30] 0.70 [0.03] 2.0 [0.08] 2x2.54 [2x0.10] 0.25 [0.01] 3.2 [0.13] 10.5 [0.41] Dimensions in [mm], () = Inch Tolerances: ±0.5 (±0.02) Pin pich tolerances: ±0.25 (±0.01) Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com www.tracopower.com Rev. January 13. 2015 Page 3 of 3