SZD20CD - Teledyne Relays

ZD20CD Series
1A, 80 Vdc Optically Isolated
Short-Circuit Protected
FEATURES/BENEFITS
• Short-circuit protected
• Overload trip
• Low off-state leakage current
• Optical isolation
• Compact package
Part Number
Description
ZD20CD*
1A, 80 Vdc, short-circuit protected
up to 60 Vdc, solid-state relay for
through-hole mounting
SZD20CD*
1A, 80 Vdc, short-circuit protected up
to 60 Vdc, solid-state relay for surface
mount
MECHANICAL SPECIFICATIONS
*T, W level screening available
ELECTRICAL SPECIFICATIONS
(–55°C to +105°C ambient temperature
unless otherwise specified)
INPUT (CONTROL) SPECIFICATIONS
Min
Max
Input Current
8
20
mA
Input Voltage @10mA
2
3
Vdc
Must Turn-On
8
Must Turn-Off Current
mA
100
µA
0.8
Vdc
Must Turn-Off Voltage
Reverse Polarity
Units
–6
Vdc
OUTPUT (LOAD) SPECIFICATIONS
Load Voltage Range
Max
Units
80
Vdc
1.0
A
0
Output Current Rating (See Figure 6)
Figure 1
Leakage Current at Rated Voltage
20
µA
Transient Blocking Voltage @25°C
100
Vdc
**
Output Capacitance @25Vdc (25°C)
600
pF
Output Voltage Drop @1A
0.55
Vdc
On Resistance
0.55
Ohm
Turn-On Time
2.0
ms
Turn-Off Time
1.0
ms
Trip Overload
(See Figure 7)
Short Circuit Protection
Rs
*
A
60
TYPICAL WIRING DIAGRAM
Vdc
1
6
2
5
ZD
Min
3
4
LOAD
*
LOAD
*Shorted internally
**Series resistor required to limit input current to 20mA maximum
Figure 2
FUNCTIONAL BLOCK DIAGRAM
+IN (1)
INPUT
with
LEDs
Optical
Isolation
Detection
Circuit
Switching
Circuit
Output Switch
(MOSFET)
with Current
Sense
+OUT (6)
–OUT (4)
–IN (3)
Figure 3
© 2004 TELEDYNE RELAYS
(800) 284-7007 • www.teledynerelays.com
ZD Page 1
2DSZD20CD Rev --
ZD20CD Series
1A, 80 Vdc Optically Isolated
Short-Circuit Protected
GENERAL SPECIFICATIONS
(+25°C ambient temperature unless otherwise specified)
CONTROL CURRENT VS. INPUT VOLTAGE
Max
Units
Operating Temperature
–55
+105
°C
Storage Temperature
–55
+125
°C
Junction Temperature @1A
+125
°C
Thermal Resistance θJA
+125
°C/W
Shock
1500
g
Vibration
100
g
Dielectric Strength
1500
Vac
109
Ohm
Input to Output Capacitance
5
18
16
Control Current (mA)
Min
Insulation Resistance
(@500 Vdc)
+105°C +25°C –55°C
20
ENVIRONMENTAL SPECIFICATIONS
14
12
10
8
6
4
2
0
0
.5
1.0
1.5
pF
MIL STD 202, method 208
Thermal Shock
MIL STD 202, method 107
2.5
3.0
3.5
Figure 4
Resistance to Soldering Heat MIL STD 202, method 210
Solderability
2.0
Volts
LOAD CURRENT VS. AMBIENT TEMPERATURE
1.2
TYPICAL TURN-ON TIME VS. INPUT CURRENT
Load Current (A)
1.0
0.8
0.6
0.4
0.2
0
–55
–35
–15
5
25
45
65
85
105
125
Ambient Temperature (°C)
Figure 6
Figure 5
TYPICAL OVERLOAD TRIP CURRENT VS. TIME
Figure 7
ZD Page 2
NOTES:
1. The ZD20CD relay’s input current should be
limited to between 8 and 20mA. An external
resistor whose value =(VIN – 2.5 volts) ÷ 0.012
Amps is a good choice for limiting input current.
2. Relay input transitions should be less than 1.0
millisecond.
3. Loads may be attached to either the positive or
negative output terminal.
4. Maximum load current ratings are with the
relay in free air and soldered to a printed circuit
board.
5. Timing is measured from the input current
transition to the 10% or 90% points on the
output voltage transition.
6. Overload conditions (including shorted loads)
are specified for load supply voltages to 60 Vdc
maximum.
7. For through-hole-PCB-solder-attaching
ZD20CD series relays, the wave-solder or
solder pot operations are limited to +260°C
maximum for 10 seconds, maximum.
8. For surface-mount-solder-attaching SZD20CD
series relays, in IR heating or convection
heating systems, the component temperature
is limited to +235°C maximum for 10 seconds
maximum.
SPECIFICATIONS UNDER REVISION CONTROL
© 2004 TELEDYNE RELAYS
2DSZD20CD Rev --