Series CA 1A, 250 Vrms Optically Isolated AC Solid-State Relay Part Number* Relay Description CA00HD 1A, 250 Vrms, AC Solid-State Relay with dual in-line terminals. SCA00HD 1A, 250 Vrms, AC Solid-State Relay with gull wing surface mount terminals. * The Y suffix denotes parameters tested to MIL-PRF-28750 test methods. The W suffix denotes parameters tested to Teledyne specifications. FEATURES/BENEFITS • Optical Isolation: Isolates control elements from load transients. ELECTRICAL SPECIFICATIONS • Low Zero Cross Window: Minimizes switching transients and lowers EMI. Ideal as an SCR or TRIAC driver. (-55°C TO +105°C UNLESS OTHERWISE SPECIFIED) INPUT (CONTROL) CHARACTERISTICS 2 Terminal Configuration (See Fig. 1) Min Max Units Input Voltage 3.8 32 Vdc Input Current (See Figure 1) VIN = 5 Vdc VIN=32 Vdc 13 13 15 18 mA mA 1.5 Vdc Turn-Off Voltage (Guaranteed Off) Turn-On Voltage (Guaranteed On) Reverse Voltage Protection BLOCK DIAGRAM © 2003 TELEDYNE RELAYS 3.8 Vdc -32 Vdc • Fully Floating Output: Eliminates ground potential loops • Meets MIL-STD-704 Requirements for Relay Outputs: Allows relay to be used in avionic systems without external transient protection. • Buffered Control: Relay can be controlled directly from TTL or CMOS logic circuits. • Low-Profile Ceramic DIP Package: Allows high-density packaging for through-hole and surface-mount applications. DESCRIPTION The Series CA is designed for printed circuit board mounting in AC power switching applications. The relay is rated for 1A at 250 Vrms from 40 to 440 Hz for resistive and reactive loads with power factors as low as 0.2. Inverse parallel SCRs are configured for zero voltage turn on. The patented circuit design assures the lowest possible EMI by reducing commutation spikes. Optical isolation allows a floating output with 1200 Vac isolation between the control (input) and load (output). This allows low level logic circuits to safely control AC loads.The low profile ceramic DIP package is hermetically sealed to withstand severe environmental conditions encountered in military and aerospace applications. This relay is available with conventional leads for through-hole PCB mounting or with gull wing leads for surface mount applications. (800) 284-7007 • www.teledynerelays.com CA 1 CA\042003\Q1 Series CA ELECTRICAL SPECIFICATIONS MECHANICAL SPECIFICATIONS (-55°C TO +105°C UNLESS OTHERWISE SPECIFIED) 3 TERMINAL CONFIGURATION (SEE FIG. 1) Min Bias Voltage 3.8 Bias Current (VIN=32 Vdc) 0.560 (14.22) MAX 0.010 ± .002 (0.25 ± .05) 6 PLS INPUT (CONTROL) SPECIFICATIONS Max Units 32 Vdc 16 mA 18 Vdc 8 7 16170 CA00HD 0.395 (10.03) MAX 0.400 ± .015 (10.16 ± .38) 5 4 1 2 TOP INDEX MARK FOR PIN 1 (See Figure 2) SIDE INDEX MARK FOR PIN 1 Control Voltage Range 0 0.155 (3.94) MAX +.010 Control Current (at 5 Vdc) 250 µAdc Turn-On Control Voltage 0.3 Vdc Turn-Off Control Voltage 3.2 0.016 –.005 (0.41 +.25 –.13 ) 6 PLS .150 ± .015 6 PLS 0.100 (2.54) 0.125 (3.18) Vdc 0.018 ± .002 (0.46 ± .05) 6 PLS 0.300 (7.62) OUTPUT (LOAD) SPECIFICATIONS Min Max Units Output Current Rating (See Figure 3) 0.1 1.0 Arms Output Voltage Rating 20 250 Vrms Frequency Range 40 440 Hz Output Voltage Drop @ 1 Amp 1.5 Vrms Off-State Leakage Current 1.0 mArms PIN-OUTS PIN NO. FUNCTION 1 V(BIAS) 2 V(CNTRL) 4 LOAD 5 LOAD 7 N/C 8 INPUT COM. LOT NUMBER AND DATE CODE LOCATED ON THE BOTTOM SIDE PCB STYLE MECHANICAL OUTLINE (250 Vac, 400 Hz) 0.560 (14.22) MAX 8 0.477 (12.12 Turn-On Time 1/2 Cycle Turn-Off Time 1 Cycle +500 Vpk Transient Voltage (T < 5 s) (see Note 4) o Surge Current @ 25 C (16 ms) 5.6 Apk Zero Voltage Turn-On Point +18 Vpk dv/dt (See Note 1) 100 Load Power Factor 0.2 Insulation Resistance @ 500 Vdc 109 +.010 –.005 +.25 –.13 5 ) 0.395 (10.03) MAX 0.010 ± .002 (0.25 ± .05) 6 PLS 0.020 MIN 6 PLS PIN-OUTS PIN NO. FUNCTION 1 V(BIAS) 2 V(CNTRL) 4 LOAD 5 LOAD 7 N/C 8 INPUT COM. V/µs 7 16170 SCA00HD 4 1 2 TOP INDEX MARK FOR PIN 1 SIDE INDEX MARK FOR PIN 1 0.155 (3.94) MAX 0.020 (0.51) 6 PLS 0.125 (3.18) 0.025 (0.64) MIN. 6 PLS 0.100 (2.54) 0.300 (7.62) 0.018 ± .002 (0.46 ± .05) 6 PLS 1 0.066 (1.68) MIN. 6 PLS Input to Output Capacitance Ohms 5 Dielectric Withstanding Voltage (60Hz) 1200 Junction Temperature at Rated Current (TJ Max) Thermal Resistance Junction to Ambient (θJA) pF Vac o 130 85 C o C/W 0.390 (9.91) 0.522 (13.26) REF 0.300 (7.62) TYP 0.100 (2.54) TYP SURFACE MOUNT LAND PATTERN LOT NUMBER AND DATE CODE LOCATED ON THE BOTTOM SIDE SMT STYLE MECHANICAL OUTLINE TOLERANCES: .XX= ± .010 (± .25), .XXX= ± .005 (± .13) DIMENSION STYLES: XXX= INCHES (XXX)= MILLIMETERS CONTROLLING DIMENSIONS ARE IN INCHES. METRIC DIMENSIONS ARE SUPPLIED FOR REFERENCE PURPOSES ONLY. • WEIGHT: 2 gm max • CASE: DIP, hermetically sealed, ceramic • PINS: Gold plated CA 2 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE © 2003 TELEDYNE RELAYS CA\042003\Q1 Series CA ENVIRONMENTAL SPECIFICATIONS Ambient Temperature -55o C to +105o C Operating -55o C to +130o C Storage Acceleration 5000 g INPUT CURRENT VS VOLTAGE FIGURE 2 LOAD CURRENT DERATING CURVE FIGURE 3 WIRING CONFIGURATIONS FIGURE 1 (SEE NOTE 2) © 2003 TELEDYNE RELAYS (800) 284-7007 • www.teledynerelays.com CA 3 CA\042003\Q1 Series CA MAXIMUM VOLTAGE DROP VS AMBIENT TEMPERATURE AT IL RATED SERIES LIMIT BIAS RESISTOR VS BIAS VOLTAGE FIGURE 5 (SEE NOTE 3) FIGURE 4 NOTES: 1. To increase the dV/dt characteristic to 200V/µs, use an RC snubber across the output terminals with R =100 and C = 0.01 µF. 2. Control input is compatible with CMOS or open collector TTL (with pull up resistor). 3. For bias voltages above 6V, a series resistor is required. Use a standard resistor value equal to or less than the value found from Figure 5. 4. Output may temporarily lose blocking capability during and after a surge, until TJ falls below maximum. 5. Input transition should be ≤ 1 msec duration and input drive should be “bounceless contact” type. 6. Unless otherwise noted, the input voltage for functional tests shall be 5 Vdc. CA 4 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE © 2003 TELEDYNE RELAYS CA\042003\Q1