AZ770 SPDT SUBMINIATURE POWER RELAY FEATURES • • • • • • • • 5 kV dielectric strength, 10 kV surge 8 mm creepage and clearance Proof tracking index (PTI/CTI) 250 5 Amp switching capability (version “T” 10 Amp) 20 A high inrush current (1 Form A) Epoxy sealed version available UL Class F insulation (155°C) standard Reinforced insulation, EN 60730-1 (VDE 0631, part 1), 1 Form A: EN 60335-1 (VDE 0700, part 1) • UL, CUR file E44211 • VDE certificate 40006815 GENERAL DATA CONTACTS Arrangement SPST (1 Form A) SPDT (1 Form C) Ratings Resistive load: Max. switched power: (Version “T”: Max. switched current: (Version “T”: Max. switched voltage: 150 W or 1250 VA 150 W or 2500 VA) 5A 10 A) 30 VDC* or 250 VAC * Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Rated Load UL 1 Form A 5 A at 250 VAC, resistive, 100k cycles 5 A at 30 VDC, resistive, 100k cycles 3 A at 250 VAC, cos phi 0.4, 100k cycles 1/8 HP at 125/250 VAC, 100k cycles C300 pilot duty, 125/250 VAC, 100k cycles TV-2 at 120 VAC 1 Form C 3 A at 250 VAC, resistive, 100k cycles 3 A at 30 VDC, resistive, 100k cycles High capacity version “T” 10 A at 250 VAC, resistive, 85°C, 100k cycles 15 A at 120 VAC, resistive, 70°C, 6k cycles B300 pilot duty, 40°C 1000 W, 250 VAC, tungsten load, 40°C, 6k cycles VDE Material Resistance 5 A at 250 VAC, 85°C, 100k cycles 2 A at 250 VAC, cos phi 0.5, 85°C, 30k cycles * 3 A at 400 VAC, 85°C, 100k cycles Life Expectancy Mechanical Minimum operations 1 x 106 Standard version Electrical 1 x 105 at 5 A 250 VAC Res. High capacity version “T” Electrical 1 x 105 at 10 A 250 VAC Res. Operate Time (max.) 8 ms at nominal coil voltage Release Time (max.) 4 ms at nominal coil voltage (with no coil suppression) Dielectric Strength (at sea level for 1 min.) 5000 Vrms coil to contact 1000 Vrms between open contacts Surge Voltage Coil to contact 10,000 V (at 1.2x50 µs) Insulation Resistance 1000 megohms min. at 20°C, 500 VDC, 50% RH Insulation (according to DIN VDE 0110, IEC 60664-1) C250 Overvoltage category: III Pollution dregree: 3 Nominal voltage: 250 VAC Dropout Greater than 5% of nominal coil voltage Ambient Temperature Operating At nominal coil voltage -40°C (-40°F) to 85°C (185°F) Vibration 1.65 mm DA at 10–55 Hz Shock 10 g operating, 100 g damage Enclosure P.B.T. polyester Terminals Tinned copper alloy, P.C. Max. Solder Temp. 270°C (518°F) * change-over contact tested as make contact Max. Solder Time 5 seconds High capacity version “T” 10 A at 250 VAC, 85°C, 15k cycles Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 4.6 grams Packing unit in pcs 100 per tray / 1000 per carton box Silver nickel, silver tin oxide (high capacity version “T” only), gold plating available < 100 milliohms initially ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2014-09-26 AZ770 NOTES COIL Power At Pickup Voltage (typical) 253 mW (standard coil) 113 mW (sensitive coil) 130 mW (sensitive coil high capacity version “T”) Max. Continuous Dissipation 760 mW at 20°C (68°F) ambient Temperature Rise (at nominal voltage) 41°C (74°F) standard coil 22°C (40°F) sensitive coil 27°C (49°F) sensitive coil high capacity version “T” Temperature 1. All values at 20°C (68°F) 2. Relay may pull in with less than “Must Operate” value. 3. The vibration resistance is 0.6 mm DA at 10–55 Hz for the N.C. contact, if vibration is in length direction. 4. Specifications subject to change without notice. Max. 155°C (311°F) RELAY ORDERING DATA STANDARD COIL - TYPE 1 FOOTPRINT COIL SPECIFICATIONS Nominal Coil VDC Must Operate VDC ORDER NUMBER* Max. Continuous VDC Coil Resistance Ohm ± 10 Form A (SPST) Form C (SPDT) 3 2.25 3.9 20 AZ770-1A-3D AZ770-1C-3D 5 3.75 6.6 55 AZ770-1A-5D AZ770-1C-5D 6 4.50 7.8 80 AZ770-1A-6D AZ770-1C-6D 9 6.75 11.7 180 AZ770-1A-9D AZ770-1C-9D 12 9.00 15.6 320 AZ770-1A-12D AZ770-1C-12D 18 13.50 23.4 720 AZ770-1A-18D AZ770-1C-18D 24 18.00 31.2 1,280 AZ770-1A-24D AZ770-1C-24D 48 36.00 62.4 5,120 AZ770-1A-48D AZ770-1C-48D * “1A” or “1C” denote silver nickel contacts. Substitute “AZ770T-1AE” in place of “AZ770-1A” for high capacity version. Add suffix “E” at the end of order number for sealed version. Add suffix “K” at the end of order number for different footprint. Add suffix “G” at the end of order number for gold plated contacts. SENSITIVE COIL (STANDARD VERSION) - TYPE 1 FOOTPRINT COIL SPECIFICATIONS Nominal Coil VDC Must Operate VDC Max. Continuous VDC ORDER NUMBER* Coil Resistance Ohm ± 10% Form A (SPST) 3 2.25 5.1 45 AZ770-1A-3DS 5 3.75 8.5 125 AZ770-1A-5DS 6 4.50 10.2 180 AZ770-1A-6DS 9 6.75 15.3 400 AZ770-1A-9DS 12 9.00 20.4 720 AZ770-1A-12DS 18 13.50 30.6 1,600 AZ770-1A-18DS 24 18.00 40.8 2,800 AZ770-1A-24DS * “1A” denote silver nickel contacts. Add suffix “E” at the end of order number for sealed version. Add suffix “K” at the end of order number for different footprint (Type 2). Add suffix “G” at the end of order number for gold plated contacts. ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2014-09-26 AZ770 SENSITIVE COIL (HIGH CAPACITY VERSION “T”) - TYPE 1 FOOTPRINT COIL SPECIFICATIONS Nominal Coil VDC Must Operate VDC 3 2.25 5 6 ORDER NUMBER* Max. Continuous VDC Coil Resistance Ohm ± 10% Form A (SPST) 5.1 38 AZ770T-1AE-3DS 3.75 8.5 108 AZ770T-1AE-5DS 4.50 10.2 155 AZ770T-1AE-6DS 9 6.75 15.3 350 AZ770T-1AE-9DS 12 9.00 20.4 620 AZ770T-1AE-12DS 18 13.50 30.6 1,390 AZ770T-1AE-18DS 24 18.00 40.8 2,480 AZ770T-1AE-24DS 48 36.00 81.6 9,920 AZ770T-1AE-48DS * “1AE” denote silver tin oxide contacts. Add suffix “E” at the end of order number for sealed version. Add suffix “K” at the end of order number for different footprint (Type 2). Add suffix “G” at the end of order number for gold plated contacts. MECHANICAL DATA PC BOARD LAYOUT .703 Max [17.85] .407 Max [10.35] 5 x ø .05 [ø 1.3] .494 Max [12.55] .157 [4] ø .02 [ø 0.5] 2 x .012 [0.3] .60 [15.24] .25 [6.35] .30 [7.6] .06 [1.5] Type 1 Type 1 .016 [0.4] 3 x .012 [0.3] *Not used on Form A version WIRING DIAGRAMS .407 Max [10.35] 3 1 3 1 4 5 2 ø .02 [0.5] Type 2 Viewed toward terminals .494 Max [12.55] .157 [4] * .157 [4.0] .03 [0.8] .1 [2.54] .30 [7.6] * .016 [0.4] .703 Max [17.85] .50 [12.7] 5 x ø .05 [ø 1.3] 2 * Type 1 .03 [0.8] 4 5 * Type 2 Viewed toward terminals *Not used on Form A version Type 2 Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2014-09-26