AZ762 16 A SPDT MINIATURE POWER RELAY FEATURES • • • • • Dielectric strength 5000 Vrms High Inrush version (80 A) available AC and DC coils Isolation spacing greater than 10 mm Reinforced insulation, EN 60730-1 (VDE 0631, part 1), EN 60335-1 (VDE 0700, part 1) • UL, CUR file E44211 • VDE certificate 40006031 GENERAL DATA CONTACTS Arrangement SPDT (1 Form C) SPST (1 Form A) Ratings Resistive load: Max. switched power: 480 W or 5540 VA Max. switched current: 16 A Max. switched voltage: 125 VDC* or 440 VAC * Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Material Silver cadmium oxide [1], silver tin oxide [2], silver nickel [3]. Gold plating available Resistance < 50 miliohms initially COIL Minimum operations 1 x 107 1 x 105 at 16 A 250 VAC Res. Operate Time (typical) 7 ms at nominal coil voltage DC coils 10 ms at nominal coil voltage AC coils Release Time (typical) 3 ms at nominal coil voltage (with no coil suppression) Dielectric Strength 5000 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Insulation Resistance 1000 megohms min. at 20°C 500 VDC 50% RH Insulation (according to DIN VDE 0110, IEC 60664-1) C250 Overvoltage category: III Pollution degree: 3 Nominal voltage: 250 VAC Dropout Greater than 10% of nominal coil voltage Greater than 15% of nominal coil voltage DC coils AC coils Power At Pickup Voltage Life Expectancy Mechanical Electrical Ambient Temperature Operating At nominal coil voltage -40°C (-40°F) to 85°C (185°F) DC coils -40°C (-40°F) to 70°C (158°F) AC coils Vibration 0.062" (1.5 mm) DA at 10–55 Hz Shock 10 g Enclosure P.B.T. polyester (typical) 200 mW standard DC coil 140 mW sensitive DC coil .422 VA (AC coil) Max. Continuous Dissipation 1.7 W at 20°C (68°F) ambient 1.7 VA at 20°C (68°F) ambient Temperature Rise 26°C (47°F) standard coil (at nominal coil voltage) 17°C (31°F) sensitive coil Terminals Tinned copper alloy, P. C. Max. 130°C (266°F) Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 14 grams Packing unit in pcs 50 per plastic tray / 500 per carton box Temperature NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2014-01-29 AZ762 CONTACTS Rated Load UL, CUR 1 Form A / 1 Form C 16 A at 277 VAC, Resistive, 100k cycles, 85°C [3] 16 A at 277 VAC, Resistive, 75k cycles, 85°C [2] 16 A at 277 VAC, Resistive, 50k cycles, 85°C [1] 12 A at 277 VAC, Resistive, 100k cycles, 40°C, (N.O.) [1] 9.2 A at 120 VAC, General use, 100k cycles, 60°C [2] 9 A at 250 VAC, Resistive, 100 k cycles, 105°C [1] 8.2 A at 120 VAC, Resistive, 100k cycles, 60°C [2] 4 A at 347 VAC, General use, 6k cycles, 85°C, (N.C.) [1] 5 FLA / 30 LRA at 250 VAC, 30k cycles, 65°C [2] 5 FLA / 30 LRA at 250 VAC, 30k cycles, 65°C [3] * 1 HP at 250 VAC, 85°C [1] 1 HP at 277 VAC, 40°C, (N.O.) [1] 1/ HP at 250 VAC, 85°C [2] 2 1/ HP at 125 VAC, 85°C [1] 2 1/ HP at 125 VAC, 85°C [2] 3 Rated Load VDE 1 Form A - DC coil 16 A at 250 VAC, 50k cycles, 85°C [3] 16 A at 250 VAC, 20k cycles, 85°C [2] 16 A at 250 VAC, 30k cycles, 70°C [1] 12.5 A at 400 VAC, 30k cycles, 85°C [3] 10 A at 250 VAC, 100k cycles, 70°C [1] 9 A at 250 VAC, cos phi 0.4, 120k cycles, 70°C [1][2][3] 6 A at 400 VAC, 100k cycles, 85°C [3] 1 Form A - DC coil - high inrush version “I” 16 A at 250 VAC, 30k cycles, 85°C [2] 16 A at 400 VAC, 10k cycles, 85°C [2] 1 Form A - DC coil sensitive 10 A at 250 VAC, 100k cycles, 85°C [1] 10 A at 250 VAC, 20k cycles, 85°C [2] 6 A at 400 VAC, 100k cycles, 85°C [1] TV-5, 125 VAC, 85°C [1] B300, 85°C [2] R300, 85°C [2] 1 Form A - AC coil 16 A at 250 VAC, 50k cycles, 70°C [3] * approved for Class F version only 1 Form C - DC coil 16 A at 250 VAC, 20k cycles, 85°C [2] 16 A at 250 VAC, 30k cycles, 70°C [1] 12 A at 250 VAC, 50k cycles, 85°C [3] 16 A at 250 VAC, 10k cycles, 85°C [3] * 9 A at 250 VAC, cos phi 0.4, 120k cycles, 70°C [1][2][3] * 1 Form A - DC coil (without gold plating) 20 A at 277 VAC, Resistive, 40°C [2] 10 FLA / 60 LRA at 250 VAC, 40°C [2] 5 FLA / 30 LRA at 250 VAC, 30k cycles, 85°C [2] 1 HP at 250 VAC, 30k cycles, 40°C [2] 1/ HP at 125 VAC, 30k cycles, 40°C [2] 2 TV-5, 120 VAC, 40°C [2] * change-over contact tested as make contact 1 Form A - DC coil - high inrush version “I” 16 A at 250 VAC, General use, 75k cycles, 40°C [2] 1 Form C - DC coil sensitive 10 A at 250 VAC, 70k cycles, 85°C [1] 10 A at 250 VAC, 20k cycles, 85°C [2] 6 A at 400 VAC, 70k cycles, 85°C [1] 1 Form C - AC coil 16 A at 250 VAC, 20k cycles, 70°C [3] RELAY ORDERING DATA DC COIL SPECIFICATIONS – STANDARD COIL Nominal Coil VDC 5 ORDER NUMBER* Must Operate VDC 3.5 Max. Continuous VDC 10.2 Coil Resistance Ohm ± 10% 62 6 4.2 12.3 90 AZ762–1A–6D AZ762–1C–6D 9 6.3 18.3 200 AZ762–1A–9D AZ762–1C–9D 1 Form A 1 Form C AZ762–1A–5D AZ762–1C–5D 12 8.4 24.7 360 AZ762–1A–12D AZ762–1C–12D 18 12.6 37.0 810 AZ762–1A–18D AZ762–1C–18D 24 16.8 49.4 1,440 AZ762–1A–24D AZ762–1C–24D 48 33.6 98.0 5,760 AZ762–1A–48D AZ762–1C–48D 60 42.0 112.9 7,500 AZ762–1A–60D AZ762–1C–60D 110 77.0 206.9 25,200 AZ762–1A–110D AZ762–1C–110D * “1A” or “1C” denote silver cadmium oxide contacts. Add suffix “E” to “1A” or “1B” or “1C” for silver tin oxide contacts. Add suffix “B” to “1A” or “1B” or “1C” for silver nickel contacts. Add suffix “E” at the end of order number for sealed version. Add suffix “A” at the end of order number for gold plated contacts. Add suffix “I” at the end of part number for high inrush version 80 A (contact form “1AE” only, no gold plating). Add suffix “F” at the end of order number for Class F version. ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2014-01-29 AZ762 RELAY ORDERING DATA DC COIL SPECIFICATIONS – SENSITIVE COIL Nominal Coil VDC 5 Must Operate VDC 3.8 Max. Continuous VDC 13.0 ORDER NUMBER* Coil Resistance Ohm ± 10% 100 1 Form C 1 Form A AZ762–1A–5DS AZ762–1C–5DS 6 4.5 15.6 144 AZ762–1A–6DS AZ762–1C–6DS 12 9.0 31.3 576 AZ762–1A–12DS AZ762–1C–12DS 18 13.5 46.9 1,296 AZ762–1A–18DS AZ762–1C–18DS 24 18.0 62.6 2,304 AZ762–1A–24DS AZ762–1C–24DS 48 36.0 125.2 9,216 AZ762–1A–48DS AZ762–1C–48DS AZ762–1A–60DS AZ762–1C–60DS 60 45.0 147.8 12,867 * “1A” or “1C” denote silver cadmium oxide contacts. Add suffix “E” to “1A” or “1B” or “1C” for silver tin oxide contacts. Add suffix “B” to “1A” or “1B” or “1C” for silver nickel contacts. (Not VDE approved!) Add suffix “E” at the end of order number for sealed version. Add suffix “A” at the end of order number for gold plated contacts. Add suffix “F” at the end of order number for Class F version. AC COIL SPECIFICATIONS - STANDARD COIL Nominal Coil VAC Must Operate VAC ORDER NUMBER* Max. Continuous VAC Nominal Current mA ± 10% Coil Resistance Ohm ± 15% 1 Form A 1 Form C 24 18.0 31.2 31.6 350 AZ762–1A–24AF AZ762–1C–24AF 115 86.3 149.5 6.6 8,100 AZ762–1A–115AF AZ762–1C–115AF 230 172.5 299.0 3.2 32,500 * “1A” or “1C” denote silver cadmium oxide contacts. Add suffix “E” to “1A” or “1C” for silver tin oxide contacts. Add suffix “B” to “1A” or “1C” for silver nickel contacts. Add suffix “E” before “F” (AC coils) at the end of order number for sealed version. Add suffix “A” before “F” (AC coils) at the end of order number for gold plated contacts. AZ762–1A–230AF AZ762–1C–230AF MECHANICAL DATA PC BOARD LAYOUT 5.04 15.12 12.7 ± 0.3 29 ± 0.3 5.04 2.6 2.7 7.56 15.7 ± 0.3 * * 3.6 ± 0.5 0.3 ± 0.2 8 x ø 1.3 * Not used on 1 Form A relay Viewed toward terminals WIRING DIAGRAMS 2 x 0.5 x 0.5 6 x 0.5 7.56 6 x 0.8 1 Form A 5.04 15.12 4 5 1 Form C 2 4 5 3 2 2.6 5.04 8 7 1 8 7 6 1 Dimensions in millimeters. Tolerance: ± 0.25 mm ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2014-01-29