晶采光電科技股份有限公司 - Zettler Electronics

SPECIFICATIONS FOR
LCD MODULE
CUSTOMER
CUSTOMER PART NO.
AMPIRE PART NO.
APPROVED
AM-800600GTMQW-01H
BY
DATE
† Approved For Specifications
† Approved For Specifications & Sample
AMPIRE CO., LTD.
Building D., 2F., No.88, Sec. 1, Sintai 5th Rd., Sijhih City,
Taipei County 221, Taiwan (R.O.C.)
台北縣汐止市新台五路一段 88 號 2 樓(東方科學園區 D 棟)
TEL:886-2-26967269 , FAX:886-2-86967196 or 26967270
APPROVED BY
Date : 2008/6/25
CHECKED BY
AMPIRE CO., LTD.
ORGANIZED BY
1
RECORD
Revision Date Page
2008/6/25
Date : 2008/6/25
-
OF
REVISION
Contents
Editor
New Release
EricLin
AMPIRE CO., LTD.
2
1. Features
8 inch Amorphous-TFT-LCD (Thin Film Transistor Liquid Crystal Display) module.
This module is composed of a 8” TFT-LCD panel, LED backlight and T-CON board unit.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Construction: 8” a-Si TFT active matrix, White LED Backlight .
Resolution (pixel): 800(R.G.B) X600
Number of the Colors : 262K colors ( R , G , B 6 bit digital each)
LCD type : Transmissive , normally White
Interface: 40 pin
Power Supply Voltage: 3.3V single power input.
Viewing Direction: 6 O’clock (The direction it’s hard to be discolored )
2. PHYSICAL SPECIFICATIONS
Item
LCD size
Resolution
Specifications
unit
8 inch (Diagonal)
800 x 3(RGB) x 600
dot
0.0675(W) x 0.2025(H)
mm
Active area
162.0(W) x 121.5(H)
mm
Module size
183.0(W) x 141.0(H) x 8.85(D)
mm
Dot pitch
Surface treatment
Anti-Glare
Color arrangement
RGB-stripe
interface
Weight
Date : 2008/6/25
Digital
TBD
AMPIRE CO., LTD.
g
3
3. ELECTRICAL CHARACTERISTICS
3-1 Typical Operation Conditions
Values
Item
Symbol
UNIT
Min.
Typ.
Max.
Digital Power Supply
VCC
--
3.3
--
V
Digital Operating
Current
IVCC
--
120
132
mA
Power Consumption
PLCD
--
396
436
mW
Note
3-2 Backlight Driving Conditions
Values
Item
Symbol
Min.
Typ.
Max.
Unit
Note
LED voltage
VL
9.3
9.9
10.5
V
Note 1
LED current
IL
--
18
20
mA
Note 1
LED life time
--
20,000
--
--
Hr
Note 2
Note 1 : The LED driving condition is defined for each LED module. (3 LED Serial)
Note 2 : The “LED life time” is defined as the module brightness decrease to 50%
original brightness that ambient temperature is 25℃ and IL = 20mA.
Note 3 : When LCM is operated over 40℃ ambient temperature, the ILED of each LED
module (3 LED Serial) should be follow :
Date : 2008/6/25
AMPIRE CO., LTD.
4
4. Optical Specifications
Values
Item
Symbol
Viewing angle
(CR≧10)
Condition
Min.
Typ.
Max.
θL
Φ = 180°
(9 o’clock)
--
70
--
θR
Φ = 0°
(3 o’clock)
--
70
--
θT
Φ = 90°
(12 o’clock)
--
60
--
θB
Φ = 270°
(6 o’clock)
--
70
--
Unit
Note
degree
Note1
msec
Note3
Note4
Response time
Tr +Tf
--
25
Contrast ratio
CR
--
400
--
--
Rx
0.57
0.62
0.67
--
Ry
0.29
0.34
0.39
--
Gx
0.29
0.34
0.39
0.56
0.61
0.66
0.09
0.14
0.19
By
0.05
0.10
0.15
Wx
0.27
0.32
0.37
Wy
0.31
0.36
0.41
Luminance
L
250
300
--
cd/㎡
Note6
Luminance
uniformity
YU
70
75
--
%
Note7
Red
Green
Gy
Color
chromaticity
Bx
Normal
θ=Φ=0°
Note5
Note6
Blue
White
Test Conditions :
1. VCC = 3.3V, IL = 20mArms (Backlight current), the ambient temperature is
25℃.
2. The test systems refer to Note 2.
Note 1 : Definition of viewing angle range
Date : 2008/6/25
AMPIRE CO., LTD.
5
Note 2 : Definition of optical measurement system.
The optical characteristics should be measured in dark room. After 30 minutes
operation, the optical properties are measured at the center point of the LCD screen.
(Response time is measured by Photo detector TOPCON BM-7, other items are
measured by BM-5A/Field of view : 1° / Height : 500mm.)
Note 3 : Definition of Response time
The response time is defined as the LCD optical switching time interval
between “White” state and “Black” state. Rise time (TON) is the time between photo
detector output intensity changed from 90% to 10%. And fall time (TOFF) is the time
between photo detector output intensity changed from 10% to 90%.
Date : 2008/6/25
AMPIRE CO., LTD.
6
Note 4 : Definition of contrast ratio
Luminance measured when LCD on the “White” state
Contrast ratio (CR) =
Luminance measured when LCD on the “Black” state
Note 5 : Definition of color chromaticity (CIE1931)
Color coordinated measured at center point of LCD.
Note 6 : All input terminals LCD panel must be ground when measuring the center area
of the panel.
Note 7 : Definition of Luminance Uniformity
Active area is divided into 9 measuring areas (Refer to bellow figure). Every
measuring point is placed at the center of each measuring area.
Bmin
Luminance Uniformity (Yu) =
Bmax
Bmax : The measured maximum luminance of all measurement position.
Bmin : The measured minimum luminance of all measurement position.
L ----- Active area length
W ----- Active area width
Date : 2008/6/25
AMPIRE CO., LTD.
7
5. INTERFACE
5-1 TFT LCD Panel Driving Section
Pin No.
Symbol
I/O
1
GND
P
Power ground
2
GND
P
Power ground
3
NC
4
VCC
I
Power supply for digital circuit(3.3V)
Note 1
5
VCC
I
Power supply for digital circuit(3.3V)
Note 1
6
VCC
I
Power supply for digital circuit(3.3V)
Note 1
7
VCC
I
Power supply for digital circuit(3.3V)
Note 1
8
NC
9
DE
I
Data enable
10
GND
P
Power ground
11
GND
P
Power ground
12
GND
P
Power ground
13
B5
I
Blue data input (MSB)
14
B4
I
Blue data input
15
B3
I
Blue data input
16
GND
P
Power ground
17
B2
I
Blue data input
18
B1
I
Blue data input
19
B0
I
Blue data input (LSB)
20
GND
P
Power ground
21
G5
I
Green data input (MSB)
22
G4
I
Green data input
23
G3
I
Green data input
24
GND
P
Power ground
25
G2
I
Green data input
Date : 2008/6/25
Description
Note
NC
NC
AMPIRE CO., LTD.
8
26
G1
I
Green data input
27
G0
I
Green data input (LSB)
28
GND
P
Power ground
29
R5
I
Red data input (MSB)
30
R4
I
Red data input
31
R3
I
Red data input
32
GND
P
Power ground
33
R2
I
Red data input
34
R1
I
Red data input
35
R0
I
Red data input (LSB)
36
GND
P
Power ground
37
GND
P
Power ground
38
CLK
I
Clock Signal input. Latching data at the
Rising edge.
39
GND
P
Power ground
40
GND
P
Power ground
Note : input, O : output, P : power
Note 1: Typ. Vcc = 3.3V, Min. Vcc = 3.0V, Max. Vcc = 3.6V
5-2 Backlight Unit Section
Pin No.
Symbol
I/O
1
HI
P
Power supply for backlight unit
2
GND
P
Ground for backlight unit
Date : 2008/6/25
Description
AMPIRE CO., LTD.
Note
RED
BLACK
9
6. INPUT SIGNAL :
6-1 Timing Condition
Values
Parameter
Symbol
Unit
Min.
Typ.
Max.
CLK Frequency
FCPH
--
39.79
--
MHZ
CLK Period
FCPH
--
25.13
--
ns
CLK Pulse Duty
FCWH
40
50
60
%
DE Period
Fdeh+T
DEL
1000
1056
--
TCPH
DE Pulse Width
FDH
--
800
--
TCPH
DE Frame Blanking
FHS
10
28
110
DE Frame Width
FEP
--
600
--
OEV Pulse Width
TOEV
--
150
--
TCPH
OKV Pulse Width
TCKV
--
133
--
TCPH
DE(internal)-STV Time
T1
--
4
--
TCPH
DE(internal)-CKV Time
T2
40
TCPH
DE(internal)-OEV Time
T3
23
TCPH
DE(internal)-POL Time
T4
STV Pulse Width
-
--
157
1
--
Note
FDEH+
TDEL
FDEH+
TDEL
TCPH
TH
THS+THA<TH
Date : 2008/6/25
AMPIRE CO., LTD.
10
6-2 Timing Characteristic
Date : 2008/6/25
AMPIRE CO., LTD.
11
6-3 Block Diagram
Date : 2008/6/25
AMPIRE CO., LTD.
12
7. RELIABILITY TEST CONDITIONS
Test Item
Test Conditions
Note
High Temperature Operation
70±3°C , t=96 hrs
Low Temperature Operation
-20±3°C , t=96 hrs
High Temperature Storage
80±3°C , t=96 hrs
1,2
Low Temperature Storage
-30±3°C , t=96 hrs
1,2
Thermal Shock Test
-20°C ~ 25°C ~ 70°C
30 m in.
5 min. 30 min. ( 1 cycle ) 1,2
Total 5 cycle
Humidity Test
40 °C, Humidity 90%, 96 hrs
1,2
Note 1 : Condensation of water is not permitted on the module.
Note 2 : The module should be inspected after 1 hour storage in normal conditions
(15-35°C , 45-65%RH).
Definitions of life end point :
z
Current drain should be smaller than the specific value.
z
Function of the module should be maintained.
z
Appearance and display quality should not have degraded noticeably.
z
Contrast ratio should be greater than 50% of the initial value.
Date : 2008/6/25
AMPIRE CO., LTD.
13
8. USE PRECAUTIONS
8-1 Handling precautions
(1) The polarizing plate may break easily so be careful when handling it. Do not
touch, press or rub it with a hard-material tool like tweezers.
(2) Do not touch the polarizing plate surface with bare hands so as not to make it
dirty. If the surface or other related part of the polarizing plate is dirty, soak a soft
cotton cloth or chamois leather in benzine and wipe off with it. Do not use chemical
liquids such as acetone, toluene and isopropyl alcohol. Failure to do so may bring
chemical reaction phenomena and deteriorations.
(3) Remove any spit or water immediately. If it is left for hours, the suffered part may
deform or decolorize.
(4) If the LCD element breaks and any LC stuff leaks, do not suck or lick it. Also if
LC stuff is stuck on your skin or clothing, wash thoroughly with soap and water
immediately.
8-2 Installing precautions
(1) The PCB has many ICs that may be damaged easily by static electricity. To
prevent breaking by static electricity from the human body and clothing, earth the
human body properly using the high resistance and discharge static electricity
during the operation. In this case, however, the resistance value should be approx.
1MΩ and the resistance should be placed near the human body rather than the
ground surface. When the indoor space is dry, static electricity may occur easily so
be careful. We recommend the indoor space should be kept with humidity of 60% or
more. When a soldering iron or other similar tool is used for assembly, be sure to
earth it.
(2) When installing the module and ICs, do not bend or twist them. Failure to do so
may crack LC element and cause circuit failure.
(3) To protect LC element, especially polarizing plate, use a transparent protective
plate (e.g., acrylic plate, glass etc) for the product case.
(4) Do not use an adhesive like a both-side adhesive tape to make LCD surface
(polarizing plate) and product case stick together. Failure to do so may cause the
polarizing plate to peel off
8-3 Storage precautions
(1) Avoid a high temperature and humidity area. Keep the temperature between 0°C
and 35°C and also the humidity under 60%.
(2) Choose the dark spaces where the product is not exposed to direct sunlight or
fluorescent light.
(3) Store the products as they are put in the boxes provided from us or in the same
conditions as we recommend.
Date : 2008/6/25
AMPIRE CO., LTD.
14
8-4 Operating precautions
(1) Do not boost the applied drive voltage abnormally. Failure to do so may break
ICs. When applying power voltage, check the electrical features beforehand and be
careful. Always turn off the power to the LC module controller before removing or
inserting the LC module input connector. If the input connector is removed or
inserted while the power is turned on, the LC module internal circuit may break.
(2) The display response may be late if the operating temperature is under the
normal standard, and the display may be out of order if it is above the normal
standard. But this is not a failure; this will be restored if it is within the normal
standard.
(3) The LCD contrast varies depending on the visual angle, ambient temperature,
power voltage etc. Obtain the optimum contrast by adjusting the LC dive voltage.
(4) When carrying out the test, do not take the module out of the low-temperature
space suddenly. Failure to do so will cause the module condensing, leading to
malfunctions.
(5) Make certain that each signal noise level is within the standard (L level: 0.2Vdd
or less and H level: 0.8Vdd or more) even if the module has functioned properly. If it
is beyond the standard, the module may often malfunction. In addition, always
connect the module when making noise level measurements.
(6) The CMOS ICs are incorporated in the module and the pull-up and pull-down
function is not adopted for the input so avoid putting the input signal open while the
power is ON.
(7) The characteristic of the semiconductor element changes when it is exposed to
light emissions, therefore ICs on the LCD may malfunction if they receive light
emissions. To prevent these malfunctions, design and assemble ICs so that they are
shielded from light emissions.
(8) Crosstalk occurs because of characteristics of the LCD. In general, crosstalk
occurs when the regularized display is maintained. Also, crosstalk is affected by the
LC drive voltage. Design the contents of the display, considering crosstalk.
8-5 Other
(1) Do not disassemble or take the LC module into pieces. The LC modules once
disassembled or taken into pieces are not the guarantee articles.
(2) The residual image may exist if the same display pattern is shown for hours. This
residual image, however, disappears when another display pattern is shown or the
drive is interrupted and left for a while. But this is not a problem on reliability.
(3) AMIPRE will provide one year warrantee for all products and three months
warrantee for all repairing products.
Date : 2008/6/25
AMPIRE CO., LTD.
15
晶采 光 電 科技
9. OUTLINE DIMENSION
Date : 2008/6/25
AMPIRE CO., LTD.
16