SPECIFICATIONS FOR LCD MODULE CUSTOMER CUSTOMER PART NO. AMPIRE PART NO. APPROVED AM-640480ETMCW-00H(R) BY DATE 2009/08/03 ; Approved For Specifications Approved For Specifications & Sample AMPIRE CO., LTD. 2F., No.88, Sec. 1, Sintai 5th Rd., Sijhih City, Taipei County 221, Taiwan (R.O.C.)台北縣汐止市新台五路一段 88 號 2 樓(東方科學園區 D 棟) TEL:886-2-26967269 , FAX:886-2-26967196 or 26967270 APPROVED BY Date : 2009/08/03 CHECKED BY AMPIRE CO., LTD. ORGANIZED BY 1 RECORD Revision Date Page 2005/07/15 - 2005/07/21 3 2005/11/23 OF REVISION Contents Editor New Release Lee Backlight unit (One CCFL → Two CCFL) 19-20 10. OUTLINE DIMENSION Lee Lee 2006/11/10 4 ABSOLUTE RATINGS ENVIRONMENT 2008/9/17 -- Correction the P/N to AM-640480ETMCW-00H(R) Edward -- New logo and revise the address of company Edward 18 Add guarantee declaration Edward 19-20 Update Outline Dimension Edward 2009/1/8 2009/8/3 3 Date : 2009/08/03 Lee Correction the value of outline dimension Edward AMPIRE CO., LTD. 2 1. Introduction Ampire Display Module AM640480E1TMCW00 is a color active matrix TFT-LCD that uses amorphous silicon TFT as a switching device . This model is composed of a TFT-LCD panel , a driving circuit and a backlight system . This TFT-LCD has a 10.4-inch diagonally measured active display area with VGA resolution(640(R.G.B) X 480) and can display up to 262,144 colors . 1-1. Features - Wide viewing angle. - High contrast radio - High operating temperature - High color saturation 1-2. Applications ● Panel PC ● HMI (Human machine interface) ● Industrial application ● POS 2. Physical specifications Item Specifications unit 640 x RGB (W) x 480(H) dots Active area 211.2 (W) x 158.4 (H) mm Screen size 10.4(Diagonal) inch Pixel pitch 0.33 (W) x 0.33 (H) mm Color configuration R.G.B Vertical stripe Overall dimension 225.5±0.5(W)x176.3±0.5(H)x9.5±0.5(D) mm 440(typ) g Display resolution(dot) Weight Surface treatment Backlight unit Input signal Display color Date : 2009/08/03 Antiglare , Hard-Coating(3H) Two CCFL TTL 262,144 AMPIRE CO., LTD. colors 3 3. ABSOLUTE MAXIMUM RATINGS 3-1. ABSOLUTE RATINGS ENVIRONMENT ITEM CONDITIONS HIGH TEMPERATURE OPERATION HIGH TEMPERATURE AND HIGH HUMIDITY OPERATION HIGH TEMPERATURE STORAGE 70℃ , 240Hrs 60℃ , 90%RH , 240Hrs 80℃ , 240Hrs LOW TEMPERATURE OPERATION -20℃ , 240Hrs LOW TEMPERATURE STORAGE THERMAL SHOCK (Non-operation) SHOCK (Non-Operation) VIBRATION (Non-Operation) ESD (Operation) -20℃ , 240Hrs -20℃(0.5Hr) ~80℃(0.5Hr) 100Cycle ; 1hour/cycle 220G , 2ms , half sine wave 1 time for ±X , ±Y , ±Z , 1.5G , 10~300Hz , 10min/cycle , 3 cycle each X,Y,Z 150Pf , 330Ω, 1sec/cycle 1) ±8kV : panel contact 2) ±15kV : panel non-contact NOTE (1)(2) (2)(3) (2)(3) (2) NOTE : (1) Temperature and relative humidity range is shown in the figure below (a) 90﹪RH Max.(Ta≦40℃) (b) Wet-bulb temperature should be 39℃ Max (Ta＞40℃) (c) No condensation (2) No display malfunctions (3) At testing Vibration and Shock , the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture (4) The temperature of panel display surface area should be 80℃ Max Date : 2009/08/03 AMPIRE CO., LTD. 4 3-2. ELECTRICAL ABSOLUTE RATINGS 3-2-1 TFT LCD MODULE Item Value Symbol Min. Max. Unit Power supply voltage VCC -0.3 6.0 V Logic input voltage VIN -0.3 Vcc+0.3 V Remark (1) 3-2-2 BACKLIGHT UNIT Item Symbol Value Min. Max. Unit Remark (1)(2) IL = 5.5mA Lamp voltage VL - (2.5K) VRMS Lamp current IL - 6 mARMS Lamp frequency FL (1)(2) - 80 KHZ NOTE : (1) Permanent damage to the device may occur if maximum values are exceeded . Function operation should be restricted to the conditions described under Normal operating conditions . (2) Specified values are for lamp (Refer to 3.2 for further IL information) Date : 2009/08/03 AMPIRE CO., LTD. 5 4. Electrical Characteristics Ta = 25 ± 2℃ 4.1 TFT LCD MODULE Item Symbol Min. Typ. Max. Unit VCC (3.0) 3.3 (3.6) V VIH 0.7 VCC - VCC V VIL 0 - 0.3 VCC V IRUSH - - (1) A (2) White IDD 1 - (495) - mA (3)a Black IDD 2 - (450) - mA (3)b Vertical stripe IDD 3 - (563) - mA (3)c Power supply voltage Logic input voltage Rush current Power supply current Remark NOTE : (1) The module should be always operated within above ranges (2) Measurement condition Date : 2009/08/03 AMPIRE CO., LTD. 6 (3) The specified power supply current is under the conditions at VCC = 3.3V , Ta = 25 ± 2 ℃ , fv = 60Hz , whereas a power dissipation check pattern below is displayed. a. White Pattern b. Black Pattern c. Vertical Stripe Pattern Date : 2009/08/03 AMPIRE CO., LTD. 7 4-2 BACKLIGHT UNIT Item Symbol Min. Value Min. Max. Unit Remark Lamp input voltage VL (440) (490) (540) Vrms (1) , IL=(5.5)mA Lamp current IL (2.0) (5.5) (6.0) mArms (1) Lamp Turn on voltage VS - - (770) (960) Vrms Vrms (2) 25℃ (2) 0℃ Operating Frequency FL (40) - (80) KHz (3) Lamp Life Time LBL (50K) - - Hrs (5) Power Consumption PL - (5.39) - W (4), IL=(5.5)mA Note : (1) IL means the lamp current of one lamp. (2) The voltage shown above should be applied to the lamp for more than 1 second after startup . Otherwise the lamp may not be turned on . (3) The lamp frequeny may produce interference with horizontal synchronous frequency from the display , and this may cause line flow on the display . In order to avoid interference , the lamp frequency should be detached from the horizontal synchronous frequency and its harmonics as far as possible. (4) PL = IL x VL x 2 (5) The lifetime of lamp can be defined as the time in which it continues to operate under the condition Ta = 25±2℃ and IL =(5.5)mArms until one of the following events occurs. (a) When the brightness becomes or lower than 50% of its original value. (b) When the effective ignition length becomes or lower than 80% of its original value.(Effective ignition length is defined as an area that has less than 70% brightness compared to the brightness in the center point.) Date : 2009/08/03 AMPIRE CO., LTD. 8 5. BLOCK DIAGRAM 5-1 TFT LCD MODULE 5-2 BACKLIGHT UNIT Date : 2009/08/03 AMPIRE CO., LTD. 9 6. INPUT TERMINAL PIN ASSIGNMENT 6-1 TFT LCD MODULE Pin no 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Symbol GND DCLK HS VS GND R0 R1 R2 R3 R4 R5 GND G0 G1 G2 G3 G4 G5 GND B0 B1 B2 B3 B4 B5 GND DE Vcc Vcc N.C. DPSR Function Ground Dot clock Horizontal synchronous Vertical synchronous Ground Red data (LSB) Red data Red data Red data Red data Red data (MSB) Ground Green data (LSB) Green data Green data Green data Green data Green data (MSB) Ground Blue data (LSB) Blue data Blue data Blue data Blue data Blue data (MSB) Ground Data enable signal Power supply Power supply Reserved , please keep it floating Selection of scan direction Note : Connector Part No. : DF 9C-31P-1V or equivalent. 6-2 SCANNING DIRECTION The following figures are seen from a front view and the arrow shows the direction of scan. Figure1. Normal scan( DPSR : Low or Open ) Date : 2009/08/03 Figure2. Reverse scan( DPSR : High ) AMPIRE CO., LTD. 10 6-3 BACKLIGHT UNIT Pin 1 2 3 Symbol GND HV1 HV2 Description Ground High voltage High voltage Remark White Pink Pink NOTE : Connector Part No : BHR-03VS-1 (J.S.T Mfg,Co,Ltd) 6-4 COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red,green and blue) is based on the 6-bit gray scale data input for the color. The higher the binary input , the bright the color. The table below provides the assignment of color versus data input. NOTE : 0 → Low Level Voltage , 1 → High Level Voltage Date : 2009/08/03 AMPIRE CO., LTD. 11 7. INPUT TIMING 7-1 INPUT SIGNAL TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. Signal Item Symbol Min. Typ. Max. Unit Note Dot Clock Dot Data Frequency Fc Duty 21 25.175 29 0.4 0.5 0.6 MHz - Setup Time Tlvs (8) - - ns - Hold Time Tlvh (12) - - ns - Fr 56 60 75 Hz Tv=Tvd+Tvb Tv (690) 800 (1279) Th - Tvd 640 640 640 Th - Tvb (50) 160 Tv-Tvd Th - Th (482) 525 (959) Tc Th=Thd+Thb Thd 480 480 480 Tc - Thb (2) 45 Th-Thd Tc - Frame Rate Vertical Active Total Display Term Display Blank Total Horizontal Active Display Display Term Blank INPUT SIGNAL TIMING DIAGRAM Date : 2009/08/03 AMPIRE CO., LTD. 12 7-2 POWER ON/OFF SEQUENCE To prevent a latch-up or DC o[eration or LCD module, the power on/off sequence should be as the diagram below. Timing Specifications : 0.5 ＜ t1 ≦ 10ms 0 ＜ t2 ≦ 50ms 0 ＜ t3 ≦ 50ms t4 ≧ 500ms t5 ≧ 200ms t6 ≧ 200ms NOTE : (1) Please avoid floating state of interface signal at invalid period. (2) When the interface signal is invalid, be sure to pull down the power supply of LCD Vcc to 0V. (3) The Backlight inverter power must be turned on after the power supply for the logic and the interface signal is valid. The Backlight inverter power must be turned off before the power supply for the logic and the interface signal is invalid. Date : 2009/08/03 AMPIRE CO., LTD. 13 8. OPTICAL SPECIFICATIONS 8-1 TEST CONDITIONS Item Symbol Value Unit Ambient Temperature Ta 25±2 ℃ Ambient Humidity Ha 50±10 %RH Supply Voltage Vcc (3.3) V Input Signal According to typical value in “4. Electrical Characteristics Lamp Current IL (5.5) mARMS Inverter Frequency FL (60) KHz Inverter (Sumida IV40090T/B2) NOTE : IL means the lamp current of one lamp. 8-2 OPTICAL SPECIFICATIONS The relative measurement methods of optical characteristics are shown in 8-2. The following items should be measured under the test conditions described in 8-1 and stable environment shown in Note (6) Item Response time Symbol Rise TR Fall TF Contrast ratio Viewing angle CR ΘX=0° ΘY=0° Min. Typ. Max. - (14) (19) - (9) (14) (500) (750) - (80) (85) - (80) (85) - (80) (85) - Unit Remark ms (1) - (2)(6) Deg. (3) Top ΘY+ Bottom ΘY- Left ΘX- Right ΘX+ (80) (85) - LC (320) (380) - cd/m2 (4)(6) δW - - (1.4) - (5) Center Luminance of White White Variation Red Color chromaticity Conditon Green Blue White Date : 2009/08/03 Rx Ry Gx Gy Bx By Wx Wy CR≧10 (0.628) ΘX=0° ΘY=0° (0.347) (0.292) Typ 0.03 AMPIRE CO., LTD. (0.567) (0.144) Typ + 0.03 (3)(6) (0.084) 0.313 0.329 14 NOTE (1) Definition of Response Time (TR , TF)and measurement method : NOTE (2) Definition of Contrast Ratio (CR) : The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L63 / L0 L63 : Luminance of gray level 63 L0 : Luminance of gray level 0 NOTE (3) Definition of Viewing Angle (ΘX , ΘY) : Date : 2009/08/03 AMPIRE CO., LTD. 15 NOTE (4) Definition of Luminance of White( LC ) : Measure the luminance of gray level 63 at center point LC = L(5) ; L(X) is corresponding to the luminance of the point X at Figure in Note(5) NOTE (5) Definition of White Variation ( δW ) : Measure the luminance of gray level 63 at center point δW = Max[L(1), L(2), L(3), L(4), L(5)] / Min[L(1), L(2), L(3), L(4), L(5)] NOTE (6) Measurement Setup The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 20 minutes in a windless room. Date : 2009/08/03 AMPIRE CO., LTD. 16 9. USE PRECAUTIONS 9-1 Handling precautions (1) The polarizing plate may break easily so be careful when handling it. Do not touch, press or rub it with a hard-material tool like tweezers. (2) Do not touch the polarizing plate surface with bare hands so as not to make it dirty. If the surface or other related part of the polarizing plate is dirty, soak a soft cotton cloth or chamois leather in benzine and wipe off with it. Do not use chemical liquids such as acetone, toluene and isopropyl alcohol. Failure to do so may bring chemical reaction phenomena and deteriorations. (3) Remove any spit or water immediately. If it is left for hours, the suffered part may deform or decolorize. (4) If the LCD element breaks and any LC stuff leaks, do not suck or lick it. Also if LC stuff is stuck on your skin or clothing, wash thoroughly with soap and water immediately. 9-2 Installing precautions (1) The PCB has many ICs that may be damaged easily by static electricity. To prevent breaking by static electricity from the human body and clothing, earth the human body properly using the high resistance and discharge static electricity during the operation. In this case, however, the resistance value should be approx. 1MΩ and the resistance should be placed near the human body rather than the ground surface. When the indoor space is dry, static electricity may occur easily so be careful. We recommend the indoor space should be kept with humidity of 60% or more. When a soldering iron or other similar tool is used for assembly, be sure to earth it. (2) When installing the module and ICs, do not bend or twist them. Failure to do so may crack LC element and cause circuit failure. (3)To protect LC element, especially polarizing plate, use a transparent protective plate (e.g., acrylic plate, glass etc) for the product case. (4) Do not use an adhesive like a both-side adhesive tape to make LCD surface (polarizing plate) and product case stick together. Failure to do so may cause the polarizing plate to peel off 9-3 Storage precautions (1) Avoid a high temperature and humidity area. Keep the temperature between 0°C and 35°C and also the humidity under 60%. (2) Choose the dark spaces where the product is not exposed to direct sunlight or fluorescent light. (3) Store the products as they are put in the boxes provided from us or in the same conditions as we recommend. Date : 2009/08/03 AMPIRE CO., LTD. 17 9-4 Operating precautions (1) Do not boost the applied drive voltage abnormally. Failure to do so may break ICs. When applying power voltage, check the electrical features beforehand and be careful. Always turn off the power to the LC module controller before removing or inserting the LC module input connector. If the input connector is removed or inserted while the power is turned on, the LC module internal circuit may break. (2) The display response may be late if the operating temperature is under the normal standard, and the display may be out of order if it is above the normal standard. But this is not a failure; this will be restored if it is within the normal standard. (3) The LCD contrast varies depending on the visual angle, ambient temperature, power voltage etc. Obtain the optimum contrast by adjusting the LC dive voltage. (4) When carrying out the test, do not take the module out of the low-temperature space suddenly. Failure to do so will cause the module condensing, leading to malfunctions. (5) Make certain that each signal noise level is within the standard (L level: 0.2Vdd or less and H level: 0.8Vdd or more) even if the module has functioned properly. If it is beyond the standard, the module may often malfunction. In addition, always connect the module when making noise level measurements. (6) The CMOS ICs are incorporated in the module and the pull-up and pull-down function is not adopted for the input so avoid putting the input signal open while the power is ON. (7) The characteristic of the semiconductor element changes when it is exposed to light emissions, therefore ICs on the LCD may malfunction if they receive light emissions. To prevent these malfunctions, design and assemble ICs so that they are shielded from light emissions. (8) Crosstalk occurs because of characteristics of the LCD. In general, crosstalk occurs when the regularized display is maintained. Also, crosstalk is affected by the LC drive voltage. Design the contents of the display, considering crosstalk. 9-5 Other (1) Do not disassemble or take the LC module into pieces. The LC modules once disassembled or taken into pieces are not the guarantee articles. (2) The residual image may exist if the same display pattern is shown for hours. This residual image, however, disappears when another display pattern is shown or the drive is interrupted and left for a while. But this is not a problem on reliability. (3) AMIPRE will provide one year warrantee for all products and three months warrantee for all repairing products. Date : 2009/08/03 AMPIRE CO., LTD. 18 試用機種: 10. OUTLINE DIMENSION Date : 2009/08/03 AMPIRE CO., LTD. 19 試用機種: Date : 2009/08/03 AMPIRE CO., LTD. 20