Product Family Datasheet - Cld

www.osram.com
OSRAM
Value Flex Power – VF06P
Data Sheet
Benefits
Energy saving low-power LED flexible strip for
hospitality and general lighting.
Self-adhesive tape on the back for easy and fast
installation.
Consistent colour provides fine and comfort light
output.
Applications
Hospitality lighting for hotels, commercial
buildings and retail shops.
Cove lighting for hotel lobby, guest rooms,
function rooms, commercial building lobby,
hospitals, libraries and offices.
Technical Operating Data
Current Radiance
Angle
[A]*
[°]*
Wavelength
Color Temp
Product
Color
No. of
LEDs
Voltage
[V DC]*
Power
[W]*
VF06P-W4F-727
White
270
24
62
2.48
120
2700 K
VF06P-W4F-730
White
270
24
62
2.48
120
3000 K
4250
VF06P-W4F-740
White
270
24
62
2.48
120
4000 K
4250
VF06P-W4F-765
White
270
24
62
2.48
120
6500 K
4750
[K]*
Lum. Flux
[lm]*
4250
*) All Data are related to the entire module.
Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not
necessarily correspond to the actual parameters of each single product which could differ from the typical data.
Technical Features
Size of printed circuit board (L x W x H):
Linear LED strip on flexible printed circuit board with
self-adhesive tape at the back allow for easy mounting
5000 mm x 8 mm x 1.5 mm
Up to 25,000 h lifetime for Ta = 25 oC.
Size of smallest unit (L x W):
Accessory: Value Flex Track in 150mm and 1000mm
are available for mounting use.
111 mm x 8 mm
The maximum LED pitch is 18.5mm
Entire Module consists of 270 LEDs
Connection possible at the reel end or at the cut points
VF06P– V1. 21.01.2013
Page 1 of 4
www.osram.com
OSRAM
Minimum / Maximum Ratings
Operating Temperature
at Tc-Point [°C]*
Storage
Temperature [°C]*
Voltage Range
[V dc]*
Reverse Voltage
[V dc]*
VF06P-W4F-727
-10 … 60
-20 … 65
23 … 25
25
VF06P-W4F-730
-10 … 60
-20 … 65
23 … 25
25
VF06P-W4F-740
-10 … 60
-20 … 65
23 … 25
25
VF06P-W4F-765
-10 … 60
-20 … 65
23 … 25
25
Product
*) Exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the LED Modules.
Exceeding maximum ratings for operating voltage will cause hazardous overload and will likely destroy the LED Modules.
The temperature of the LED modules must be measured at the Tc-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature
sensitive label.
Dimensions
Value Flex Power
SCALE 5:1
Accessory
Value Flex Track 150mm/1000mm
VF06P– V1. 21.01.2013
Page 2 of 4
www.osram.com
OSRAM
Safety Information
The LED module itself and all its components must not be mechanically stressed.
Assembly must not damage or destroy conducting paths on the circuit board.
To avoid mechanical damage, the LED modules should be attached securely to the intended substrate. Heavy vibration
should be avoided.
The LED module incorporates no protection against short circuits, overload or overheating.
In order to drive OSRAM LED-Modules safely, it is absolutely necessary to operate them with an electronically
stabilized power supply protecting against short circuits, overload and overheating.
For dimming applications attention should be paid to specific references in “OPTOTRONIC ® Technical Guide”.
To also ease the luminaire/installation approval, electronic control gear for LED or LED modules must carry the CE mark.
In Europe the declarations of conformity must include the following standards:
CE: EN 61347-2-13, EN 55015, EN 61547 and EN 61000-3-2.
Also check for the mark of an independent authorized certification institute.
Please see the relevant application guides for more detailed information.
When using power supplies other than OPTOTRONIC ® the following basic safety features are required, in addition to any
other application specific concerns and local safety codes.
OSRAM OPTOTRONIC® electronic control gear complies to all relevant standards and guarantees safe operation.
Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety
standards. Only qualified personnel should be allowed to perform installations.
Observe correct polarity! Incorrect polarity will lead to no light emission.
Parallel connection is highly recommended as safe electrical operation mode. Serial connection is not recommended.
Unbalanced voltage drop can cause hazardous overload and damage the LED module.
The maximum length of VF06P is 5M (62W version) with power feed at one end.
OTe 90/220-240/24 E can contact 1 reel of VF06P in parallel, power feed at the end of the flex.
When mounting on metallic or otherwise conductive surfaces, there needs to be a electrical isolation at soldering points
between module and the mounting surface,
Pay attention to ESD steps when mounting the module.
Please ensure that the power supply is of adequate power to operate the total load.
LED modules are dimmable by means of PWM (pulse width modulation). It is recommended using the following OSRAM
control gears: OPTOTRONIC® OT DIM, OT DALI DIM, OT DALI DIM LI.
The LED module must not be operated in places which are directly exposed to water or moisture, as it is for indoor
applications.
Damage by corrosion will not be honored as a materials defect claim. It is the user’s responsibility to provide suitable
protection against corrosive agents such as moisture and condensation and other harmful elements.
For applications involving exposure to humidity and dust the module must be protected by a fixture or housing with a
suitable protection class.
VF06P– V1. 21.01.2013
Page 3 of 4
www.osram.com
OSRAM
Assembly Information
Connection with soldering wires on unmounted module: Do not pre-tin the solder pads but pre-tin the wires and solder for
max 4s at 300 oC. Allow solder points to completely cool down before the next soldering. Prevent shear- or peel forces.
Soldering of wires with the module mounted on a heat sink: Pre-tin solder pads and wires and solder for max 3s at 350 oC.
Allow solder points to completely cool down before the next soldering. Prevent shear- or peel forces.
The smallest unit (111 mm – 6 LEDs) can be removed by cutting with scissors between the designated solder pads.
The mounting of the module is facilitated by means of the double-sided adhesive on the back-surface of the module. Care
must be taken to provide a clean and dry mounting surface, free of oils or silicone coatings as well as dirt particle. The
mounting substrate must have sufficient structural integrity. Take care to completely remove the protective backing. Once
the module is appropriately positioned, press on the module with about 20N/cm2 (refer to application techniques of 3M
adhesive transfer tapes). In difficult cases the use of a primer may help.
The minimum bending radius is 5cm.
Ordering Guide
Product group
Product name
EAN 40*
S-Unit*
Value Flex Power 2700K
VF06P-W4F-727
4008321866721
8 pcs
Value Flex Power 3000K
VF06P-W4F-730
4008321866905
8 pcs
Value Flex Power 4000K
VF06P-W4F-740
4008321867148
8 pcs
Value Flex Power 6500K
VF06P-W4F-765
4008321867322
8 pcs
Value Flex Track 150mm
VF-TR150
4008321867674
20 pcs
Value Flex Track 1000mm
VF-TR1000
4008321867643
20 pcs
* EAN: Ordering number per single sale unit
* S-Unit: Modules / accessory number per shipping unit
Note: Typical performance data are subject to change without any further notice, particularly as LED technology evolves.
Sales and Technical Support
OSRAM Asia Pacific
Sales and technical support is given by the
local OSRAM subsidiaries.
On our world wide homepage all OSRAM
subsidiaries are listed with complete address
and phone numbers.
30th Floor, China Resources Building
26 Harbour Road, WanChai, Hong Kong
www.osram.com
VF06P– V1. 21.01.2013
Page 4 of 4