RFM products are now Murata products. SF1056A • • • • • • Designed for DECT and WLAN IF Applications Low Insertion Loss Excellent Size-to-Performance Ratio Hermetic 13.3 X 6.5 mm Surface-Mount Case Unbalanced Input and Output Complies with Directive 2002/95/EC (RoHS) 110.592 MHz SAW Filter Pb Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +10 dBm Max. DC voltage between any 2 terminals 30 VDC Storage Temperature Range -40 to +85 Suitable for lead-free soldering - Max Soldering Profile °C 260°C for 30 s SM13365-12 Electrical Characteristics Characteristic Sym Nominal Center Frequency fC Passband Insertion Loss at fc Rejection Notes Min 1 IL 3 dB Passband BW3 Group Delay Variation over fc ±576 kHz GDV 1, 2 8.5 ±576 1, 2, 3 28 40 40 >45 Ultimate Units MHz 10.0 dB kHz 200 nsP-P dB 45 TA Operating Temperature Range Max ±750 <150 fc-3.4 to fc-1.728 and fc+1.728 to fc+3.4 MHz DC to fc-3.4 and fc+3.4 to 200 MHz Typ 110.592 1 +60 -10 Impedance Matching to 50 Ω unbalanced °C External L-C Case Style SM13365-12 13.3 X 6.5 mm Nominal Footprint Lid Symbolization (YY=year, WW=week) See note 4 RFM SF1056A YYWW Electrical Connections Connection Terminals Port 1Hot 2 Port 1 Gnd Return 3 Port 2 Hot 8 Port 2 Gnd Return 9 Case Ground All Others CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. NOTES: 1. 2. 3. 4. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." ©2010-2014 by Murata Electronics N.A., Inc. SF1056A (R) 3/18/14 5. 6. 7. 8. Page 1 of 4 The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd. www.murata.com ©2010-2014 by Murata Electronics N.A., Inc. SF1056A (R) 3/18/14 Page 2 of 4 www.murata.com Tape and Reel Specifications 100 Min 254 "B" REF. 100 REF. Quantity Per Reel 1000 Max See Detail "A" 13. 0 12.0 24.4 20 21.0 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao 7.0 mm Bo 13.8 mm Ko 2.0 mm Pitch 12.0 mm W 24.0 mm PIN #1 USER DIRECTION OF FEED ©2010-2014 by Murata Electronics N.A., Inc. SF1056A (R) 3/18/14 Page 3 of 4 www.murata.com SM13365-12 Case 12-Terminal Ceramic Surface-Mount Case 13.3 x 6.5 mm Nominal Footprint Case Dimensions mm Dimension A B C D E H P Min Nom Max Min Nom Max 13.08 6.27 13.31 6.50 1.91 1.50 0.79 1.0 2.54 13.60 6.80 2.00 0.515 0.247 0.524 0.256 0.075 0.059 0.031 0.039 0.100 0.535 0.268 0.079 Electrical Connections Materials Solder Pad Termination Au plating 30 - 60 µinches (76.2-152 µm) over 80-200 µinches (203-508 µm) Ni. Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phosphorus) 100-200 µinches Thick Body Inches Connection Port 1 Port 2 Al2O3 Ceramic Terminals Input or Return 2 Return or Input 3 Output or Return 8 Return or Output Pb Free 9 Ground All others Single Ended Operation Return is ground Differential Operation C B 3 Return is hot 4 D H 2 1 2 3 4 1 P (8 Places) 5 12 12 5 6 11 11 6 7 10 10 7 A 8 9 9 8 BOTTOM VIEW TOP VIEW ©2010-2014 by Murata Electronics N.A., Inc. SF1056A (R) 3/18/14 E (10 Places) Page 4 of 4 www.murata.com