MT9094AP1 - Microsemi

ISO2-CMOS ST-BUSTM FAMILY MT9094
Digital Telephone (DPhone-II)
Data Sheet
Features
February 2005
•
Programmable µ-Law/A-Law codec and filters
•
Programmable CCITT (G.711)/sign-magnitude
coding
•
Programmable transmit, receive and side-tone
gains
•
DSP-based:
Ordering Information
MT9094AP
MT9094APR
MT9094AP1
MT9094APR1
Speakerphone switching algorithm
•
DTMF and single tone generator
•
Tone Ringer
Description
•
Differential interface to telephony transducers
•
Differential audio paths
•
Single 5 volt power supply
The MT9094 DPhone-II is a fully featured integrated
digital telephone circuit. Voice band signals are
converted to digital PCM and vice versa by a switched
capacitor Filter/Codec. The Filter/Codec uses an
ingenious differential architecture to achieve low noise
operation over a wide dynamic range with a single 5 V
supply. A Digital Signal Processor provides handsfree
speaker-phone operation. The DSP is also used to
generate tones (DTMF, Ringer and Call Progress) and
control audio gains. Internal registers are accessed
through a serial microport conforming to INTEL MCS51™ specifications. The device is fabricated in
Zarlink's low power ISO2-CMOS technology.
Applications
•
Fully featured digital telephone sets
•
Cellular phone sets
•
Local area communications stations
Digital Signal Processor
DSTi
Filter/Codec Gain
ENCODER
22.5/-72dB
∆1.5dB
Tx & Rx
DECODER
MIC-
7dB
MIC+
Transducer
Interface
-7dB
M-
F0i
M+
C4i
VSSD
Tubes
Tape & Reel
Tubes
Tape & Reel
-40°C to +85°C
•
DSTo
44 Pin PLCC
44 Pin PLCC
44 Pin PLCC*
44 Pin PLCC*
*Pb Free Matte
HSPKR+
STATUS
Control
Registers
C-Channel
Registers
HSPKRSPKR+
VDD
SPKR-
VSSA
VSS
SPKR
New Call
Tone
Generator
Timing
Circuits
VBias
VRef
S/P &
P/S
Converter
LCD Driver
S1
S12
BP
WD PWRST
Serial
Port
(MCS-51
Compatible)
IC
Figure 1 - Functional Block Diagram
1
Zarlink Semiconductor Inc.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright 1995-2005, Zarlink Semiconductor Inc. All Rights Reserved.
DATA 2
DATA 1
SCLK
CS
MT9094
6
5
4
3
2
1
44
43
42
41
40
PWRST
IC
VRef
VBias
NC
M+
MVSSA
MIC+
MICVSS SPKR
Data Sheet
7
8
9
10
11
12
13
14
15
16
17
39
38
37
36
35
34
33
32
31
30
29
SPKR+
SPKRHSPKR+
HSPKRVDD
BP
S12
S11
S10
S9
S8
IC
NC
NC
VSSD
S1
S2
S3
S4
S5
S6
S7
18
19
20
21
22
23
24
25
26
27
28
DSTi
DSTo
C4i
F0i
VSSD
NC
SCLK
DATA 2
DATA 1
CS
WD
44 PIN PLCC
Figure 2 - Pin Connections
Pin Description
Pin #
Name
1
M+
Non-Inverting Microphone (Input). Non-inverting input to microphone amplifier from the handset
microphone.
2
NC
No Connect. No internal connection to this pin.
3
VBias
Bias Voltage (Output). (VDD/2) volts is available at this pin for biasing external amplifiers. Connect 0.1
µF capacitor to VSSA.
4
VRef
Reference voltage for codec (Output). Nominally [(VDD/2)-1.5] volts. Used internally. Connect 0.1 µF
capacitor to VSSA.
5
IC
6
Description
Internal Connection. Tie externally to VSS for normal operation.
PWRST Power-up Reset (Input). CMOS compatible input with Schmitt Trigger (active low).
7
DSTi
ST-BUS Serial Stream (Input). 2048 kbit/s input stream composed of 32 eight bit channels; the first
four of which are used by the MT9094. Input level is TTL compatible.
8
DSTo
ST-BUS Serial Stream (Output). 2048 kbit/s output stream composed of 32 eight bit channels. The
MT9094 sources digital signals during the appropriate channel, time coincident with the channels used
for DSTi.
9
C4i
4096 kHz Clock (Input). CMOS level compatible.
10
F0i
Frame Pulse (Input). CMOS level compatible. This input is the frame synchronization pulse for the
2048 kbit/s ST-BUS stream.
11
VSSD
12
NC
Digital Ground. Nominally 0 volts.
No Connect. No internal connection to this pin.
2
Zarlink Semiconductor Inc.
MT9094
Data Sheet
Pin Description (continued)
Pin #
Name
13
SCLK
Description
Serial Port Synchronous Clock (Input). Data clock for MCS-51 compatible microport. TTL level
compatible.
14
DATA 2 Serial Data Transmit. In an alternate mode of operation, this pin is used for data transmit from MT9094.
In the default mode, serial data transmit and receive are performed on the DATA 1 pin and DATA 2 is tristated.
15
DATA 1 Bidirectional Serial Data. Port for microprocessor serial data transfer compatible with MCS-51 standard
(default mode). In an alternate mode of operation, this pin becomes the data receive pin only and data
transmit is performed on the DATA 2 pin. Input level TTL compatible.
16
CS
Chip Select (Input). This input signal is used to select the device for microport data transfers. Active
low. (TTL level compatible.)
17
WD
Watchdog (Output). Watchdog timer output. Active high.
18
IC
Internal Connection. Tie externally to VSS for normal operation.
19,
20
NC
No Connection. No internal connection to these pins.
21
VSSD
22-33
S1-S12
34
BP
Backplane Drive (Output). A two-level output voltage for biasing an LCD backplane.
35
VDD
Positive Power Supply (Input). Nominally 5 volts.
Digital Ground. Nominally 0 volts.
Segment Drivers (Output). 12 independently controlled, two level, LCD segment drivers. An in-phase
signal, with respect to the BP pin, produces a non-energized LCD segment. An out-of-phase signal, with
respect to the BP pin, energizes its respective LCD segment.
36
HSPKR- Inverting Handset Speaker (Output). Output to the handset speaker (balanced).
37
HSPKR+ Non-Inverting Handset Speaker (Output). Output to the handset speaker (balanced).
38
SPKR-
Inverting Speaker (Output). Output to the speakerphone speaker (balanced).
39
SPKR+ Non-Inverting Speaker (Output). Output to the speakerphone speaker (balanced).
40
VSS
SPKR
Power Supply Rail for Analog Output Drivers. Nominally 0 Volts.
41
MIC-
Inverting Handsfree Microphone (Input). Handsfree microphone amplifier inverting input pin.
42
MIC+
Non-inverting Handsfree Microphone (Input). Handsfree microphone amplifier non-inverting input
pin.
43
VSSA
Analog Ground. Nominally 0 V.
44
M-
Inverting Microphone (Input). Inverting input to microphone amplifier from the handset microphone.
NOTES:
Intel and MCS-51 are registered trademarks of Intel Corporation, Santa Clara, CA, USA.
Overview
The Functional Block Diagram of Figure 1 depicts the main operations performed within the DPhone-II. Each of
these functional blocks will be described in the sections to follow. This overview will describe some of the end-user
features which may be implemented as a direct result of the level of integration found within the DPhone-II.
3
Zarlink Semiconductor Inc.
MT9094
Data Sheet
The main feature required of a digital telephone is to convert the digital Pulse Code Modulated (PCM) information,
being received by the telephone set, into an analog electrical signal. This signal is then applied to an appropriate
audio transducer such that the information is finally converted into intelligible acoustic energy. The same is true of
the reverse direction where acoustic energy is converted first into an electrical analog and then digitized (into PCM)
before being transmitted from the set. Along the way if the signals can be manipulated, either in the analog or the
digital domains, other features such as gain control, signal generation and filtering may be added. More complex
processing of the digital signal is also possible and is limited only be the processing power available. One example
of this processing power may be the inclusion of a complex handsfree switching algorithm. Finally, most electroacoustic transducers (loudspeakers) require a large amount of power to develop an effective acoustic signal. The
inclusion of audio amplifiers to provide this power is required.
The DPhone-II features Digital Signal Processing (DSP) of the voice encoded PCM, complete Analog/Digital and
Digital/Analog conversion of audio signals (Filter/CODEC) and an analog interface to the external world of electroacoustic devices (Transducer Interface). These three functional blocks combine to provide a standard full-duplex
telephone conversation utilizing a common handset. Selecting transducers for handsfree operation, as well as
allowing the DSP to perform its handsfree switching algorithm, is all that is required to convert the full-duplex
handset conversation into a half-duplex speakerphone conversation. In each of these modes, full programmability
of the receive path and side-tone gains is available to set comfortable listening levels for the user as well as
transmit path gain control for setting nominal transmit levels into the network.
The ability to generate tones locally provides the designer with a familiar method of feedback to the telephone user
as they proceed to set-up, and ultimately, dismantle a telephone conversation. Also, as the network slowly evolves
from the dial pulse/DTMF methods to the D-Channel protocols it is essential that the older methods be available for
backward compatibility. As an example; once a call has been established, say from your office to your home, using
the D-Channel signalling protocol it may be necessary to use in-band DTMF signalling to manipulate your personal
answering machine in order to retrieve messages. Thus the locally generated tones must be of network quality and
not just a reasonable facsimile. The DPhone-II DSP can generate the required tone pairs as well as single tones to
accommodate any in-band signalling requirement.
Each of the programmable parameters within the functional blocks is accessed through a serial microcontroller port
compatible with Intel MCS-51 specifications.
Functional Description
In this section, each functional block within the DPhone-II is described along with all of the associated
control/status bits. Each time a control/ status bit(s) is described it is followed by the address register where it will be
found. The reader is referred to the section titled ‘Register Summary' for a complete listing of all address map
registers, the control/status bits associated with each register and a definition of the function of each control/status
bit. The Register Summary is useful for future reference of control/status bits without the need to locate them within
the text of the functional descriptions.
Filter-CODEC
The Filter/CODEC block implements conversion of the analog 3.3kHz speech signals to/from the digital domain
compatible with 64 kb/s PCM B-Channels. Selection of companding curves and digital code assignment are
register programmable. These are CCITT G.711 A-law or µ-Law, with true-sign/ Alternate Digit Inversion or truesign/Inverted Magnitude coding, respectively. Optionally, sign- magnitude coding may also be selected for
proprietary applications.
The Filter/CODEC block also implements transmit and receive audio path gains in the analog domain. These gains
are in addition to the digital gain pad provided in the DSP section and provide an overall path gain resolution of
0.5 dB. A programmable gain, voice side-tone path is also included to provide proportional transmit speech
feedback to the handset receiver so that a dead sounding handset is not encountered. Figure 3 depicts the nominal
half-channel and side-tone gains for the DPhone-II.
4
Zarlink Semiconductor Inc.
MT9094
SERIAL
PORT
DSP GAIN*
Data Sheet
TRANSDUCER INTERFACE
FILTER/CODEC
µ-Law –6.3 dB
Α-Law –3.7 dB
Receiver
Driver
Receive
PCM
–72 to
+22.5 dB
(1.5dB
steps)
DTMF,
Tone
Ringer &
Handsfree
-6 dB
Receive
Filter Gain
0 to –7 dB
(1 dB steps)
Handset
Receiver
(150Ω)
-6 dB
HSPKR+
75
HSPKR–
75
Speaker
Phone
Driver
0.2dB*
Side-tone
–9.96 to
+9.96dB
(3.32 dB steps)
Speaker Gain
0 to –24 dB
(8 dB steps)
SPKR+
SPKR–
Speakerphone
Speaker
(40Ω nominal)
(32Ω min)
Tone
Ringer
(input
from DSP)
Side-tone
Nominal
Gain
µ-Law –11 dB
Α-Law –18.8 dB
PCM
–72 to
+22.5 dB
(1.5dB
steps)
Transmit
Filter Gain
0 to +7dB
(1 dB steps)
µ-Law 6.1dB
Α-Law 15.4dB
Transmit
DIGITAL DOMAIN
Transmit
Gain
M
U
X
MIC+ Handsfree
MIC– mic
M+
M–
Transmitter
microphone
ANALOG DOMAIN
Internal to Device
External to Device
Note: *gain the same for A-Law and m−Law
Figure 3 - Audio Gain Partitioning
On PWRST (pin 6) the Filter/CODEC defaults such that the side-tone path, dial tone filter and 400 Hz transmit filter
are off, all programmable gains are set to 0 dB and µ-Law companding is selected. Further, the Filter/CODEC is
powered down due to the PuFC bit (Transducer Control Register, address 0Eh) being reset. This bit must be set
high to enable the Filter/CODEC.
The internal architecture is fully differential to provide the best possible noise rejection as well as to allow a wide
dynamic range from a single 5 volt supply design. This fully differential architecture is continued into the Transducer
Interface section to provide full chip realization of these capabilities.
A reference voltage (VRef), for the conversion requirements of the CODER section, and a bias voltage (VBias), for
biasing the internal analog sections, are both generated on-chip. VBias is also brought to an external pin so that it
may be used for biasing any external gain plan setting amplifiers. A 0.1 µF capacitor must be connected from VBias
to analog ground at all times. Likewise, although VRef may only be used internally, a 0.1 µF capacitor from the VRef
5
Zarlink Semiconductor Inc.
MT9094
Data Sheet
pin to ground is required at all times. It is suggested that the analog ground reference point for these two capacitors
be physically the same point. To facilitate this the VRef and VBias pins are situated on adjacent pins.
The transmit filter is designed to meet CCITT G.714 specifications. The nominal gain for this filter path is 0 dB (gain
control = 0 dB). An anti-aliasing filter is included. This is a second order lowpass implementation with a corner
frequency at 25 kHz. Attenuation is better than 32 dB at 256 kHz and less than 0.01 dB within the passband.
An optional 400 Hz high-pass function may be included into the transmit path by enabling the Tfhp bit in the
Transducer Control Register (address 0Eh). This option allows the reduction of transmitted background noise such
as motor and fan noise.
The receive filter is designed to meet CCITT G.714 specifications. The nominal gain for this filter path is 0 dB (gain
control = 0 dB). Filter response is peaked to compensate for the sinx/x attenuation caused by the 8 kHz sampling
rate.
The Rx filter function can be altered by enabling the DIAL EN control bit in the Transducer Control Register
(address 0Eh). This causes another lowpass function to be added, with a 3 dB point at 1000 Hz. This function is
intended to improve the sound quality of digitally generated dial tone received as PCM.
Transmit sidetone is derived from the Tx filter and is subject to the gain control of the Tx filter section. Sidetone is
summed into the receive path after the Rx filter gain control section so that Rx gain adjustment will not affect
sidetone levels. The side-tone path may be enabled/disabled with the SIDE EN bit located in the Transducer
Control Register (address 0Eh). See also STG0-STG2 (address 0Bh).
Transmit and receive filter gains are controlled by the TxFG0-TxFG2 and RxFG0-RxFG2 control bits respectively.
These are located in the FCODEC Gain Control Register 1 (address 0Ah). Transmit filter gain is adjustable from
0 dB to +7 dB and receive filter gain from 0 dB to -7 dB, both in 1 dB increments.
Side-tone filter gain is controlled by the STG0-STG2 control bits located in the FCODEC Gain Control Register 2
(address 0Bh). Side-tone gain is adjustable from -9.96 dB to +9.96 dB in 3.32 dB increments.
Law selection for the Filter/CODEC is provided by the A/µ companding control bit while the coding scheme is
controlled by the sign-mag/CCITT bit. Both of these reside in the General Control Register (address 0Fh).
Digital Signal Processor
The DSP block is located, functionally, between the serial ST-BUS port and the Filter/CODEC block. Its main
purpose is to provide both a digital gain control and a half-duplex handsfree switching function. The DSP will also
generate the digital patterns required to produce standard DTMF signalling tones as well as single tones and a tone
ringer output. A programmable (ON/OFF) offset null routine may also be performed on the transmit PCM data
stream. The DSP can generate a ringer tone to be applied to the speakerphone speaker during normal handset
operation so that the existing call is not interrupted.
The main functional control of the DSP is through two hardware registers which are accessible at any time via the
microport. These are the Receive Gain Control Register at address 1Dh and the DSP Control Register at address
1Eh. In addition, other functional control is accomplished via multiple RAM-based registers which are accessible
only while the DSP is held in a reset state. This is accomplished with the DRESET bit of the DSP Control Register.
Ram-based registers are used to store transmit gain levels (20h for transmit PCM and 21h for transmit DTMF
levels), the coefficients for tone and ringer generation (addresses 23h and 24h), and tone ringer warble rates
(address 26h). All undefined addresses below 20h are reserved for the temporary storage of interim variables
calculated during the execution of the DSP algorithms. These undefined addresses should not be written to via the
microprocessor port. The DSP can be programmed to execute the following micro-programs which are stored in
instruction ROM, (see PS0 to PS2, DSP Control Register, address 1Eh). All program execution begins at the frame
pulse boundary.
PS2
0
PS1
0
PS0
0
Micro-program
Power up reset program
6
Zarlink Semiconductor Inc.
MT9094
Data Sheet
0
0
1
Transmit and receive gain control program; with autonulling of the transmit PCM, if the AUTO bit is
set (see address 1Dh)
0
1
0
DTMF generation plus transmit and receive gain control program (autonull available via the AUTO
control bit)
0
1
1
Tone ringer plus transmit and receive gain control program (autonull available via the AUTO control
bit)
1
0
0
handsfree switching program
1
1
1
0
1
1
1
0
1
Last three selections reserved
Note:
For the DSP to function it must be selected to operate, in conjunction with the Filter/Codec, in one of the B-Channels.
Therefore, one of the B-Channel enable bits must be set (see Timing Control, address 15h: bits CH2EN and CH3EN).
Power Up Reset Program
A hardware power-up reset (pin 6, PWRST) will initialize the DSP hardware registers to the default values (all
zeros) and will reset the DSP program counter. The DSP will then be disabled and the PCM streams will pass
transparently through the DSP. The RAM-based registers are not reset by the PWRST pin but may be initialized to
their default settings by programming the DSP to execute the power up reset program. None of the micro-programs
actually require the execution of the power up reset program but it is useful for pre-setting the variables to a known
condition. Note that the reset program requires one full frame (125µSec) for execution.
Gain Control Program
Gain control is performed on converted linear code for both the receive and the transmit PCM. Receive gain control
is set via the hardware register at address 1Dh (see bits B0 - B5) and may be changed at any time. Gain in 1.5 dB
increments is available within a range of +22.5 dB to -72 dB. Normal operation usually requires no more than a +20
to -20 dB range of control. However, the handsfree switching algorithm requires a large attenuation depth to
maintain stability in worst case environments, hence the large (-72 dB) negative limit. Transmit gain control is
divided into two RAM registers, one for setting the network level of transmit speech (address 20h) and the other for
setting the transmit level of DTMF tones into the network (address 21h). Both registers provide gain control in
1.5 dB increments and are encoded in the same manner as the receive gain control register (see address 1Dh, bits
B0 - B5). The power up reset program sets the default values such that the receive gain is set to -72.0 dB, the
transmit audio gain is set to 0.0dB and the transmit DTMF gain is set to -3.0 dB (equivalent to a DTMF output level
of -4 dBm0 into the network).
Optional Offset Nulling
Transmit PCM may contain residual offset in the form of a DC component. An offset of up to ±fifteen linear bits is
acceptable with no degradation of the parameters defined in CCITT G.714. The DPhone-II filter/CODEC
guarantees no more than ±ten linear bits of offset in the transmit PCM when the autonull routine is not enabled. By
enabling autonulling (see AUTO in the Receive Gain Control Register, address 1Dh) offsets are reduced to within
±one bit of zero. Autonulling circuitry was essential in the first generations of Filter/Codecs to remove the large DC
offsets found in the linear technology. Newer technology has made nulling circuitry optional as offered in the
DPhone-II.
7
Zarlink Semiconductor Inc.
MT9094
Data Sheet
DTMF and Gain Control Program
The DTMF program generates a dual cosine wave pattern which may be routed into the receive path as comfort
tones or into the transmit path as network signalling. In both cases, the digitally generated signal will undergo gain
adjustment as programmed into the Receive Gain Control and the Transmit DTMF Gain Control registers. The
composite signal output level in both directions is -4 dBm0 when the gain controls are set to 2Eh (-3.0 dB).
Adjustments to these levels may be made by altering the settings of the gain control registers. Pre-twist of 2.0 dB is
incorporated into the composite signal. The frequency of the low group tone is programmed by writing an 8-bit
coefficient into Tone Coefficient Register 1 (address 23h), while the high group tone frequency uses the 8-bit
coefficient programmed into Tone Coefficient Register 2 (address 24h). Both coefficients are determined by the
following equation:
COEFF = 0.128 x Frequency (in Hz)
where COEFF is a rounded off 8 bit binary integer
A single frequency tone may be generated instead of a dual tone by programming the coefficient at address 23h to
a value of zero. In this case the frequency of the single output tone is governed by the coefficient stored at address
24h.
Frequency
(Hz)
COEF
Actual
Frequency
%
Deviation
697
59h
695.3
-.20%
770
63h
773.4
+.40%
852
6Dh
851.6
-.05%
941
79h
945.3
+.46%
+.20%
1209
9Bh
1210.9
1336
ABh
1335.9
.00%
1477
BDh
1476.6
-.03%
1633
D1h
1632.8
-.01%
Table 1
DTMF Signal to distortion:
The sum of harmonic and noise power in the frequency band from 50 Hz to 3500 Hz is typically more than 30dB below the power in the tone pair.
All individual harmonics are typically more than 40 dB below the level of the low group tone.
Table 1 gives the standard DTMF frequencies, the coefficient required to generate the closest frequency, the actual
frequency generated and the percent deviation of the generated tone from the nominal.
Tone Ringer and Gain Control Program
A locally generated alerting (ringing) signal is used to prompt the user when an incoming call must be answered.
The DSP uses the values programmed into Tone Coefficient Registers 1 and 2 (addresses 23h and 24h) to
generate two different squarewave frequencies in PCM code. The amplitude of the squarewave frequencies is set
to a mid level before being sent to the receive gain control block. From there the PCM passes through the decoder
and receive filter, replacing the normal receive PCM data, on its way to the loudspeaker driver. Both coefficients are
determined by the following equation:
COEFF = 8000/Frequency (Hz)
where COEFF is a rounded off 8 bit binary integer
8
Zarlink Semiconductor Inc.
MT9094
Data Sheet
The ringer program switches between these two frequencies at a rate defined by the 8-bit coefficient programmed
into the Tone Ringer Warble Rate Register (address 26h). The warble rate is defined by the equation:
Tone duration (warble frequency
in Hz) = 500/COEFF
where 0 < COEFF < 256, a warble rate of 5-20 Hz is suggested.
An alternate method of generating ringer tones to the speakerphone speaker is available. With this method the
normal receive speech path through the decoder and receive filter is uninterrupted to the handset, allowing an
existing conversation to continue. The normal DSP and Filter/CODEC receive gain control is also retained by the
speech path. When the OPT bit (DSP Control Register address 1Eh) is set high the DSP will generate the new call
tone according to the coefficients programmed into registers 23h, 24h and 26h as before. In this mode the DSP
output is no longer a PCM code but a toggling signal which is routed directly through the New Call Tone gain control
section to the loudspeaker driver. Refer to the section titled ‘New Call Tone’.
Handsfree Program
A half-duplex speakerphone program, fully contained on chip, provides high quality gain switching of the transmit
and receive speech PCM to maintain loop stability under most network and local acoustic environments. Gain
switching is performed in continuous 1.5 dB increments and operates in a complimentary fashion. That is, with the
transmit path at maximum gain the receive path is fully attenuated and vice versa. This implies that there is a mid
position where both transmit and receive paths are attenuated equally during transition. This is known as the idle
state.
Of the 64 possible attenuator states, the algorithm may rest in only one of three stable states; full receive, full
transmit and idle. The maximum gain values for full transmit and full receive are programmable through the
microport at addresses 20h and 1Dh respectively, as is done for normal handset operation. This allows the user to
set the maximum volumes to which the algorithm will adhere. The algorithm determines which path should maintain
control of the loop based upon the relative levels of the transmit and receive audio signals after the detection and
removal of background noise energy. If the algorithm determines that neither the transmit or the receive path has
valid speech energy then the idle state will be sought. The present state of the algorithm plus the result of the Tx vs.
Rx decision will determine which transition the algorithm will take toward its next stable state. The time durations
required to move from one stable state to the next are parameters defined in CCITT Recommendation P.34 and are
used by default by this algorithm (i.e., build-up time, hang-over time and switching time).
Quiet Code
The DSP can be made to send quiet code to the decoder and receive filter path by setting the RxMUTE bit high.
Likewise, the DSP will send quiet code in the transmit (DSTo) path when the TxMUTE bit is high. Both of these
control bits reside in the DSP Control Register at address 1Eh. When either of these bits are low, their respective
paths function normally.
Transducer Interfaces
Four standard telephony transducer interfaces are provided by the DPhone-II. These are:
•
The handset microphone inputs (transmitter), pins M+/M- and the speakerphone microphone inputs, pins
MIC+/MIC-. The transmit path is muted/not-muted by the MIC EN control bit. Selection of which input pair is
to be routed to the transmit filter amplifier is accomplished by the MIC/HNSTMIC control bit. Both of these
reside in the Transducer Control Register (address 0Eh). The nominal transmit path gain may be adjusted to
either 6.1 dB (suggested for µ-Law) or 15.4 dB (suggested for A-Law). Control of this gain is provided by the
MICA/u control bit (General Control Register, address 0Fh). This gain adjustment is in addition to the
programmable gain provided by the transmit filter and DSP.
9
Zarlink Semiconductor Inc.
MT9094
Data Sheet
•
The handset speaker outputs (receiver), pins HSPKR+/HSPKR-. This internally compensated, fully
differential output driver is capable of driving the load shown in Figure 4. This output is enabled/disabled by
the HSSPKR EN bit residing in the Transducer Control Register (address 0Eh). The nominal handset receive
path gain may be adjusted to either -12.3 dB (suggested for µ-Law) or - 9.7 dB (suggested for A-Law).
Control of this gain is provided by the RxA/u control bit (General Control Register, address 0Fh). This gain
adjustment is in addition to the programmable gain provided by the receive filter and DSP.
•
The loudspeaker outputs, pins SPKR+/SPKR-. This internally compensated, fully differential output driver is
capable of directly driving 6.5vpp into a 40 ohm load. This output is enabled/disabled by the SPKR EN bit
residing in the Transducer Control Register (address 0Eh). The nominal gain for this amplifier is 0.2 dB.
C-Channel
Access to the internal control and status registers of Zarlink basic rate, layer 1, transceivers is through the ST-BUS
Control Channel (C-Channel), since direct microport access is not usually provided, except in the case of the SNIC
(MT8930). The DPhone-II provides asynchronous microport access to the ST-BUS C-Channel information on both
DSTo and DSTi via a double-buffered read/write register (address 14h). Data written to this address is transmitted
on the C-Channel every frame when enabled by CH1EN (see ST-BUS/Timing Control).
HSPKR+
75 Ω
1000 pF
150 ohm
load
MT9094
(speaker)
75 Ω
1000 pF
HSPKR-
ground
Figure 4 - Handset Speaker Driver
LCD
A twelve segment, non-multiplexed, LCD display controller is provided for easy implementation of various set status
and call progress indicators. The twelve output pins (Sn) are used in conjunction with 12 segment control bits,
located in LCD Segment Enable Registers 1&2 (addresses 12h and 13h), and the BackPlane output pin (BP) to
control the on/off state of each segment individually.
The BP pin drives a continuous 62.5 Hz, 50% duty cycle squarewave output signal. An individual segment is
controlled via the phase relationship of its segment driver output pin with respect to the backplane, or common,
driver output. Each of the twelve Segment Enable bits corresponds to a segment output pin. The waveform at each
segment pin is in-phase with the BP waveform when its control bit is set to logic zero (segment off) and is out-ofphase with the BP waveform when its control bit is set to a logic high (segment on). Refer to the LCD Driver
Characteristics for pin loading information.
Microport
A serial microport, compatible with Intel MCS-51 (mode 0) specifications, provides access to all DPhone-II internal
read and write registers. This microport consists of three pins; a half-duplex transmit/receive data pin (DATA1), a
chip select pin (CS) and a synchronous data clock pin (SCLK).
10
Zarlink Semiconductor Inc.
MT9094
Data Sheet
On power-up reset (PWRST) or with a software reset (RST), the DATA1 pin becomes a bidirectional
(transmit/receive) serial port while the DATA2 pin is internally disconnected and tri-stated.
All data transfers through the microport are two-byte transfers requiring the transmission of a Command/Address
byte followed by the data byte written or read from the addressed register. CS must remain asserted for the
duration of this two-byte transfer. As shown in Figure 5, the falling edge of CS indicates to the DPhone-II that a
microport transfer is about to begin. The first 8 clock cycles of SCLK after the falling edge of CS are always used to
receive the Command/Address byte from the microcontroller. The Command/Address byte contains information
detailing whether the second byte transfer will be a read or a write operation and of what address. The next 8 clock
cycles are used to transfer the data byte between the DPhone-II and the microcontroller. At the end of the two-byte
transfer CS is brought high again to terminate the session. The rising edge of CS will tri-state the output driver of
DATA1 which will remain tri-stated as long as CS is high.
Receive data is sampled and transmit data is made available on DATA1 concurrent with the falling edge of SCLK.
Lastly, provision is made to separate the transmit and receive data streams onto two individual pins. This control is
given by the DATASEL pin in the General Control Register (address 0Fh). Setting DATASEL logic high will cause
DATA1 to become the data receive pin and DATA2 to become the data transmit pin. Only the signal paths are
altered by DATASEL; internal timing remains the same in both cases. Tri-stating on DATA2 follows CS as it does on
DATA1 when DATASEL is logic low. Use of the DATASEL bit is intended to help in adapting Motorola (SPI) and
National Semiconductor (Micro-wire) microcontrollers to the DPhone-II. Note that whereas Intel processor serial
ports transmit data LSB first other processor serial ports, including Motorola, transmit data MSB first. It is the
responsibility of the microcontroller to provide LSB first data to the DPhone-II.
COMMAND/ADDRESS (5)
DATA 1
Receive
D0 D1 D2 D3 D4 D5 D6 D7
DATA 1 or DATA 2
Transmit
✈✑✉
DATA INPUT/OUTPUT
✈✑✉
✈✔✉
COMMAND/ADDRESS
D0 D1 D2 D3 D4 D5 D6 D7
D0 D1 D2 D3 D4 D5 D6 D7
D0 D1 D2 D3 D4 D5 D6 D7
D0 D1 D2 D3 D4 D5 D6 D7
SCLK (2)
CS
✈✔✉
✈✓✉
✈✓✉
✈✑✉Delays due to MCS-51 internal timing which are transparent.
✈✒✉The DPhone-II: -latches received data on the falling edge of SCLK
-outputs transmit data on the falling edge of SCLK
✈✓✉The falling edge of CS indicates that a COMMAND/ADDRESS byte will be transmitted from the microprocessor. The subsequent
byte is always data followed by CS returning high.
✈✔✉A new COMMAND/ADDRESS byte may be loaded only by CS cycling high then low again.
D7
✈✕✉The COMMAND/ADDRESS byte contains:
1 bit - Read/Write
0
A5
6 bits - Addressing Data
1 bit - Not used, write logic "0"
D0
A4
A3
A2
A1
A0
R/W
Figure 5 - Serial Port Relative Timing
ST-BUS/Timing Control
A serial link is required for the transport of data between the DPhone-II and the external digital transmission device.
The DPhone-II utilizes the ST-BUS architecture defined by Zarlink Semiconductor. Refer to Zarlink Application Note
11
Zarlink Semiconductor Inc.
MT9094
Data Sheet
MSAN-126. The DPhone-II ST-BUS consists of output and input serial data streams, DSTo and DSTi respectively,
a synchronous clock signal C4i, and a framing pulse F0i.
The data streams operate at 2048 kb/s and are Time Division Multiplexed into 32 identical channels of 64 kb/s
bandwidth. Frame Pulse (a 244 nSec low going pulse) is used to parse the continuous serial data streams into the
32 channel TDM frames. Each frame has a 125 µSecond period translating into an 8 kHz frame rate. Valid frame
pulse occurs when F0i is logic low coincident with a falling edge of C4i. C4i has a frequency (4096 MHz) which is
twice the data rate. This clock is used to sample the data at the _ bit-cell position on DSTi and to make data
available on DSTo at the start of the bit-cell. C4i is also used to clock the DPhone-II internal functions (i.e., DSP,
Filter/CODEC, HDLC) and to provide the channel timing requirements.
The DPhone-II uses channels 1, 2 & 3 of the 32 channel frame. These channels are always defined, beginning with
the first channel after frame pulse, as shown in Figure 6 (DSTi and DSTo channel assignments). Channels are
enabled independently by the three control bits Ch1En -Ch3En residing in the Timing Control Register
(address15h).
Ch1EN - C-Channel
Channel 1 conveys the control/status information for Zarlink’s layer 1 transceiver. The full 64 kb/s bandwidth is
available and is assigned according to which transceiver is being used. Consult the data sheet for the selected
transceiver for its bit definitions and order of bit transfer. When this bit is high register data is transmitted on DSTo.
When low, this timeslot is tri-stated on DSTo. Receive C-Channel data (DSTi) is always routed to the register
regardless of this control bit's logic state. C-channel data is transferred on the ST-BUS MSB first by the DPhone-II.
Ch2EN and Ch3EN - B1-Channel and B2-Channel
Channels 2 and 3 are the B1 and B2 channels, respectively. These bits (Ch2EN and Ch3EN) are used to enable the
PCM channels from/to the DPhone-II as required.
Transmit PCM on DSTo
When high, PCM from the Filter/CODEC and DSP is transmitted on DSTo in the selected ST-BUS channel. When low,
DSTo is forced to logic 0 for the corresponding timeslot. If both Ch2EN and Ch3EN are enabled, default is to channel 2.
Receive PCM from DSTi
When high, PCM from DSTi is routed to the DSP and Filter/CODEC in the associated channel. If both Ch2EN and
Ch3EN are enabled the default is to channel 2.
New Call Tone
The New Call Tone Generator produces a frequency shifted square-wave used to toggle the speaker driver outputs.
This is intended for use where a ringing signal is required concurrently with an already established voice
conversation in the handset.
Programming of the DSP for New Call generator is exactly as is done for the tone ringer micro-program except that
the OPT bit (DSP Control Register, address 1Eh) is set high. In this mode the DSP does not produce a frequency
shifted squarewave output to the filter CODEC section. Instead the DSP uses the contents of the tone coefficient
registers, along with the tone warble rate register, to produce a gated squarewave control signal output which
toggles between the programmed frequencies. This control signal is routed to the New Call Tone block when the
NCT EN control bit is set (General Control Register, address 0Fh). NCT EN also enables a separate gain control
block, for controlling the loudness of the generated ringing signal. With the gain control block set to 0 dB the output
is at maximum or 6 volts p-p. Attenuation of the applied signal, in three steps of 8 dB, provide the four settings for
New Call tone (0, -8, -16, -24 dB). The NCT gain bits (NCTG0-NCTG1) reside in the FCODEC Gain Control Register
2 (address 0Bh).
12
Zarlink Semiconductor Inc.
MT9094
Data Sheet
125 µs
F0i
DSTi,
DSTo
Not
Used
CHANNEL 1
C-channel
CHANNEL 2
B1-channel
CHANNEL 3
B2-channel
CHANNELS 4 - 31
Not Used
MSB first for C, B1 - & B2Channels
Figure 6 - ST-BUS Channel Assignment
Watchdog
To maintain program integrity an on-chip watchdog timer is provided for connection to the microcontroller reset pin.
The watchdog output WD (pin 17) goes high while the DPhone-II is held in reset via the PWRST (pin 6). Release of
PWRST will cause WD to return low immediately and will also start the watchdog timer. The watchdog timer is
clocked on the falling edge of F0i and requires only this input, along with VDD, for operation.
If the watchdog reset word is written to the watchdog register (address 11h) after PWRST is released, but before
the timeout period (T=512mSec) expires, a reset of the timer results and WD will remain low. Thereafter, if the reset
word is loaded correctly at intervals less than 'T' then WD will continue low. The first break from this routine, in
which the watchdog register is not written to within the correct interval or it is written to with incorrect data, will result
in a high going WD output after the current interval 'T' expires. WD will then toggle at this rate until the watchdog
register is again written to correctly.
5-BIT WATCHDOG RESET WORD
X
X
X
W4
W3
W2
W1
W0
0
1
0
1
0
x=don’t care
DPhone-II Register Map
Address
(Hex)
WRITE
READ
00-09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17-1C
RESERVED
FCODEC GAIN CONTROL REGISTER 1
FCODEC GAIN CONTROL REGISTER 2
RESERVED
RESERVED
TRANSDUCER CONTROL REGISTER
GENERAL CONTROL REGISTER
RESERVED
WATCHDOG REGISTER
LCD SEGMENT ENABLE REGISTER 1
LCD SEGMENT ENABLE REGISTER 2
C-CHANNEL REGISTER (to DSTo)
TIMING CONTROL REGISTER
LOOP-BACK REGISTER
RESERVED
RESERVED
VERIFY
VERIFY
RESERVED
RESERVED
VERIFY
VERIFY
RESERVED
NOT USED
VERIFY
VERIFY
C-CHANNEL REGISTER (from DSTi)
VERIFY
VERIFY
RESERVED
13
Zarlink Semiconductor Inc.
MT9094
Data Sheet
DPhone-II Register Map
Address
(Hex)
WRITE
READ
1D
1E
1F
20
21
22
23
24
25
26
27-3F
RECEIVE GAIN CONTROL REGISTER
DSP CONTROL REGISTER
RESERVED
TRANSMIT AUDIO GAIN REGISTER
TRANSMIT DTMF GAIN REGISTER
RESERVED
TONE COEFFICIENT REGISTER 1
TONE COEFFICIENT REGISTER 2
RESERVED
TONE RINGER WARBLE RATE REGISTER
RESERVED
VERIFY
VERIFY
RESERVED
VERIFY
VERIFY
RESERVED
VERIFY
VERIFY
RESERVED
VERIFY
RESERVED
Test Loops
Detail LBio and LBoi Loopback Register (address 16h)
LBio
Setting this bit causes data on DSTi to be looped back to DSTo directly at the pins. The appropriate channel
enables Ch1EN -Ch3EN must also be set.
LBoi
Setting this bit causes data on DSTo to be looped back to DSTi directly at the pins.
14
Zarlink Semiconductor Inc.
MT9094
Data Sheet
Register Summary
This section contains a complete listing of the DPhone-II register addresses, the control/status bit mapping
associated with each register and a definition of the function of each control/status bit.
The Register Summary may be used for future reference to review each of the control/status bit definitions without
the need to locate them in the text of the functional block descriptions.
ADDRESSES 00h and 09h are RESERVED
FCODEC Gain Control Register 1
ADDRESS = 0Ah WRITE/READ VERIFY
RxFG2 RxFG1 RxFG0
7
6
Receive Gain
Setting (dB)
0
5
-
4
3
RxFG2
RxFG1
RxFG0
Power Reset Value
X000 X000
TxFG2 TxFG1 TxFG0
2
1
0
Transmit Gain
Setting (dB)
TxFG2
TxFG1
TxFG0
0
0
0
(default) 0
0
0
0
-1
0
0
1
1
0
0
1
-2
0
1
0
2
0
1
0
-3
0
1
1
3
0
1
1
-4
1
0
0
4
1
0
0
-5
1
0
1
5
1
0
1
-6
1
1
0
6
1
1
0
-7
1
1
1
7
1
1
1
(default)
RxFGn = Receive Filter Gain n
TxFGn = Transmit Filter Gain n
FCODEC Gain Control Register 2
-
NCTG1 NCTG0
-
7
ADDRESS = 0Bh WRITE/READ VERIFY
6
5
4
-
STG2
3
2
STG1
1
Power Reset Value
0X00 X000
STG0
0
Side-tone Gain
Setting (dB)
STG2
STG1
STG0
0
(default) OFF
0
0
0
1
-9.96
0
0
1
1
0
-6.64
0
1
0
1
1
-3.32
0
1
1
0
1
0
0
3.32
1
0
1
6.64
1
1
0
9.96
1
1
1
Gain (dB)
NCTG1
NCTG0
0 (default)
0
-8
0
-16
-24
NCTGn = New Call Tone Gain n
STGn= Side-tone Gain n
15
Zarlink Semiconductor Inc.
MT9094
Data Sheet
ADDRESSES 0Ch and 0Dh are RESERVED
Note: Bits marked "-" are reserved bits and should be written with logic "0".
Transducer Control Register
PuFC
Tfhp
7
6
PuFC
ADDRESS = 0Eh WRITE/READ VERIFY
DIAL
EN
5
SIDE
EN
4
MIC
EN
3
MIC/
HNSTMIC
2
SPKR
EN
1
DIAL EN
SIDE EN
MIC EN
MIC/HNSTMIC
SPKR EN
HSSPKR EN
General Control Register
RST
7
DATASEL
A/u
Sign-mag/CCITT
RxA/u
MICA/u
SIDEA/u
NCT EN
EN
Power Reset Value
0000 0000
0
When high, the Filter/CODEC is powered up. When low, the Filter/CODEC is powered down. If PuFC, SPKR EN and
HSSPKR EN are all low then the VRef/VBias circuit is also powered down.
When high, an additional high pass function (passband beginning at 400 Hz) is inserted into the transmit path. When low, this
highpass filter is disabled.
When high, a first order lowpass filter is inserted into the receive path (3 dB = 1 kHz). When low, this lowpass filter is disabled.
When high, the sidetone path is enabled (assuming STG2-0 are not all low). When low, the sidetone path is disabled.
When high, the selected transmit microphone is enabled to the transmit filter section. When low, the microphone path is muted.
When high, the handsfree microphone (pins MIC±) is muxed into the transmit path. When low, the handset microphone (pins
M±) is muxed into the transmit path. Both are contingent on "MIC EN".
When high, the handsfree loudspeaker driver is powered up. When low, this driver is powered down.
When high, the handset speaker driver is powered up. When low, this driver is powered down.
Tfhp
RST
HSSPKR
DATA
SEL
6
ADDRESS = 0Fh WRITE/READ VERIFY
A/µ
5
Sign-Mag/
CCITT
4
Rx
A/µ
MIC
A/µ
3
2
Side
A/µ
NCT
EN
1
0
Power Reset Value
0000 0000
Active high reset. Performs the same function as PWRST but does not affect the microport or the watchdog circuits. To remove
this reset a PWRST must occur or this bit must be written low.
When high, the microport transmit and receive are performed on separate pins. DATA1 is receive while DATA2 is transmit.
When low, the microport conforms to Intel MCS-51 mode 0 specifications; DATA1 is a bi-directional (transmit/receive) serial
data pin while DATA2 is internally disconnected and tri-stated.
When high, A-Law (de)coding is selected. When low, µ-Law (de)coding is selected.
When high, sign-magnitude bit coding is selected, When low, true CCITT PCM coding is selected.
When high, the receiver driver nominal gain is set at -9.7 dB. When low this driver nominal gain is set at -12.3 dB.
When high, the transmit amplifier nominal gain is set at 15.4 dB. When low this amplifier nominal gain is set at 6.1 dB.
When high, the side-tone nominal gain is set at -18.8 dB. When low this nominal gain is set at -11 dB.
When high, the new call tone generator output from the DSP is selected as the source for the loudspeaker path. When low, the
CODEC output is selected for the loudspeaker path. Note that SPKR EN must also be set high for new call tone to function.
ADDRESS 10h is RESERVED
Note: Bits marked "-" are reserved bits and should be written with logic "0".
16
Zarlink Semiconductor Inc.
MT9094
Data Sheet
Watchdog Register
7
ADDRESS = 11h WRITE
-
-
6
5
W4
W3
W2
W1
W0
4
3
2
1
0
Power Reset Value
XXX0 1010
WATCHDOG RESET WORD - XXX01010
LCD Segment Enable Register 1
ADDRESS = 12h WRITE/READ VERIFY
SC8
SC7
SC6
SC5
SC4
SC3
SC2
SC1
7
6
5
4
3
2
1
0
Power Reset Value
0000 0000
Twelve segment control bits used for the LCD outputs. When high the respective segment is on. When low the respective segment is off.
LCD Segment Enable Register 2
ADDRESS = 13h WRITE/READ VERIFY
-
-
-
-
SC12
SC11
SC10
SC9
7
6
5
4
3
2
1
0
Power Reset Value
XXXX 0000
Twelve segment control bits used for the LCD outputs. When high the respective segment is on. When low the respective segment is off.
C-Channel Register
ADDRESS = 14h WRITE/READ
D7
D6
D5
D4
D3
D2
D1
D0
7
6
5
4
3
2
1
0
Micro-port access to the ST-BUS C-Channel information.
Note: Bits marked "-" are reserved bits and should be written with logic "0".
17
Zarlink Semiconductor Inc.
Power Reset Value
Write = 1111 1111
Read = Not Applicable
MT9094
Data Sheet
Timing Control Register
ADDRESS = 15h WRITE/READ VERIFY
-
-
-
-
7
6
5
4
CH3EN CH2EN CH1EN
3
2
1
Power Reset Value
XX0X 0000
0
All bits active high:
Ch2EN and Ch3EN
Channels 2 and 3 are the B1 and B2 channels, respectively. PCM associated with the DSP, Filter/CODEC and transducer audio
paths is conveyed in one of these channels as selected in the timing control register.
Transmit B1 and B2 data on DSTo
When high PCM from the Filter/CODEC and DSP is transmitted on DSTo in the associated channel. When low DSTo is
forced to logic 0 for the corresponding timeslot. If both Ch2EN and Ch3EN are enabled, data defaults to channel 2.
Receive B1 and B2 data on DSTi
When enabled PCM from DSTi is routed to the DSP and Filter/CODEC in the associated channel. If both Ch2EN and Ch3EN
Ch1EN
are enabled, data input defaults to channel 2.
Channel 1 conveys the control/status information for the layer 1 transceiver. The full 64kb/s bandwidth is available and is assigned
according to which transceiver is being used. Consult the data sheets for the transceiver selected. When high register data is transmitted on DSTo. When low this timeslot is tri-stated on DSTo. Receive C-Channel data (DSTi) is always routed to the register
regardless of this control bit's logic state.
Loop-back Register
7
ADDRESS = 16h WRITE/READ VERIFY
LBio
LBoi
-
-
-
-
-
6
5
4
3
2
1
0
Power Reset Value
X00X XXXX
LBio
Active high enables data from the ST-BUS input to be looped back to the ST-BUS output directly at the pins. The DSTo tri-state driver
LBoi
must also be enabled using one of the channel enable signals.
Active high enables data from ST-BUS output to be looped back to the ST-BUS input directly at the pins.
ADDRESSES 17h - 1Ch are RESERVED
Note: Bits marked "-" are reserved bits and should be written with logic "0".
18
Zarlink Semiconductor Inc.
MT9094
Data Sheet
Receive Gain Control Register
AUTO
B5-B0
ADDRESS = 1Dh WRITE/READ VERIFY
-
AUTO
B5
B4
B3
B2
B1
B0
7
6
5
4
3
2
1
0
Power Reset Value
0000 0000
When high autonulling of the transmit PCM is enabled. When low, autonulling is disabled. This bit is used in conjunction with the PS2 PS0 bits of the DSP Control Register at address 1Eh.
These 6 bits (indicated below in hexadecimal) are decoded to control Rx PCM gain:
B5-B0
Gain Setting (dB)
B5-B0
Gain Setting (dB)
3F
3E
3D
3C
3B
3A
39
38
37
36
35
34
33
32
31
30
2F
2E
2D
2C
2B
2A
29
28
27
26
25
24
23
22
21
20
+22.5
+21.0
+19.5
+18.0
+16.5
+15.0
+13.5
+12.0
+10.5
+9.0
+7.5
+6.0
+4.5
+3.0
+1.5
+0.0
-1.5
-3.0
-4.5
-6.0
-7.5
-9.0
-10.5
-12.0
-13.5
-15.0
-16.5
-18.0
-19.5
-21.0
-22.5
-24.0
1F
1E
1D
1C
1B
1A
19
18
17
16
15
14
13
12
11
10
0F
0E
0D
0C
0B
0A
09
08
07
06
05
04
03
02
01
00
-25.5
-27.0
-28.5
-30.0
-31.5
-33.0
-34.5
-36.0
-37.5
-39.0
-40.5
-42.0
-43.5
-45.0
-46.5
-48.0
-49.5
-51.0
-52.5
-54.0
-55.5
-57.0
-58.5
-60.0
-61.5
-63.0
-64.5
-66.0
-67.5
-69.0
-70.5
-72.0
Note: B0-B5 of addresses 20h and 21h are encoded in the same manner
Note: Bits marked "-" are reserved bits and should be written with logic "0".
19
Zarlink Semiconductor Inc.
MT9094
Data Sheet
DSP Control Register
ADDRESS = 1Eh WRITE/READ VERIFY
PS2
PS1
7
6
OPT:
RxMUTE:
TxMUTE:
DRESET:
PS0
5
OPT
RxMUTE
TxMUTE
-
DRESET
4
3
2
1
0
Power Reset Value
0000 0000
When high, the tone ringer is in New Call tone mode. When low the normal tone ringer program is executed.
This bit when high turns off the receive PCM channel, substituting quiet code.
This bit when high turns off the transmit PCM channel, substituting quiet code.
This bit (when high) enables the DSP. If low, no programs are executed, the master clock is disabled and the program counter is
reset to zero.
These bits are program select bits for the DSP Rom programs.
PS2-PS0:
PS2
PS1
PS0
MICRO-PROGRAM
0
0
0
Power up reset program
0
0
1
Gain control program
0
1
0
DTMF & Gain control program
0
1
1
Tone Ringer & Gain control program
1
0
0
Handsfree program
1
0
1
Reserved
1
1
0
Reserved
1
1
1
Reserved
ADDRESS 1Fh is RESERVED
Transmit Audio Gain Register
-
7
ADDRESS = 20h WRITE/READ VERIFY
B5
B4
B3
B2
B1
B0
5
4
3
2
1
0
6
Power Reset Value
XX11 0000
This register controls the transmit speech path gain in 1.5dB steps as in Receive Gain Register (address 1Dh).
ADDRESS = 21h WRITE/READ VERIFY
Transmit DTMF Gain Register
-
7
6
B5
B4
B3
B2
B1
B0
5
4
3
2
1
0
Power Reset Value
XX10 1110
This register controls the transmit DTMF level in 1.5dB steps as in Receive Gain Register (address 1Dh).
ADDRESS 22h is RESERVED
Note: Bits marked "-" are reserved bits and should be written with logic "0".
20
Zarlink Semiconductor Inc.
MT9094
Data Sheet
Tone Coeff Register 1-DTMF or Tone Ringer
ADDRESS = 23h WRITE/READ VERIFY
B7
B6
B5
B4
B3
B2
B1
B0
7
6
5
4
3
2
1
0
Power Reset Value
0000 0000
This register is used to program the low-group frequency of the DTMF program. The tone coefficient is calculated as follows:
COEF = 0.128 x Frequency
where: Frequency is in Hz (note: COEF must be converted to an 8 bit binary integer)
Highest frequency possible:
1992.2 Hz
Lowest frequency possible:
7.8 Hz
Frequency resolution:
7.8 Hz
-2.1 dB ± 0.2 dB
Pre-twist:
This register is used to program the first frequency of the squarewave ringer program. The tone coefficient is calculated as follows:
COEF = 8000 / Frequency
where: Frequency is in Hz (note: COEF must be rounded off and converted to an 8 bit binary integer)
Highest frequency possible:
4000 Hz
Lowest frequency possible:
31.4 Hz
Frequency resolution:
non-linear
This tone can be disabled by writing zero to this register for single tone generation.
Tone Coeff Register 2-DTMF or Tone Ringer
ADDRESS = 24h WRITE/READ VERIFY
B7
B6
B5
B4
B3
B2
B1
B0
7
6
5
4
3
2
1
0
Power Reset Value
0000 0000
This register is used to program the high-group frequency of the DTMF program. The tone coefficient is calculated as follows:
COEF = 0.128 x Frequency
where: Frequency is in Hz (note: COEF must be converted to an 8 bit binary integer)
Highest frequency possible:
1992.2 Hz
Lowest frequency possible:
7.8 Hz
Frequency resolution:
7.8 Hz
Pre-twist:
0 dB
This register is used to program the second frequency of the squarewave program. The tone coefficient is calculated similarly to tone coefficient register 1.
ADDRESS 25h is RESERVED
21
Zarlink Semiconductor Inc.
MT9094
Data Sheet
Tone Ringer Warble Rate-Tone Ringer
ADDRESS = 26h WRITE/READ VERIFY
B7
B6
B5
B4
B3
B2
B1
B0
7
6
5
4
3
2
1
0
Power Reset Value
0000 0000
The tone ringer will switch between squarewave frequencies at a warble frequency defined by this register. The relationship between the duration
period of each tone and the 8 bit warble coefficient is as follows:
Tone duration (warble frequency) = 500 / COEF
where: Frequency is in Hz, and 0≤COEF <256
Highest frequency possible:
500 Hz
Lowest frequency possible:
2.0 Hz
Frequency resolution:
non-linear
Addresses:
27h to 2Dh are transmit and receive gains and coefficients used by the filters in the handsfree decision circuit.
2Eh to 3Fh are scratch-pad ram locations used by the DSP algorithms as temporary storage during calculations.
Applications
To maintain a fully differential topology in the transmit path the suggested connection scheme for the transmit
microphones is shown in Figure 7. However, it is possible to use a single-ended arrangement as shown in Figure 8
for the transmit interface. In this case the dynamic range of the MT9094 is reduced by half. In both figures the
output drivers are connected in a fully differential manner.
The MT9094 is a member of the Zarlink family of digital terminal equipment components. There are two
transmission devices which connect directly with the MT9094 to complete an application; the MT8930 (SNIC) and
the MT8971/72 (DSIC/DNIC). An ISDN 4-wire "TE" function is implemented with the MT8930/MT9094 combination.
A 2-wire digital phone for PABX, key-systems and other proprietary applications is implemented with the
MT8971/72/MT9094 combination.
Figures 9 and 10 show the 4-wire and 2-wire applications, respectively.
22
Zarlink Semiconductor Inc.
MT9094
Data Sheet
330Ω
+5V
+
+
-
2R
T
Av = 1+
+
VBias
T
R
100K
-
10µF
511Ω
0.1µF
100K
R
0.1µF
Electret
Microphone
330Ω
511Ω
+5V
+
+
100K
R
Av = 1+
0.1µF
2R
T
T
R
0.1µF
+
Electret
Microphone
0.1µF
511Ω
-
+5V
6
DSTi
DSTo
C4i
F0i
5
4
3
SCLK
DATA2
DATA1
CS
WD
2
1
44
43 42
41 40
7
39
8
38
9
37
10
36
11
35
MT9094
12
Serial
Microport
INTEL
MCS-51
100K
10µF
511Ω
0.1µF
VBias
+
VBias
ST-BUS
Port
to
Transmission
Device
+
-
33
14
32
15
31
16
30
17
29
19
20
21
22 23
40Ω nom.
32Ω min.
75Ω
150Ω
+5V
75Ω
34
13
18
+
24 25
26 27
28
.1µF 1000pF
1000pF
LCD
Note: Single-ended configurations reduce
dynamic range by a factor of two.
LCD
Figure 7 - Application Circuit - fully differential audio input
23
Zarlink Semiconductor Inc.
1000pF caps
are optional
MT9094
+
–
330Ω
+5V
VBias
+
T
10µF
1K
1µF
R
Data Sheet
+
Electret
Microphone
+
VBias
–
T
330Ω
+5V
+
10µF
1K
1µF
R
+
0.1µF
Electret
Microphone
0.1µF
VBias
+5V
6
ST-BUS
Port
to
Transmission
Device
5
4
3
2
44 43 42 41 40
DSTi
7
39
DSTo
8
38
9
37
10
36
11
35
C4i
F0i
MT9094
12
Serial
Microport
INTEL
MCS-51
1
34
SCLK 13
33
14
32
DATA2
DATA1 15
31
CS 16
30
WD 17
29
18
19
20
21
22
23
24
25
26
27
+
32Ω min.
75Ω
150Ω
+5V
75Ω
.1µF 1000pF
Note: Single-ended configurations reduce
dynamic range by a factor of two.
LCD
Figure 8 - Application Circuit - single-ended audio input
Zarlink Semiconductor Inc.
1000pF
1000pF caps
are optional
LCD
28
24
40Ω nom.
MT9094
Data Sheet
LTx
HSPKR+
C4b
C4i
HSPKR-
CCITT ISDN
Reference
Point S
Interface
F0b
5 Volts
DC to DC
Converter
VBias
MT8930
SNIC
with
HDLC
Controller
F0i
DSTo
DSTi
DSTi
DSTo
MT9094
DPhone-∏
Handset
M+
MMIC+
MIC-
Microphone
AD0-7
SPKR+
LRx
IRQ
(ALE)
(RD)
(WR)
SPKR-
IRQ
CS
SCLK
AS
(ALE)
DATA1
E
(RD)
R/W
(WR)
AD0-7
IRQ
8051
INTEL
MCS51
Figure 9 - CCITT ISDN Voice/Data Terminal Equipment - TE1
25
Zarlink Semiconductor Inc.
Speaker
MT9094
5 volts
DC to DC
CONVERTER
C4
C4i
F0
F0i
HSPKR+
HSPKR-
MT8972
Lin
DNIC
ZT
Twisted Pair
to Central
PBX
Data Sheet
DSTo
DSTi
DSTi
DSTo
MT9094
DPhone-∏
M+
Handset
MMIC+
MIC-
Lout
Microphone
SPKR+
SPKR10.24 MHz
SCLK CS
DATA1
INTEL
MCS-51
Figure 10 - Voice/Data Digital Telephone Set Circuit
26
Zarlink Semiconductor Inc.
Speaker
MT9094
Data Sheet
Programming Examples
Some examples of the programming steps required to set-up various telephony functions are given. Note that these
steps are from the power-up reset default definition. If some other state is currently true then some programming
steps may be omitted while new ones may be required.
Standard Full-duplex handset call
Description
select B-Channel of operation
Address
15h
DATA
bits 2 or 3 (as required)
reset DSP
set Rx gain (ie 0dB with Tx
set Tx gain (ie 0dB)
start Rx gain program
1Eh
1Dh
20h
1Eh
00h
70h (or as required)
30h (or as required)
21h
select transducers and turn on
sidetone and filter/CODEC
0Eh
99h
set sidetone gain
0Bh
04h (for 0dB or as required)
optional:
set CODEC Rx and Tx gain
select A-Law versus µ-Law
0Ah
0Fh
as required (0dB default)
bits 1-5 (as required)
Description
select B-Channel of operation
Address
15h
DATA
bits 2 or 3 (as required)
reset DSP
set Rx gain (ie 12 dB)
set Tx gain (ie 0dB)
start handsfree program
1Eh
1Dh
20h
1Eh
00h
38h (or as required)
30 h (or as required)
81h
select transducers and filter/CODEC
and turn off sidetone
0Eh
1Eh
0Ah
0Fh
as required (0dB default)
bits 1-5 (as required)
Description
select B-Channel of operation
Address
15h
DATA
bits 2 or 3 (as required)
reset DSP
set Rx gain (ie 0 dB with Tx
autonull)
set Tx gain (ie 0dB)
write tone coefficient 1
write tone coefficient 2
write warble tone rate coefficient
start tone ringer program
1Eh
1Dh
00h
70h (or as required)
20h
23h
24h
26h
1Eh
30h (or as required)
as required
as required
as required
61h
select speaker and filter/CODEC
and turn off sidetone
0Eh
82h
control ringer cadence by toggling
RxMUTE
1Eh
61
69
61
69
autonull)
Half-Duplex handsfree operation
optional:
set CODEC Rx and Tx gain
select A-Law versus µ-Law
Generate tone ringer
27
Zarlink Semiconductor Inc.
(on)
(off)
(on)
(off) etc...
MT9094
Data Sheet
Generate DTMF tones
Description
select B-Channel of operation
Address
15h
DATA
bits 2 or 3 (as required)
reset DSP
set Rx DTMF gain (ie -20 dBm0)
set Tx audio gain (ie 0dB)
set Tx DTMF gain (ie -4dBm0)
write tone coefficient 1
write tone coefficient 2
start DTMF program
1Eh
1Dh
20h
21h
23h
24h
1Eh
00h
22h (or as required)
30h (or as required)
2Eh (or as required)
as required
as required
41h
select transducers and filter/CODEC
(PuFC)
and turn off sidetone
0Eh
as required
0Ah
as required (0dB default)
1Eh
as required
optional:
set CODEC Rx gain
send tones in only Rx or Tx by
disabling
RxMUTE or TxMUTE appropriately
New Call Tone
Description
Address
DATA
Assume that a B-Channel of operation has already been selected for the concurrent handset
conversation.
If this is not true select one.
select B-Channel of operation
15h
bits 2 or 3 (as required)
reset DSP
1Eh
00h
**********************************************************************************
set Rx gain (ie 0 dB with Tx autonull)
set Tx gain (ie 0dB)
1Dh
20h
70h (or as required)
30h (or as required)
Note: these two steps a required for the concurrent conversation only and do not affect new
call tone generation. See Standard Full-duplex handset call for required programming.
**********************************************************************************
write
write
write
start
tone coefficient 1
tone coefficient 2
warble rate coefficient
new call tone ringer program
23h
24h
26h
1Eh
as required
as required
as required
71h
set new call tone gain
0Bh
NCTG2-1 (as required)
select speaker
0Eh
02h
9Bh (assuming a concurrent handset
call)
enable new call tone
0Fh
01h (assuming all other bits are µ-Law
control ringer cadence by toggling
between gain control and tone ringer
with gain control programs
1Eh
71h (on)
31h (off)
71h (on) etc...
28
Zarlink Semiconductor Inc.
MT9094
Data Sheet
Absolute Maximum Ratings
Parameter
Symbol
Min.
Max.
Units
VDD-VSS
-0.3
7
V
VI/VO
VSS-0.3
VDD+0.3
V
±20
mA
+150
°C
PD
750
mW
±2.0
KV
1
Supply Voltage
2
Voltage on any I/O pin
3
Current on any I/O pin (transducers excluded)
4
Storage Temperature
5
Power Dissipation (package)
6
Static Discharge
ESD
7
Latch-up Current
ILU
II/IO
-65
TS
Plastic
±100
mA
Recommended Operating Conditions - Voltages are with respect to VSS unless otherwise stated.
Characteristics
Sym.
Min.
Typ.
Max.
Units
5
5.25
V
Test Conditions
1
Supply Voltage
VDD
4.75
2
Input Voltage (high) *
VIH
2.4
VDD
V
Noise margin = 400 mV
3
Input Voltage (low) *
VIL
VSS
0.4
V
Noise margin = 400 mV
4
Operating Temperature
TA
-40
+85
°C
5
Clock Frequency (C4i)
fCLK
4092
4100
kHz
4096
* Excluding PWRST which is a Schmitt Trigger Input.
Power Characteristics
Characteristics
1
Supply Current (clock enabled, all
functions off
2
Supply Current by function
Filter/Codec
DSP
Handset Driver (bias only, no signal)
Speaker Driver (bias only, no signal)
Timing Control, C-Channel, ST-BUS,
etc.
Total all functions enabled
Sym.
Min.
Typ.
IDDC1
IDDF1
IDDF3
IDDF4
IDDF5
IDDF6
1.5
1.5
1.5
1.5
1.0
IDDFT
7.0
Note 1: Power delivered to the load is in addition to the bias current requirements.
Note 2: IDDFT is not additive to IDDC1.
29
Zarlink Semiconductor Inc.
Max.
Units
6
mA
mA
mA
mA
mA
mA
14
mA
Test Conditions
See Note 1.
See Note 1.
See Note 2.
MT9094
Data Sheet
DC Electrical Characteristics† (except LCD Drive Pins) - Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
Sym.
Min.
2.0
1
Input HIGH Voltage TTL inputs
VIN
2
Input LOW Voltage TTL inputs
VIL
3
VBias Voltage Output
4
5
Typ.‡
Units
Test Conditions
V
0.8
V
V
Max. Load = 100 µA
µA
VIN = VDD to VSS
-16
mA
VOH = 2.4V DSTo, WD,
DATA1,
DATA2
10
mA
VOL = 0.4V DSTo, WD,
DATA1,
DATA2
VRef
(VDD/2)-1.5
V
IOZ
0.01
VBias
VDD/2
Input Leakage Current 1
IIZ
0.1
Positive Going Threshold
Voltage (PWRST only)
Negative Going Threshold
Voltage (PWRST only)
VT+
6
Output HIGH Current TTL O/P
IOH
-10
7
Output LOW Current TTL O/P
IOL
5
8
Output Voltage
1
Max.
10
3.3
VT-
1.5
10
No load
µA
9
Output Leakage Current
10
Output Capacitance
Co
15
pF
11
Input Capacitance
Ci
10
pF
VOUT = VDD and VSS
† DC Electrical Characteristics are over recommended temperature and range & recommended power supply voltages.
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
Note 1 TTL compatible pins only.
DC Electrical Characteristics† - LCD Drive Pins - Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
Sym.
Min.
Typ.
Max.
Units
Test Conditions
1
Output High Voltage Both
Segment and Backplane
VOH
4.8
---
---
Volts
Io = 1 mA, VDD = 5 V
2
Output Low Voltage Both
Segment and Backplane
VOL
---
---
0.2
Volts
Io = 1 mA, VDD = 5 V
3
Segment Output Load
---
---
1200
pF
4
Backplane Output Load
---
---
7200
pF
5
Frequency
62
62.5
63
Hz
30
Zarlink Semiconductor Inc.
MT9094
Data Sheet
AC Characteristics† for A/D (Transmit) Path - 0dBm0 = 1.421Vrms for µ-Law and 1.477Vrms for A-Law, at the CODEC. (VRef =
0.5 volts and VBias = 2.5 volts). All parameters pertain exclusively to the Filter/CODEC except absolute half-channel gain and transmit idle
channel noise.
Characteristics
Sym.
Min.
1
Analog input equivalent to
overload decision
ALi3.17
ALi3.14
2
Absolute half-channel gain.
Transmit filter gain = 0 dB setting
GAX1
GAX2
5.4
14.7
All other transmit filter settings
(1 to 7 dB) are in addition to 0 dB
setting
GAX1
GAX2
3
Gain tracking vs. input level
CCITT G.714 Method 2
4
Typ.‡
Max
5.79
6.0
6.1
15.4
Units
Vp-p
Vp-p
Test Conditions
µ-Law
A-Law
Both at CODEC
6.8
16.1
dB
dB
MICA/u=0*
MICA/u=1*
MIC± or M± to PCM
1020Hz
-0.15
-0.15
+0.15
+0.15
dB
dB
MICA/u=0*
MICA/u=1*
from nominal
MIC± or M± to PCM
1020 Hz
GTX
-0.3
-0.6
-1.6
0.3
0.6
1.6
dB
dB
dB
3 to -40 dBm0
-40 to -50 dBm0
-50 to -55 dBm0
Signal to total Distortion vs. input
level
CCITT G.714 Method 2
DQX
35
29
24
dB
dB
dB
0 to -30dBm0
-40 dBm0
-45 dBm0
5
Transmit Idle Channel Noise
NCX
NPX
6
Gain relative to gain at 1020 Hz
<50 Hz
60 Hz
200 Hz
300-3000 Hz
3000-3400 Hz
4000 Hz
>4600 Hz
GRX
7
Absolute Delay
DAX
360
µs
at frequency of minimum
delay
8
Group Delay relative to DAX
DDX
750
380
130
750
µs
µs
µs
µs
500-600 Hz
600-1000 Hz
1000-2600 Hz
2600 - 2800 Hz
9
Power Supply Rejection
f=1020 Hz
f=0.3 to 3 kHz
f=3 to 4 kHz
f=4 to 50 kHz
15
-72
-0.25
-0.9
PSSR
PSSR1
PSSR2
PSSR3
17.5
-66
dBrnC0
dBrn0p
-25
-30
0.0
0.25
0.25
-12.5
-25
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
37
40
35
40
† AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
* Note: MICA/u, refer to General Control Register, address 0Fh.
31
Zarlink Semiconductor Inc.
µ-Law
A-Law
100mVrms signal
µ-Law
PSSR1-3 not production
tested
MT9094
Data Sheet
AC Characteristics† for D/A (Receive) Path - 0dBm0 = 1.421Vrms for µ-Law and 1.477Vrms for A-Law, at the CODEC. (VRef = 0.5
volts and VBias = 2.5 volts). All parameters pertain exclusively to the Filter/CODEC except absolute gain and receive idle channel noise.
Characteristics
Sym.
Typ.‡
Min.
Max.
5.704
5.906
1 Analog output at the CODEC full
scale
ALo3.17
ALo3.14
2 Absolute half-channel gain.
Receive filter gain = 0 dB setting
GAR1
GAR2
GAR3
-0.6
-12.9
-10.3
GAR1
GAR2
GAR3
3 Gain tracking vs. input level
CCITT G.714 Method 2
Units
Test Conditions
µ-Law
A-Law
Vp-p
Vp-p
0.95
-11.8
-9.1
dB
dB
dB
PCM to SPKR±
PCM to HSPKR±, RxA/u=0*
PCM to HSPKR±, RxA/u=1*
1020Hz
-0.15
-0.15
-0.15
+0.15
+0.15
+0.15
dB
dB
dB
PCM to SPKR±
PCM to HSPKR±, RxA/u=0*
PCM to HSPKR±, RxA/u=1*
from nominal
1020Hz
GTR
-0.3
-0.6
-1.6
0.3
0.6
1.6
dB
dB
dB
3 to -40 dBm0
-40 to -50 dBm0
-50 to -55 dBm0
4 Signal to total distortion vs. input
level
CCITT G.714 Method 2
GQR
35
29
24
dB
dB
dB
0 to -30dBm0
-40 dBm0
-45 dBm0
5 Receive Idle Channel Noise
NCR
NPR
6 Gain relative to gain at 1020 Hz
200 Hz
300-3000 Hz
3000-3400 Hz
4000 Hz
>4600 Hz
GRR
7 Absolute Delay
DAR
240
µs
at frequency of min. delay
8 Group Delay relative to DAR
DDR
750
380
130
750
µs
µs
µs
µs
500-600 Hz
600-1000 Hz
1000-2600 Hz
2600 - 2800 Hz
9 Crosstalk
CTRT
CTTR
dB
dB
G.714.16
All other receive filter settings
(-1 to -7 dB) are in addition to 0 dB
setting
D/A to A/D
A/D to D/A
0.2
-12.3
-9.7
-0.25
-0.90
15.5
-75
dBrnC0
dBrn0p
0.25
0.25
0.25
-12.5
-25
dB
dB
dB
dB
dB
-74
-80
µ-Law
A-Law
† AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
* Note: RxA/u, refer to General Control Register, address 0Fh.
AC Electrical Characteristics† for Side-tone Path
Sym.
Min.
Typ.‡
Max.
Units
Absolute path gain
Gain adjust = 0 dB
GAS1
GAS2
-17.213.1
-16.7
-12.6
16.2
-12.1
dB
dB
SIDEA/u, MICA/u, RxA/u all 0
SIDEA/u, MICA/u, RxA/u all 1
M± inputs to HSPKR± outputs
1000Hz
All other settings
(-9.96 to +9.96 dB)
GAS
GAS
-0.3
-0.3
+0.3
+0.3
dB
dB
SIDEA/u=0
SIDEA/u=1
from nominal
relative measurements w.r.t.
GAS1 & GAS2
Characteristics
1
Test Conditions
† AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
32
Zarlink Semiconductor Inc.
MT9094
Data Sheet
AC Electrical Characteristics† for New Call Tone
Characteristics
1
New Call Tone Output voltage
(SPKR+ to SPKR-)
Sym.
Typ.‡
Units
VNCT1
VNCT2
VNCT3
VNCT4
6.0
2.390
0.950
0.380
Vp-p
Vp-p
Vp-p
Vp-p
Test Conditions
NCTG0=0, NCTG1=0
NCTG0=1, NCTG1=0
NCTG0=0, NCTG1=1
NCTG0=1, NCTG1=1
load > 34 ohms across SPKR±
† AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
Electrical Characteristics† for Analog Outputs
Characteristics
Sym.
Min.
Typ.‡
260
300
ohms
300
pF
each pin:
%
300 ohms load across
HSPKR± (tol-15%),RxA/u=1,
VO≤693Vrms, Rx gain=0dB
1
Earpiece load impedance
EZL
2
Allowable Earpiece capacitive
load
ECL
3
Earpiece harmonic distortion
ED
4
Speaker load impedance
SZL
5
Allowable Speaker capacitive
load
SCL
6
Speaker harmonic distortion
SD
Max.
0.5
34
Units
Test Conditions
across HSPKR±
HSPKR+
HSPKR-
40
ohms
300
pF
each pin
%
40 ohms load across SPKR±
(tol-15%),
VO≤6.2Vp-p, Rx gain=0 dB
0.5
across SPKR±
SPKR+
SPKR-
† Electrical Characteristics are over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
Electrical Characteristics† for Analog Inputs
Characteristics
1
Differential input voltage without
overloading CODEC
2
Input impedance
Sym.
Min.
Typ.‡
VID
ZI
50
Max.
Units
Test Conditions
2.87
1.02
Vp-p
Vp-p
MICA/u=0, A/u=0
MICA/u=0, A/u=1
across MIC± or M± inputs,
Tx filter gain = 0 dB setting
kΩ
† Electrical Characteristics are over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
33
Zarlink Semiconductor Inc.
MIC+, MIC-, M+ or Mto VSS.
MT9094
Data Sheet
AC Electrical Characteristics† - ST-BUS Timing (See Figure 11)
Characteristics
Sym.
Min.
Typ.‡
Max.
Units
1
C4i Clock Period
tC4P
243
244
245
ns
2
C4i Clock High Period
tC4H
121
122
123
ns
3
C4i Clock Low Period
tC4L
121
122
123
ns
4
C4i Clock Transition Time
20
50
ns
5
F0i Frame Pulse Setup Time
tF0iS
50
ns
6
F0i Frame Pulse Hold Time
tF0iH
50
ns
7
F0i Frame Pulse Width Low
tF0iW
150
ns
8
DSTo Delay
tDSToD
9
DSTi Setup Time
tDSTiS
30
ns
10
DSTi Hold Time
tDSTiH
50
ns
tT
100
125
ns
Test Conditions
CL=50 pF
† Timing is over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
tT
tC4H
tC4P
C4i
tT
1 bit cell
2.4V
0.4V
tDSToD
DSTo
2.4V
0.4V
tDSTiS
DSTi
2.4V
0.4V
tT
F0i
tDSTiH
2.4V
0.4V
tF0iH
tF0iS
tT
tF0iW
Figure 11 - ST-BUS Timing Diagram
34
Zarlink Semiconductor Inc.
tC4L
MT9094
Data Sheet
AC Electrical Characteristics† - Microport Timing (see Figure 12)
Characteristics
Sym.
Min.
Typ.‡
Max.
Units
Test Conditions
1
Receive data setup
A
10
ns
2
Receive data hold
B
10
ns
3
Transmit data delay from clock falling
edge
C
80
ns
50 pF
4
High Z to valid data from SCLK
falling edge
D
80
ns
50 pF
5
Valid data to high Z from CS rising
edge
E
80
ns
50 pF
6
Current transmit data hold
from clock falling edge
F
0
ns
7
Chip Select to SCLK setup and hold
times
G
0
ns
8
SCLK clock period (3 MHz)
H
333
ns
† Timing is over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
DATA 1
RECEIVE
0
1
2
7
B
A
H
SCLK
G
G
CS
D
E
F
C
DATA 1 or DATA 2
TRANSMIT
0
1
2
6
Figure 12 - Serial Microport Timing Diagram
35
Zarlink Semiconductor Inc.
7
For more information about all Zarlink products
visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable.
However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such
information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or
use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual
property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in
certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink.
This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part
of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other
information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the
capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute
any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and
suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does
not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in
significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request.
Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system
conforms to the I2C Standard Specification as defined by Philips.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE