Maximum Ratings

20-1B12IPA008SC-L239C09
20-PB12IPA008SC-L239C09Y
target datasheet
flow IPM 1B (CI)
1200 V / 8 A
Features
flow 1B 17mm housing
Power
•
3 Phase Inverter
•
3 Phase Input Rectifier
•
Open Emitter or Emitter Shunt
Gate Driver
•
Booststrap circuit
•
Overcurrent protection
•
Undervoltage lockout
NTC
•
Temperature sensor
Solder pin variation
Press-fit pin variation
Schematic
Target applications
● Industrial motor drive
● Embedded Drive (fan, pump, compressor, etc.)
Types
● 20-1B12IPA008SC-L239C09
● 20-PB12IPA008SC-L239C09Y
Maximum Ratings
Tj=25°C, unless otherwise specified
Inverter Switch
Copyright Vincotech
1
22. May. 2015 / Revision 2
20-1B12IPA008SC-L239C09
20-PB12IPA008SC-L239C09Y
target datasheet
Inverter Diode
Gate driver
Inverter Shunt
Rectifier Diode
Copyright Vincotech
2
22. May. 2015 / Revision 2
20-1B12IPA008SC-L239C09
20-PB12IPA008SC-L239C09Y
target datasheet
Module Properties
Copyright Vincotech
3
22. May. 2015 / Revision 2
20-1B12IPA008SC-L239C09
20-PB12IPA008SC-L239C09Y
target datasheet
Characteristic Values
Inverter Switch
Inverter Diode
Copyright Vincotech
4
22. May. 2015 / Revision 2
20-1B12IPA008SC-L239C09
20-PB12IPA008SC-L239C09Y
target datasheet
Gate driver
Inverter Shunt
Copyright Vincotech
5
22. May. 2015 / Revision 2
20-1B12IPA008SC-L239C09
20-PB12IPA008SC-L239C09Y
target datasheet
Rectifier diode
Thermistor
Copyright Vincotech
6
22. May. 2015 / Revision 2
20-1B12IPA008SC-L239C09
20-PB12IPA008SC-L239C09Y
target datasheet
Ordering Code & Marking
Version
without thermal pas te 1 7 mm hous ing
w/o thermal pas te with P res s -fit pin 1 7 mm hous ing
NN-NNNNNNNNNN
NNNN-TTTTTTTVV
Vinco LLLLL
WWYY SSSS UL
Ordering Code
20-1B12IPA008SC-L239C09
20-PB12IPA008SC-L239C09Y
Text
Datamatrix
in DataMatrix as
L239C09
L239C09Y
in packaging barcode as
L239C09
L239C09Y
Name
Type&Ver
Date code
Vinco&Lot
Serial&UL
NN-NNNNNNNNNNNNNN
TTTTTTTVV
WWYY
Vinco LLLLL
SSSS UL
Type&Ver
Lot number
Serial
Date code
TTTTTTTVV
LLLLL
SSSS
WWYY
Outline
Pin table [mm]
Pin
X
Y
Function
1
45,1
0
W-HIN
2
42,4
0
W-LIN
3
39,7
0
RW+
4
37
0
RW-
5
34,3
0
GND
6
31,6
0
VCC
7
28,9
0
V-HIN
8
26,2
0
V-LIN
9
23,5
0
RV+
10
20,8
0
RV-
11
12
13
18,1
15,4
12,7
0
0
0
U-HIN
U-LIN
14
10
0
RU-
15
7,3
0
RESET
16
4,6
0
FAULT
17
1,9
0
NTC
18
0
8,8
L3
19
0
17,8
L2
20
3,8
26,1
L1
21
7,8
13,3
EU
22
9
18,7
DC1-
23
14,2
26,1
DC1+
24
20,6
17,8
EV
25
24,7
26,1
U
26
28,7
21,6
DC2+
27
36,2
16,7
EW
28
37,5
26,1
29
45,1
21,9
V
W
RU+
Pin Descriptions
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Function
W-HIN
W-LIN
RW+
RWGND
VCC
V-HIN
V-LIN
RV+
RVU-HIN
U-LIN
RU+
RURESET
¬FAULT
NTC
Copyright Vincotech
Description
Signal input for high-side W phase
Signal input for low-side W phase
W phase shunt +
W phase shunt Signal ground
Driver circuit supply voltage
Signal input for high-side V phase
Signal input for low-side V phase
V phase shunt +
V phase shunt Signal input for high-side U phase
Signal input for low-side U phase
U phase shunt +
U phase shunt Fault latch reset (min. 500ns pulse)
Fault latch input/output (negative logic, open drain)
Temperature sensor connector
7
Pin
18
19
20
21
22
23
24
25
26
27
28
29
Power pin descriptions
Function Description
L3
Rectifier input L3
L2
Rectifier input L2
L1
Rectifier input L1
EU
Open emitter U phase
DC1- Rectifier output DC+
DC1+ Rectifier output DCEV
Open emitter V phase
U
Output U phase
DC2+ Inverter input DC+
EW
Open emitter W phase
V
Output V phase
W
Output W phase
22. May. 2015 / Revision 2
20-1B12IPA008SC-L239C09
20-PB12IPA008SC-L239C09Y
target datasheet
Copyright Vincotech
8
22. May. 2015 / Revision 2
20-1B12IPA008SC-L239C09
20-PB12IPA008SC-L239C09Y
target datasheet
Document No.:
Date:
Modification:
Pages
20-1B12IPA008SC-L239C09 -T2-14
22 May. 2015
Press-fit variation
1, 7
Product status definition
Datasheet Status
Product Status
Target
Formative or In Design
Definition
This datasheet contains the design specifications for product development.
Specifications may change in any manner without notice. The data contained is
exclusively intended for technically trained staff.
DISCLAIMER
The information, specifications, procedures, methods and recommendations herein (together “information”) are presented by Vincotech to
reader in good faith, are believed to be accurate and reliable, but may well be incomplete and/or not applicable to all conditions or situations
that may exist or occur. Vincotech reserves the right to make any changes without further notice to any products to improve reliability,
function or design. No representation, guarantee or warranty is made to reader as to the accuracy, reliability or completeness of said
information or that the application or use of any of the same will avoid hazards, accidents, losses, damages or injury of any kind to persons
or property or that the same will not infringe third parties rights or give desired results. It is reader’s sole responsibility to test and determine
the suitability of the information and the product for reader’s intended use.
LIFE SUPPORT POLICY
Vincotech products are not authorised for use as critical components in life support devices or systems without the express written approval
of Vincotech.
As used herein:
1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or
sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in labelling can be
reasonably expected to result in significant injury to the user.
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause
the failure of the life support device or system, or to affect its safety or effectiveness.
Copyright Vincotech
9
22. May. 2015 / Revision 2