Si52147 Data Sheet

Si52147
PCI-E XPRESS G EN 1, G EN 2, & G EN 3 N IN E O UTPUT
C L O C K G ENERATOR
Features
Ordering Information:
See page 20.
Applications
Pin Assignments
43
42
41
SCLK
44
SDATA
XOUT
45
VDD_CORE
XIN/CLKIN
46
40
39
38
37
1
36 DIFF8
VDD_DIFF
2
35 DIFF8
OE_DIFF01
3
34 VDD_DIFF
OE_DIFF11
4
33 DIFF7
SSON2
5
VSS_DIFF
6
VSS_DIFF
7
OE_DIFF21
8
29 VSS_DIFF
OE_DIFF31
9
28 DIFF5
OE_DIFF[4:5]1 10
27 DIFF5
32 DIFF7
31 DIFF6
49
GND
30 DIFF6
26 DIFF4
OE_DIFF[6:8]1 11
25 DIFF4
13
14
15
16
17
18
19
20
21
22
23
24
DIFF2
DIFF3
DIFF3
VDD_DIFF
VSS_DIFF
12
DIFF2
VDD_DIFF
Functional Block Diagram
47
VDD_DIFF
DIFF1
The Si52147 is a high-performance, PCIe clock generator that can source nine
PCIe clocks from a 25 MHz crystal or clock input. The clock outputs are compliant
to PCIe Gen 1, Gen 2, and Gen 3 specifications. The device has six hardware
output enable control pins for enabling and disabling differential outputs. A spread
spectrum control pin for EMI reduction is also available. The small footprint and
low power consumption makes the Si52147 the ideal clock solution for consumer
and embedded applications.
48
NC
Description
NC
Wireless access point
 Servers
CKPWRGD/PDB1

VSS_CORE
Network attached storage
 Multi-function printer
DIFF1

VSS_DIFF

NC

VSS_DIFF

DIFF0

I2C support with readback
capabilities
Triangular spread spectrum
profile for maximum
electromagnetic interference
(EMI) reduction
Industrial temperature:
–40 to 85 oC
3.3 V power supply
 48-pin QFN package
NC

Up to nine PCI-Express clock
outputs
DIFF0

PCI-Express Gen 1, Gen 2, &

Gen 3 compliant
Supports Serial-ATA (SATA) at 
100 MHz
Low power push-pull HCSL

compatible differential outputs
No termination resistors required
Output enable pins for all clocks

Spread enable pin
25 MHz crystal input or clock
input

VDD_DIFF

Notes:
1. Internal 100 kohm pull-up.
2. Internal 100 kohm pull-down.
DIFF0
Patents pending
XIN/CLKIN
DIFF1
XOUT
DIFF2
DIFF3
PLL1
(SSC)
Divider
DIFF4
DIFF5
DIFF6
SCLK
SDATA
Control & Memory
DIFF7
CKPWRGD/PDB
Control
OE [8:0]
RAM
DIFF8
SSON
Rev. 1.2 2/14
Copyright © 2014 by Silicon Laboratories
Si52147
Si52147
2
Rev. 1.2
Si52147
TABLE O F C ONTENTS
Section
Page
1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.1. Crystal Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.2. CKPWRGD/PDB (Power Down) Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.3. PDB (Power Down) Assertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.4. PDB Deassertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.5. OE Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.6. OE Assertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.7. OE Deassertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.8. SSON Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3. Test and Measurement Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4. Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.1. I2C Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2. Data Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
5. Pin Descriptions: 48-Pin QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7. Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Rev. 1.2
3
Si52147
1. Electrical Specifications
Table 1. DC Electrical Specifications
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
3.3 V Operating Voltage
VDD core
3.3 ±5%
3.135
3.3
3.465
V
3.3 V Input High Voltage
VIH
Control input pins
2.0
—
VDD + 0.3
V
3.3 V Input Low Voltage
VIL
Control input pins
VSS – 0.3
—
0.8
V
Input High Voltage
VIHI2C
SDATA, SCLK
2.2
—
—
V
Input Low Voltage
VILI2C
SDATA, SCLK
—
—
1.0
V
Input High Leakage Current
IIH
Except internal pull-down
resistors, 0 < VIN < VDD
—
—
5
A
Input Low Leakage Current
IIL
Except internal pull-up
resistors, 0 < VIN < VDD
–5
—
—
A
High-impedance Output
Current
IOZ
–10
—
10
A
Input Pin Capacitance
CIN
1.5
—
5
pF
COUT
—
—
6
pF
LIN
—
—
7
nH
Power Down Current
IDD_PD
—
—
1
mA
Dynamic Supply Current
IDD_3.3V
—
—
85
mA
Output Pin Capacitance
Pin Inductance
4
All outputs enabled. Differential clocks with 5” traces
and 2 pF load.
Rev. 1.2
Si52147
Table 2. AC Electrical Specifications
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
LACC
Measured at VDD/2 differential
—
—
250
ppm
TDC
Measured at VDD/2
47
—
53
%
CLKIN Rise and Fall Times
TR/TF
Measured between 0.2 VDD and
0.8 VDD
0.5
—
4.0
V/ns
CLKIN Cycle to Cycle Jitter
TCCJ
Measured at VDD/2
—
—
250
ps
CLKIN Long Term Jitter
TLTJ
Measured at VDD/2
—
—
350
ps
Input High Voltage
VIH
XIN/CLKIN pin
2
—
VDD+0.3
V
Input Low Voltage
VIL
XIN/CLKIN pin
—
—
0.8
V
Input High Current
IIH
XIN/CLKIN pin, VIN = VDD
—
—
35
uA
Input Low Current
IIL
XIN/CLKIN pin, 0 < VIN <0.8
–35
—
—
uA
TDC
Measured at 0 V differential
45
—
55
%
TSKEW
Measured at 0 V differential
—
—
800
ps
Cycle to Cycle Jitter
TCCJ
Measured at 0 V differential
—
35
50
ps
PCIe Gen 1 Pk-Pk Jitter
Pk-Pk
PCIe Gen 1
0
40
50
ps
PCIe Gen 2 Phase Jitter
RMSGEN2
10 kHz < F < 1.5 MHz
0
1.8
2.0
ps
1.5 MHz < F < Nyquist
0
1.8
2.1
ps
RMSGEN3
Includes PLL BW 2–4 MHz,
CDR = 10 MHz
0
0.5
0.6
ps
Long Term Accuracy
LACC
Measured at 0 V differential
—
—
100
ppm
Rising/Falling Slew Rate
TR/TF
Measured differentially from
±150 mV
1
—
8
V/ns
Voltage High
VHIGH
—
—
1.15
V
Voltage Low
VLOW
–0.3
—
—
V
VOX
300
—
550
mV
—
–0.5
—
%
Crystal
Long-term Accuracy
Clock Input
CLKIN Duty Cycle
DIFF at 0.7 V
Duty Cycle
Output-to-Output skew
PCIe Gen 3 Phase Jitter
Crossing Point Voltage at
0.7 V Swing
Spread Range
SPR-2
Down spread
Modulation Frequency
FMOD
30
31.5
33
kHz
Clock Stabilization from
Power-up
TSTABLE
—
—
1.8
ms
Stopclock Set-up Time
TSS
10.0
—
—
ns
Enable/Disable and Setup
Note: Visit www.pcisig.com for complete PCIe specifications.
Rev. 1.2
5
Si52147
Table 3. Absolute Maximum Conditions
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
VDD_3.3V
Functional
—
—
4.6
V
Input Voltage
VIN
Relative to VSS
–0.5
—
4.6
VDC
Temperature, Storage
TS
Non-functional
–65
—
150
°C
Temperature, Operating Ambient
TA
Functional
–40
—
85
°C
Temperature, Junction
TJ
Functional
—
—
150
°C
Dissipation, Junction to Case
ØJC
JEDEC (JESD 51)
—
—
22
°C/W
Dissipation, Junction to Ambient
ØJA
JEDEC (JESD 51)
—
—
30
°C/W
ESDHBM
JEDEC (JESD 22-A114)
2000
—
—
V
UL-94
UL (Class)
Main Supply Voltage
ESD Protection (Human Body Model)
Flammability Rating
V–0
Note: While using multiple power supplies, the voltage on any input or I/O pin cannot exceed the power pin during power-up.
Power supply sequencing is not required.
6
Rev. 1.2
Si52147
2. Functional Description
2.1. Crystal Recommendations
If using crystal input, the device requires a parallel resonance 25 MHz crystal.
Table 4. Crystal Recommendations
Frequency
(Fund)
Cut
Loading Load Cap
25 MHz
AT
Parallel
12–15 pF
Shunt
Cap (max)
Motional
(max)
Tolerance
(max)
Stability
(max)
Aging
(max)
5 pF
0.016 pF
35 ppm
30 ppm
5 ppm
2.1.1. Crystal Loading
Crystal loading is critical in achieving low ppm performance. In order to achieve low/zero ppm error, use the
calculations in section 2.1.2 to estimate the appropriate capacitive loading (CL).
Figure 1 shows a typical crystal configuration using the two trim capacitors. It is important that the trim capacitors
are in series with the crystal.
Figure 1. Crystal Capacitive Clarification
2.1.2. Calculating Load Capacitors
In addition to the standard external trim capacitors, consider the trace capacitance and pin capacitance to calculate
the crystal loading correctly. The capacitance on each side is in series with the crystal. The total capacitance on
both sides is twice the specified crystal load capacitance (CL). Trim capacitors are calculated to provide equal
capacitive loading on both sides.
Figure 2. Crystal Loading Example
Use the following formulas to calculate the trim capacitor values for Ce1 and Ce2.
Rev. 1.2
7
Si52147
Load Capacitance (each side)
Ce = 2 x CL – (Cs + Ci)
Total Capacitance (as seen by the crystal)
CLe
=
1
1
( Ce1 + Cs1
+ Ci1 +
1
Ce2 + Cs2 + Ci2
)
CL:
Crystal load capacitance
CLe: Actual loading seen by crystal using standard value trim capacitors
Ce: External trim capacitors
Cs: Stray capacitance (terraced)
Ci : Internal capacitance (lead frame, bond wires, etc.)
2.2. CKPWRGD/PDB (Power Down) Pin
The CKPWRGD/PDB pin is a dual-function pin. During initial power up, the pin functions as the CKPWRGD pin.
Upon the first power up, if the CKPWRGD pin is low, the outputs will be disabled, but the crystal oscillator and I2C
logics will be active. Once the CKPWRGD pin has been sampled high by the clock chip, the pin assumes a PDB
functionality. When the pin has assumed a PDB functionality and is pulled low, the device will be placed in power
down mode. The CKPWRGD/PDB pin is required to be driven at all times even though it has an internal 100 k
resistor.
2.3. PDB (Power Down) Assertion
The PDB pin is an asynchronous active low input used to disable all output clocks in a glitch-free manner. All
outputs will be driven low in power down mode. In power down mode, all outputs, the crystal oscillator, and the I2C
logic are disabled.
2.4. PDB Deassertion
When a valid rising edge on CKPWRGD/PDB pin is applied, all outputs are enabled in a glitch-free manner within
two to six output clock cycles.
2.5. OE Pin
The OE pin is an active high input used to enable and disable the output clock. To enable the output clock, the OE
pin and the I2C OE bit need to be a logic high. By default, the OE pin and the I2C OE bit are set to a logic high.
There are two methods to disable the output clock: the OE pin is pulled to a logic low, or the I2C OE bit is set to a
logic low. The OE pin is required to be driven at all times even though it has an internal 100 k resistor.
2.6. OE Assertion
The OE pin is an active high input used for synchronous stopping and starting the respective output clock while the
rest of the clock generator continues to function. The assertion of the OE function is achieved by pulling the OE pin
and the I2C OE bit high which causes the respective stopped output to resume normal operation. No short or
stretched clock pulses are produced when the clocks resume. The maximum latency from the assertion to active
outputs is no more than two to six output clock cycles.
2.7. OE Deassertion
The OE function is deasserted by pulling the pin or the I2C OE bit to a logic low. The corresponding output is
stopped cleanly and the final output state is driven low.
2.8. SSON Pin
The SSON pin is an active input used to enable –0.5% spread spectrum on the outputs. When sampled high,
–0.5% spread is enabled on the output clocks. When sampled low, the output clocks are non-spread.
8
Rev. 1.2
Si52147
3. Test and Measurement Setup
Figure 3 shows the test load configuration for the HCSL compatible output clocks.
M e a s u re m e n t
P o in t
L1
O U T+
5 0
2 pF
L1 = 5"
M e a s u re m e n t
P o in t
L1
O U T-
5 0
2 pF
Figure 3. 0.7 V Differential Load Configuration
Please reference application note AN781 for recommendations on how to terminate the differential outputs for
LVDS, LVPECL, or CML signalling levels.
Figure 4. Differential Output Signals (for AC Parameters Measurement)
Rev. 1.2
9
Si52147
VMIN = –0.30V
VMIN = –0.30V
Figure 5. Single-ended Measurement for Differential Output Signals
(for AC Parameters Measurement)
10
Rev. 1.2
Si52147
4. Control Registers
4.1. I2C Interface
To enhance the flexibility and function of the clock synthesizer, an I2C interface is provided. Through the I2C
interface, various device functions are available, such as individual clock output enablement. The registers
associated with the I2C interface initialize to their default setting at power-up. The use of this interface is optional.
Clock device register changes are normally made at system initialization, if any are required.
4.2. Data Protocol
The clock driver I2C protocol accepts byte write, byte read, block write, and block read operations from the
controller. For block write/read operation, access the bytes in sequential order from lowest to highest (most
significant bit first) with the ability to stop after any complete byte is transferred. For byte write and byte read
operations, the system controller can access individually indexed bytes.
The block write and block read protocol is outlined in Table 5 while Table 6 outlines byte write and byte read
protocol. The slave receiver address is 11010110 (D6h).
Table 5. Block Read and Block Write Protocol
Block Write Protocol
Bit
1
8:2
Block Read Protocol
Description
Bit
Start
1
Slave address—7 bits
8:2
Description
Start
Slave address–7 bits
9
Write
9
Write
10
Acknowledge from slave
10
Acknowledge from slave
18:11
Command Code—8 bits
18:11
19
Acknowledge from slave
19
Acknowledge from slave
Byte Count—8 bits
20
Repeat start
27:20
28
36:29
37
45:38
Acknowledge from slave
27:21
Command Code–8 bits
Slave address–7 bits
Data byte 1–8 bits
28
Read = 1
Acknowledge from slave
29
Acknowledge from slave
Data byte 2–8 bits
46
Acknowledge from slave
....
Data Byte/Slave Acknowledges
....
Data Byte N–8 bits
....
Acknowledge from slave
....
Stop
37:30
38
46:39
47
55:48
Rev. 1.2
Byte Count from slave–8 bits
Acknowledge
Data byte 1 from slave–8 bits
Acknowledge
Data byte 2 from slave–8 bits
56
Acknowledge
....
Data bytes from slave/Acknowledge
....
Data Byte N from slave–8 bits
....
NOT Acknowledge
....
Stop
11
Si52147
Table 6. Byte Read and Byte Write Protocol
Byte Write Protocol
Bit
1
8:2
Byte Read Protocol
Description
Bit
Start
1
Slave address–7 bits
8:2
Start
Slave address–7 bits
9
Write
9
Write
10
Acknowledge from slave
10
Acknowledge from slave
18:11
19
27:20
Command Code–8 bits
18:11
Command Code–8 bits
Acknowledge from slave
19
Acknowledge from slave
Data byte–8 bits
20
Repeated start
28
Acknowledge from slave
29
Stop
27:21
Rev. 1.2
Slave address–7 bits
28
Read
29
Acknowledge from slave
37:30
12
Description
Data from slave–8 bits
38
NOT Acknowledge
39
Stop
Si52147
Control Register 0. Byte 0
Bit
D7
D6
D5
D4
D3
D2
D1
D0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
D2
D1
D0
DIFF1_OE
DIFF2_OE
DIFF3_OE
R/W
R/W
R/W
Name
Type
Reset settings = 00000000
Bit
Name
7:0
Reserved
Function
Control Register 1. Byte 1
Bit
D7
D6
D5
Name
Type
D4
D3
DIFF0_OE
R/W
R/W
R/W
R/W
R/W
Reset settings = 00010111
Bit
Name
7:5
Reserved
4
DIFF0_OE
Function
Output Enable for DIFF0.
0: Output disabled.
1: Output enabled.
3
Reserved
2
DIFF1_OE
Output Enable for DIFF1.
0: Output disabled.
1: Output enabled.
1
DIFF2_OE
Output Enable for DIFF2.
0: Output disabled.
1: Output enabled.
0
DIFF3_OE
Output Enable for DIFF3.
0: Output disabled.
1: Output enabled.
Rev. 1.2
13
Si52147
Control Register 2. Byte 2
Bit
D7
D6
D5
D4
D3
Name
DIFF4_OE
DIFF5_OE
DIFF6_OE
DIFF7_OE
DIFF8_OE
Type
R/W
R/W
R/W
R/W
R/W
Reset settings = 11111000
Bit
Name
7
DIFF4_OE
Function
Output Enable for DIFF4.
0: Output disabled.
1: Output enabled.
6
DIFF5_OE
Output Enable for DIFF5.
0: Output disabled.
1: Output enabled.
5
DIFF6_OE
Output Enable for DIFF6.
0: Output disabled.
1: Output enabled.
4
DIFF7_OE
Output Enable for DIFF7.
0: Output disabled.
1: Output enabled.
3
DIFF8_OE
Output Enable for DIFF8.
0: Output disabled.
1: Output enabled.
2:0
14
Reserved
Rev. 1.2
D2
D1
D0
R/W
R/W
R/W
Si52147
Control Register 3. Byte 3
Bit
D7
D6
Name
Type
D5
D4
D3
Rev Code[3:0]
R/W
R/W
R/W
D2
D1
D0
Vendor ID[3:0]
R/W
R/W
R/W
R/W
R/W
D3
D2
D1
D0
R/W
R/W
R/W
R/W
Reset settings = 00001000
Bit
Name
Function
7:4
Rev Code[3:0]
Program Revision Code.
3:0
Vendor ID[3:0]
Vendor Identification Code.
Control Register 4. Byte 4
Bit
D7
D6
D5
D4
Name
Type
BC[7:0]
R/W
R/W
R/W
R/W
Reset settings = 00000110
Bit
Name
7:0
BC[7:0]
Function
Byte Count Register.
Rev. 1.2
15
Si52147
Control Register 5. Byte 5
Bit
D7
D6
D5
D4
D3
D2
D1
D0
R/W
R/W
R/W
R/W
Name DIFF_Amp_Sel DIFF_Amp_Cntl[2] DIFF_Amp_Cntl[1] DIFF_Amp_Cntl[0]
Type
R/W
R/W
R/W
R/W
Reset settings = 11011000
Bit
Name
7
DIFF_Amp_Sel
Function
Amplitude Control for DIFF Differential Outputs.
0: Differential outputs with Default amplitude.
1: Differential outputs amplitude is set by Byte 5[6:4].
16
6
DIFF_Amp_Cntl[2]
5
DIFF_Amp_Cntl[1]
4
DIFF_Amp_Cntl[0]
3:0
Reserved
DIFF Differential Outputs Amplitude Adjustment.
000: 300 mV 001: 400 mV 010: 500 mV
100: 700 mV 101: 800 mV 110: 900 mV
Rev. 1.2
011: 600 mV
111: 1000 mV
Si52147
NC
NC
VSS_DIFF
VSS_CORE
NC
NC
XIN/CLKIN
XOUT
VDD_CORE
CKPWRGD/PDB1
SDATA
SCLK
5. Pin Descriptions: 48-Pin QFN
48
47
46
45
44
43
42
41
40
39
38
37
VDD_DIFF
1
36
DIFF8
VDD_DIFF
2
35
DIFF8
OE_DIFF0 1
3
34
VDD_DIFF
OE_DIFF1 1
4
33
DIFF7
SSON 2
5
32
DIFF7
VSS_DIFF
6
31
DIFF6
VSS_DIFF
7
30
DIFF6
OE_DIFF2 1
8
29
VSS_DIFF
OE_DIFF3 1
9
28
DIFF5
OE_DIFF[4:5]1
10
27
DIFF5
OE_DIFF[6:8]1
11
26
DIFF4
VDD_DIFF
12
49
GND
17
18
19
20
21
VSS_DIFF
DIFF1
DIFF1
DIFF2
DIFF2
DIFF3
22
23
24
VSS_DIFF
16
VDD_DIFF
15
DIFF3
14
DIFF0
VDD_DIFF
13
DIFF0
25 DIFF4
Notes:
1. Internal 100 kohm pull-up.
2. Internal 100 kohm pull-down.
.
Table 7. Si 52147 48-Pin QFN Descriptions
Pin #
Name
Type
Description
1
VDD_DIFF
PWR 3.3 V Power Supply
2
VDD_DIFF
PWR 3.3 V Power Supply
3
OE_DIFF0
I,PU
Active high input pin enables DIFF0 (internal 100 k pull-up).
4
OE_DIFF1
I,PU
Active high input pin enables DIFF1 (internal 100 k pull-up).
5
SSON
I, PD
Active high input pin enables –0.5% spread on DIFF clocks (internal
100 k pull-down)
6
VSS_DIFF
GND
Ground
7
VSS_DIFF
GND
Ground
Rev. 1.2
17
Si52147
Table 7. Si 52147 48-Pin QFN Descriptions (Continued)
Pin #
Name
Type
8
OE_DIFF2
I,PU
Active high input pin enables DIFF2 (internal 100 k pull-up).
9
OE_DIFF3
I,PU
Active high input pin enables DIFF3 (internal 100 k pull-up).
10
OE_DIFF[4:5]
I,PU
Active high input pin enables DIFF[4:5] (internal 100 k pull-up).
11
OE_DIFF[6:8]
I,PU
Active high input pin enables DIFF[6:8] (internal 100 k pull-up).
12
VDD_DIFF
PWR 3.3 V Power Supply
13
VDD_DIFF
PWR 3.3 V Power Supply
14
DIFF0
O, DIF 0.7 V, 100 MHz differential clock output
15
DIFF0
O, DIF 0.7 V, 100 MHz differential clock output
16
VSS_DIFF
17
DIFF1
O, DIF 0.7 V, 100 MHz differential clock output
18
DIFF1
O, DIF 0.7 V, 100 MHz differential clock output
19
DIFF2
O, DIF 0.7 V, 100 MHz differential clock output
20
DIFF2
O, DIF 0.7 V, 100 MHz differential clock output
21
DIFF3
O, DIF 0.7 V, 100 MHz differential clock output
22
DIFF3
O, DIF 0.7 V, 100 MHz differential clock output
23
VDD_DIFF
PWR 3.3V Power Supply
24
VSS_DIFF
GND
25
DIFF4
O, DIF 0.7 V, 100 MHz differential clock output
26
DIFF4
O, DIF 0.7 V, 100 MHz differential clock output
27
DIFF5
O, DIF 0.7 V, 100 MHz differential clock output
28
DIFF5
O, DIF 0.7 V, 100 MHz differential clock output
29
VSS_DIFF
30
DIFF6
O, DIF 0.7 V, 100 MHz differential clock output
31
DIFF6
O, DIF 0.7 V, 100 MHz differential clock output
32
DIFF7
O, DIF 0.7 V, 100 MHz differential clock output
33
DIFF7
O, DIF 0.7 V, 100 MHz differential clock output
34
VDD_DIFF
35
DIFF8
O, DIF 0.7 V, 100 MHz differential clock output
36
DIFF8
O, DIF 0.7 V, 100 MHz differential clock output
18
GND
GND
Description
Ground
Ground
Ground
PWR 3.3 V Power Supply
Rev. 1.2
Si52147
Table 7. Si 52147 48-Pin QFN Descriptions (Continued)
Pin #
Name
Type
Description
2
37
SCLK
I
I C compatible SCLOCK
38
SDATA
I/O
39
CKPWRGD/PDB
I, PU
40
VDD_CORE
41
XOUT
O
25.00 MHz crystal output, Float XOUT if using only CLKIN (Clock input).
42
XIN/CLKIN
I
25.00 MHz crystal input or 3.3 V, 25 MHz Clock Input.
43
NC
NC
No Connect
44
NC
NC
No Connect
45
VSS_CORE
GND
Ground
46
VSS_DIFF
GND
Ground
47
NC
NC
No Connect
48
NC
NC
No Connect
49
GND
GND
I2C compatible SDATA
Active low input pin asserts power down (PDB) and disables all outputs
(internal 100 k pull-up).
PWR 3.3 V Power Supply
Ground for bottom pad of the IC.
Rev. 1.2
19
Si52147
6. Ordering Guide
Part Number
Package Type
Temperature
Si52147-A01AGM
48-pin QFN
Industrial, –40 to 85 C
Si52147-A01AGMR
48-pin QFN—Tape and Reel
Industrial, –40 to 85 C
Lead-free
20
Rev. 1.2
Si52147
7. Package Outline
Figure 6 illustrates the package details for the Si52147. Table 8 lists the values for the dimensions shown in the
illustration.
Figure 6. 48-Pin Quad Flat No Lead (QFN) Package
Table 8. Package Diagram Dimensions
Symbol
Millimeters
Min
Nom
Max
0.70
0.75
0.80
A1
0.00
0.025
0.05
b
0.15
0.20
0.25
A
D
D2
6.00 BSC
4.30
4.40
e
0.40 BSC
E
6.00 BSC
4.50
E2
4.30
4.40
4.50
L
0.30
0.40
0.50
aaa
0.10
bbb
0.10
ccc
0.08
ddd
0.07
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise
noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to JEDEC outline MO-220, variation VGGD-8.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020
specification for Small Body Components.
Rev. 1.2
21
Si52147
DOCUMENT CHANGE LIST
Revision 0.1 to Revision 1.0







Updated pinout.
Updated Table 2.
Updated section 2.1.
Updated section 2.1.1.
Updated sections 2.2 through 2.8.
Updated section 4.2.
Updated Table 7.
Revision 1.0 to Revision 1.1

Removed Moisture Sensitivity Level specification
from Table 3.
Revision 1.1 to Revision 1.2


22
Updated Table 2.
Updated Section 3.
Rev. 1.2
Si52147
NOTES:
Rev. 1.2
23
Si52147
CONTACT INFORMATION
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
Tel: 1+(512) 416-8500
Fax: 1+(512) 416-9669
Toll Free: 1+(877) 444-3032
Please visit the Silicon Labs Technical Support web page:
https://www.silabs.com/support/pages/contacttechnicalsupport.aspx
and register to submit a technical support request.
Patent Notice
Silicon Labs invests in research and development to help our customers differentiate in the market with innovative low-power, small size, analogintensive mixed-signal solutions. Silicon Labs' extensive patent portfolio is a testament to our unique approach and world-class engineering team.
The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice.
Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from
the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features
or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to
support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages.
Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc.
Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders.
24
Rev. 1.2