Si5356A I 2C P ROGRAMMABLE , A NY - F R E Q U E N C Y 1 – 2 0 0 M H Z , Q UAD F R E Q U E N C Y 8-O UTPUT C LOCK G ENERATOR Features Generates any frequency from 1 to 200 MHz on each of the 4 output banks Programmable frequency configuration Guaranteed 0 ppm frequency synthesis error for any combination of frequencies 25 or 27 MHz xtal or 5–200 MHz input clk Eight CMOS clock outputs Easy to use programming software Configurable “triple A” spread spectrum: any clock, any frequency, and with any spread amount Programmable output phase adjustment with <20 ps error Interrupt pin indicates LOS or LOL OEB pin disables all outputs or per bank OEB control via I2C Low jitter: 50 ps pk-pk (typ), 75 ps pk-pk period jitter (max) Excellent PSRR performance eliminates need for external power supply filtering Low power: 45 mA (core) Core VDD: 1.8, 2.5, or 3.3 V Separate VDDO for each bank of outputs: 1.8, 2.5, or 3.3 V Small size: 4x4 mm 24-QFN Industrial temperature range: –40 to +85 °C Ordering Information: See page 23. Pin Assignments Applications CLK1 CLK1 VDDOA VDDOA P3 SDA Top TopView View Storage area networks Switches/routers Servers CLK0 CLK0 24 24 2323 2222 2121 20 20 19 19 GND GND Printers Audio/video DSLAM VDD VDD Description XAXA1 1 18 18 CLK2 CLK2 The Si5356 is a highly flexible, I2C programmable clock generator capable of synthesizing four completely non-integer related frequencies up to 200 MHz. The device has four banks of outputs with each bank supporting two CMOS outputs at the same frequency. Using Silicon Laboratories' patented MultiSynth fractional divider technology, all outputs are guaranteed to have 0 ppm frequency synthesis error regardless of configuration, enabling the replacement of multiple clock ICs and crystal oscillators with a single device. Each output bank is independently configurable to support 1.8, 2.5, or 3.3 V. The device is programmable via an I2C/ SMBus-compatible serial interface and supports operation from a 1.8, 2.5, or 3.3 V core supply. XBXB2 2 17 17 CLK3 CLK3 16 16 VDDOB VDDOB I2C_LSB P1 3 3 GND GND GND GND CLKIN CLKIN4 4 15 15 VDDOC VDDOC 14 14 CLK4 CLK4 SSC_DIS P4 5 5 LOS INTR CLK7 CLK7 1010 11 11 12 12 P2 SCL 99 CLK6 CLK6 8 8 VDDOD VDDOD 7 7 VDD VDD OEB6 6 P5 13 13 CLK5 CLK5 Functional Block Diagram Rev. 1.3 Copyright © 2014 by Silicon Laboratories Si5356A Si5356A 2 Rev. 1.3 Si5356A TABLE O F C ONTENTS Section Page 1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2. Typical Application Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3.2. Input Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.3. Breakthrough MultiSynth Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.4. Frequency Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.5. Configuring the Si5356 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.6. Output Phase Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.7. CMOS Output Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.8. Jitter Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.9. Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.10. I2C Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.11. Spread Spectrum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 3.12. Power Supply Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4. Si5356 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 5. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 6. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 6.1. Evaluation Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 7. Package Outline: 24-Lead QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 8. Recommended PCB Land Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 9. Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 9.1. Si5356A Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 9.2. Top Marking Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 10. Device Errata . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Rev. 1.3 3 Si5356A 1. Electrical Specifications Table 1. Recommended Operating Conditions (VDD = 1.8 V –5% to +10%, 2.5 or 3.3 V ±10%, TA = –40 to 85 °C) Parameter Symbol Test Condition Min Typ Max Ambient Temperature TA –40 — 85 Core Supply Voltage VDD 2.97 3.3 3.63 2.25 2.5 2.75 1.71 1.8 1.98 1.71 — 3.63 Output Buffer Supply Voltage VDDO Unit o C V V Note: All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions. Typical values apply at nominal supply voltages and an operating temperature of 25 °C unless otherwise noted. Table 2. DC Characteristics (VDD = 1.8 V –5% to +10%, 2.5 or 3.3 V ±10%, TA = –40 to 85 °C) Parameter Core Supply Current Output Buffer Supply Current High Level Input Voltage Low Level Input Voltage Symbol Test Condition Min Typ Max Unit IDD 100 MHz on all outputs, 25 MHz refclk — 45 60 mA IDDOx CMOS, 50 MHz 15 pF load — 6 9 mA CMOS, 200 MHz 3.3 V VDD0 — 13 18 mA CMOS, 200 MHz 2.5 V — 10 14 mA CMOS, 200 MHz 1.8 V — 7 10 mA CLKIN, I2C_LSB 0.8 x VDD — 3.63 V SSC_DIS, OEB 0.85 — 1.3 V CLKIN, I2C_LSB –0.2 — 0.2 x VDD V SSC_DIS, OEB — — 0.3 V VIH VIL Clock Output High Level Output Voltage VOH Pins: CLK0–7 IOH = –4 mA VDDO – 0.3 — — V Clock Output Low Level Output Voltage VOL Pins: CLK0–7 IOL = +4 mA — — 0.3 V VOLINTR Pin: INTR IOL = +3 mA 0 — 0.4 V — 20 — k INTR Low Level Output Voltage SSC_DIS, OEB Input Resistance 4 RIN Rev. 1.3 Si5356A Table 3. AC Characteristics (VDD = 1.8 V –5% to +10%, 2.5 or 3.3 V ±10%, TA = –40 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit 5 — 200 MHz 20–80% VDD — — 2.3 ns 10–90% VDD — — 4 ns Input tr/tf within specified limits shown above 40 — 60 % Input Clock Clock Input Frequency Clock Input Rise/Fall Time FIN TR/TF Clock Input Duty Cycle DC Clock Input Capacitance CIN — 2 — pF FO 1 — 200 MHz 0 0 1 ppb — — 15 pF Output Clocks Clock Output Frequency Clock Output Frequency Synthesis Resolution Output Load Capacitance FRES See "3.4. Frequency Configuration" on page 11 CL Clock Output Rise/Fall Time TR/TF 20 to 80% VDD, CL = 15 pF — — 2.0 ns Clock Output Rise/Fall Time TR/TF 20 to 80% VDD, CL = 2 pF — 0.45 0.85 ns Clock Output Duty Cycle DC Measured at VDD/2 45 50 55 % Powerup Time TPU POR to output clock valid — — 2 ms Output Enable Time TOE — — 10 µs Output-Output Skew TSKEW Outputs at same frequency, fOUT > 5 MHz –150 — +150 ps Period Jitter JPPKPK 10000 cycles* — 50 75 ps pk-pk Cycle-Cycle Jitter JCCPK 10000 cycles* — 40 70 ps pk Phase Jitter JPH 12 kHz to 20 MHz — 2 — ps rms PLL Loop Bandwidth FBW — 1.6 — MHz tLOS — 2.6 5 µs tLOS_b 0.01 0.2 1 µs Interrupt Status Timing CLKIN Loss of Signal Assert Time CLKIN Loss of Signal Deassert Time *Note: Measured in accordance to JEDEC Standard 65. Rev. 1.3 5 Si5356A Table 4. Crystal Specifications Parameter Crystal Frequency Load Capacitance (on-chip differential) Crystal Output Capacitance Equivalent Series Resistance Symbol Test Condition Min Typ Max Unit FXTAL Option 1 — 25 — MHz Option 2 — 27 — MHz cL (supported)* 11 12 13 pF cL (recommended) 17 18 19 pF CO — — 5 pF 25 MHz — — 100 27 MHz — — 75 100 — — µW ESR Crystal Drive Level Rating dL *Note: See "AN360: Crystal Selection Guide for Si533x and Si5355/56 Devices" for how to adjust the registers to accommodate a 12 pF crystal CL Table 5. I2C Specifications (SCL,SDA)1 Parameter Symbol Test Condition Standard Mode Fast Mode Unit Min Max Min Max LOW level input voltage VILI2C –0.5 0.3 x VDDI2C –0.5 0.3 x VDDI2C2 V HIGH level input voltage VIHI2C 0.7 x VDDI2C 3.63 0.7 x VDDI2C2 3.63 V Hysteresis of Schmitt trigger inputs VHYS N/A N/A 0.1 — V VDDI2C2 = 2.5/3.3 V 0 0.4 0 0.4 V 2 N/A N/A 0 0.2 x VDDI2C V –10 10 –10 10 µA — 4 — 4 pF 25 35 25 35 ms LOW level output voltage (open drain or open collector) at 3 mA sink current VOLI2C2 VDDI2C = 1.8 V Input current III2C Capacitance for each I/O pin CII2C I2C Bus timeout — VIN = –0.1 to VDDI2C Notes: 1. Refer to NXP’s UM10204 I2C-bus specification and user manual, revision 03, for further details. 2. Only I2C pull up voltages (VDDI2C) of 1.71 to 3.63 V are supported. Must write register 27[7] = 1 if the I2C bus voltage is less than 2.25 V. 6 Rev. 1.3 Si5356A Table 6. Thermal Conditions Parameter Symbol Test Condition Value Unit Thermal Resistance Junction to Ambient JA Still Air 37 °C/W Thermal Resistance Junction to Case JC Still Air 25 °C/W Table 7. Absolute Maximum Ratings1,2,3,4 Parameter Symbol Rating Unit VDD –0.5 to +3.8 V Input Voltage Range (all pins except pins 1,2,5,6) VI –0.5 to 3.8 V Input Voltage Range (pins 1,2,5,6) VI2 –0.5 to 1.3 V Output Voltage Range VO –0.5 to VDD + 0.3 V Junction Temperature TJ –55 to +150 HBM 2.5 kV CDM 550 V MM 175 V Supply Voltage Range ESD Tolerance Latch-up Tolerance LU 5 Soldering Temperature (Pb-free profile) C JESD78 Compliant TPEAK 260 TP 20–40 Soldering Temperature Time at TPEAK (Pb-free profile)5 o o C sec Notes: 1. Permanent device damage may occur if the Absolute Maximum Ratings are exceeded. Functional operation should be restricted to the conditions as specified in the operational sections of this data sheet. Exposure to maximum rating conditions for extended periods may affect device reliability. 2. 24-QFN package is RoHS compliant. 3. For more packaging information, go to www.silabs.com/support/quality/pages/RoHSInformation.aspx. 4. Moisture sensitivity level is MSL3. 5. The device is compliant with JEDEC J-STD-020. Rev. 1.3 7 Si5356A 2. Typical Application Circuits +3.3 V 0.1 uF Power Supply Decoupling Capacitors (1 per VDD or VDDOx pin) 4-Port Ethernet Switch/Router 1 2 4 +3.3V VDDOD VDDOB VDD CLK0 CLKIN CLK1 1k CLK2 8 19 I2C Bus 12 3 I C Address = 111 0000 (0x70) or 111 0001 (0x71) 2 Rse 5 Rse 6 Note: See section 3.2 for information on selecting Rse and Rsh. XB Rsh CLK3 INTR CLK4 Si5356 SDA CLK5 SCL CLK6 I2C_LSB CLK7 22 25 MHz 25 MHz 25 MHz 25 MHz 21 18 17 14 13 10 9 x x 125 MHz 33/66 MHz MCU/ Processor SSC_DIS OEB Rsh Ethernet Ethernet PHY Ethernet PHY Ethernet PHY PHY Ethernet Switch GND 1k XA GND 1k 15 11 VDDOC 25 MHz XTAL 20 16 VDDOA VDD 7 24 PAD PAD 23 23 Laser Printer +3.3 V 0.1 uF Power Supply Decoupling Capacitors (1 per VDD or VDDOx pin) Ethernet PHY 1 2 4 +3.3 V 1k 1k 125 MHz XB CLK0 CLKIN CLK1 CLK2 8 19 I C Bus 12 2 I C Address = 111 0000 (0x70) or 111 0001 (0x71) 3 CLK3 INTR Si5356 SDA DDR Memory VDDOD VDDOB XA 1k 2 Processor 15 11 VDDOC VDDOA 25 MHz XTAL 20 16 VDD VDD 7 24 USB Controller CLK4 CLK5 SCL CLK6 I2C_LSB CLK7 Print Head 22 21 18 17 14 13 10 9 x 48 MHz Paper Tray x 66/100 MHz x Key Pad x 35.788 MHz 8 Rse 6 Rsh Rsh SSC_DIS Touchscreen Controller OEB 23 23 GND 5 GND Note: See section 3.2 for information on selecting Rse and Rsh. Rse PAD PAD Rev. 1.3 LCD Screen Si5356A 3. Functional Description 3.1. Overview 3.1.1. ClockBuilder™ Desktop Software I 2C The Si5356 is a highly flexible, programmable clock generator capable of synthesizing four independent frequencies up to 200 MHz. The device has four banks of outputs with each bank supporting two CMOS outputs at the same frequency. The Si5356 supports free-running mode of operation using an external crystal, or it can lock to an external clock for generating synchronous clocks. The output drivers support 1.8, 2.5, and 3.3 V CMOS formats, and each output bank is independently configurable. Adjustable output-to-output phase offsets are also available to compensate for PCB trace delays or for fine tuning of setup and hold margins. Configuration and control of the Si5356 is handled through the I2C/SMBus interface. The device also provides the option of storing a user-definable clock configuration in its non-volatile memory (NVM), which becomes the default clock configuration power-up. See section "3.5.1. Ordering a Custom NVM Configuration" on page 12 for details. To simplify device configuration, Silicon Labs has released the ClockBuilder Desktop. The software serves two purposes: to configure the Si5356 with optimal configuration based on the desired frequencies, and to control the EVB, when connected to a host PC. The optimal configuration can be saved from the software in text files that can be used in any system, which configures the device over I2C. ClockBuilder Desktop can be downloaded from www.silabs.com/ ClockBuilder and runs on Windows XP, Windows Vista, and Windows 7. Additionally, an NVM file can be generated using the NVMSave for Factory Programming... menu option. An NVM file can be used by factory to prepare custom pre-programmed devices. Rev. 1.3 9 Si5356A 3.2. Input Configuration The Si5356 input can be driven from either an external crystal or a reference clock. If the crystal input option is used, the Si5356 operates as a free-running clock generator. In this mode of operation the device requires a low cost 25 or 27 MHz fundamental mode crystal connected across XA and XB as shown in Figure 1. Given the Si5356’s frequency flexibility, the same crystal can be reused to generate any combination of output frequencies. Custom frequency crystals are not required. The Si5356 integrates the crystal load capacitors on-chip to reduce external component count. The crystal should be placed very close to the device to minimize stray capacitance. To ensure a stable and accurate output frequency, the recommended crystal specifications provided in Table 4 on page 6 must be followed. See AN360 for additional details regarding crystal recommendations. Si5356 XTAL XA XB Figure 1. Connecting an XTAL to the Si5356 For synchronous timing applications, the Si5356 can lock to a 5 to 200 MHz CMOS reference clock. A typical interface circuit is shown in Figure 2. A series termination resistor matching the driver’s output impedance to the impedance of the transmission line is recommended to reduce reflections. Si5356 Rs 50 CLKIN CMOS Level 1.8 V 2.5 V 3.3 V RSH ohms 1580 1580 1580 3.3. Breakthrough MultiSynth Technology Modern timing architectures require a wide range of frequencies which are often non-integer related. Traditional clock architectures address this by using a combination of single PLL ICs, 4-PLL ICs and discrete XOs, often at the expense of BOM complexity and power. The Si5356 use patented MultiSynth technology to dramatically simplify timing architectures by integrating the frequency synthesis capability of 4 phase-locked loops (PLLs) in a single device, greatly minimizing size and power requirements versus traditional solutions. Based on a fractional-N PLL, the heart of the architecture is a low phase noise, highfrequency VCO. The VCO supplies a high frequency output clock to the MultiSynth block on each of the four independent output paths. Each MultiSynth operates as a high-speed fractional divider with Silicon Laboratories' proprietary phase error correction to divide down the VCO clock to the required output frequency with very low jitter. The first stage of the MultiSynth architecture is a fractional-N divider which switches seamlessly between the two closest integer divider values to produce the exact output clock frequency with 0 ppm error. To eliminate phase error generated by this process, MultiSynth calculates the relative phase difference between the clock produced by the fractional-N divider and the desired output clock and dynamically adjusts the phase to match the ideal clock waveform. This novel approach makes it possible to generate any output clock frequency without sacrificing jitter performance. Based on this architecture, each clock output can produce any frequency from 1 to 200 MHz. Figure 2. Interfacing CMOS Reference Clocks to the Si5356 Control input signals to SSC_DIS and OEB cannot exceed 1.3 V yet also need to meet the VOH and VOL specifications outlined in Table 2 on page 4. When these inputs are driven from CMOS sources, a resistive attenuator as shown in the Typical Application Circuits must be used. Suggested standard 1% resistor values for RSE and RSH, when using a CMOS source, are given below. 10 RSE ohms 1000 1960 3090 Rev. 1.3 Si5356A MultiSynth Fractional-N Divider fVCO Phase Adjust fOUT Phase Error Calculator Divider Select (DIV1, DIV2) Figure 3. Silicon Labs' MultiSynth Technology 3.4. Frequency Configuration Power-Up/POR The Si5356 utilizes a single PLL-based architecture, four independent MultiSynth fractional output dividers, and a MultiSynth fractional feedback divider such that a single device provides the clock generation capability of four independent PLLs. Unlike competitive multi-PLL solutions, the Si5356 can generate four unique noninteger related output frequencies with 0 ppm frequency error, with respect to the reference, for any combination of output frequencies. In addition, any combination of output frequencies can be generated from a single reference frequency without having to change the crystal or reference clock frequency between configurations. Frequency configurations are fully programmable by writing to device registers using the I2C interface. Any combination of output frequencies ranging from 1 to 200 MHz can be configured on each of the device outputs. 3.5. Configuring the Si5356 The Si5356 is a highly-flexible clock generator that is entirely configurable through its I2C interface. The device’s default configuration is stored in non-volatile memory (NVM) as shown in Figure 4. The NVM is a one-time programmable memory (OTP), which can store a custom user configuration at power-up. This is a useful feature for applications that need a clock present at power-up (e.g., for providing a clock to a processor). NVM (OTP) Default Config RAM I2C Figure 4. Si5356 Memory Configuration During a power cycle or a power-on reset (POR), the contents of the NVM are copied into random access memory (RAM), which sets the device configuration that will be used during operation. Any changes to the device configuration after power-up are made by reading and writing to registers in the RAM space through the I2C interface. ClockBuilder Desktop (see "3.1.1. ClockBuilder™ Desktop Software" on page 9) can be used to easily configure register map files that can be written into RAM (see “3.5.2. Creating a New Configuration for RAM” for details). Alternatively, the register map file can be created manually with the help of the equations in AN565. Two versions of the Si5356 are available. First, noncustomized Si5356 devices are available in which the RAM can be configured in-circuit via I2C. These blank Si5356 devices can also be field programmed using the Si5338/56-PROG-EVB (see “3.5.4. Writing a Custom Configuration to NVM”). Second, custom factoryprogrammed Si5356 devices are available that include a user-specified startup frequency configuration (example part number Si5356A-Axxxxx-GM). Rev. 1.3 11 Si5356A 3.5.1. Ordering a Custom NVM Configuration 3.5.3. Writing a Custom Configuration to RAM The Si5356 is orderable with a factory-programmed custom NVM configuration. This is the simplest way of using the Si5356 since it generates the desired output frequencies at power-up or after a power-on reset (POR). This default configuration can be reconfigured in RAM through the I2C interface after power-up (see “3.5.2. Creating a New Configuration for RAM”). Writing a new configuration (register map) to the RAM consists of pausing the LOL state-machine, writing new values to the IC accounting for the write-allowed mask given in AN565, validating the input clock or crystal, locking the PLL to the input with the new configuration, restarting the LOL state-machine, and calibrating the VCO for robust operation across temperature. The flow chart in Figure 5 on page 13 enumerates the details: The first step in ordering a custom device is generating an NVM file which defines the input and output clock frequencies and signal formats. This is easily done using the NVMSave for Factory Programming... menu option in ClockBuilder Desktop. (See "3.1.1. ClockBuilder™ Desktop Software" on page 9.) This Windows based software allows the user to generate an NVM file, which is used by the factory to manufacture custom parts. Each custom part is marked with a unique part number identifying the specific configuration (e.g., Si5356A-A00100-GM). Note: The write-allowed mask specifies which bits must be read and modified before writing the entire register byte (a.k.a. read-modify-write). “AN428: Jump Start: InSystem, Flash-Based Programming for Silicon Labs’ Timing Products” illustrates the procedure defined in Section 3.5.2 with ANSI C code. Consult your local sales representative for more details on ordering a custom Si5356. 3.5.2. Creating a New Configuration for RAM Any Si5356 device can be configured by writing to registers in RAM through the I2C interface. A nonfactory programmed device must be configured in this manner. When creating a custom RAM configuration, use the following procedure: 1. Create a device configuration (register map) using ClockBuilder Desktop (v3.0 or later; see "3.1.1. ClockBuilder™ Desktop Software" on page 9) or manually using the equations in “AN565: Configuring the Si5356A”. a. Configure the frequency plan. b. Configure the output driver format and supply voltage. c. Configure initial phase offset (if desired). d. Configure spread spectrum (if desired). 2. Save the configuration using the Options > Save Register Map File or Options > Save C code Header File, or create the register contents by the conversions listed in AN565. At this point, the new configuration can be written to the device RAM according to the instructions in “3.5.3. Writing a Custom Configuration to RAM”. 12 Rev. 1.3 Si5356A Disable Outputs Set OEB_ALL = 1; reg230[4] Set reg241 = 0x65 Register Map Use ClockBuilder Desktop v3.0 or later Write new configuration to device accounting for the write-allowed mask (See AN565: Configuring the Si5356A) Apply Soft Reset Set SOFT_RESET = 1; reg246[1] If using down-spread: Set MS_RESET = 1; reg 226[2] = 1 Wait 1 ms Set MS_RESET = 0; reg 226[2] = 0 Enable Outputs Set OEB_ALL = 0; reg230[4] Figure 5. I2C Programming Procedure 3.5.4. Writing a Custom Configuration to NVM An alternative to ordering an Si5356 with a custom NVM configuration is to use the field programming kit (Si5338/56-PROG-EVB) to write directly to the NVM of a "blank" Si5356. Since NVM is an OTP memory, it can only be written once. The default configuration can be reconfigured by writing to RAM through the I2C interface (see “3.5.2. Creating a New Configuration for RAM”). 3.6. Output Phase Adjustment The Si5356 has a digitally-controlled phase adjustment feature that allows the user to adjust the phase of each output clock in relation to the other output clocks. The phase of each output clock can be adjusted with an error of <20 ps over a range of ±45 ns. This feature is available on any clock output that does not have Spread Spectrum enabled. 3.7. CMOS Output Drivers The Si5356 has 4 banks of outputs with each bank comprised of 2 clocks for a total of 8 CMOS outputs per device. By default, each bank of CMOS output clocks are in-phase. Alternatively, each output clock can be inverted. This feature enables each output pair to operate as a differential CMOS clock. Each of the output banks can operate from a different VDDO supply (1.8 V, 2.5 V, 3.3 V), simplifying usage in mixed supply applications. The CMOS output driver has a controlled impedance of close to 50 which includes an internal 22 series resistor. An external series resistor is not needed when driving 50 traces. If higher impedance traces are used then a series resistor may be added. A typical configuration is shown in Figure 6. 3.8. Jitter Performance The Si5356 provides consistently low jitter for any combination of output frequencies. The device leverages a low phase noise single PLL architecture and Silicon Laboratories’ patented MultiSynth fractional output divider technology to deliver excellent jitter performance guaranteed across process, temperature and voltage. The Si5356 provides superior performance to traditional multi-PLL solutions which may suffer from degraded jitter performance depending on frequency plan and the number of active PLLs. Rev. 1.3 13 Si5356A 3.9. Status Indicators An open-drain interrupt pin (INTR) is available to indicate a loss of signal (LOS) condition, a PLL loss of lock (LOL) condition, or that the PLL is in the process of acquiring lock (SYS_CAL). As shown in Figure 7, a status register at address 218 is available to help identify the exact event that caused the interrupt pin to become active. A LOS condition occurs when there is no clock input to the Si5356. The loss of lock algorithm works by continuously monitoring the frequency difference between the two inputs of the phase frequency detector. When this frequency difference is greater than about 1000 ppm, a loss of lock condition is declared. Note that the VCO will track the input clock frequency for up to approximately 25000 ppm, which will keep the inputs to the phase frequency detector at the same frequency until the PLL comes out of lock. When a clock input is removed, the interrupt pin will assert, and the clock outputs may drift up to 5%. When the input clock is reapplied with an appropriate frequency, the PLL will again lock. Si5356 +1.8V, +2.5V, +3.3V VDDOA Bank A MultiSynth CLK0 50 CLK1 50 PLL +1.8V, +2.5V, +3.3V VDDOB Bank B MultiSynth CLK2 50 CLK3 50 +1.8V, +2.5V, +3.3V VDDOC Bank C MultiSynth CLK4 50 CLK5 50 +1.8V, +2.5V, +3.3V VDDOD Bank D MultiSynth CLK6 CLK7 Figure 6. CMOS Output Driver Configuration 14 Rev. 1.3 50 50 Si5356A 3.10. I2C Interface The Si5356 control interface is a 2-wire bus for bidirectional communication. The bus consists of a bidirectional serial data line (SDA) and a serial clock input (SCL). The device operates as a slave device on the 2-wire bus and is compatible with I2C specifications. Both lines must be connected to the positive supply via an external pull-up. Standard-Mode (100 kbps) and Fast-Mode (400 kbps) operation and 7-bit addressing are supported as specified in the I2C-Bus Specification standard. To accommodate multiple Si5356 devices on the same I2C bus, the Si5356 has pin 3 as I2C_LSB. The complete 7-bit I2C bus address for the device is 70h or 71h depending upon the state of the I2C_LSB pin. In binary, this is written as 111 000[I2C_LSB]. See 218 7 6 5 Figure 8 for the command format for both read and write access. Data is always sent MSB first. Table 5 includes the AC and DC electrical parameters for the SCL and SDA I/ Os, respectively. The timing specifications and timing diagram for the I2C bus can be found in the I2C-Bus Specification standard. SDA timeout support is supported for compatibility with SMBus interfaces. The I2C interface is 3.3 V tolerant. The I2C bus can be operated at a bus voltage of 1.71 to 3.63 V and should have a pullup resistor as recommended by the I2C-Bus Specification. If the I2C bus voltage is less than 2.25 V, register 27[7] must be set to 1. LOL LOS Clk LOS XTAL 4 3 2 SYS Cal 1 0 System Calibration (Lock Acquisition) Loss of Signal XTAL Input Loss of Signal Clock Input Loss of Lock Figure 7. Status Register Rev. 1.3 15 Si5356A S Slv Addr [6:0] 0 A Reg Addr [7:0] A S Slv Addr [6:0] 1 A Data [7:0] A Data [7:0] N P Repeated Start Read S Slv Addr [6:0] 0 A Reg Addr [7:0] A P Write Data S S Slv Addr [6:0] Optional 1 A Two Command Read Slv Addr [6:0] 0 A Reg Addr [7:0] A Data [7:0] A Write From master to slave Data [7:0] A Data [7:0] N P Read Data Data [7:0] A Optional P Optional From slave to master 1 – Read 0 – Write A – Acknowledge (SDA LOW) N – Not Acknowledge (SDA HIGH). Required after the last data byte to signal the end of the read comand to the slave. S – START condition P – STOP condition Figure 8. I2C/SMBus-Compatible Command Format 3.11. Spread Spectrum To help reduce electromagnetic interference (EMI), the Si5356A supports spread spectrum modulation. The output clock frequencies can be modulated to spread energy across a broader range of frequencies, lowering system EMI. The Si5356A implements spread spectrum using its patented MultiSynth technology to achieve previously unattainable precision in both modulation rate and spreading magnitude as shown in Figure 9. Through I2C control, the Spread Spectrum can be applied to any output clock, any clock frequency, and any spread amount from ±0.1% to ±2.5% center spread and –0.1% to –5% down spread . down-spread register parameters. Consult AN565 for details. Note: If you currently use center spread on a revision A and would like to migrate to a revision B device, you must generate a new register map using either ClockBuilder Desktop or the equations in AN565. Center spread configurations for Revisions A and B are not compatible. The spreading rate is limited to 30 to 63 kHz. The Spread Spectrum is generated digitally in the output MultiSynths which means that the Spread Spectrum parameters are virtually independent of process, voltage, and temperature variations. Since the Spread Spectrum is created in the output MultiSynths, through I2C each output channel can have independent Spread Spectrum parameters. Without the use of I2C (NVM download only) the only supported Spread Spectrum parameters are for PCI Express compliance composing 100 MHz clock, 31.5 kHz spreading frequency with the choice of the spreading. Rev A devices provide native support for both down and center spread. Center spread is supported in rev B devices by up-shifting the nominal frequency and using 16 Rev. 1.3 Si5356A 0 No spread -10 -20 Relative Power (dB) -30 -40 ±1.0% -50 ±2.5% -60 ±5.0% -70 -80 -90 -10% -8% -6% -4% -2% 0% 2% 4% 6% 8% 10% Relative Frequency Figure 9. Configurable Spread Spectrum Rev. 1.3 17 Si5356A 3.12. Power Supply Considerations The Si5356 has two core supply voltage pins (VDD) and four clock output bank supply voltage pins (VDDOA– VDDOD), enabling the device to be used in mixed supply applications. The Si5356 does not require ferrite beads for power supply filtering. The device has extensive on- chip power supply regulation to minimize the impact of power supply noise on output jitter. Figure 10 is a curve of additive phase jitter with power supply noise. Note that even when a significant amount of noise is applied to the device power supply, additive phase jitter is still very small. Figure 10. Peak-to-Peak Additive Phase Jitter from 100 mV Sine Wave on Supply 18 Rev. 1.3 Si5356A 4. Si5356 Registers For many applications, the Si5356's register values are easily configured using ClockBuilder Desktop (see "3.1.1. ClockBuilder™ Desktop Software" on page 9). However, for customers interested in using the Si5356 in operating modes beyond the capabilities available with ClockBuilder, refer to “AN565: Configuring the Si5356A” for a detailed description of the Si5356 registers and their usage. Also refer to “AN428: Jump Start: In-System, Flash-Based Programming for Silicon Labs’ Timing Products” for a working application example of register programming using the Silicon Labs' C8051F301 MCU. Rev. 1.3 19 Si5356A 5. Pin Descriptions VDD GND CLK0 CLK1 VDDOA SDA Top View 24 23 22 21 20 19 XA 1 18 CLK2 XB 2 17 CLK3 16 VDDOB I2C_LSB 3 GND GND CLKIN 4 15 VDDOC 14 CLK4 SSC_DIS 5 9 10 INTR CLK7 CLK6 11 12 SCL 8 VDDOD 7 VDD OEB 6 13 CLK5 Note: Center pad must be tied to GND for normal operation. Table 8. Si5356 Pin Descriptions Pin # Pin Name 20 I/O Description 1 XA I External Crystal. If a 25 or 27 MHz crystal is used as the device frequency reference, connect it across XA and XB. If no input clock is used, this pin should be tied to GND. 2 XB I External Crystal. If a 25 or 27 MHz crystal is used as the device frequency reference, connect it across XA and XB. If no input clock is used, this pin should be tied to GND. 3 I2C_LSB I I2C LSB Address Bit (3.3 V Tolerant). This pin is the least significant bit of the Si5356 I2C address allowing up to two Si5356 devices to occupy the same I2C bus. 4 CLKIN I Single-Ended Input Clock. If a single-ended clock is used as the device frequency reference, connect it to this pin. This pin functions as a high-impedance input for CMOS clock signals. The input should be dc coupled. If a crystal is used as the device frequency reference, this pin should be tied to GND. Rev. 1.3 Si5356A Table 8. Si5356 Pin Descriptions (Continued) 5 SSC_DIS I Spread Spectrum Disable. This pin allows disabling of the spread spectrum feature on the output clocks. Note that the maximum voltage level on this pin must not exceed 1.3 V. To disable spread spectrum connect this pin to a voltage of 0.85 to 1.3 V. Connect to GND to enable spread spectrum. A resistor voltage divider is recommended when controlled by a signal greater than 1.3 V. See the Typical Application Circuit for details. 6 OEB I Output Enable (Active Low). This pin allows disabling the output clocks. Note that the maximum voltage level on this pin must not exceed 1.3 V. To disable all outputs connect this pin to a voltage of 0.85 to 1.3 V. Connect to GND to enable all outputs. A resistor voltage divider is recommended when controlled by a signal greater than 1.3 V. See the Typical Application Circuit for details. 7 VDD 8 INTR O Interrupt. A typical pullup resistor of 1–4 k should be used on this pin. This pin functions as an maskable interrupt output. 0 = No interrupt 1 = Interrupt present This pin is open drain and requires an external >1 k pullup resistor. 9 CLK7 O Output Clock 7. CMOS output clock. If unused, this pin must be left floating. 10 CLK6 O Output Clock 6. CMOS output clock. If unused, this pin must be left floating. 11 VDDOD 12 SCL I I2C Serial Clock Input (3.3 V Tolerant). 13 CLK5 O Output Clock 5. CMOS output clock. If unused, this pin must be left floating. 14 CLK4 O Output Clock 4. CMOS output clock. If unused, this pin must be left floating. 15 VDDOC VDD Clock Output Bank C Supply Voltage. Power supply for clock outputs 4 and 5. May be operated from a 1.8, 2.5 or 3.3 V supply. A 0.1 μF bypass capacitor should be located very close to this pin. If CLK4/5 are not used, this pin must be tied to pin 7 and/or pin 24 or a voltage rail > 1.5 V. 16 VDDOB VDD Clock Output Bank B Supply Voltage. Power supply for clock outputs 2 and 3. May be operated from a 1.8, 2.5, or 3.3 V supply. A 0.1 μF bypass capacitor should be located very close to this pin. If CLK2/3 are not used, this pin must be tied to pin 7 and/or pin 24 or a voltage rail > 1.5 V. 17 CLK3 VDD Core Supply Voltage. The device operates from a 1.8, 2.5, or 3.3 V supply. A 0.1 μF bypass capacitor should be located very close to this pin. VDD Clock Output Bank D Supply Voltage. Power supply for clock outputs 6 and 7. May be operated from a 1.8, 2.5, or 3.3 V supply. A 0.1 μF bypass capacitor should be located very close to this pin. If CLK6/7 are not used, this pin must be tied to pin 7 and/or pin 24 or a voltage rail > 1.5 V. O Output Clock 3. CMOS output clock. If unused, this pin must be left floating. Rev. 1.3 21 Si5356A Table 8. Si5356 Pin Descriptions (Continued) 18 CLK2 O Output Clock 2. CMOS output clock. If unused, this pin must be left floating. 19 SDA I/O I2C Serial Data (3.3 V Tolerant). 20 VDDOA 21 CLK1 O Output Clock 1. CMOS output clock. If unused, this pin must be left floating. 22 CLK0 O Output Clock 0. CMOS output clock. If unused, this pin must be left floating. 23 GND GND Ground. Must be connected to system ground. Minimize the ground path impedance for optimal performance of the device. 24 VDD VDD Core Supply Voltage. The device operates from a 1.8, 2.5, or 3.3 V supply. A 0.1 μF bypass capacitor should be located very close to this pin. GND PAD GND GND Ground Pad. This is the large pad in the center of the package. The device will not function unless the ground pad is properly connected to a ground plane on the PCB. See "8. Recommended PCB Land Pattern" on page 25 for the PCB pad sizes and ground via requirements. 22 VDD Clock Output Bank A Supply Voltage. Power supply for clock outputs 0 and 1. May be operated from a 1.8, 2.5, or 3.3 V supply. A 0.1 μF bypass capacitor should be located very close to this pin. If CLK0/1 are not used, this pin must be tied to pin 7 and/or pin 24 or a voltage rail > 1.5 V. Rev. 1.3 Si5356A 6. Ordering Guide Si5356A Bxxxxx GMR GMR = tape & reel GM = trays Contact your Silicon Labs sales representative for details regarding shipment media. I2C Programmable Any-Frequency 1–200 MHz Quad Frequency 8-Output Clock Generator B = product revision B xxxxx = 5-digit custom code assigned to each unique device configuration. Leave xxxxx blank for standard factory default configuration (Si5356A-B-GMR) 6.1. Evaluation Board Si5356 EVB Rev. 1.3 Si5356 Evaluation Board 23 Si5356A 7. Package Outline: 24-Lead QFN Figure 11. 24-Lead Quad Flat No-Lead (QFN) Table 9. Package Dimensions Dimension Min Nom Max A 0.80 0.85 0.90 A1 0.00 0.02 0.05 b 0.18 0.25 0.30 D D2 4.00 BSC. 2.35 2.50 e 0.50 BSC. E 4.00 BSC. 2.65 E2 2.35 2.50 2.65 L 0.30 0.40 0.50 aaa 0.10 bbb 0.10 ccc 0.08 ddd 0.10 eee 0.05 Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This drawing conforms to the JEDEC Outline MO-220, variation VGGD-8. 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. 5. J-STD-020 MSL rating: MSL3. 6. Terminal base alloy: Cu. 7. Terminal plating/grid array material: Au/NiPd. 8. For more packaging information, go to www.silabs.com/support/quality/pages/RoHSInformation.aspx. 24 Rev. 1.3 Si5356A 8. Recommended PCB Land Pattern Table 10. PCB Land Pattern Dimension P1 P2 X1 Y1 C1 C2 E Min 2.50 2.50 0.20 0.75 Nom 2.55 2.55 0.25 0.80 3.90 3.90 0.50 Max 2.60 2.60 0.30 0.85 Notes: General 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994 specification. 3. This Land Pattern Design is based on the IPC-7351 guidelines. 4. Connect the center ground pad to a ground plane with no less than five vias. These 5 vias should have a length of no more than 20 mils to the ground plane. Via drill size should be no smaller than 10 mils. A longer distance to the ground plane is allowed if more vias are used to keep the inductance from increasing. Solder Mask Design 5. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 µm minimum, all the way around the pad. Stencil Design 6. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 7. The stencil thickness should be 0.125 mm (5 mils). 8. The ratio of stencil aperture to land pad size should be 1:1 for all perimeter pins. 9. A 2x2 array of 1.0 mm square openings on 1.25 mm pitch should be used for the center ground pad. Card Assembly 10. A No-Clean, Type-3 solder paste is recommended. 11. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. Rev. 1.3 25 Si5356A 9. Top Marking 9.1. Si5356A Top Marking Si5356 Axxxxx RTTTTT YYWW 9.2. Top Marking Explanation Mark Method: Laser Line 1 Marking: Device Part Number Line 2 Marking: Axxxxx A = Frequency and configuration code. I2C programmable, any-frequency 1–200 MHz, quad frequency, 8-output clock generator. xxxxx = NVM code for custom factoryprogrammed devices (characters are not included for blank devices). See Ordering Guide section in data sheet for more information. Line 3 Marking: R = Product revision. TTTTT = Manufacturing trace code. RTTTTT Line 4 Marking: Pin 1 indicator. Circle with 0.5 mm diameter; left-justified YY = Year. WW = Work week. Characters correspond to the year and work week of package assembly. YYWW 26 Rev. 1.3 Si5356 Si5356A 10. Device Errata Please visit www.silabs.com to access the device errata document. Rev. 1.3 27 Si5356A DOCUMENT CHANGE LIST Revision 1.0 to Revision 1.1 Updated Figure 5 on page 13 to provide workaround for spread spectrum errata. Added " Document Change List" on page 28. Revision 0.1 to Revision 0.2 Improved specification details on input signals. Added phase and cycle-cycle jitter specifications. Added thermal resistance junction to case. Improved application circuits. Added GND via requirement details. Added differential CMOS capability. Revision 1.1 to Revision 1.2 Revision 0.2 to Revision 0.3 Removed down spread spectrum errata that has been corrected in Revision B. Updated ordering information to refer to Revision B silicon. Updated top marking explanation in table. Added further explanation to describe revisionspecific behavior of center spread spectrum in Section 3.11 Added Section “3.1. Overview” Updated Section “3.2. Input Configuration” Updated Section “3.4. Frequency Configuration” Added Section “3.5. Configuring the Si5356” Added Section “4. Si5356 Registers” Added Section “9. Top Marking” Updated “Figure 10. Peak-to-Peak Additive Phase Jitter from 100 mV Sine Wave on Supply” Revision 1.2 to Revision 1.3 Revision 0.3 to Revision 1.0 Renamed part number on page header from Si5356 to Si5356A. Updated Table 2. DC Characteristics. Added IDDOx specification. Pn Input Resistance specification. Corrected Updated Table 3, “AC Characteristics,” on page 5. Added 10–90% input clock rise/fall time. LOS assert/deassert time. Added note on jitter test. Updated 20–80% rise/fall time with CL = 15 pF for output clocks to the maximum value of 2.0 ns. Changed Frequency Synthesis Resolution spec to the correct value of 1ppb max. Added Updated recommended crystal load parameters in Table 4 on page 6. Updated Table 6 on page 7. Added Soldering profile specification Input Voltage Range (VI2) to 1.3 V (max). Corrected Added packaging/RoHS information. Removed section “3.5.4. Modifying a MultiSynth Output Divider Ratio/Frequency Configuration.” Removed output-to-output skew spec from text in section "3.7. CMOS Output Drivers" to prevent duplicating spec in “Table 3. AC Characteristics.” Removed jitter spec from text in section "3.8. Jitter Performance" to prevent duplicating spec in “Table 3. AC Characteristics.” Added Evaluation Board information to the Ordering Guide. 28 Rev. 1.3 Added link to errata document. Si5356A CONTACT INFORMATION Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 Tel: 1+(512) 416-8500 Fax: 1+(512) 416-9669 Toll Free: 1+(877) 444-3032 Please visit the Silicon Labs Technical Support web page: https://www.silabs.com/support/pages/contacttechnicalsupport.aspx and register to submit a technical support request. Patent Notice Silicon Labs invests in research and development to help our customers differentiate in the market with innovative low-power, small size, analogintensive mixed-signal solutions. Silicon Labs' extensive patent portfolio is a testament to our unique approach and world-class engineering team The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories, Silicon Labs, and ClockBuilder are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders. Rev. 1.3 29