Si5338 Data Sheet

S i53 3 8
I 2 C-P R O G R A M M A B L E A N Y -F R E Q U E N C Y, A N Y -O U T P U T
QUAD CLOCK GENERATOR
Features







Low power MultiSynth™ technology 
enables independent, any-frequency
synthesis on four differential output

drivers
Highly-configurable output drivers with
up to four differential outputs, eight
single-ended clock outputs, or a

combination of both
Low phase jitter of 0.7 ps RMS typ
High precision synthesis allows true 
zero ppm frequency accuracy on all
outputs
Flexible input reference:
External crystal: 8 to 30 MHz
CMOS input: 5 to 200 MHz
SSTL/HSTL input: 5 to 350 MHz

Differential input: 5 to 710 MHz

Independently configurable outputs
support any frequency or format:
LVPECL/LVDS: 0.16 to 710 MHz

HCSL: 0.16 to 250 MHz

CMOS: 0.16 to 200 MHz

SSTL/HSTL: 0.16 to 350 MHz

Independent output voltage per driver: 
1.5, 1.8, 2.5, or 3.3 V
Single supply core with excellent
PSRR: 1.8, 2.5, 3.3 V
Independent frequency increment/
decrement feature enables
glitchless frequency adjustments in
1 ppm steps
Independent phase adjustment on
each of the output drivers with an
accuracy of <20 ps steps
Highly configurable spread
spectrum (SSC) on any output:
Any frequency from 5 to 350 MHz
Any spread from 0.5 to 5.0%
Any modulation rate from 33 to
63 kHz
External feedback mode allows
zero-delay mode
Loss of lock and loss of signal
alarms
Ordering Information:
See page 42.
Pin Assignments
I2C/SMBus compatible interface
Easy to use programming software
Small size: 4 x 4 mm, 24-QFN
Low power: 45 mA core supply typ
Wide temperature range: –40 to
+85 °C
Applications




Ethernet switch/router
PCI Express 2.0/3.0
Broadcast video/audio timing
Processor and FPGA clocking
 Any-frequency clock conversion
 MSAN/DSLAM/PON
 Fibre Channel, SAN
 Telecom line cards
 1 GbE and 10 GbE
Description
The Si5338 is a high-performance, low-jitter clock generator capable of
synthesizing any frequency on each of the device's four output drivers. This timing
IC is capable of replacing up to four different frequency crystal oscillators or
operating as a frequency translator. Using its patented MultiSynth™ technology,
the Si5338 allows generation of four independent clocks with 0 ppm precision.
Each output clock is independently configurable to support various signal formats
and supply voltages. The Si5338 provides low-jitter frequency synthesis in a
space-saving 4 x 4 mm QFN package. The device is programmable via an I2C/
SMBus-compatible serial interface and supports operation from a 1.8, 2.5, or
3.3 V core supply. I2C device programming is made easy with the ClockBuilder™
Desktop software available at www.silabs.com/ClockBuilder.
Rev. 1.5 6/15
Copyright © 2015 by Silicon Laboratories
Si5338
Si5 338
Functional Block Diagram
2
Rev. 1.5
Si5338
TA B L E O F C O N T E N T S
Section
Page
1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2. Typical Application Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
3. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
3.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
3.2. Input Stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
3.3. Synthesis Stages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
3.4. Output Stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.5. Configuring the Si5338 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.6. Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
3.7. Output Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
3.8. Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
3.9. Reset Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
3.10. Features of the Si5338 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
4. Applications of the Si5338 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
4.1. Free-Running Clock Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
4.2. Synchronous Frequency Translation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
4.3. Configurable Buffer and Level Translator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
2C Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
5. I
6. Si5338 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
7. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
8. Device Pinout by Part Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
9. Package Outline: 24-Lead QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
10. Recommended PCB Land Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
11. Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
11.1. Si5338 Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
11.2. Top Marking Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
12. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
13. Device Errata . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Rev. 1.5
3
Si5 338
1. Electrical Specifications
Table 1. Recommended Operating Conditions
(VDD = 1.8 V –5% to +10%, 2.5 V ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Ambient Temperature
Test Condition
TA
VDD
Core Supply Voltage
Output Buffer Supply
Voltage
VDDOn
Min
Typ
Max
Unit
–40
25
85
°C
2.97
3.3
3.63
V
2.25
2.5
2.75
V
1.71
1.8
1.98
V
1.4
—
3.63
V
Note: All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions.
Typical values apply at nominal supply voltages and an operating temperature of 25 °C unless otherwise noted.
Table 2. Absolute Maximum Ratings1
Parameter
Symbol
Test Condition
Value
Unit
DC Supply Voltage
VDD
–0.5 to 3.8
V
Storage Temperature Range
TSTG
–55 to 150
°C
ESD Tolerance
HBM
(100 pF, 1.5 k)
2.5
kV
ESD Tolerance
CDM
550
V
ESD Tolerance
MM
175
V
Latch-up Tolerance
JESD78 Compliant
Junction Temperature
Peak Soldering Reflow
TJ
Temperature2
150
°C
260
°C
Notes:
1. Permanent device damage may occur if the absolute maximum ratings are exceeded. Functional operation should be
restricted to the conditions as specified in the operational sections of this data sheet. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
2. Refer to JEDEC J-STD-020 standard for more information.
4
Rev. 1.5
Si5338
Table 3. DC Characteristics
(VDD = 1.8 V –5% to +10%, 2.5 V ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Core Supply Current
IDD
100 MHz on all outputs,
25 MHz refclk
—
45
60
mA
Core Supply Current
(Buffer Mode)
IDDB
50 MHz refclk
—
12
—
mA
LVPECL, 710 MHz
—
—
30
mA
LVDS, 710 MHz
—
—
8
mA
HCSL, 250 MHz
2 pF load
—
—
20
mA
CML, 350 MHz
—
12
—
mA
SSTL, 350 MHz
—
—
19
mA
CMOS, 50 MHz
15 pF load1
—
6
9
mA
CMOS, 200 MHz1,2
3.3 V VDD0
—
13
18
mA
CMOS, 200 MHz1,2
2.5 V
—
10
14
mA
CMOS, 200 MHz1,2
1.8 V
—
7
10
mA
HSTL, 350 MHz
—
—
19
mA
IDDOx
Output Buffer Supply Current
Notes:
1. Single CMOS driver active.
2. Measured into a 5” 50  trace with 2 pF load.
Table 4. Thermal Characteristics
Parameter
Symbol
Test Condition
Value
Unit
Thermal Resistance
Junction to Ambient
JA
Still Air
37
°C/W
Thermal Resistance
Junction to Case
JC
Still Air
10
°C/W
Rev. 1.5
5
Si5 338
Table 5. Performance Characteristics
(VDD = 1.8 V –5% to +10%, 2.5 V ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
PLL Acquisition Time
tACQ
—
—
25
ms
PLL Tracking Range
fTRACK
5000
20000
—
ppm
PLL Loop Bandwidth
fBW
—
1.6
—
MHz
MultiSynth Frequency
Synthesis Resolution
fRES
0
0
1
ppb
CLKIN Loss of Signal Detect
Time
tLOS
—
2.6
5
μs
CLKIN Loss of Signal Release
Time
tLOSRLS
0.01
0.2
1
μs
PLL Loss of Lock Detect Time
tLOL
—
5
10
ms
POR to Output Clock Valid
(Pre-programmed Devices)
tRDY
—
—
2
ms
Input-to-Output Propagation
Delay
tPROP
Buffer Mode
(PLL Bypass)
—
2.5
4
ns
tDSKEW
Rn divider = 11
—
—
100
ps
—
—
15
ms
–45
—
+45
ns
Output-Output Skew
Output frequency < Fvco/8
POR to I2C Ready
Programmable Initial
Phase Offset
POFFSET
Phase Increment/Decrement
Accuracy
PSTEP
—
—
20
ps
Phase Increment/Decrement
Range
PRANGE
–45
—
+45
ns
MultiSynth range for phase
increment/decrement
fPRANGE
5
—
Fvco/82
MHz
Phase Increment/Decrement
Update Time
PUPDATE
667
—
—
ns
Pin control2,3
MultiSynth output >18 MHz
Notes:
1. Outputs at integer-related frequencies and using the same driver format. See "3.10.3. Programmable Initial Phase
Offset" on page 27.
2. The maximum step size is only limited by the register lengths; however, the MultiSynth output frequency must be kept
between 5 MHz and Fvco/8.
3. Update rate via I2C is also limited by the time it takes to perform a write operation.
4. Default value is 0.5% down spread.
5. Default value is ~31.5 kHz.
6
Rev. 1.5
Si5338
Table 5. Performance Characteristics (Continued)
(VDD = 1.8 V –5% to +10%, 2.5 V ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
PUPDATE
Pin control2,3
MultiSynth output <18 MHz
Number of periods of
MultiSynth output frequency
—
10
12
Periods
fSTEP
R divider not used
1
—
See
Note 2
ppm
MultiSynth range for frequency
increment/decrement
fRANGE
R divider not used
5
—
Fvco/8
MHz
Frequency Increment/
Decrement Update Time
fUPDATE
Pin control2,3
MultiSynth output >18 MHz
—
—
667
ns
Frequency Increment/
Decrement Update Time
fUPDATE
Pin control2,3
MultiSynth output <18 MHz
Number of periods of
MultiSynth output frequency
—
10
12
Periods
Spread Spectrum PP
Frequency Deviation
SSDEV
MultiSynth Output < ~Fvco/8
0.1
—
5.04
%
Spread Spectrum Modulation
Rate
SSDEV
MultiSynth Output < ~Fvco/8
30
—
635
kHz
Phase Increment/Decrement
Update Time
Frequency Increment/
Decrement Step Size
Notes:
1. Outputs at integer-related frequencies and using the same driver format. See "3.10.3. Programmable Initial Phase
Offset" on page 27.
2. The maximum step size is only limited by the register lengths; however, the MultiSynth output frequency must be kept
between 5 MHz and Fvco/8.
3. Update rate via I2C is also limited by the time it takes to perform a write operation.
4. Default value is 0.5% down spread.
5. Default value is ~31.5 kHz.
Rev. 1.5
7
Si5 338
Table 6. Input and Output Clock Characteristics
(VDD = 1.8 V –5% to +10%, 2.5 V ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
5
—
710
MHz
Input Clock (AC Coupled Differential Input Clocks on Pins IN1/2, IN5/6)1
Frequency
fIN
Differential Voltage
Swing
VPP
710 MHz input
0.4
—
2.4
VPP
Rise/Fall Time2
tR/tF
20%–80%
—
—
1.0
ns
Duty Cycle
DC
< 1 ns tr/tf
40
—
60
%
Duty Cycle
DC
(PLL bypass)3
< 1 ns tr/tf
45
—
55
%
Input Impedance1
RIN
10
—
—
k
Input Capacitance
CIN
—
3.5
—
pF
5
—
200
MHz
–0.1
—
3.73
V
200 MHz
0.8
—
VDD+10%
Vpp
Input Clock (DC-Coupled Single-Ended Input Clock on Pins IN3/4)
Frequency
fIN
Input Voltage
VI
Input Voltage Swing
CMOS
Rise/Fall Time4
tR/tF
10%–90%
—
—
4
ns
Time4
tR/tF
20%–80%
—
—
2.3
ns
Duty Cycle5
DC
< 4 ns tr/tf
40
—
60
%
Input Capacitance
CIN
—
2.0
—
pF
0.16
—
350
MHz
367
—
473.33
MHz
550
—
710
MHz
0.16
—
250
MHz
Rise/Fall
Output Clocks (Differential)
Frequency6
fOUT
LVPECL, LVDS,
CML
HCSL
Notes:
1. Use an external 100  resistor to provide load termination for a differential clock. See Figure 3.
2. For best jitter performance, keep the midpoint differential input slew rate on pins 1,2,5,6 faster than 0.3 V/ns.
3. Minimum input frequency in clock buffer mode (PLL bypass) is 5 MHz. Operation to 1 MHz is also supported in buffer
mode, but loss-of-signal (LOS) status is not functional.
4. For best jitter performance, keep the mid point input single ended slew rate on pins 3 or 4 faster than 1 V/ns.
5. Not in PLL bypass mode.
6. Only two unique frequencies above 350 MHz can be simultaneously output, Fvco/4 and Fvco/6. See "3.3. Synthesis
Stages" on page 19.
7. CML output format requires ac-coupling of the differential outputs to a differential 100  load at the receiver.
8. Includes effect of internal series 22  resistor.
8
Rev. 1.5
Si5338
Table 6. Input and Output Clock Characteristics (Continued)
(VDD = 1.8 V –5% to +10%, 2.5 V ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
VOC
common mode
—
VDDO–
1.45 V
—
V
VSEPP
peak-to-peak single-ended swing
0.55
0.8
0.96
VPP
VOC
common mode
1.125
1.2
1.275
V
VSEPP
Peak-to-Peak
Single-Ended
Swing
0.25
0.35
0.45
VPP
VOC
Common Mode
0.8
0.875
0.95
V
VSEPP
Peak-to-Peak
Single-Ended
Swing
0.25
0.35
0.45
VPP
VOC
Common Mode
0.35
0.375
0.400
V
VSEPP
Peak-to-Peak
Single-Ended
Swing
0.575
0.725
0.85
VPP
VOC
Common Mode
—
See Note 7
—
V
VSEPP
Peak-to-Peak
Single-Ended
Swing
0.67
0.860
1.07
VPP
Rise/Fall Time
tR/tF
20%–80%
—
—
450
ps
Duty Cycle5
DC
45
—
55
%
CMOS
0.16
—
200
MHz
SSTL, HSTL
0.16
—
350
MHz
LVPECL Output
Voltage
LVDS Output Voltage
(2.5/3.3 V)
LVDS Output
Voltage (1.8 V)
HCSL Output Voltage
CML Output Voltage
Output Clocks (Single-Ended)
Frequency
fOUT
CMOS 20%–80%
Rise/Fall Time
tR/tF
2 pF load
—
0.45
0.85
ns
CMOS 20%–80%
Rise/Fall Time
tR/tF
15 pF load
—
—
2.0
ns
Notes:
1. Use an external 100  resistor to provide load termination for a differential clock. See Figure 3.
2. For best jitter performance, keep the midpoint differential input slew rate on pins 1,2,5,6 faster than 0.3 V/ns.
3. Minimum input frequency in clock buffer mode (PLL bypass) is 5 MHz. Operation to 1 MHz is also supported in buffer
mode, but loss-of-signal (LOS) status is not functional.
4. For best jitter performance, keep the mid point input single ended slew rate on pins 3 or 4 faster than 1 V/ns.
5. Not in PLL bypass mode.
6. Only two unique frequencies above 350 MHz can be simultaneously output, Fvco/4 and Fvco/6. See "3.3. Synthesis
Stages" on page 19.
7. CML output format requires ac-coupling of the differential outputs to a differential 100  load at the receiver.
8. Includes effect of internal series 22  resistor.
Rev. 1.5
9
Si5 338
Table 6. Input and Output Clock Characteristics (Continued)
(VDD = 1.8 V –5% to +10%, 2.5 V ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
CMOS Output
Resistance
—
50
—

SSTL Output
Resistance
—
50
—

HSTL Output
Resistance
—
50
—

VDDO – 0.3
—
CMOS Output Voltage8
VOH
4 mA load
VOL
4 mA load
SSTL Output Voltage
VOH
VOL
VOH
VOL
VOH
VOL
HSTL Output Voltage
VOH
VOL
Duty Cycle5
V
—
0.3
V
SSTL-3
0.45xVDDO+0.41
VDDOx = 2.97 to
—
3.63 V
—
—
V
—
0.45xVDDO
–0.41
V
SSTL-2
VDDOx = 2.25 to
2.75 V
0.5xVDDO+0.41
—
—
V
—
—
0.5xVDDO–
0.41
V
SSTL-18
VDDOx = 1.71 to
1.98 V
0.5xVDDO+0.34
—
—
—
0.5xVDDO–
0.34
V
VDDO = 1.4 to
1.6 V
0.5xVDDO+0.3
—
—
V
—
—
0.5xVDDO –
0.3
V
45
—
55
%
DC
V
Notes:
1. Use an external 100  resistor to provide load termination for a differential clock. See Figure 3.
2. For best jitter performance, keep the midpoint differential input slew rate on pins 1,2,5,6 faster than 0.3 V/ns.
3. Minimum input frequency in clock buffer mode (PLL bypass) is 5 MHz. Operation to 1 MHz is also supported in buffer
mode, but loss-of-signal (LOS) status is not functional.
4. For best jitter performance, keep the mid point input single ended slew rate on pins 3 or 4 faster than 1 V/ns.
5. Not in PLL bypass mode.
6. Only two unique frequencies above 350 MHz can be simultaneously output, Fvco/4 and Fvco/6. See "3.3. Synthesis
Stages" on page 19.
7. CML output format requires ac-coupling of the differential outputs to a differential 100  load at the receiver.
8. Includes effect of internal series 22  resistor.
10
Rev. 1.5
Si5338
Table 7. Control Pins
(VDD = 1.8 V –5% to +10%, 2.5 V ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Condition
Min
Typ
Max
Unit
Input Control Pins (IN3, IN4)
Input Voltage Low
VIL
–0.1
—
0.3 x VDD
V
Input Voltage High
VIH
0.7 x VDD
—
3.73
V
Input Capacitance
CIN
—
—
4
pF
Input Resistance
RIN
—
20
—
k
Output Control Pins (INTR)
Output Voltage Low
VOL
ISINK = 3 mA
0
—
0.4
V
Rise/Fall Time 20–80%
tR/tF
CL < 10 pf, pull up 1 k
—
—
10
ns
Symbol
Min
Typ
Max
Unit
fXTAL
8
—
11
MHz
cL (supported)*
11
12
13
pF
cL (recommended)
17
18
19
pF
cO
—
—
6
pF
rESR
—
—
300

dL
100
—
—
μW
Table 8. Crystal Specifications for 8 to 11 MHz
Parameter
Crystal Frequency
Load Capacitance (on-chip differential)
Crystal Output Capacitance
Equivalent Series Resistance
Crystal Max Drive Level
*Note: See "AN360: Crystal Selection Guide for Si533x and Si5355/56 Devices" for how to adjust the registers to
accommodate a 12 pF crystal CL.
Table 9. Crystal Specifications for 11 to 19 MHz
Parameter
Crystal Frequency
Symbol
Min
Typ
Max
Unit
fXTAL
11
—
19
MHz
cL (supported)*
11
12
13
pF
cL (recommended)
17
18
19
pF
cO
—
—
5
pF
rESR
—
—
200

dL
100
—
—
μW
Load Capacitance (on-chip differential)
Crystal Output Capacitance
Equivalent Series Resistance
Crystal Max Drive Level
*Note: See "AN360: Crystal Selection Guide for Si533x and Si5355/56 Devices" for how to adjust the registers to
accommodate a 12 pF crystal CL.
Rev. 1.5
11
Si5 338
Table 10. Crystal Specifications for 19 to 26 MHz
Parameter
Symbol
Min
fXTAL
19
cL (supported)*
11
cL (recommended)
17
Crystal Frequency
Typ
Max
Unit
26
MHz
12
13
pF
18
19
pF
cO
5
pF
rESR
100

Load Capacitance (on-chip differential)
Crystal Output Capacitance
Equivalent Series Resistance
Crystal Max Drive Level
dL
100
μW
*Note: See "AN360: Crystal Selection Guide for Si533x and Si5355/56 Devices" for how to adjust the registers to
accommodate a 12 pF crystal CL.
Table 11. Crystal Specifications for 26 to 30 MHz
Parameter
Crystal Frequency
Symbol
Min
fXTAL
26
cL (supported)*
11
cL (recommended)
17
Typ
Max
Unit
30
MHz
12
13
pF
18
19
pF
cO
5
pF
rESR
75

Load Capacitance (on-chip differential)
Crystal Output Capacitance
Equivalent Series Resistance
Crystal Max Drive Level
dL
100
*Note: See "AN360: Crystal Selection Guide for Si533x and Si5355/56 Devices" for how to adjust the registers to
accommodate a 12 pF crystal CL.
12
Rev. 1.5
μW
Si5338
Table 12. Jitter Specifications1,2,3
(VDD = 1.8 V –5% to +10%, 2.5 V ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
GbE Random Jitter
(12 kHz–20 MHz)4
JGbE
CLKIN = 25 MHz
All CLKn at 125 MHz5
—
0.7
1
ps RMS
GbE Random Jitter
(1.875–20 MHz)
RJGbE
CLKIN = 25 MHz
All CLKn at 125 MHz5
—
0.38
0.79
ps RMS
OC-12 Random Jitter
(12 kHz–5 MHz)
JOC12
CLKIN = 19.44 MHz
All CLKn at
155.52 MHz5
—
0.7
1
ps RMS
Total Jitter6
—
20.1
33.6
ps pk-pk
RMS Jitter6, 10 kHz to
1.5 MHz
—
0.15
1.47
ps RMS
RMS Jitter6, 1.5 MHz to
50 MHz
—
0.58
0.75
ps RMS
RMS Jitter6
—
0.15
0.45
ps RMS
PCI Express 1.1 Common
Clocked
PCI Express 2.1 Common
Clocked
PCI Express 3.0 Common
Clocked
JPER
N = 10,000 cycles7
—
10
30
ps pk-pk
Cycle-Cycle Jitter
JCC
N = 10,000 cycles
Output MultiSynth
operated in integer or
fractional mode7
—
9
29
ps pk8
Random Jitter
(12 kHz–20 MHz)
RJ
Output and feedback
MultiSynth in integer or
fractional mode7
—
0.7
1.5
ps RMS
Period Jitter
Notes:
1. All jitter measurements apply for LVDS/HCSL/LVPECL/CML output format with a low noise differential input clock and
are made with an Agilent 90804 oscilloscope. All RJ measurements use RJ/DJ separation.
2. For best jitter performance, keep the single ended clock input slew rates at Pins 3 and 4 more than 1.0 V/ns and the
differential clock input slew rates more than 0.3 V/ns.
3. All jitter data in this table is based upon all output formats being differential. When single-ended outputs are used, there
is the potential that the output jitter may increase due to the nature of single-ended outputs. If your configuration
implements any single-ended output and any output is required to have jitter less than 3 ps rms, contact Silicon Labs
for support to validate your configuration and ensure the best jitter performance. In many configurations, CMOS
outputs have little to no effect upon jitter.
4. DJ for PCI and GbE is < 5 ps pp
5. Output MultiSynth in Integer mode.
6. All output clocks 100 MHz HCSL format. Jitter is from the PCIE jitter filter combination that produces the highest jitter.
See AN562 for details. Jitter is measured with the Intel Clock Jitter Tool, Ver. 1.6.4.
7. Input frequency to the Phase Detector between 25 and 40 MHz and any output frequency > 5 MHz.
8. Measured in accordance with JEDEC standard 65.
9. Rj is multiplied by 14; estimate the pp jitter from Rj over 212 rising edges.
Rev. 1.5
13
Si5 338
Table 12. Jitter Specifications1,2,3 (Continued)
(VDD = 1.8 V –5% to +10%, 2.5 V ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
—
3
15
ps pk-pk
—
2
10
ps pk-pk
Output MultiSynth
operated in fractional
mode7
—
13
36
ps pk-pk
Output MultiSynth
operated in integer
mode7
—
12
20
ps pk-pk
Output MultiSynth
operated in fractional
Deterministic Jitter
mode7
DJ
Output MultiSynth
operated in integer
7
mode
Total Jitter
(12 kHz–20 MHz)
TJ = DJ+14xRJ
(See Note 9)
Notes:
1. All jitter measurements apply for LVDS/HCSL/LVPECL/CML output format with a low noise differential input clock and
are made with an Agilent 90804 oscilloscope. All RJ measurements use RJ/DJ separation.
2. For best jitter performance, keep the single ended clock input slew rates at Pins 3 and 4 more than 1.0 V/ns and the
differential clock input slew rates more than 0.3 V/ns.
3. All jitter data in this table is based upon all output formats being differential. When single-ended outputs are used, there
is the potential that the output jitter may increase due to the nature of single-ended outputs. If your configuration
implements any single-ended output and any output is required to have jitter less than 3 ps rms, contact Silicon Labs
for support to validate your configuration and ensure the best jitter performance. In many configurations, CMOS
outputs have little to no effect upon jitter.
4. DJ for PCI and GbE is < 5 ps pp
5. Output MultiSynth in Integer mode.
6. All output clocks 100 MHz HCSL format. Jitter is from the PCIE jitter filter combination that produces the highest jitter.
See AN562 for details. Jitter is measured with the Intel Clock Jitter Tool, Ver. 1.6.4.
7. Input frequency to the Phase Detector between 25 and 40 MHz and any output frequency > 5 MHz.
8. Measured in accordance with JEDEC standard 65.
9. Rj is multiplied by 14; estimate the pp jitter from Rj over 212 rising edges.
Table 13. Jitter Specifications, Clock Buffer Mode (PLL Bypass)*
(VDD = 1.8 V –5% to +10%, 2.5 V ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Additive Phase Jitter
(12 kHz–20 MHz)
tRPHASE
0.7 V pk-pk differential input
clock at 622.08 MHz with
70 ps rise/fall time
—
0.165
—
ps RMS
Additive Phase Jitter
(50 kHz–80 MHz)
tRPHASEWB
0.7 V pk-pk differential input
clock at 622.08 MHz with
70 ps rise/fall time
—
0.225
—
ps RMS
*Note: All outputs are in Clock Buffer mode (PLL Bypass).
14
Rev. 1.5
Si5338
Table 14. Typical Phase Noise Performance
Offset Frequency
25 MHz XTAL
to 156.25 MHz
27 MHz Ref In
to 148.3517 MHz
19.44 MHz Ref In
to 155.52 MHz
Units
100 Hz
–90
–87
–110
dBc/Hz
1 kHz
–120
–117
–116
dBc/Hz
10 kHz
–126
–123
–123
dBc/Hz
100 kHz
–132
–130
–128
dBc/Hz
1 MHz
–132
–132
–128
dBc/Hz
10 MHz
–145
–145
–145
dBc/Hz
Table 15. I2C Specifications (SCL,SDA)1
Parameter
Symbol
LOW Level
Input Voltage
VILI2C
HIGH Level
Input Voltage
VIHI2C
Hysteresis of
Schmitt Trigger
Inputs
VHYS
Test Condition
Standard Mode
Fast Mode
Unit
Min
Max
Min
Max
–0.5
0.3 x VDDI2
–0.5
0.3 x VDDI2C2
V
3.63
0.7 x VDDI2C2
3.63
V
N/A
N/A
0.1
—
V
VDDI2C2 = 2.5/3.3 V
0
0.4
0
0.4
V
VDDI2C2 = 1.8 V
N/A
N/A
0
0.2 x VDDI2C
V
–10
10
–10
10
μA
C
0.7 x VDDI2
C
LOW Level Out- VOLI2C2
put Voltage
(open drain or
open collector)
at 3 mA Sink
Current
Input Current
II2C
Capacitance for
each I/O Pin
CI2C
VIN = –0.1 to VDDI2C
—
4
—
4
pF
—
Timeout Enabled
25
35
25
35
ms
I2C Bus Timeout
Data Rate
Standard Mode
100
400
kbps
Notes:
1. Refer to NXP’s UM10204 I2C-bus specification and user manual, Revision 03, for further details:
www.nxp.com/acrobat_download/usermanuals/UM10204_3.pdf.
2. I2C pullup voltages (VDDI2C) of 1.71 to 3.63 V are supported. Must write register 27[7] = 1 if the I2C bus voltage is less
than 2.5 V to maintain compatibility with the I2C bus standard.
3. Hold time is defined as the time that data should hold its logical value after clock has transitioned to a logic low.
4. Guaranteed by characterization.
Rev. 1.5
15
Si5 338
Table 15. I2C Specifications (SCL,SDA)1 (Continued)
Parameter
Symbol
Test Condition
Standard Mode
Fast Mode
Unit
Hold Time
(Repeated)
START
Condition
tHD:STA
4.0
—
0.6
—
s
Set-Up Time for
a Repeated
START Condition
tSU:STA
4.7
—
0.6
—
s
Data Hold
Time3,4
tHD:DAT
100
—
100
—
ns
Data Set-Up
Time
tSU:DAT
250
—
150
—
ns
Notes:
1. Refer to NXP’s UM10204 I2C-bus specification and user manual, Revision 03, for further details:
www.nxp.com/acrobat_download/usermanuals/UM10204_3.pdf.
2. I2C pullup voltages (VDDI2C) of 1.71 to 3.63 V are supported. Must write register 27[7] = 1 if the I2C bus voltage is less
than 2.5 V to maintain compatibility with the I2C bus standard.
3. Hold time is defined as the time that data should hold its logical value after clock has transitioned to a logic low.
4. Guaranteed by characterization.
16
Rev. 1.5
Si5338
2. Typical Application Circuits
Rev. 1.5
17
Si5 338
3. Functional Description
Figure 1. Si5338 Block Diagram
3.1. Overview
The Si5338 is a high-performance, low-jitter clock
generator capable of synthesizing four independent
user-programmable clock frequencies up to 350 MHz
and select frequencies up to 710 MHz. The device
supports free-run operation using an external crystal, or
it can lock to an external clock for generating
synchronous clocks. The output drivers support four
differential clocks or eight single-ended clocks or a
combination of both. The output drivers are configurable
to support common signal formats, such as LVPECL,
LVDS, HCSL, CMOS, HSTL, and SSTL. Separate
output supply pins allow supply voltages of 3.3, 2.5, 1.8,
and 1.5 V to support the multi-format output driver. The
core voltage supply accepts 3.3, 2.5, or 1.8 V and is
independent from the output supplies.
Using its two-stage synthesis architecture and patented
high-resolution MultiSynth technology, the Si5338 can
generate four independent frequencies from a single
input frequency. In addition to clock generation, the
inputs can bypass the synthesis stage enabling the
Si5338 to be used as a high-performance clock buffer or
a combination of a buffer and generator.
For applications that need fine frequency adjustments,
such as clock margining, each of the synthesized
frequencies can be incremented or decremented in
user-defined steps as low as 1 ppm per step.
Output-to-output phase delays are also adjustable in
user-defined steps with an error of <20 ps to
compensate for PCB trace delays or for fine tuning of
setup and hold margins.
18
A zero-delay mode is also available to help minimize
input-to-output delay. Spread spectrum is available on
each of the clock outputs for EMI-sensitive applications,
such as PCI Express.
Configuration and control of the Si5338 is mainly
handled through the I2C/SMBus interface. Some
features, such as output enable and frequency or phase
adjustments, can optionally be pin controlled. The
device has a maskable interrupt pin that can be
monitored for loss of lock or loss of input signal
conditions.
The device also provides the option of storing a userdefinable clock configuration in its non-volatile memory
(NVM), which becomes the default clock configuration
at power-up.
3.1.1. ClockBuilder™ Desktop Software
To simplify device configuration, Silicon Labs provides
ClockBuilder Desktop software, which can operate
stand alone or in conjunction with the Si5338 EVB.
When the software is connected to an Si5338 EVB it will
control both the supply voltages to the Si5338 as well as
the entire clock path within the Si5338. Clockbuilder
Desktop can also measure the current delivered by the
EVB regulators to each supply voltage of the Si5338. A
Si5338 configuration can be written to a text file to be
used by any system to configure the Si5338 via I2C.
ClockBuilder Desktop can be downloaded from
www.silabs.com/ClockBuilder and runs on Windows XP,
Windows Vista, and Windows 7.
Rev. 1.5
Si5338
3.2. Input Stage
The input stage supports four inputs. Two are used as
the clock inputs to the synthesis stage, and the other
two are used as feedback inputs for zero delay or
external feedback mode. In cases where external
feedback is not required, all four inputs are available to
the synthesis stage. The reference selector selects one
of the inputs as the reference to the synthesis stage.
The input configuration is selectable through the IC
interface. The input MUXes are set automatically in
ClockBuilder Desktop (see “3.1.1. ClockBuilder™
Desktop Software”). For information on setting the input
MUXs manually, see the Si5338 Reference Manual:
Configuring the Si5338 without ClockBuilder Desktop.
IN3 and IN4 accept single-ended signals from 5 MHz to
200 MHz. The single-ended inputs are internally accoupled; so, they can accept a wide variety of signals
without requiring a specific dc level. The input signal
only needs to meet a minimum voltage swing and must
not exceed a maximum VIH or a minimum VIL. Refer to
Table 6 for signal voltage limits. A typical single-ended
connection is shown in Figure 3. For additional
termination options, refer to “AN408: Termination
Options for Any-Frequency, Any-Output Clock
Generators and Clock Buffers—Si5338, Si5334,
Si5330”.
For free-run operation, the internal oscillator can
operate from a low-frequency fundamental mode crystal
(XTAL) with a resonant frequency between 8 and
30 MHz. A crystal can easily be connected to pins IN1
and IN2 without external components as shown in
Figure 4. See Tables 8–11 for crystal specifications that
are guaranteed to work with the Si5338.
Figure 4. Connecting an XTAL to the Si5338
Figure 2. Input Stage
IN1/IN2 and IN5/IN6 are differential inputs capable of
accepting clock rates from 5 to 710 MHz. The
differential inputs are capable of interfacing to multiple
signals, such as LVPECL, LVDS, HSCT, HCSL, and
CML. Differential signals must be ac-coupled as shown
in Figure 3. A termination resistor of 100  placed close
to the input pins is also required. Refer to Table 6 for
signal voltage limits.
Refer to “AN360: Crystal Selection Guide for Si533x/5x
Devices” for information on the crystal selection.
3.2.1. Loss-of-Signal (LOS) Alarm Detectors
There are two LOS detectors: LOS_CLKIN and
LOS_FDBK. These detectors are tied to the outputs of
the P1 and P2 frequency dividers, which are always
enabled. See "3.6. Status Indicators" on page 24 for
details on the alarm indicators. These alarms are used
during programming to ensure that a valid input clock is
detected. The input MUXs are set automatically in
ClockBuilder Desktop (see the Si5338 Reference
Manual to set manually).
3.3. Synthesis Stages
Figure 3. Interfacing Differential and SingleEnded Signals to the Si5338
Next-generation timing applications require a wide
range of frequencies that are often non-integer related.
Traditional clock architectures address this by using
multiple single PLL ICs, often at the expense of BOM
complexity and power. The Si5338 uses patented
MultiSynth technology to dramatically simplify timing
architectures by integrating the frequency synthesis
capability of four Phase-Locked Loops (PLLs) in a
single device, greatly reducing size and power
requirements versus traditional solutions.
Rev. 1.5
19
Si5 338
Synthesis of the output clocks is performed in two
stages, as shown in Figure 5. The first stage consists of
a high-frequency analog phase-locked loop (PLL) that
multiplies the input stage to a frequency within the
range of 2.2 to 2.84 GHz. Multiplication of the input
frequency is accomplished using a proprietary and
highly precise MultiSynth feedback divider (N), which
allows the PLL to generate any frequency within its
VCO range with much less jitter than typical fractional N
PLL.
Figure 5. Synthesis Stages
The second stage of synthesis consists of the output
MultiSynth dividers (MSx). Based on a fractional N
divider, the MultiSynth divider shown in Figure 6
switches seamlessly between the two closest integer
divider values to produce the exact output clock
frequency with 0 ppm error.
To eliminate phase error generated by this process, the
MultiSynth block calculates the relative phase difference
between the clock produced by the fractional-N divider
and the desired output clock and dynamically adjusts
the phase to match the ideal clock waveform. This novel
approach makes it possible to generate any output
clock frequency without sacrificing jitter performance.
This architecture allows the output of each MultiSynth to
produce any frequency from 5 to Fvco/8 MHz. To
support higher frequency operation, the MultiSynth
divider can be bypassed. In bypass mode, integer divide
ratios of 4 and 6 are supported. This allows for output
frequencies of Fvco/4 and Fvco/6 MHz, which translates
to 367–473.33 MHz and 550–710 MHz respectively.
Because each MultiSynth uses the same VCO output,
there are output frequency limitations when output
frequencies greater than Fvco/8 are desired.
For example, if 375 MHz is needed at the output of
MultiSynth0, the VCO frequency would need to be
2.25 GHz. Now, all the other MultiSynths can produce
any frequency from 5 MHz up to a maximum frequency
of 2250/8 = 281.25 MHz. MultiSynth1,2,3 could also
produce Fvco/4 = 562.5 MHz or Fvco/6 = 375 MHz. Only
two unique frequencies above Fvco/8 can be output:
Fvco/6 and Fvco/4.
Figure 6. Silicon Labs’ MultiSynth Technology
20
Rev. 1.5
Si5338
3.4. Output Stage
The output stage consists of output selectors, output
dividers, and programmable output drivers as shown in
Figure 7.
Each of the outputs can also be enabled or disabled
through the I2C port. A single pin to enable/disable all
outputs is available in the Si5338K/L/M.
3.5. Configuring the Si5338
The Si5338 is a highly-flexible clock generator that is
entirely configurable through its I2C interface. The
device’s default configuration is stored in non-volatile
memory (NVM) as shown in Figure 8. The NVM is a
one-time programmable memory (OTP), which can
store a custom user configuration at power-up. This is a
useful feature for applications that need a clock present
at power-up (e.g., for providing a clock to a processor).
Figure 7. Output Stage
The output selectors select the clock source for the
output drivers. By default, each output driver is
connected to its own MultiSynth block (e.g. MS0 to
CLK0, MS1 to CLK1, etc), but other combinations are
possible by reconfiguring the device. The PLL can be
bypassed by connecting the input stage signals (osc,
ref, refdiv, fb, or fbdiv) directly to the output divider.
Bypassing an input directly to an output will not allow
phase alignment of that output to other outputs. Each of
the output drivers can also connect to the first
MultiSynth block (MS0) enabling a fan-out function. This
allows the Si5338 to act as a clock generator, a fanout
buffer, or a combination of both in the same package.
The output dividers (R0, R1, R2, R3) allow another
stage of clock division.These dividers are configurable
as divide by 1 (default), 2, 4, 8, 16, or 32. When an Rn
does not equal 1, the phase alignment function for that
output will not work.
The output drivers are configurable to support common
signal formats, such as LVPECL, LVDS, HCSL, CMOS,
HSTL, and SSTL. Separate output supply pins (VDDOn)
are provided for each output buffer.
The voltage on these supply pins can be 3.3, 2.5, 1.8, or
1.5 V as needed for the possible output formats.
Additionally, the outputs can be configured to stop high,
low, or tri-state when the PLL has lost lock. If the Si5338
is used in a zero delay mode, the output that is fed back
must be set for always on, which will override any
output disable signal.
Figure 8. Si5338 Memory Configuration
During a power cycle or a power-on reset (POR), the
contents of the NVM are copied into random access
memory (RAM), which sets the device configuration that
will be used during operation. Any changes to the
device configuration after power-up are made by
reading and writing to registers in the RAM space
through the I2C interface. ClockBuilder Desktop (see
"3.1.1. ClockBuilder™ Desktop Software" on page 18)
can be used to easily configure register map files that
can be written into RAM (see “3.5.2. Creating a New
Configuration for RAM” for details). Alternatively, the
register map file can be created manually with the help
of the equations in the Si5338 Reference Manual.
Two versions of the Si5338 are available. First,
standard, non-customized Si5338 devices are available
in which the RAM can be configured in-circuit via I2C
(example part number Si5338C-A-GM). Alternatively,
standard Si5338 devices can be field-programmed
using the Si5338/56-PROG-EVB field programmer.
Second, custom factory-programmed Si5338 devices
are available that include a user-specified startup
frequency configuration (example part number
Si5338C-Axxxxx-GM). See "12. Ordering Information"
on page 42 for details.
Rev. 1.5
21
Si5 338
3.5.1. Ordering a Custom NVM Configuration
The Si5338 is orderable with a factory-programmed custom NVM configuration. This is the simplest way of using
the Si5338 since it generates the desired output frequencies at power-up or after a power-on reset (POR). This
default configuration can be reconfigured in RAM through the I2C interface after power-up (see “3.5.2. Creating a
New Configuration for RAM”).
Custom 7-bit I2C addresses may also be requested. Note that for the A/B/C devices, the I2C LS bit address is the
logical “or” of the I2C address LS bit in Register 27 and the state of the I2C_LSB pin. If I2C_LSB pin functionality is
required, custom I2C addresses may only be even numbers. For all other variants of the device, custom I2C
addresses may be even or odd numbers. See the Si5338 Reference Manual: Configuring the Si5338 without
ClockBuilder Desktop for more details.
The first step in ordering a custom device is generating an NVM file which defines the input and output clock
frequencies and signal formats. This is easily done using the ClockBuilder Desktop software (see "3.1.1.
ClockBuilder™ Desktop Software" on page 18). This GUI based software generates an NVM file, which is used by
the factory to manufacture custom parts. Each custom part is marked with a unique part number identifying the
specific configuration (e.g., Si5338C-A00100-GM). Consult your local sales representative for more details on
ordering a custom Si5338.
3.5.2. Creating a New Configuration for RAM
Any Si5338 device can be configured by writing to registers in RAM through the I2C interface. A non-factory
programmed device must be configured in this manner.
The first step is to determine all the register values for the required configuration. This can be accomplished by one
of two methods.
1. Create a device configuration (register map) using ClockBuilder Desktop (v3.0 or later; see "3.1.1.
ClockBuilder™ Desktop Software" on page 18).
a. Configure the frequency plan.
b. Configure the output driver format and supply voltage.
c. Configure frequency and/or phase inc/dec (if desired).
d. Configure spread spectrum (if desired).
e. Configure for zero-delay mode (if desired, see "3.10.6. Zero-Delay Mode" on page 28).
f. If needed go to the Advanced tab and make additional configurations.
g. Save the configuration using the Options > Save Register Map File or Options > Save C code Header.
2. Create a device configuration, register by register, using the Si5338 Reference Manual.
3.5.3. Writing a Custom Configuration to RAM
Writing a new configuration (register map) to the RAM consists of pausing the LOL state-machine, writing new
values to the IC accounting for the write-allowed mask (see the Si5338 Reference Manual, “10. Si5338 Registers”),
validating the input clock or crystal, locking the PLL to the input with the new configuration, restarting the LOL
state-machine, and calibrating the VCO for robust operation across temperature. The flow chart in Figure 9
enumerates the details:
Note: The write-allowed mask specifies which bits must be read and modified before writing the entire register byte (a.k.a.
read-modify-write). “AN428: Jump Start: In-System, Flash-Based Programming for Silicon Labs’ Timing Products” illustrates the procedure defined in Section 3.5.2 with ANSI C code.
22
Rev. 1.5
Si5338
Figure 9. I2C Programming Procedure
Rev. 1.5
23
Si5 338
3.5.4. Writing a Custom Configuration to NVM
An alternative to ordering an Si5338 with a custom NVM
configuration is to use the field programming kit
(Si5338/56-PROG-EVB) to write directly to the NVM of
a “blank” Si5338. Since NVM is an OTP memory, it can
only be written once. The default configuration can be
reconfigured by writing to RAM through the I2C interface
(see “3.5.2. Creating a New Configuration for RAM”).
3.6. Status Indicators
Figure 11. INTR Pin with Required Pull-Up
A logic-high interrupt pin (INTR) is available to indicate
a loss of signal (LOS) condition, a PLL loss of lock
(PLL_LOL) condition, or that the PLL is in process of
acquiring lock (SYS_CAL). PLL_LOL is held high when
the input frequency drifts beyond the PLL tracking
range. It is held low during all other times and during a
POR or soft_reset. SYS_CAL is held high during a POR
or SOFT reset so that no chattering occurs during the
locking process. As shown in Figure 10, a status
register at address 218 is available to help identify the
exact event that caused the interrupt pin to become
active. Register 247 is the sticky version of Register
218, and Register 6 is the interrupt mask for Register
218.
3.7. Output Enable
There are two methods of enabling and disabling the
output drivers: Pin control, and I2C control.
3.7.1. Enabling Outputs Using Pin Control
The Si5338K/L/M devices provide an Output Enable pin
(OEB) as shown in Figure 12. Pulling this pin high will
turn all outputs off. The state of the individual drivers
when turned off is controllable. If an individual output is
set to always on, then the OEB pin will not have an
effect on that driver. Drive state options and always on
are explained in “3.7.2. Enabling Outputs through the
I2C Interface”.
Figure 12. Output Enable Pin (Si5338K/L/M)
Figure 10. Status Register
Figure 11 shows a typical connection with the required
pull-up resistor to VDD.
3.6.1. Using the INTR Pin in Systems with I2C
The INTR output pin is not latched and thus it should not
be a polled input to an MCU but an edge-triggered
interrupt. An MCU can process an interrupt event by
reading the sticky register 247 to see what event
caused the interrupt. The same register can be cleared
by writing zeros to the bits that were set. Individual
interrupt bits can be masked by register 6[4:0].
3.6.2. Using the INTR Pin in Systems without I2C
The INTR pin also provides a useful function in systems
that require a pin-controlled fault indicator. Pre-setting
the interrupt mask register allows the INTR pin to
become an indicator for a specific event, such as LOS
and/or LOL. Therefore, the INTR pin can be used to
indicate a single fault event or even multiple events.
24
3.7.2. Enabling Outputs through the I2C Interface
Output enable can be controlled through the I2C
interface. As shown in Figure 13, register 230[3:0]
allows control of each individual output driver. Register
230[4] controls all drivers at once. When register 230[4]
is set to disable all outputs, the individual output
enables will have no effect. Registers 110[7:6], 114[7:6],
118[7:6], and 112[7:6] control the output disabled state
as tri-state, low, high, or always on. If always on is set,
that output will always be on regardless of any other
register or chip state. In addition, the always on mode
must be selected for an output that is fed back in a Zero
Delay application.
Rev. 1.5
Si5338
SSTL, it is required to have load circuitry as shown in
“AN408: Termination Options for Any-Frequency, AnyOutput Clock Generators and Clock Buffers”. The
Si5338 EVB has layout pads that can be used for this
purpose. When testing for output driver current with
LVPECL the same layout pads can be used to
implement the LVPECL bias resistor of 130  (2.5 V
VDDx) or 200  (3.3 V VDDx). See the schematic in the
Si5338-EVB data sheet and AN408 for additional
information.
Figure 13. Output Enable Control Registers
3.8. Power Consumption
The Si5338 Power consumption is a function of
 Supply voltage
 Frequency of output Clocks
 Number of output Clocks
 Format of output Clocks
Because of internal voltage regulation, the current from
the core VDD is independent of the VDD voltage and
hence the plot shown in Figure 14 can be used to
estimate the VDD core (pins 7 and 24) current.
The current from the output supply voltages can be
estimated from the values provided in Table 3, “DC
Characteristics,” on page 5. To get the most accurate
value for VDD currents, the Si5338-EVB with
Clockbuilder software should be used. To do this, go to
the “Power” tab of the Clockbuilder and press
“Measure”. In this manner, a specific configuration can
be implemented on the EVB and the actual current for
each supply voltage measured. When doing this it is
critical that the output drivers have the proper load
impedance for the selected format.
When testing for output driver current with HSTL and
Rev. 1.5
25
Si5 338
80
4 Active Outputs, Fractional Output MS
75
4 Active Outputs, Integer Output MS
3 Active Outputs, Fractional Output MS
70
Typical VDD Core Current (ma)
3 Active Outputs, Integer Output MS
2 Active Outputs, Fractional Output MS
65
2 Active Outputs, Integer Output MS
1 Active Output, Fractional Output MS
60
1 Active Output, Integer Output MS
55
50
45
40
35
30
0
50
100
150
200
250
300
Output Frequency (MHz)
Figure 14. Core VDD Supply Average Current vs Output Frequency
26
Rev. 1.5
350
400
Si5338
3.9. Reset Options
There are two types of resets on the Si5338, POR and
soft reset. A POR reset automatically occurs whenever
the supply voltage on the VDD is applied.
The soft reset is forced by writing 0x02 to register 246.
This bit is not self-clearing, and thus it may read back as
a 1 or a 0. A soft reset will not download any preprogrammed NVM and will not change any register
values in RAM.
The soft reset performs the following sequence:
1. All outputs turn off except if programmed to be
always on.
2. Internal calibrations are done and MultiSynths are
initialized.
a. Outputs that are synchronous are phase
aligned (if Rn = 1).
3. 25 ms is allowed for the PLL to lock (no delay occurs
when FCAL_OVRD_EN = 1).
4. Turn on all outputs that were turned off in step 1.
3.10. Features of the Si5338
The Si5338 offers several features and functions that
are useful in many timing applications. The following
paragraphs describe in detail the main features and
typical applications. All of these features can be easily
configured using the ClockBuilder Desktop. See "3.1.1.
ClockBuilder™ Desktop Software" on page 18.
3.10.1. Frequency Increment/Decrement
Each of the output clock frequencies can be
independently stepped up or down in predefined steps
as low as 1 ppm per step and with a resolution of
1 ppm. Setting of the step size and control of the
frequency increment or decrement is accomplished
through the I2C interface. Alternatively, the Si5338 can
be ordered with optional frequency increment (FINC)
and frequency decrement (FDEC) pins for pincontrolled applications. Note that FINC and FDEC pins
only affect CLK0. Frequency increment and decrement
of all other channels must be performed by I2C writes to
the appropriate registers. See Table 17 on page 37 for
ordering information of pin-controlled devices. When
phase is decremented, the MultiSynth output clock edge
will happen sooner which will create a single half cycle
that is shorter than expected for the MultiSynth output
clock frequency. Care must be taken to insure that a
single phase decrement does not produce a half cycle
that is less than 4/fvco or an unwanted glitch in the
MultiSynth output may occur.
The frequency increment and decrement feature is
useful in applications requiring a variable clock
frequency (e.g., CPU speed control, FIFO overflow
management, etc.) or in applications where frequency
margining (e.g., fout ±5%) is necessary for design
verification and manufacturing test. Frequency
increment or decrement can be applied as fast as
1.5 MHz when it is done by pin control. When under I2C
control, the frequency increment and decrement update
rate is limited by the I2C bus speed. The magnitude of
the frequency step has 0 ppm error. Frequency steps
are seamless and glitchless.
If a frequency increment/decrement command causes
the MultiSynth output frequency to exceed the
maximum/minimum limits, then a glitch on the output is
likely to occur. The max frequency of a MultiSynth
output that is using frequency increment/decrement is
Fvco/8, and the minimum frequency is 5 MHz.
3.10.2. Output Phase Increment/Decrement
The Si5338 has a digitally-controlled glitchless phase
increment and decrement feature that allows adjusting
the phase of each output clock in relation to the other
output clocks. The phase of each output clock can be
adjusted with an accuracy of 20 ps over a range of
±45 ns. Setting of the step size and control of the phase
increment or decrement is accomplished through the
I2C interface. Alternatively, the Si5338 can be ordered
with optional phase increment (PINC) and phase
decrement (PDEC) pins for pin-controlled applications.
In pin controlled applications the phase increment and
decrement update rate is as fast as 1.5 MHz. In I2C
applications, the maximum update rate is limited by the
speed of the I2C. See Table 17 for ordering information
of pin-controlled devices. When phase is decremented,
the MultiSynth output clock edge will happen sooner,
which will create a single half cycle that is shorter than
expected for the MultiSynth output clock frequency.
Care must be taken to insure that a single phase
decrement does not produce a half cycle that is less
than 4/fvco or an unwanted glitch in the MultiSynth
output may occur.
The phase increment and decrement feature provides a
useful method for fine tuning setup and hold timing
margins or adjusting for mismatched PCB trace lengths.
3.10.3. Programmable Initial Phase Offset
Each output clock can be set for its initial phase offset
up to ±45 ns. In order for the initial phase offset to be
applied correctly at power up, the VDDOx output supply
voltage must cross 1.2 V before the VDD (pins 7,24)
core power supply voltage crosses 1.45 V. This applies
to the each driver output individually. A soft_reset will
also guarantee that the programmed Initial Phase Offset
is applied correctly. The initial phase offset only works
on outputs that have their R divider set to 1.
Rev. 1.5
27
Si5 338
3.10.4. Output Synchronization
Upon power up or a soft_reset the Si5338 synchronizes
the output clocks. With normal output polarity (no output
clock inversion), the Si5338 synchronizes the output
clocks to the falling, not rising edge. Synchronization at
the rising edge can be done by inverting all the clocks
that are to be synchronized.
3.10.5. Output R Divider
When the requested output frequency of a channel is
below 5 MHz, the Rn (n = 0,1,2,3) divider needs to be
set and enabled. This is automatically done in register
maps generated by the ClockBuilder Desktop. When
the Rn divider is active the step size range of the
frequency increment and decrement function will
decrease by the Rn divide ratio. The Rn divider can be
set to {1, 2, 4, 8, 16, 32}.
Non-unity settings of R0 will affect the Finc/Fdec step
size at the MultiSynth0 output. For example, if the
MultiSynth0 output step size is 2.56 MHz and R0 = 8,
the step size at the output of R0 will be 2.56 MHz
divided by 8 = .32 MHz. When the Rn divider is set to
non-unity, the initial phase offset of the CLKn output with
respect to other CLKn outputs is not guaranteed.
3.10.6. Zero-Delay Mode
The Si5338 supports an optional zero delay mode of
operation for applications that require minimal input-tooutput delay. In this mode, one of the device output
clocks is fed back to the feedback input pin (IN4 or IN5/
IN6) to implement an external feedback path which
nullifies the delay between the reference input and the
output clocks. Figure 15 shows the Si5338 in a typical
zero-delay configuration. It is generally recommended
that Clk3 be LVDS and that the feedback input be pins 5
and 6. For the differential input configuration to pins 5
and 6, see Figure 3 on page 19. The zero-delay mode
combined with the phase increment/decrement feature
allows unprecedented flexibility in generating clocks
with precise edge alignment.
Figure 15. Si5338 in Zero Delay Clock
Generator Mode
3.10.7. Spread Spectrum
To help reduce electromagnetic interference (EMI), the
Si5338 supports spread spectrum modulation. The
output clock frequencies can be modulated to spread
energy across a broader range of frequencies, lowering
system EMI. The Si5338 implements spread spectrum
using its patented MultiSynth technology to achieve
previously unattainable precision in both modulation
rate and spreading magnitude as shown in Figure 16.
Through I2C control, the Spread spectrum can be
applied to any output clock, any clock frequency, and
any spread amount from ±0.1% to ±2.5% center spread
and –0.1% to –5% down spread.
The spreading rate is limited to 30 to 63 kHz.
The Spread Spectrum is generated digitally in the output
MultiSynths which means that the Spread Spectrum
parameters are virtually independent of process,
voltage and temperature variations. Since the Spread
Spectrum is created in the output MultiSynths, through
I2C each output channel can have independent Spread
Spectrum parameters. Without the use of I2C (NVM
download only) the only supported Spread Spectrum
parameters are for PCI Express compliance composing
100 MHz clock, 31.5 kHz spreading frequency with the
choice of the spreading.
Rev A devices provide native support for both down and
center spread. Center spread is supported in rev B
devices by up-shifting the nominal frequency and using
down-spread register parameters. Consult the Si5338
Reference Manual for details.
Note: If you currently use center spread on a revision A and
would like to migrate to a revision B device, you must
generate a new register map using either ClockBuilder
Desktop or the equations in the Si5338 Reference
Manual. Center spread configurations for Revisions A
and B are not compatible.
28
Rev. 1.5
Si5338
4. Applications of the Si5338
+/- 0%
+/- 1%
+/- 2.5%
+/- 5%
Because of its flexible architecture, the Si5338 can be
configured to serve several functions in the timing path.
The following sections describe some common
applications.
4.1. Free-Running Clock Generator
Figure 16. Configurable Spread Spectrum
Using the internal oscillator (Osc) and an inexpensive
external crystal (XTAL), the Si5338 can be configured
as a free-running clock generator for replacing high-end
and long-lead-time crystal oscillators found on many
printed circuit boards (PCBs). Replacing several crystal
oscillators with a single IC solution helps consolidate the
bill of materials (BOM), reduces the number of
suppliers, and reduces the number of long-lead-time
components on the PCB. In addition, since crystal
oscillators tend to be the least reliable aspect of many
systems, the overall FIT rate improves with the
elimination of each oscillator.
Up to four independent clock frequencies can be
generated at any rate within its supported frequency
range and with any of supported output types. Features,
such as frequency increment and decrement and phase
adjustments on a per-output basis, provide
unprecedented flexibility for PCB designs. Figure 17
shows the Si5338 configured as a free-running clock
generator.
Figure 17. Si5338 as a Free-Running Clock
Generator
Rev. 1.5
29
Si5 338
4.2. Synchronous Frequency Translation
4.3. Configurable Buffer and Level Translator
In other cases, it is useful to generate an output
frequency that is synchronous (or phase-locked) to
another clock frequency. The Si5338 is the ideal choice
for generating up to four clocks with different
frequencies with a fixed phase relationship to an input
reference. Because of its highly precise frequency
synthesis, the Si5338 can generate all four output
frequencies with 0 ppm error to the input reference. The
Si5338 is an ideal choice for applications that have
traditionally required multiple stages of frequency
synthesis to achieve complex frequency translations.
Examples are in broadcast video (e.g., 148.5 MHz to
148.351648351648 MHz), WAN/LAN applications (e.g.
155.52 MHz to 156.25 MHz), and Forward Error
Correction (FEC) applications (e.g., 156.25 MHz to
161.1328125 MHz). Using the input reference selectors,
the Si5338 can select from one of four inputs (IN1/IN2,
IN3, IN4, and IN5/IN6). Figure 18 shows the Si5338
configured as a synchronous clock generator.
Frequencies and multiplication ratios may be entered
into ClockBuilder Desktop using fractional notation to
ensure that the exact scaling ratios can be achieved.
Using the output selectors, the synthesis stage can be
entirely bypassed allowing the Si5338 to act as a
configurable clock buffer/divider with level translation
and selectable inputs. Because of its highly selectable
configuration, virtually any combination is possible. The
configurable output drivers allow four differential
outputs, eight single-ended outputs, or a combination of
both. Figure 19 shows the Si5338 configured as a
flexible clock buffer.
Figure 19. Si5338 as a Configurable Clock
Buffer/Divider with Level Translation
4.3.1. Combination Free-Running and Synchronous
Clock Generator
Another application of the Si5338 is in generating both
free-running and synchronous clocks in one device.
This is accomplished by configuring the input and
output selectors for the desired split configuration. An
example of such an application is shown in Figure 20.
Figure 18. Si5338 as a Synchronous Clock
Generator or Frequency Translator
Figure 20. Si5338 In a Free-Running and
Synchronous Clock Generator Application
30
Rev. 1.5
Si5338
5. I2C Interface
Configuration and operation of the Si5338 is controlled
by reading and writing to the RAM space using the I2C
interface. The device operates in slave mode with 7-bit
addressing and can operate in Standard-Mode
(100 kbps) or Fast-Mode (400 kbps) and supports burst
data transfer with auto address increments.
The I2C bus consists of a bidirectional serial data line
(SDA) and a serial clock input (SCL) as shown in
Figure 21. Both the SDA and SCL pins must be
connected to the VDD supply via an external pull-up as
recommended by the I2C specification.
Figure 23. I2C Write Operation
A read operation is performed in two stages. A data
write is used to set the register address, then a data
read is performed to retrieve the data from the set
address. A read burst operation is also supported. This
is shown in Figure 24.
Figure 21. I2C and Control Signals
The 7-bit device (slave) address of the Si5338 consists
of a 6-bit fixed address plus a user-selectable LSB bit as
shown in Figure 22. The LSB bit is selectable using the
optional I2C_LSB pin which is available as an ordering
option for applications that require more than one
Si5338 on a single I2C bus. Devices without the
I2C_LSB pin option have a fixed 7-bit address of 70h
(111 0000) as shown in Figure 22. Other custom I2C
addresses are also possible. See Table 17 for details
on device ordering information with the optional
I2C_LSB pin.
Figure 24. I2C Read Operation
Figure 22. Si5338 I2C Slave Address
Data is transferred MSB first in 8-bit words as specified
by the I2C specification. A write command consists of a
7-bit device (slave) address + a write bit, an 8-bit
register address, and 8 bits of data as shown in
Figure 23. A write burst operation is also shown where
every additional data word is written using an autoincremented address.
AC and dc electrical specifications for the SCL and SDA
pins are shown in Table 15. The timing specifications
and timing diagram for the I2C bus are compatible with
the I2C-Bus Standard. SDA timeout is supported for
compatibility with SMBus interfaces.
The I2C bus can be operated at a bus voltage of 1.71 to
3.63 V and is 3.3 V tolerant. If a bus voltage of less than
2.5 V is used, register 27[7] = 1 must be written to
maintain compatibility with the I2C bus standard.
Rev. 1.5
31
Si5 338
6. Si5338 Registers
For many applications, the Si5338's register values are easily configured using ClockBuilder Desktop (see "3.1.1.
ClockBuilder™ Desktop Software" on page 18). However, for customers interested in using the Si5338 in operating
modes beyond the capabilities available with ClockBuilder™, refer to the Si5338 Reference Manual: Configuring
the Si5338 without ClockBuilder Desktop for a detailed description of the Si5338 registers and their usage. Also
refer to “AN428: Jump Start: In-System, Flash-Based Programming for Silicon Labs’ Timing Products” for a working
application example using Silicon Labs' F301 MCU to program the Si5338 register set.
32
Rev. 1.5
Si5338
7. Pin Descriptions
Note: Center pad must be tied to GND for normal operation.
Table 16. Si5338 Pin Descriptions
Pin #
1,2
Pin Name
IN1/IN2
I/O
I
Signal Type
Description
Multi
CLKIN/CLKINB.
These pins are used as the main differential clock input or as the
XTAL input. See "3.2. Input Stage" on page 19, Figure 3 and
Figure 4, for connection details. Clock inputs to these pins must be
ac-coupled. Keep the traces from pins 1,2 to the crystal as short as
possible and keep other signals and radiating sources away from
the crystal.
When not in use, leave IN1 unconnected and IN2 connected to
GND.
Rev. 1.5
33
Si5 338
Table 16. Si5338 Pin Descriptions (Continued)
Pin #
3
Pin Name
IN3
I/O
I
Signal Type
Description
Multi
This pin can have one of the following functions depending on the
part number:
CLKIN (for Si5338A/B/C and Si5338N/P/Q devices only)
Provides a high-impedance clock input for single ended clock
signals. This input should be dc-coupled as shown in “3.2. Input
Stage”, Figure 3.
If this pin is not used, it should be connected to ground.
PINC (for Si5338D/E/F devices only)
Used as the phase increment pin. See "3.10.2. Output Phase
Increment/Decrement" on page 27 for more details. Minimum
pulse width of 100 ns is required for proper operation. If this pin is
not used, it should be connected to ground.
FINC (for Si5338G/H/J devices only)
Used as the frequency increment pin. See "3.10.1. Frequency
Increment/Decrement" on page 27 for more details. Minimum
pulse width of 100 ns is required for proper operation. If this pin is
not used, it should be connected to ground.
OEB (for Si5338K/L/M devices only)
Used as an output enable pin. 0 = All outputs enabled; 1 = All
outputs disabled. By default, outputs are tri-stated when disabled.
This pin can have one of the following functions depending on the
part number
I2C_LSB (for Si5338A/B/C and Si5338K/L/M devices only)
4
34
IN4
I
Multi
This is the LSB of the Si5338 I2C address. 0 = I2C address
70h (111 0000), 1 = I2C address 71h (111 0001).
FDBK (for Si5338N/P/Q devices only)
Provides a high-impedance feedback input for single-ended clock
signals. This input should be dc-coupled as shown in “3.2. Input
Stage”, Figure 3. If this pin is not used, it should be connected to
ground.
PDEC (for Si5338D/E/F) devices only)
Used as the phase decrement pin. See “3.10.2. Output Phase
Increment/Decrement” for more details. Minimum pulse width of
100 ns is required for proper operation. If this pin is not used, it
should be connected to ground.
FDEC (for Si5338G/H/J devices only)
Used as the frequency decrement pin. See “3.10.1. Frequency
Increment/Decrement” for more details. Minimum pulse width of
100 ns is required for proper operation. If this pin is not used, it
should be connected to ground.
Rev. 1.5
Si5338
Table 16. Si5338 Pin Descriptions (Continued)
Pin #
5,6
7
8
9
10
11
12
13
14
Pin Name
IN5/IN6
VDD
INTR
CLK3B
CLK3A
VDDO3
SCL
CLK2B
CLK2A
I/O
I
VDD
O
O
O
VDD
I
O
O
Signal Type
Description
Multi
FDBK/FDBKB.
These pins can be used as a differential feedback input in zero
delay mode or as a secondary clock input. See section 3.2,
Figure 3, for termination details. See "3.10.6. Zero-Delay Mode" on
page 28 for zero delay mode set-up. Inputs to these pins must be
ac-coupled.
When not in use, leave IN5 unconnected and IN6 connected to
GND.
Supply
Core Supply Voltage.
This is the core supply voltage, which can operate from a 1.8, 2.5,
or 3.3 V supply. A 0.1 μF bypass capacitor should be located very
close to this pin.
Open Drain
Interrupt.
A typical pullup resistor of 1–4 k is used on this pin. This pin can
be pulled up to a supply voltage as high as 3.6 V regardless of the
other supply voltages on pins 7, 11, 15, 16, 20, and 24. The interrupt condition allows the pull up resistor to pull the output up to the
supply voltage.
Multi
Output Clock B for Channel 3.
May be a single-ended output or half of a differential output with
CLK3A being the other differential half. If unused, leave this pin
floating.
Multi
Output Clock A for Channel 3.
May be a single-ended output or half of a differential output with
CLK3B being the other differential half. If unused, leave this pin
floating.
Supply
LVCMOS
Output Clock Supply Voltage.
Supply voltage (3.3, 2.5, 1.8, or 1.5 V) for CLK3A,B. A 0.1 μF
capacitor must be located very close to this pin. If CLK3 is not
used, this pin must be tied to VDD (pin 7, 24).
I2C Serial Clock Input.
This is the serial clock input for the I2C bus. A pullup resistor at this
pin is required. Typical values would be 1–4 k. See the I2C bus
spec for more information. This pin is 3.3 V tolerant regardless of
the other supply voltages on pins 7, 11, 15, 16, 20, 24. See Register 27.
Multi
Output Clock B for Channel 2.
May be a single-ended output or half of a differential output with
CLK2A being the other differential half. If unused, leave this pin
floating.
Multi
Output Clock A for Channel 2.
May be a single-ended output or half of a differential output with
CLK2B being the other differential half. If unused, leave this pin
floating.
Rev. 1.5
35
Si5 338
Table 16. Si5338 Pin Descriptions (Continued)
Pin #
15
16
17
18
19
Pin Name
VDDO2
VDDO1
CLK1B
CLK1A
SDA
I/O
VDD
VDD
O
O
I/O
Signal Type
Description
Supply
Output Clock Supply Voltage.
Supply voltage (3.3, 2.5, 1.8, or 1.5 V) for CLK2A,B.
A 0.1 μF capacitor must be located very close to this pin. If CLK2 is
not used, this pin must be tied to VDD (pin 7, 24).
Supply
Output Clock Supply Voltage.
Supply voltage (3.3, 2.5, 1.8, or 1.5 V) for CLK1A,B.
A 0.1 μF capacitor must be located very close to this pin. If CLK1 is
not used, this pin must be tied to VDD (pin 7, 24).
Multi
Output Clock B for Channel 1.
May be a single-ended output or half of a differential output with
CLK1A being the other differential half. If unused, leave this pin
floating.
Multi
Output Clock A for Channel 1.
May be a single-ended output or half of a differential output with
CLK1B being the other differential half. If unused, leave this pin
floating.
LVCMOS
I2C Serial Data.
This is the serial data for the I2C bus. A pullup resistor at this pin is
required. Typical values would be 1–4 k. See the I2C bus spec
for more information. This pin is 3.3 V tolerant regardless of the
other supply voltages on pins 7, 11, 15, 16, 20, 24. See Register
27.
Output Clock Supply Voltage.
Supply voltage (3.3, 2.5, 1.8, or 1.5 V) for CLK0A,B.
A 0.1 μF capacitor must be located very close to this pin. If CLK0 is
not used, this pin must be tied to VDD (pin 7, 24).
20
VDDO0
VDD
Supply
21
CLK0B
O
Multi
Output Clock B for Channel 0.
May be a single-ended output or half of a differential output with
CLK0A being the other differential half. If unused, leave this pin
floating.
22
CLK0A
O
Multi
Output Clock A for Channel 0.
May be a single-ended output or half of a differential output with
CLK0B being the other differential half. If unused, leave this pin
floating.
23
RSVD_GND
GND
GND
Ground.
Must be connected to system ground. Minimize the ground path
impedance for optimal performance of this device.
24
VDD
VDD
Supply
GND
PAD
GND
GND
GND
36
Core Supply Voltage.
The device operates from a 1.8, 2.5, or 3.3 V supply. A 0.1 μF
bypass capacitor should be located very close to this pin.
Ground Pad.
This is the large pad in the center of the package. Device
specifications cannot be guaranteed unless the ground pad is
properly connected to a ground plane on the PCB. See Table 19,
“PCB Land Pattern,” on page 40 for ground via requirements.
Rev. 1.5
Si5338
8. Device Pinout by Part Number
The Si5338 is orderable in three different speed grades: Si5338A/D/G/K/N have a maximum output clock
frequency limit of 710 MHz. Si5338B/E/H/L/P have a maximum output clock frequency of 350 MHz. Si5338C/F/J/
M/Q have a maximum output clock frequency of 200 MHz.
Devices are also orderable according to the pin control functions available on Pins 3 and 4:
 CLKIN—single-ended clock input







I2C_LSB—determines the LSB bit of the 7-bit I2C address
FINC—frequency increment pin
FDEC—frequency decrement pin
PINC—phase increment pin
PDEC—phase decrement pin
FDBK—single-ended feedback input
OEB—output enable
Table 17. Pin Function by Part Number
Pin #
Si5338A: 710 MHz Si5338D: 710 MHz Si5338G: 710 MHz Si5338K: 710 MHz Si5338N: 710 MHz
Si5338B: 350 MHz Si5338E: 350 MHz Si5338H: 350 MHz Si5338L: 350 MHz Si5338P: 350 MHz
Si5338C: 200 MHz Si5338F: 200 MHz Si5338J: 200 MHz Si5338M: 200 MHz Si5338Q: 200 MHz
1
CLKIN1
CLKIN1
CLKIN1
CLKIN1
CLKIN1
2
CLKINB1
CLKINB1
CLKINB1
CLKINB1
CLKINB1
3
CLKIN2
PINC
FINC
OEB
CLKIN2
4
I2C_LSB
PDEC
FDEC
I2C_LSB
FDBK3
5
FDBK4
FDBK4
FDBK4
FDBK4
FDBK4
6
FDBKB4
FDBKB4
FDBKB4
FDBKB4
FDBKB4
7
VDD
VDD
VDD
VDD
VDD
8
INTR
INTR
INTR
INTR
INTR
9
CLK3B
CLK3B
CLK3B
CLK3B
CLK3B
10
CLK3A
CLK3A
CLK3A
CLK3A
CLK3A
11
VDDO3
VDDO3
VDDO3
VDDO3
VDDO3
12
SCL
SCL
SCL
SCL
SCL
13
CLK2B
CLK2B
CLK2B
CLK2B
CLK2B
14
CLK2A
CLK2A
CLK2A
CLK2A
CLK2A
15
VDDO2
VDDO2
VDDO2
VDDO2
VDDO2
16
VDDO1
VDDO1
VDDO1
VDDO1
VDDO1
Notes:
1. CLKIN/CLKINB on pins 1 and 2 are differential clock inputs or XTAL inputs.
2. CLKIN on pin 3 is a single-ended clock input.
3. FDBK on pin 4 is a single-ended feedback input.
4. FDBK/FDBKB on pins 5 and 6 are differential feedback inputs.
Rev. 1.5
37
Si5 338
Table 17. Pin Function by Part Number (Continued)
Pin #
Si5338A: 710 MHz Si5338D: 710 MHz Si5338G: 710 MHz Si5338K: 710 MHz Si5338N: 710 MHz
Si5338B: 350 MHz Si5338E: 350 MHz Si5338H: 350 MHz Si5338L: 350 MHz Si5338P: 350 MHz
Si5338C: 200 MHz Si5338F: 200 MHz Si5338J: 200 MHz Si5338M: 200 MHz Si5338Q: 200 MHz
17
CLK1B
CLK1B
CLK1B
CLK1B
CLK1B
18
CLK1A
CLK1A
CLK1A
CLK1A
CLK1A
19
SDA
SDA
SDA
SDA
SDA
20
VDDO0
VDDO0
VDDO0
VDDO0
VDDO0
21
CLK0B
CLK0B
CLK0B
CLK0B
CLK0B
22
CLK0A
CLK0A
CLK0A
CLK0A
CLK0A
23
GND
GND
GND
GND
GND
24
VDD
VDD
VDD
VDD
VDD
Notes:
1. CLKIN/CLKINB on pins 1 and 2 are differential clock inputs or XTAL inputs.
2. CLKIN on pin 3 is a single-ended clock input.
3. FDBK on pin 4 is a single-ended feedback input.
4. FDBK/FDBKB on pins 5 and 6 are differential feedback inputs.
38
Rev. 1.5
Si5338
9. Package Outline: 24-Lead QFN
Figure 25. 24-Lead Quad Flat No-lead (QFN)
Table 18. Package Dimensions
Dimension
Min
Nom
Max
A
0.80
0.85
0.90
A1
0.00
0.02
0.05
b
0.18
0.25
0.30
D
D2
Notes:
1.
2.
3.
4.
4.00 BSC.
2.35
2.50
e
0.50 BSC.
E
4.00 BSC.
2.65
E2
2.35
2.50
2.65
L
0.30
0.40
0.50
aaa
0.10
bbb
0.10
ccc
0.08
ddd
0.10
eee
0.05
All dimensions shown are in millimeters (mm) unless otherwise noted.
Dimensioning and Tolerancing per ANSI Y14.5M-1994.
This drawing conforms to the JEDEC Outline MO-220, variation VGGD-8.
Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body
Components.
Rev. 1.5
39
Si5 338
10. Recommended PCB Land Pattern
Table 19. PCB Land Pattern
Dimension
Min
Nom
Max
P1
2.50
2.55
2.60
P2
2.50
2.55
2.60
X1
0.20
0.25
0.30
Y1
0.75
0.80
0.85
C1
3.90
C2
3.90
E
0.50
Notes:
General
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994 specification.
3. This Land Pattern Design is based on the IPC-7351 guidelines.
4. Connect the center ground pad to a ground plane with no less than five vias. These 5 vias should have a length of no
more than 20 mils to the ground plane. Via drill size should be no smaller than 10 mils. A longer distance to the ground
plane is allowed if more vias are used to keep the inductance from increasing.
Solder Mask Design
5. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is
to be 60 μm minimum, all the way around the pad.
Stencil Design
6. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder
paste release.
7. The stencil thickness should be 0.125 mm (5 mils).
8. The ratio of stencil aperture to land pad size should be 1:1 for all perimeter pins.
9. A 2x2 array of 1.0 mm square openings on 1.25 mm pitch should be used for the center ground pad.
Card Assembly
10. A No-Clean, Type-3 solder paste is recommended.
11. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components.
40
Rev. 1.5
Si5338
11. Top Marking
11.1. Si5338 Top Marking
11.2. Top Marking Explanation
Table 20. Top Marking Explanation
Line
Characters
Description
Line 1
Si5338
Base part number.
Line 2
Xxxxxx
X = Frequency and configuration code.
xxxxx = Optional NVM code for custom factory-programmed devices
(characters are not included for blank devices).
See "12. Ordering Information" on page 42.
Line 3
RTTTTT
R = Product revision.
TTTTT = Manufacturing trace code.
Circle with 0.5 mm diameter;
Pin 1 indicator.
left-justified
Line 4
YYWW
YY = Year.
WW = Work week.
Characters correspond to the year and work week of package assembly.
Rev. 1.5
41
Si5 338
12. Ordering Information
42
Rev. 1.5
Si5338
13. Device Errata
Please visit www.silabs.com to access the device errata document.
Rev. 1.5
43
Si5 338
DOCUMENT CHANGE LIST

Revision 0.2 to 0.3






Changed minimum output clock frequency from
5 MHz to 1 MHz.
Updated slew rates.
Updated " Features" on page 1.
Updated Table 6, “Input and Output Clock
Characteristics,” on page 8.
Deleted Table 12, “Output Driver Slew Rate Control”.
Revision 0.3 to 0.5













Major editorial changes to all sections to improve
clarity
Completed electrical specification tables with final
characterization results
Revised the maximum input and output frequencies
from 700 MHz to 710 MHz
Improved jitter specifications to reflect updated
characterization results
Added new Si5338N/P/Q ordering codes
Added typical application diagrams
Added an application section to highlight the
flexibility of the Si5338 in various timing functions
Added a configuration section to clarify configuration
options






44
Revision 0.6 to 0.65
Editorial changes to section 3.5 “Configuring the
Si5338” to improve clarity on ordering custom
Si5338 and on configuring “blank” Si5338.
Added pin numbers to device package drawings.
Updated ordering information to include evaluation
boards.
Updated first page description and applications
Added JC to specification tables.
Added GbE RM jitter specification with 1.875–
20 MHz integration band.
Updated Figure 9, “I2C Programming Procedure,” on
page 23 for consistency with register description.
Revision 0.65 to 1.0











Expanded PCI jitter specifications in Table 12.
Moved “Si5338 Registers” section to AN411.
Added I2C data rate specifications to Table 15.
Revised CMOS output currents down for each
CMOS driver that is active in Table 3.
Clarified CMOS output loads in Table 3
Added peak reflow temperature and footnote in
Table 2.
Added sticky and mask register info in "3.6. Status
Indicators" on page 24.
Added more information to Table note about CMOS
outputs and jitter in Table 12.
Changed all reference of MultiSynth Mn to MSn
Added "11. Top Marking" on page 41.
Reworded 3.5.2 and 3.5.3 for clarity.
Revision 1.0 to 1.1


Replaced all references to AN411 with "Si5338
Reference Manual" (AN411 has been replaced by
the Si5338 Reference Manual).
Clarified crystal specifications in Tables 8, 9, 10, 11
and added references to AN360.
Revision 1.1 to 1.2
Revision 0.55 to 0.6



Revision 0.5 to 0.55


Updated Figure 9 to include the entire programming
procedure.
Added "3.2.1. Loss-of-Signal (LOS) Alarm
Detectors" on page 19 to show the location of the
LOS detector circuits.
Updated input circuit diagrams in "3.2. Input Stage"
on page 19.
Update block diagrams with new input circuit
diagrams.

Updated Table 2 on page 4.
Added
Changed output duty cycle to 45–55%.
All I2C address now in binary.
Changed ordering information to reflect 710 MHz
limit.
Info on POR and soft reset added.
Updated Figure 15 on page 28.
Added register section.
Update programming procedure in “3.5. Configuring
the Si5338” to improve robustness.

CML current consumption specification.
Updated Table 6 on page 8.
Corrected
tR/tF for output clocks (single-ended) from
1.7 ns (max ) to 2.0 ns (max).
Added CML Output Voltage parameter.

Rev. 1.5
Updated Table 12 on page 13.
Updated
typical specifications for total jitter for PCI
Express 1.1 Common clocked topology.
Updated typical specifications for RMS jitter for PCI
Express 2.1 Common clocked topology.
Removed RMS jitter specification for PCI Express 2.1
Si5338
and 3.0 Data clocked topology.

Added Table 13, “Jitter Specifications, Clock Buffer
Mode (PLL Bypass)*,” on page 14.
Updated
typical additive jitter (12 kHz–20 MHz) from
0.150 to 0.165 ps RMS.



Updated Figure 9 on page 23 to provide workaround for spread spectrum errata.
Removed "3.5.4. Modifying a MultiSynth Output
Divider Ratio/Frequency Configuration". A soft reset
is now recommended after any changes to the
feedback or output dividers.
Added " " on page 42.
Revision 1.2 to 1.3




Removed down spread spectrum errata that has
been corrected in revision B.
Updated ordering information to refer to revision B
silicon.
Updated top marking explanation in Table 20.
Added further explanation to describe revisionspecific behavior of center spread spectrum in
section 3.10.7.
Revision 1.3 to 1.4

Added link to errata document.
Revision 1.4 to 1.5

Added setup and hold time specifications for I2C in
Table 15.
Rev. 1.5
45
Si5 338
CONTACT INFORMATION
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
Tel: 1+(512) 416-8500
Fax: 1+(512) 416-9669
Toll Free: 1+(877) 444-3032
Please visit the Silicon Labs Technical Support web page:
https://www.silabs.com/support/pages/contacttechnicalsupport.aspx
and register to submit a technical support request.
Patent Notice
Silicon Labs invests in research and development to help our customers differentiate in the market with innovative low-power, small size, analogintensive mixed-signal solutions. Silicon Labs' extensive patent portfolio is a testament to our unique approach and world-class engineering team
The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice.
Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from
the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features
or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to
support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages.
Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc.
Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders.
46
Rev. 1.5