SAP51 / SAP5S AS-Interface Spec. V3.0 Compliant Universal AS-i IC Brief Description Benefits The SAP5S/SAP51 is a next-generation CMOS integrated circuit for AS-Interface networks. This lowlevel field bus AS-i (Actuator Sensor Interface) was designed for easy, safe, and cost-effective interconnection of sensors, actuators, and switches. It transports both power and data over the same twowire unshielded cable. Cost savings due to integrated Safety Code Generator (SAP5S only) Special burst protection circuitry Excellent electromagnetic compatibility The SAP5S/SAP51 is used as part of a master or slave node and functions as an interface to the physical bus. It provides the power supply, physical data transfer, and communication protocol handling. The SAP5S/SAP51 is fully compliant with the AS-Interface Complete Specification V3.0. It is function and pin compatible with the SAP4.1 (AS2702). The SAP5S/SAP51 can be programmed by the user to operate in Standard Slave Mode, Safety Mode (SAP5S only), or Master Mode. The special AS-i Safety Mode (SAP5S only) assures short response times regarding security-related events. All configuration data are stored in an internal EEPROM that can be easily programmed by a stationary or handheld programming device. The SAP5S/SAP51 is optimized for harsh environments by its special burst protection circuitry and excellent electromagnetic compatibility. Physical Characteristics Operational temperature range: -25 to +85°C SOP16 and SOP20 package Available Support ZMDI AS-Interface Programmer Kit USB ZMDI SAP5 Evaluation Board V2.0 Related Products ASI4U Universal AS-Interface IC SAP5S/SAP51 Basic Application Circuits Standard Application UOUT +24V PFAULT OSC1 DSTBn PSTBn OSC2 LTGP ASI+ D[3:0] Features Compliant with the AS-Interface Complete Specification V3.0 Universal application: slaves, masters, repeaters Integrated safety code generator (SAP5S only) On-chip electronic inductor: 55mA current drive capability Two LED outputs to support all AS-Interface Complete Specification V3.0 status indication modes P[3:0] CDC LTPN ASI- User programmable to operation in Standard Slave Mode, Safety Mode, or Master Mode Supports 5.33 and 16 MHz crystals by automatic frequency detection Data pre-processing functions Clock and communication watchdogs for high system security U5R SAP51/ SAP5S LED1 LED2 +0V Safety Mode Slave Application UOUT U5R OSC1 OSC2 ASI+ D2 LTGP D3 ASI- LTPN SAP5S CDC D0 D1 For more information, contact ZMDI via [email protected]. © 2015 Zentrum Mikroelektronik Dresden AG — Rev. 3.20 — June 17, 2015 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. SAP51 / SAP5S AS-Interface Spec. V3.0 Compliant Universal AS-i IC SAP5S / SAP51 Block Diagram U5R CDC Power Supply Thermal Protection Electronic Inductor UOUT Power Fail Detector LTGP LTGN Param APF Offset Data pos Receiver Main State Machine neg Offset UART Typical Applications Transmitter AS-i Master Modules (SAP5S only) I/O D[3:0] LED Output DSTB I/O DSTBn PSTB Output PSTBn PFAULT Input PFAULT LED1, LED2 clk AS-i Safety Modules P[3:0] clk AS-i Slave Modules MAN I/O OSC1 OSC2 Oscillator PLL EEPROM clk Ordering Information Ordering Code SAP5SD-A-G1-T Operating Temperature Package Type RoHS? Packaging -25°C to +85°C SOP20 / 300 mil Yes Tubes (37 parts/tube) -25°C to +85°C SOP20 / 300 mil Yes Tape and Reel (1000 parts/reel) -25°C to +85°C SOP16 / 300 mil Yes Tubes (46 parts/tube) -25°C to +85°C SOP16 / 300 mil Yes Tape and Reel (1000 parts/reel) SAP51D-A-G1-T SAP5SD-A-G1-R SAP51D-A-G1-R SAP5SD-B-G1-T SAP51D-B-G1-T SAP5SD-B-G1-R SAP51D-B-G1-R Sales and Further Information www.zmdi.com [email protected] Zentrum Mikroelektronik Dresden AG Global Headquarters Grenzstrasse 28 01109 Dresden, Germany ZMD America, Inc. 1525 McCarthy Blvd., #212 Milpitas, CA 95035-7453 USA Central Office: Phone +49.351.8822.306 Fax +49.351.8822.337 USA Phone 1.855.275.9634 Phone +1.408.883.6310 Fax +1.408.883.6358 European Technical Support Phone +49.351.8822.7.772 Fax +49.351.8822.87.772 DISCLAIMER: This information applies to a product under development. Its characteristics and specifications are subject to change without notice. Zentrum Mikroelektronik Dresden AG (ZMD AG) assumes no obligation regarding future manufacture unless otherwise agreed to in writing. The information furnished hereby is believed to be true and accurate. However, under no circumstances shall ZMD AG be liable to any customer, licensee, or any other third party for any special, indirect, incidental, or consequential damages of any kind or nature whatsoever arising out of or in any way related to the furnishing, performance, or use of this technical data. ZMD AG hereby expressly disclaims any liability of ZMD AG to any customer, licensee or any other third party, and any such customer, licensee and any other third party hereby waives any liability of ZMD AG for any damages in connection with or arising out of the furnishing, performance or use of this technical data, whether based on contract, warranty, tort (including negligence), strict liability, or otherwise. European Sales (Stuttgart) Phone +49.711.674517.55 Fax +49.711.674517.87955 Zentrum Mikroelektronik Dresden AG, Japan Office 2nd Floor, Shinbashi Tokyu Bldg. 4-21-3, Shinbashi, Minato-ku Tokyo, 105-0004 Japan ZMD FAR EAST, Ltd. 3F, No. 51, Sec. 2, Keelung Road 11052 Taipei Taiwan Phone +81.3.6895.7410 Fax +81.3.6895.7301 Phone +886.2.2377.8189 Fax +886.2.2377.8199 Zentrum Mikroelektronik Dresden AG, Korea Office U-space 1 Building Unit B, 906-1 660, Daewangpangyo-ro Bundang-gu, Seongnam-si Gyeonggi-do, 463-400 Korea Phone +82.31.950.7679 Fax +82.504.841.3026 © 2015 Zentrum Mikroelektronik Dresden AG — Rev. 3.20 — June 17, 2015 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner.