ZSC31150 Fast Automotive Sensor Signal Conditioner Brief Description Benefits The ZSC31150 is a CMOS integrated circuit for highly accurate amplification and sensor-specific correction of bridge sensor signals. Digital compensation of sensor offset, sensitivity, temperature drift, and non-linearity is accomplished via an internal 16-bit RISC microcontroller running a correction algorithm, with calibration coefficients stored in an EEPROM. The ZSC31150 is adjustable to nearly all bridge sensor types. Measured values are provided at the analog voltage output or at the digital ZACwire™ and I²C™* interface. The digital interface can be used for a simple PC-controlled calibration procedure in order to program a set of calibration coefficients into an on-chip EEPROM. A specific sensor and a ZSC31150 can be mated digitally: fast, precise, and without the cost overhead associated with trimming by external devices or a laser. No external trimming components required Only a few external protection devices needed PC-controlled configuration and single pass calibration via I²C™ or ZACwire™ interface: simple, cost efficient, quick, and precise End-of-line calibration via I²C™ or ZACwire™ interface High accuracy (0.25% FSO @ -25 to 85°C; 0.5% FSO @ -40 to 125°C) Excellent EMC/ESD robustness and AEC-Q100 qualification Available Support Evaluation Kits Application Notes Mass Calibration System Features Physical Characteristics Supply voltage: 4.5 to 5.5 V Operation temperature: -40°C to 125°C (-40°C to +150°C extended temperature range) Available as DFN14 (5mm x 4mm; wettable flanks), SSOP14, and die ZSC31150 Application Circuit Out / OWI GND C2 100nF 8 VSSE VDDE 7 9 AOUT VDD 6 +4.5V to +5.5V C3 47nF Sensor Bridge 10 VBN 11 VBR_B 12 VBP C4 C5 ZSC31150 Digital compensation of sensor offset, sensitivity, temperature drift, and non-linearity Adjustable to nearly all bridge sensor types Analog gain of up to 420 Output options: ratiometric analog voltage output (5% to 95% maximum, 12.4-bit resolution) or ZACwire™ (digital one-wire-interface) Temperature compensation: internal or external diode, bridge resistance, thermistor Sensor biasing by voltage or constant current Sample rate: up to 7.8kHz High voltage protection up to 33V Supply current: max. 5.5mA Reverse polarity and short-circuit protection Wide operation temperature depending on part number: up to -40 to +150°C Traceability by user-defined EEPROM entries Safety and diagnostic functions VSUPP n.c. 5 SCL 4 SCL SDA 3 SDA Serial Interface 13 VBR_T VSSA 2 14 IRTEMP VDDA 1 C1 100nF Temperature Sensor * I²C™ is a trademark of NXP. For more information, contact ZMDI via [email protected]. © 2015 Zentrum Mikroelektronik Dresden AG — Rev. 2.41— July 27, 2015 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. ZSC31150 Fast Automotive Sensor Signal Conditioner ZSC31150 Block Diagram PGA MUX RAM ADC TS Analog Block ZACwire™ I2C™ EEPROM CMC DAC ROM Digital Data I/O Analog Out BAMP ZSC31150 Digital Block Ordering Information Sales Code Description Package ZSC31150GE ZSC31150 Die — Temperature range: -40°C to +150°C Unsawn on Wafer: add “B” to sales code Sawn on Wafer Frame: add “C” Waffle Pack: add “D” ZSC31150GEG2-R ZSC31150 DFN14 (5mmx4mm; wettable flanks) —Temperature range: -40°C to 150°C Tape & Reel ZSC31150GAG2-R ZSC31150 DFN14 (5mmx4mm; wettable flanks) —Temperature range: -40°C to 125°C Tape & Reel ZSC31150GEG1 ZSC31150 SSOP14—Temperature range: -40°C to +150°C ZSC31150GLG1 ZSC31150 SSOP14—Temperature range: -40°C to +150°C (Long life: 5000h @150°C) Tube: add “-T” to sales code Tape & Reel: add “-R” ZSC31150GAG1 ZSC31150 SSOP14—Temperature range: -40°C to +125°C ZSC31150KIT Evaluation Kit V1.2 ZSC31150 SSC Evaluation Kit: three interconnecting boards, five ZSC31150 SSOP14 samples, USB cable (software can be downloaded from product page at www.zmdi.com/zsc31150) ZSC31150 Mass Calibration System V1.1 Modular Mass Calibration System (MSC) for ZSC31150: MCS boards, cable, connectors (software can be downloaded from product page) Sales and Further Information www.zmdi.com [email protected] Zentrum Mikroelektronik Dresden AG Global Headquarters Grenzstrasse 28 01109 Dresden, Germany ZMD America, Inc. 1525 McCarthy Blvd., #212 Milpitas, CA 95035-7453 USA Central Office: Phone +49.351.8822.306 Fax +49.351.8822.337 USA Phone 1.855.275.9634 Phone +1.408.883.6310 Fax +1.408.883.6358 European Technical Support Phone +49.351.8822.7.772 Fax +49.351.8822.87.772 DISCLAIMER: This information applies to a product under development. Its characteristics and specifications are subject to change without notice. Zentrum Mikroelektronik Dresden AG (ZMD AG) assumes no obligation regarding future manufacture unless otherwise agreed to in writing. The information furnished hereby is believed to be true and accurate. However, under no circumstances shall ZMD AG be liable to any customer, licensee, or any other third party for any special, indirect, incidental, or consequential damages of any kind or nature whatsoever arising out of or in any way related to the furnishing, performance, or use of this technical data. ZMD AG hereby expressly disclaims any liability of ZMD AG to any customer, licensee or any other third party, and any such customer, licensee and any other third party hereby waives any liability of ZMD AG for any damages in connection with or arising out of the furnishing, performance or use of this technical data, whether based on contract, warranty, tort (including negligence), strict liability, or otherwise. European Sales (Stuttgart) Phone +49.711.674517.55 Fax +49.711.674517.87955 Zentrum Mikroelektronik Dresden AG, Japan Office 2nd Floor, Shinbashi Tokyu Bldg. 4-21-3, Shinbashi, Minato-ku Tokyo, 105-0004 Japan ZMD FAR EAST, Ltd. 3F, No. 51, Sec. 2, Keelung Road 11052 Taipei Taiwan Phone +81.3.6895.7410 Fax +81.3.6895.7301 Phone +886.2.2377.8189 Fax +886.2.2377.8199 Zentrum Mikroelektronik Dresden AG, Korea Office U-space 1 Building Unit B, 906-1 660, Daewangpangyo-ro Bundang-gu, Seongnam-si Gyeonggi-do, 463-400 Korea Phone +82.31.950.7679 Fax +82.504.841.3026 © 2015 Zentrum Mikroelektronik Dresden AG — Rev. 2.41— July 27, 2015 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner.