ZSSC3015 RBicdLite-Auto™ Sensor Signal Conditioner with Diagnostics Brief Description Benefits The ZSSC3015 sensor signal conditioner IC is adjustable to nearly all piezo-resistive bridge sensors. Measured and corrected bridge values are provided at the Sig™ pin, which can be configured as an analog voltage output or as a one-wire serial digital output. No external trimming components required PC-controlled configuration and calibration via ZACwire™ one-wire interface – simple, low cost High accuracy (as high as ±0.1% FSO @ -25 to 85°C; ±0.25% FSO @ -50 to 150°C) Single-pass calibration – quick and precise The ZACwire™ digital one-wire interface (OWI) can be used for a simple PC-controlled calibration procedure to program a set of calibration coefficients into an on-chip EEPROM. The calibrated ZSSC3015 and a specific sensor are mated digitally: fast, precise, and without the cost overhead associated with trimming by external devices or laser. Integrated diagnostics functions make the ZSSC3015 particularly well suited for automotive applications. Features Digital compensation of sensor offset, sensitivity, temperature drift, and nonlinearity Programmable analog gain and digital gain; accommodates bridges with spans < 1mV/V and high offset Many diagnostic features on chip (e.g., EEPROM signature, bridge connection checks, bridge short detection, power loss detection) Independently programmable high and low clipping levels 24-bit customer ID field for module traceability Internal temperature compensation reference (no external components) Option for external temperature compensation with addition of single diode Output options: rail-to-rail ratiometric analog voltage (12-bit resolution), absolute analog voltage, ZACwire™ digital one-wire interface Fast power-up to data out response; output available 5ms after power-up Current consumption depends on programmed sample rate and mode: 1mA down to 300µA (typ.) Fast response time: 1.4ms typical High voltage protection: ≤ 30V with external JFET AEC-Q100 qualified Available Support Evaluation Kit available Mass Calibration System available Support for industrial mass calibration available Quick circuit customization possible for large production volumes Physical Characteristics Wide operation temperature: –50°C to +150°C Supply voltage 2.7 to 5.5V; with external JFET, 5.5 to 30V Small SOP8 package ZSSC3015 Application Circuit Vsupply +2.7 to +5.5 V VDD Sig™ OUT/OWI ZSSC3015 VBP Vgate VBN VSS 0.1 F Ground For more information, contact ZMDI via [email protected]. © 2014 Zentrum Mikroelektronik Dresden AG — Rev. 1.12 —December 26, 2014. All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. ZSSC3015 RBicdLite-Auto™ Sensor Signal Conditioner with Diagnostics JFET1 (Optional if supply is 2.7 to 5.5 V) ZSSC3015 Block Diagram S 0.1 F Highly Versatile Applications in Many Markets Including VDD (2.7 to 5.5 V) Industrial Building Automation Vgate RBicdLite-Auto PTAT Sensor Diagnostics Temperature Reference Voltage Reference VBP Optional Ext. Diode for Temp White Goods INMUX PREAMP Power Save EEPROM with Charge Pump ExtTemp (Optional) Bsink Automotive POR/Oscillator Portable Devices Your Innovative Designs 12-Bit DAC ZSSC3015 A VBN Office Automation 5.5 V to 30 V VSUPPLY D _ D 14-Bit ADC Digital Core SigTM + ZACwireTM Interface Power Lost Diagnostic Analog Block VSS Digital Block Rail-to-Rail Ratiometric Voltage Output Applications Absolute Analog Voltage Output Applications BSS169 Vsupply S +2.7 to +5.5 V 1 Bsink 2 VBP 3 ExtTemp 4 VBN VSS 8 TM Sig OUT 7 VDD 6 1 Bsink VSS 8 2 VBP SigTM 7 3 ExtTemp Vgate 5 ZSSC3015 Optional Bsink 0 V to 1 V Ratiometric Rail-to-Rail OWI/ZACwireTM OUTBUF1 4 VBN 0.1 F Optional Bsink D Vsupply +5.5 to +30 V OUT VDD 6 Vgate 5 0.1 F ZSSC3015 Ground Ground Part Ordering Examples (See section 11 in the data sheet for additional options.) Sales Code Description Package ZSSC3015NE1B ZSSC3015 Die — Temperature range: -50°C to +150°C Unsawn on Wafer ZSSC3015NE1C ZSSC3015 Die — Temperature range: -50°C to +150°C Sawn on Wafer Frame ZSSC3015NE2T(R) ZSSC3015 SOP8 (150 mil) — Temperature range: -50°C to +150°C Tube: add “-T” to sales code. Reel: add “-R” ZSSC3015KIT Kit ZSSC3015 SSC Evaluation Kit: Communication Board, SSC Board, Sensor Replacement Board, USB cable, 5 IC samples, instructions for downloading SSC Evaluation Software Sales and Further Information www.zmdi.com [email protected] Zentrum Mikroelektronik Dresden AG Global Headquarters Grenzstrasse 28 01109 Dresden, Germany ZMD America, Inc. 1525 McCarthy Blvd., #212 Milpitas, CA 95035-7453 USA Central Office: Phone +49.351.8822.306 Fax +49.351.8822.337 USA Phone 1.855.275.9634 Phone +1.408.883.6310 Fax +1.408.883.6358 European Technical Support Phone +49.351.8822.7.772 Fax +49.351.8822.87.772 DISCLAIMER: This information applies to a product under development. Its characteristics and specifications are subject to change without notice. Zentrum Mikroelektronik Dresden AG (ZMD AG) assumes no obligation regarding future manufacture unless otherwise agreed to in writing. The information furnished hereby is believed to be true and accurate. However, under no circumstances shall ZMD AG be liable to any customer, licensee, or any other third party for any special, indirect, incidental, or consequential damages of any kind or nature whatsoever arising out of or in any way related to the furnishing, performance, or use of this technical data. ZMD AG hereby expressly disclaims any liability of ZMD AG to any customer, licensee or any other third party, and any such customer, licensee and any other third party hereby waives any liability of ZMD AG for any damages in connection with or arising out of the furnishing, performance or use of this technical data, whether based on contract, warranty, tort (including negligence), strict liability, or otherwise. European Sales (Stuttgart) Phone +49.711.674517.55 Fax +49.711.674517.87955 Zentrum Mikroelektronik Dresden AG, Japan Office 2nd Floor, Shinbashi Tokyu Bldg. 4-21-3, Shinbashi, Minato-ku Tokyo, 105-0004 Japan ZMD FAR EAST, Ltd. 3F, No. 51, Sec. 2, Keelung Road 11052 Taipei Taiwan Phone +81.3.6895.7410 Fax +81.3.6895.7301 Phone +886.2.2377.8189 Fax +886.2.2377.8199 Zentrum Mikroelektronik Dresden AG, Korea Office U-space 1 Building Unit B, 906-1 660, Daewangpangyo-ro Bundang-gu, Seongnam-si Gyeonggi-do, 463-400 Korea Phone +82.31.950.7679 Fax +82.504.841.3026 © 2014 Zentrum Mikroelektronik Dresden AG — Rev. 1.12 —December 26, 2014. All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner.