Data Sheet Rev. 2.10 / October 2013 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner with Diagnostic Features Multi-Market Sensing Platforms Precise and Deliberate ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Brief Description Benefits The ZSC31015 is adjustable to nearly all piezoresistive bridge sensors. Measured and corrected bridge values are provided at the SIG™ pin, which can be configured as an analog voltage output or as a one-wire serial digital output. No external trimming components required Simple PC-controlled configuration and calibration via one-wire interface High accuracy: ±0.1% FSO @ -25 to 85°C; ±0.25% FSO @ -50 to 150°C The digital one-wire interface (OWI) can be used for a simple PC-controlled calibration procedure to program a set of calibration coefficients into an on-chip EEPROM. The calibrated ZSC31015 and a specific sensor are mated digitally: fast, precise, and without the cost overhead associated with trimming by external devices or laser. Integrated diagnostics functions make the ZSC31015 particularly well suited for automotive applications.* Single-pass calibration – quick and precise Available Support Evaluation Kit available Mass Calibration System available Support for industrial mass calibration available Quick circuit customization possible for large production volumes Features Digital compensation of sensor offset, sensitivity, temperature drift, and non-linearity Programmable analog gain and digital gain; accommodates bridges with spans < 1mV/V and high offset Many diagnostic features on chip (e.g., EEPROM signature, bridge connection checks, bridge short detection, power loss detection) Independently programmable high and low clipping levels 24-bit customer ID field for module traceability Internal temperature compensation reference (no external components) Option for external temperature compensation with addition of single diode Output options: rail-to-rail ratiometric analog voltage (12-bit resolution), absolute analog voltage, digital one-wire interface Fast power-up to data out response; output available 5ms after power-up Current consumption depends on programmed sample rate: 1mA down to 250A (typical) Fast response time: 1ms (typical) High voltage protection up to 30V with external JFET Physical Characteristics Wide operation temperature: –50°C to +150°C Supply voltage 2.7 to 5.5V; with external JFET, 5.5 to 30V Small SOP8 package ZSC31015 Application Circuit Vsupply +2.7 to +5.5 V VDD SIG™ OUT/OWI ZSC31015 VBP Vgate VBN VSS 0.1 F Ground * Not AEC-Q100-qualified. For more information, contact ZMDI via [email protected]. © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10— October 9, 2013. All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features ZSC31015 Block Diagram JFET1 (Optional if supply is 2.7 to 5.5 V) S 0.1 F Highly Versatile Applications in Many Markets Including VDD (2.7 to 5.5 V) Industrial Building Automation Office Automation White Goods Automotive * Portable Devices Your Innovative Designs Vgate RBicdLite PTAT Sensor Diagnostics Temperature Reference VDD Regulator VBP INMUX PREAMP Power Save EEPROM with Charge Pump Ext Temp (Optional) Bsink POR/Oscillator 12-Bit DAC ZSC31015 A VBN Optional Ext. Diode for Temp 5.5 V to 30 V VSUPPLY D _ D 14-Bit ADC Digital Core SIGTM + 0 V to 1 V Ratiometric Rail-to-Rail OWI/ZACwireTM OUTBUF1 ZACwireTM Interface Power Lost Diagnostic Analog Block Digital Block VSS * Not AEC-Q100-qualified. Rail-to-Rail Ratiometric Voltage Output Applications Absolute Analog Voltage Output Applications BSS169 Vsupply S +2.7 to +5.5 V 1 Bsink 2 VBP 3 ExtTemp 4 VBN Optional Bsink VSS 8 TM Sig OUT 7 VSS 8 2 VBP SigTM 7 3 ExtTemp VDD 6 Vgate 5 ZSC31015 1 Bsink 4 VBN 0.1 F Optional Bsink D Vsupply +5.5 to +30 V OUT VDD 6 Vgate 5 0.1 F ZSC31015 Ground Ground Ordering Examples (See section 11 of the data sheet for additional temperature range options.) Sales Code Description Package ZSC31015EEB ZSC31015 Die — Temperature range: -50°C to +150°C Unsawn on Wafer ZSC31015EEC ZSC31015 Die — Temperature range: -50°C to +150°C Sawn on Wafer Frame ZSC31015EEG1 ZSC31015 SOP8 (150 mil) — Temperature range: -50°C to +150°C Tube: add “-T” to sales code. Reel: add “-R” ZSC31015KIT ZSC31015 ZACwire™ SSC Evaluation Kit: Communication Board, SSC Board, Sensor Replacement Board, Evaluation Software, USB Cable, 5 IC Samples (SOP8 150mil) Kit Sales and Further Information www.zmdi.com [email protected] Zentrum Mikroelektronik Dresden AG Global Headquarters Grenzstrasse 28 01109 Dresden, Germany ZMD America, Inc. 1525 McCarthy Blvd., #212 Milpitas, CA 95035-7453 USA Central Office: Phone +49.351.8822.0 Fax +49.351.8822.600 USA Phone +855.275.9634 Phone +408.883.6310 Fax +408.883.6358 European Technical Support Phone +49.351.8822.7.772 Fax +49.351.8822.87.772 DISCLAIMER: This information applies to a product under development. Its characteristics and specifications are subject to change without notice. Zentrum Mikroelektronik Dresden AG (ZMD AG) assumes no obligation regarding future manufacture unless otherwise agreed to in writing. The information furnished hereby is believed to be true and accurate. However, under no circumstances shall ZMD AG be liable to any customer, licensee, or any other third party for any special, indirect, incidental, or consequential damages of any kind or nature whatsoever arising out of or in any way related to the furnishing, performance, or use of this technical data. ZMD AG hereby expressly disclaims any liability of ZMD AG to any customer, licensee or any other third party, and any such customer, licensee and any other third party hereby waives any liability of ZMD AG for any damages in connection with or arising out of the furnishing, performance or use of this technical data, whether based on contract, warranty, tort (including negligence), strict liability, or otherwise. European Sales (Stuttgart) Phone +49.711.674517.55 Fax +49.711.674517.87955 Zentrum Mikroelektronik Dresden AG, Japan Office 2nd Floor, Shinbashi Tokyu Bldg. 4-21-3, Shinbashi, Minato-ku Tokyo, 105-0004 Japan ZMD FAR EAST, Ltd. 3F, No. 51, Sec. 2, Keelung Road 11052 Taipei Taiwan Phone +81.3.6895.7410 Fax +81.3.6895.7301 Phone +886.2.2377.8189 Fax +886.2.2377.8199 Zentrum Mikroelektronik Dresden AG, Korea Office U-space 1 Building 11th Floor, Unit JA-1102 670 Sampyeong-dong Bundang-gu, Seongnam-si Gyeonggi-do, 463-400 Korea Phone +82.31.950.7679 Fax +82.504.841.3026 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 — October 9, 2013 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Contents 1 Electrical Characteristics ................................................................................................................ 8 1.1. Absolute Maximum Ratings ...................................................................................................... 8 1.2. Recommended Operating Conditions ....................................................................................... 8 1.3. Electrical Parameters ............................................................................................................... 9 1.3.1. Supply/Regulation Characteristics ...................................................................................... 9 1.3.2. Parameters for Analog Front-End (AFE) ............................................................................. 9 1.3.3. Parameters for EEPROM ................................................................................................... 9 1.3.4. Parameters for A/D Converter ............................................................................................ 9 1.3.5. Parameters for Analog Output (DAC and Buffer) ................................................................ 9 1.3.6. Diagnostics ........................................................................................................................10 1.3.7. External Temperature Measurement .................................................................................10 1.3.8. Parameters for ZACwire™ Serial Interface ........................................................................10 1.3.9. Parameters for System Response .....................................................................................10 1.4. Analog Inputs versus Output Resolution..................................................................................11 2 Circuit Description .........................................................................................................................14 2.1. Signal Flow and Block Diagram ...............................................................................................14 2.2. Analog Front End ....................................................................................................................15 2.2.1. Bandgap/PTAT and PTAT Amplifier ..................................................................................15 2.2.2. Bridge Supply ....................................................................................................................15 2.2.3. PREAMP Block .................................................................................................................15 2.2.4. Analog-to-Digital Converter (ADC) .....................................................................................16 2.3. Digital Signal Processor ..........................................................................................................16 2.3.1. EEPROM ...........................................................................................................................18 2.3.2. One-Wire Interface – ZACwire™ .......................................................................................18 2.4. Output Stage ...........................................................................................................................18 2.4.1. Digital to Analog Converter (Output DAC) with Programmable Clipping Limits ..................18 2.4.2. Output Buffer .....................................................................................................................19 2.4.3. Voltage Reference Block ...................................................................................................19 2.5. Clock Generator / Power-On Reset (CLKPOR) .......................................................................21 2.5.1. Trimming the Oscillator ......................................................................................................21 2.6. Diagnostic Features ................................................................................................................21 2.6.1. EEPROM Integrity .............................................................................................................22 Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 4 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 2.6.2. Sensor Connection Check .................................................................................................22 2.6.3. Sensor Short Check ..........................................................................................................23 2.6.4. Power Loss Detection ........................................................................................................23 2.6.5. ExtTemp Connection Checks ............................................................................................23 3 Functional Description ...................................................................................................................24 3.1. General Working Mode ...........................................................................................................24 3.2. ZACwire™ Communication Interface.......................................................................................26 3.2.1. Properties and Parameters ................................................................................................26 3.2.2. Bit Encoding ......................................................................................................................26 3.2.3. Write Operation from Master to ZSC31015 ........................................................................27 3.2.4. ZSC31015 Read Operations .............................................................................................27 3.2.5. High Level Protocol ...........................................................................................................30 3.3. Command/Data Bytes Encoding..............................................................................................31 3.4. Calibration Sequence ..............................................................................................................32 3.5. EEPROM Bits ..........................................................................................................................34 3.6. Calibration Math ......................................................................................................................38 3.6.1. Correction Coefficients ......................................................................................................38 3.6.2. Interpretation of Binary Numbers for Correction Coefficients .............................................38 3.7. Reading EEPROM Contents ...................................................................................................42 4 Application Circuit Examples .........................................................................................................43 4.1. Three-Wire Rail-to-Rail Ratiometric Output .............................................................................43 4.2. Absolute Analog Voltage Output..............................................................................................44 4.3. Three-Wire Ratiometric Output with Over-Voltage Protection ..................................................45 4.4. Digital Output ..........................................................................................................................45 4.5. Output Resistor/Capacitor Limits .............................................................................................45 5 EEPROM Restoration ...................................................................................................................46 5.1. Default EEPROM Contents .....................................................................................................46 5.1.1. Osc_Trim ...........................................................................................................................46 5.1.2. 1V_Trim/JFET_Trim ..........................................................................................................46 5.2. EEPROM Restoration Procedure ............................................................................................46 6 Pin Configuration and Package .....................................................................................................48 7 ESD/Latch-Up-Protection ..............................................................................................................49 Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 5 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 8 Test ...............................................................................................................................................49 9 Quality and Reliability ....................................................................................................................49 10 Customization ...............................................................................................................................49 11 Part Ordering Codes .....................................................................................................................50 12 Related Documents .......................................................................................................................50 13 Definitions of Acronyms .................................................................................................................51 14 Document Revision History ...........................................................................................................52 List of Figures Figure 2.1 Figure 2.2 Figure 3.1 Figure 3.2 Figure 3.3 Figure 3.4 Figure 3.5 Figure 3.6 Figure 3.7 Figure 3.8 Figure 3.9 Figure 4.1 Figure 4.2 Figure 4.3 Figure 5.1 Figure 6.1 ZSC31015 Block Diagram ..................................................................................................................14 DAC Output Timing for Highest Update Rate .....................................................................................19 General Working Mode .......................................................................................................................25 Manchester Duty Cycle .......................................................................................................................26 19-Bit Write Frame ..............................................................................................................................27 Read Acknowledge .............................................................................................................................27 Digital Output (NOM) Bridge Readings ..............................................................................................28 Digital Output (NOM) Bridge Readings with Temperature .................................................................28 Read EEPROM Contents ...................................................................................................................29 Transmission of a Number of Data Packets .......................................................................................29 ZACwire™ Output Timing for Lower Update Rates............................................................................30 Rail-to-Rail Ratiometric Voltage Output – Temperature Compensation via External Diode ..............43 Absolute Analog Voltage Output – Temperature Compensation via Internal Temperature PTAT with External JFET Regulation ...................................................................................................................44 Ratiometric Output, Temperature Compensation via Internal Diode ..................................................45 EEPROM Validation and Restoration Procedure ...............................................................................47 ZSC31015 Pin-Out Diagram ...............................................................................................................48 List of Tables Table 1.1 Table 1.2 Table 1.3 Table 1.4 Table 2.1 Table 2.2 Table 2.3 Table 3.1 Table 3.2 Data Sheet October 9, 2013 ADC Resolution Characteristics for an Analog Gain of 6 ...................................................................11 ADC Resolution Characteristics for an Analog Gain of 24 .................................................................12 ADC Resolution Characteristics for an Analog Gain of 48 .................................................................12 ADC Resolution Characteristics for an Analog Gain of 96 .................................................................13 1V Reference Trim (1V vs. Trim for Nominal Process Run) ...............................................................20 Oscillator Trimming .............................................................................................................................21 Summary of Diagnostic Features .......................................................................................................22 Pin Configuration and Latch-Up Conditions .......................................................................................26 Special Measurement/Idle Time between Packets versus Update Rate ...........................................29 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 6 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Table 3.3 Table 3.4 Table 3.5 Table 3.6 Table 3.7 Table 3.8 Table 3.9 Table 3.10 Table 3.11 Table 6.1 Table 6.2 Data Sheet October 9, 2013 Total Transmission Time for Different Update Rate Settings and Output Configuration ....................30 Command/Data Bytes Encoding.........................................................................................................31 ZSC31015 EEPROM Bits ...................................................................................................................34 Correction Coefficients .......................................................................................................................38 Gain_B [13:0] Weightings ...................................................................................................................39 Offset_B Weightings ...........................................................................................................................39 Gain_T Weightings .............................................................................................................................40 Offset_T Weightings ...........................................................................................................................40 EEPROM Read Order ........................................................................................................................42 Storage and Soldering Conditions for SOP-8 Package ......................................................................48 ZSC31015 Pin Configuration ..............................................................................................................48 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 7 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 1 Electrical Characteristics 1.1. Absolute Maximum Ratings Note: The absolute maximum ratings are stress ratings only. The device might not function or be operable above the operating conditions given in section 1.2. Stresses exceeding the absolute maximum ratings might also damage the device. In addition, extended exposure to stresses above the recommended operating conditions might affect device reliability. ZMDI does not recommend designing to the “Absolute Maximum Ratings.” Parameter Symbol Min Max Unit VDD -0.3 6.0 V Analog Supply Voltage Voltages at Analog I/O – In Pin VINA -0.3 VDD+0.3 V Voltages at Analog I/O – Out Pin VOUTA -0.3 VDD+0.3 V Storage Temperature Range (10 hours) TSTOR -50 150 °C Storage Temperature Range (<10 hours) TSTOR <10h -50 170 °C Note: Also see Table 6.1 regarding soldering temperature and storage conditions. 1.2. Recommended Operating Conditions Parameter Analog Supply Voltage to Ground Analog Supply Voltage (with external JFET Regulator) Common Mode Voltage Ambient Temperature Range 1), 2) External Capacitance between VDD and Ground Output Load Resistance to VDD 3) Output Load Resistance to VSS Output Load Capacitance Bridge Resistance 6) Power-On Rise Time 1) 2) 3) 4) 5) 6) 5) 3),4) Symbol Min Typ Max Unit VDD 2.7 5.0 5.5 V VSUPP 5.5 7 30 V VCM 1 VDD – 1.3 V TAMB -50 150 C CVDD 100 470 nF RL,OUT 5 RL,OUT 5 CL,OUT 1 RBR 0.2 tPON 220 k k 10 15 nF 100 k 100 ms Note that the maximum EEPROM programming temperature is 85°C. If buying die, designers should use caution not to exceed maximum junction temperature by proper package selection. Only needed for Analog Output Mode; not needed for Digital Output Mode. When a pull-down resistor is used as the load resistor, the power loss detection diagnostic for loss of VSS cannot be assured at RL=5k; RL=10k is recommended for this configuration. Note: for unlocked devices or during calibration, the minimum value of output load resistance to VSS is 20kΩ. Using the output for digital calibration, CL,OUT is limited by the maximum rise time tZAC,rise. See section 1.3.8. Note: Minimum bridge resistance is only a factor if using the Bsink feature. The rds(on) of the Bsink transistor is 8 to 10Ω when operating at VDD=5V. This does give rise to a ratiometricity inaccuracy that becomes greater with low bridge resistances. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 8 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 1.3. Electrical Parameters See important table notes at the end of the table. Note: For parameters marked with an asterisk, there is no verification in mass production; the parameter is guaranteed by design and/or quality observation. Parameter 1.3.1. Symbol Conditions Min Typ Max Unit 2.7 5.0 5.5 V Supply/Regulation Characteristics Supply Voltage VDD Supply Current (varies with update rate and output mode) IDD At minimum update rate 0.25 At maximum update rate 1.0 1.4 20 100 Temperature Coefficient – PTAT Source * TCPTAT Power Supply Rejection Ratio * PSRR 60 Power-On Reset Level POR 1.4 1.3.2. IIN_LEAK 2.6 V 10 nA At 150C 100 Cycles At 85C 100k Cycles At 100C 10 Years Sensor connection and short check must be disabled. nWRI_EEP Data Retention tWRI_EEP Parameters for A/D Converter ADC Resolution rADC Integral Nonlinearity (INL) 1) Differential Nonlinearity (DNL) * 1.3.5. dB Parameters for EEPROM Number Write Cycles 1.3.4. ppm/K Parameters for Analog Front-End (AFE) Leakage Current Pin VBP,VBN 1.3.3. mA INLADC Based on ideal slope DNLADC 14 Bit -4 +4 LSB -1 +1 LSB Parameters for Analog Output (DAC and Buffer) Max. Output Current IOUT Max. current maintaining accuracy Resolution Res Referenced to VDD Absolute Error EABS DAC input to output Differential Nonlinearity * DNL No missing codes -0.9 Upper Output Voltage Limit VOUT RL = 5 k 95% Lower Output Voltage Limit VOUT With 5k pull down, 0 to1V output Output Short Circuit Protection Limit ISC Analog Output Noise Peak-to-Peak VNOISE,PP Data Sheet October 9, 2013 Depends on operating conditions. Short circuit protection must be enabled via Diag_cfg (EEPROM word [102:100]). See section 2.4.2. Shorted input 2.2 mA 12 Bit ±0.2% VDD +3.0 LSB12Bit VDD 16.5mV mV 40 mA 5 ±1LSB mV 3 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 9 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Parameter 1.3.6. Symbol Min Typ Max Unit Diagnostics Upper diagnostic output level VDIA,H Lower diagnostic output level VDIA,L Minimum load resistor for power 2) loss 1.3.7. Conditions RL,OUT_PS 97.5% VDD 2.5% Pull-up or pull-down in Analog Output Mode 5 VDD k External Temperature Measurement External Temperature (ExtTemp) Signal Input Range VTSE 150 800 mV Required External Temperature Diode Sensitivity STTSE 1.9 3.25 mV/K Temperature Span with External Temperature Diode TTSE_SP -50 150 °C 3.9 kΩ 1 15 nF 0 0.2 VDD 1.3.8. Parameters for ZACwire™ Serial Interface ™ ZACwire Line Resistance * ™ RZAC,load ZACwire Load Capacitance * CZAC,load Voltage Level Low * VZAC,low Voltage Level High * VZAC,low 1.3.9. The rise time must be tZAC,rise = 2 RZAC,load CZACload 5µs. If using a pull-up resistor instead of a line resistor, it must meet this specification. The absolute maximum for CZACload is 15nF. 0 0.8 1 VDD Parameters for System Response tSTA Power-up to output Update_rate = 1 kHz (1 ms) Response Time – Analog Output tRESP-A Update_rate = 1 kHz (1 ms) Response and Transmission Time for Digital Output tRES, DIG Varies with update rate. Value given at fastest rate. Start-Up-Time Sampling Rate fS 1 8 ms 2 ms 1.6 ms Update_rate = 1 kHz (1 ms) 1000 Hz Overall Linearity Error– Digital ELIND Bridge input to output 0.025 0.04 % Overall Linearity Error – Analog ELINA Bridge input to output 0.1 0.2 % Overall Ratiometricity Error REout ±10%VDD, Not using Bsink feature 0.035 % Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 10 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Parameter Symbol Overall Accuracy – Digital (only IC, without sensor bridge) ACoutD 3), 4) Overall Accuracy – Analog (only IC, without sensor bridge) ACoutA Conditions Min Typ Max Unit -25°C to 85°C 0.1% -50°C to 150°C 0.25% -25°C to 85°C 0.25% -40°C to 125°C 0.35% -50°C to 150°C 0.5% %FSO %FSO Note: This is 4 LSBs for the 14-bit A-to-D conversion. This results in absolute accuracy to 12-bits on the A-to-D result. Non-linearity is typically better at temperatures less than 125°C. When using a pull-down resistor as the load resistor, the power loss detection diagnostic for loss of VSS cannot be assured at R L=5kΩ; RL=10kΩ is recommended for this configuration. 1) 2) Not included is the quantization noise of the DAC. The 12-bit DAC has a quantization noise of ½ LSB = 0.61mV (@ 5V VDD) = 0.0125%. Analog output range 2.5% to 95% 3) 4) 1.4. Analog Inputs versus Output Resolution The ZSC31015 has a fully differential chopper-stabilized pre-amplifier with four programmable gain settings. The output of the pre-amplifier feeds into a 14-bit charge-balanced ADC. Span, offset, temperature, and non-linearity correction are performed in the digital domain. Then the resulting corrected bridge value can be output in analog form through a 12-bit DAC or as a 16-bit serial digital packet. The resolution of the output depends on the input span (bridge sensitivity) and the analog gain setting programmed. Digital gains can vary from [0,32). Analog gains available are 6, 24, 48, and 96. Note: At higher analog gain settings, there will be higher output resolution, but the ability of the ZSC31015 to handle large offsets decreases. This is expected because the offset is also amplified by the analog gain and can therefore saturate the ADC input. The following tables outline the guaranteed minimum resolution for a given bridge sensitivity range. Table 1.1 ADC Resolution Characteristics for an Analog Gain of 6 Analog Gain 6 Input Span [mV/V] Min 1) Typ Max Allowed Offset 1 (+/- % of Span) Minimum Guaranteed Resolution [Bits] 57.8 80.0 105.8 38% 12.4 50.6 70.0 92.6 53% 12.2 43.4 60.0 79.4 73% 12.0 36.1 50.0 66.1 101% 11.7 28.9 40.0 52.9 142% 11.4 21.7 30.0 39.7 212% 11.4 In addition to Tco, Tcg. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 11 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Table 1.2 ADC Resolution Characteristics for an Analog Gain of 24 Analog Gain 24 Input Span [mV/V] Min 1) Typ Max Allowed Offset 1 (+/- % of Span) Minimum Guaranteed Resolution [Bits] 18.1 25.0 33.1 17% 12.7 14.5 20.0 26.5 38% 12.4 7.2 10.0 13.2 142% 11.4 3.6 5.0 6.6 351% 10.4 1.8 2.5 3.3 767% 9.4 0.9 1.2 1.6 1670% 8.4 In addition to Tco, Tcg. Table 1.3 Important Note: The yellow shadowed fields indicate that for these input spans with the selected analog gain setting, the quantization noise is higher than 0.1% FSO. ADC Resolution Characteristics for an Analog Gain of 48 Analog Gain 48 Input Span [mV/V] Min 1) Typ Max Allowed Offset 1 (+/- % of Span) Minimum Guaranteed Resolution [Bits] 10.8 15.0 19.8 3% 13.0 7.2 10.0 13.2 38% 12.4 4.3 6.0 7.9 107% 11.7 2.9 4.0 5.3 194% 11.1 1.8 2.5 3.3 351% 10.4 1.0 1.4 1.85 678% 9.6 0.72 1.0 1.32 976% 9.1 In addition to Tco, Tcg. Data Sheet October 9, 2013 Important Note: The yellow shadowed fields indicate that for these input spans with the selected analog gain setting, the quantization noise is higher than 0.1% FSO. © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 12 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Table 1.4 ADC Resolution Characteristics for an Analog Gain of 96 Analog Gain 96 Input Span [mV/V] 1) Allowed Offset 1 (+/- % of Span) Minimum Guaranteed Resolution [Bits] Min Typ Max 4.3 6.0 7.9 21% 12.7 2.9 4.0 5.3 64% 12.1 1.8 2.5 3.3 142% 11.4 1.0 1.4 1.85 306% 10.6 0.72 1.0 1.32 455% 10.1 In addition to Tco, Tcg. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 13 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 2 Circuit Description 2.1. Signal Flow and Block Diagram The ZSC31015 resistive bridge sensor interface ICs were specifically designed as cost-effective solutions for sensing in building automation, automotive *, industrial, office automation and white goods applications. The ZSC31015 employs ZMDI’s high precision bandgap with proportional-to-absolute-temperature (PTAT) output; low-power 14-bit analog-to-digital converter (ADC, A2D, A-to-D); and an on-chip DSP core with EEPROM to precisely calibrate the bridge output signal. Three selectable outputs, two analog and one digital, offer the ultimate in versatility across many applications. The ZSC31015 rail-to-rail ratiometric analog Vout signal (0V to ~5 V Vout @ VDD=5V) suits most building automation and automotive requirements (12-bit resolution). Typical office automation and white goods applications require the 0 to ~1V Vout signal, which in the ZSC31015 is referenced to the internal bandgap. The ZSC31015 is capable of running in high-voltage (5.5 to 30V) systems when combined with an external JFET. Direct interfacing to P controllers is facilitated via ZMDI’s single-wire serial ZACwire™ digital interface. Figure 2.1 ZSC31015 Block Diagram JFET1 (Optional if supply is 2.7 to 5.5 V) S 0.1 F VDD (2.7 to 5.5 V) Sensor Diagnostics Temperature Reference VDD Regulator Ext Temp Bsink INMUX PREAMP Power Save EEPROM with Charge Pump POR/Oscillator 12-Bit DAC ZSC31015 A VBN (Optional) Vgate RBicdLite PTAT VBP Optional Ext. Diode for Temp 5.5 V to 30 V VSUPPLY D _ D 14-Bit ADC Digital Core SIGTM + OUTBUF1 ZACwireTM Interface 0 V to 1 V Ratiometric Rail-to-Rail OWI/ZACwireTM Power Lost Diagnostic Analog Block VSS Digital Block * Not AEC-Q100-qualified. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 14 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 2.2. Analog Front End 2.2.1. Bandgap/PTAT and PTAT Amplifier The highly linear Bandgap/PTAT section provides the PTAT signal to the ADC, which allows accurate temperature conversion. In addition, the ultra-low ppm Bandgap provides a stable voltage reference over temperature for the operation of the rest of the IC. If the bridge is not near the ZSC31015, an external diode can be used for temperature measurement/compensation. The temperature signal (internal PTAT or external diode) is amplified through a path in the Pre-Amp and fed to the ADC for conversion. The most significant 12-bits of this converted result are used for temperature measurement and temperature correction of bridge readings. When temperature is output in Digital Mode, only the most significant 8 bits are given. When external temperature is selected, add a diode from the ExtTemp pin to ground. The diode is biased with approximately 50µA during temperature measurement cycles. The voltage level on ExtTemp is amplified through the Pre-Amp and converted by the ADC. Ensure that the ExtTemp signal is in the range of 150mV to 800mV to o o prevent saturation of the ADC. If the selected diode has a sensitivity in the range of 1.9mV/ C to 3.25mV/ C, a o o o corrected temperature output (in Digital Mode) can be achieved for a 200 C temperature span (-50 C to 150 C). 2.2.2. Bridge Supply The voltage-driven bridge is usually connected to VDD and ground. As a power savings feature, the ZSC31015 also includes a switched transistor to interrupt the bridge current via pin 1 (Bsink). The transistor switching is synchronized to the analog-to-digital conversion and released after finishing the conversion. To utilize this feature, the low supply of the bridge should be connected to Bsink instead of ground. Depending on the programmable update rate, the average current consumption (including bridge current) can be reduced to approximately 20%, 5%, or 1%. Note: this feature has no power savings benefit if using the fastest update rate mode. 2.2.3. PREAMP Block The differential signal from the bridge is amplified through a chopper-stabilized instrumentation amplifier with very high input impedance designed for low noise and low drift. This pre-amp provides gain for the differential signal and re-centers its DC to VDD/2. The output of the Pre-Amp block is fed into the ADC. The calibration sequence performed by the digital core includes an auto-zero sequence to null any drift in the Pre-Amp state over temperature. The Pre-Amp can be set to a gain of 6, 24, 48, or 96 through an EEPROM setting. The inputs to the Pre-Amp from (VBN/VBP pins) can be reversed via an EEPROM configuration bit. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 15 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 2.2.4. Analog-to-Digital Converter (ADC) nd A 14-bit/1ms 2 order charge-balancing ADC is used to convert signals coming from the pre-amplifier. The converter, designed in full differential switched capacitor technique, is used for converting the various signals in the digital domain. This principle offers the following advantages: High noise immunity because of the differential signal path and integrating behavior Independence from clock frequency drift and clock jitter Fast conversion time due to second-order mode Four selectable values for the zero point of the input voltage allow conversion to adapt to the sensor’s offset parameter. With the Reverse Input Polarity Mode and the negative digital gain options, this results in seven possible zero point adjustments (not eight because the -1/2,1/2 offset setting is the same regardless of gain polarity). The conversion rate varies with the programmed update rate. The fastest conversation rate is 1k samples/s and the response time is then 1ms. Based on a best fit, the Integral Nonlinearity (INL) is less than 4 LSB 14Bit. 2.3. Digital Signal Processor A digital signal processor (DSP) is used for processing the converted bridge data as well as performing temperature correction and computing the temperature value for output on the digital channel. The digital core reads correction coefficients from EEPROM and can correct for the following: Bridge Offset Bridge Gain Variation of Bridge Offset over Temperature (Tco) Variation of Bridge Gain over Temperature (Tcg) A single second order effect (SOT) (Second Order Term) The EEPROM contains a single SOT that can be applied to correct one and only one of the following: 2nd order behavior of bridge measurement 2nd order behavior of Tco 2nd order behavior of Tcg Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 16 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features If the SOT applies to correcting the bridge reading, then the correction formula for the bridge reading is represented as a two-step process as follows: ZB Gain_ B(1 T Tcg) (BR _ Raw Offset _ B T Tco) (1) BR ZB(1.25 SOT ZB) (2) Where: Note BR = Corrected Bridge reading that is output as digital or analog on the SIG ZB = Intermediate result in the calculations BR_Raw = Raw Bridge reading from ADC T_Raw = Raw Temp reading converted from PTAT signal or external diode Gain_B = Bridge Gain term TM Offset_B = Bridge Offset term Tcg = Temperature Coefficient Gain Tco = Temperature Coefficient Offset T = (T_Raw – TSETL) TSETL = T_Raw reading at which low calibration was performed (typically 25°C) SOT = Second-Order Term pin For solving equation (1) the following condition must be met: BR _ Raw BR / Gain_ B If this condition is not met, the analog Pre-Amp Gain must be set to a smaller value because a negative Offset_B is not supported. If the SOT applies to correcting the 2 nd order behavior of Tco, then the formula for bridge correction is as follows: BR Gain_ B(1 T Tcg) [BR _ Raw Offset _ B T(SOT T Tco)] If the SOT applies to correcting the 2 nd (3) order behavior of Tcg, then the formula for bridge correction is as follows: BR Gain_ B[1 T(SOT T Tcg)] [BR _ Raw Offset _ B T Tco] (4) The bandgap reference gives a very linear PTAT signal, so temperature correction can always simply be accomplished with a linear gain and offset term. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 17 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Corrected Temperature Reading: T Gain_ T(T _ Raw Offset _ T) (5) Where: T_Raw 2.3.1. = Raw Temperature reading converted from PTAT signal or external diode Offset_T = Offset Coefficient for Temperature Gain_T Gain Coefficient for Temperature = EEPROM The EEPROM contains the calibration coefficients for gain and offset, etc., and the configuration bits, such as output mode, update rate, etc. The ZSC31015 also offers three user-programmable storage bytes for module traceability. When programming the EEPROM, an internal charge pump voltage is used; therefore a high voltage supply is not needed. The EEPROM is implemented as a shift register. During an EEPROM read, the contents are shifted 8 bits before each transmission of one byte occurs. The charge pump is internally regulated to 12.5 V, and the programming time is 6ms. See section 2.6.1 regarding EEPROM signatures for verifying EEPROM integrity. Note: EEPROM writing can only be performed at temperatures lower than 85ºC. 2.3.2. One-Wire Interface – ZACwire™ The IC communicates via a one-wire serial interface. There are different commands available for the following: Reading the conversion result of the ADC (Get_BR_Raw, Get_T_Raw) Calibration commands Reading from the EEPROM (“dump” of entire contents) Writing to the EEPROM (trim setting, configuration, and coefficients) 2.4. Output Stage 2.4.1. Digital to Analog Converter (Output DAC) with Programmable Clipping Limits A 12-bit DAC based on sub-ranging resistor strings is used for the digital-to-analog output conversion in the analog ratiometric and absolute analog voltage modes. Options during calibration configure the system to operate in either of these modes. The design allows for excellent testability as well as low power consumption. The DAC allows programming a lower and upper clipping limit (Low_Clip_Lim and Up_Clip_Lim bit fields respectively; see section 3.5) for the output signal (analog and digital). The internal 14-bit calculated bridge value is compared against the 14-bit value formed by {11,Up_Clip_Lim[6:0],11111} for the upper limit and {00,Low_Clip_Lim[6:0],00000} for the lower limit. If the calculated bridge value is higher than the upper limit or less than the lower limit, the analog output value is clipped to this value; otherwise it is output as is. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 18 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Example for the upper clipping level: If the Up_Clip_Lim[6:0] = 0000000, then the 14-bit value used for the clipping threshold is 11000000011111. This is 75.19% of full scale. Since there are 7 bits of upper clipping limit, there are 127 possible values between 75.19% and 100%. Therefore the resolution of the clipping limits 0.195%. Example for the lower clipping level: If the Low_Clip_Lim[6:0] = 1111111, then the 14-bit value used for the clipping threshold is 00111111100000. This is 24.8% of full scale. Since there are 7 bits of lower clipping limit, there are 127 possible values between 0 and 24.8%. Therefore the resolution of the lower clipping limit is 0.195%. Figure 2.2 shows the data timing of the DAC output for the update rate setting 00. Figure 2.2 DAC Output Timing for Highest Update Rate Settling Time 64 s AD Conversion 768 s Calculation 160 s Settling Time 64 s AD Conversion 768 s Calculation 160 s DAC output occurs here 2.4.2. DAC output next update Output Buffer A rail-to-rail op amp configured as a unity gain buffer can drive resistive loads (whether pull-up or pull-down) as low as 5k and capacitances up to 15nF (for pure analog output). In addition, to limit the error due to amplifier offset voltage, an error compensation circuit is included which tracks and reduces offset voltage to < 1mV. The output of the ZSC31015 output can be permanently shorted to VDD or VSS without damaging the device. The output driver contains a current-limiting block that detects a hard short and limits the current to a safe level. The short circuit protection current can vary from a minimum of 3mA to a maximum of 40mA depending on operating conditions. Output short circuit protection can be enabled via Diag_cfg (EEPROM [102:100]). Enabling this protection is recommended when using the analog output. 2.4.3. Voltage Reference Block A linear regulator control circuit is included in the Voltage Reference Block to interface with an external JFET to allow operation in systems where the supply voltage exceeds 5.5V. This circuit can also be used for over-voltage protection. The regulator set point has a coarse adjustment controlled by the JFET_cfg EEPROM bits that can adjust the set point around 5.0 or 5.5V (See Table 3.5 for bit locations and section 2.3.1 regarding writing to the EEPROM.). The 1V trim setting (see below) can also act as a fine adjust for the regulation set point. The 5V reference can be trimmed within +/-15mV. Note: If using the external JFET for over-voltage protection purposes (i.e., 5V at JFET drain and expecting 5V at JFET source), there will be a voltage drop across the JFET; therefore ratiometricity will be slightly compromised depending on the rds(on) of the chosen JFET. A Vishay J107 is the best choice because it has only an 8mV drop worst case. If using as regulation instead of over-voltage protection, a MMBF4392 or BSS169 also works well. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 19 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features The Voltage Reference Block uses the absolute reference voltage provided by the bandgap to produce two regulated on-chip voltage references. A 1V reference is used for the output DAC high reference when the part is configured in 0-1V Analog Output Mode. For this reason, the 1V reference must be very accurate and includes trim so that its value can be trimmed within +/- 3mV of 1.00V. The 1V reference is also used as the on-chip reference for the JFET regulator block. The regulation set point of the JFET regulator can be fine-tuned using the 1V trim. The reference trim setting is selected with the 1V_Trim/JFET_Trim bits in EEPROM. See Table 3.5 for bit locations. Table 2.1 shows the order of trim codes with 0111 for the lowest reference voltage and 1000 for the highest reference voltage. Important: Optimal reference trim is determined during wafer-level testing and final package testing. Back-up copies of these bits are stored in bits in the CUST_ID0 bits for applications requiring accurate references. In this case, see section 5 for important notes and instructions for verifying the integrity of the 1V_Trim/JFET_Trim bits and if necessary, restoring the value from the CUST_ID0 bits before calibration. Table 2.1 1V Reference Trim (1V vs. Trim for Nominal Process Run) 1Vref/ 5Vref_trim3 1Vref/ 5Vref_trim2 1Vref/ 5Vref_trim1 1Vref/ 5Vref_trim0 Highest Reference Voltage 1 0 0 0 … 1 0 0 1 … 1 0 1 0 … 1 0 1 1 … 1 1 0 0 … 1 1 0 1 … 1 1 1 0 … 1 1 1 1 … 0 0 0 0 … 0 0 0 1 … 0 0 1 0 … 0 0 1 1 … 0 1 0 0 … 0 1 0 1 … 0 1 1 0 Lowest Reference Voltage 0 1 1 1 Order Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 20 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 2.5. Clock Generator / Power-On Reset (CLKPOR) If the power supply exceeds 2.5V (maximum), the reset signal de-asserts and the clock generator starts working at a frequency of approximately 512kHz (±20%). The exact value only influences the conversion cycle time and communication to the outside world but not the accuracy of signal processing. In addition, to minimize the oscillator error as the VDD voltage changes, an on-chip regulator is used to supply the oscillator block. 2.5.1. Trimming the Oscillator Settings for the Osc_Trim bits in EEPROM fine-tune the oscillator frequency. See Table 3.5 for bit locations and Table 2.2 for possible settings. The default value is 0HEX to ensure communication on start-up. Important: Optimal oscillator trimming is determined during wafer-level testing and final package testing, and this part-specific factory value, which can be copied to Osc_Trim, is stored in bits in the CUST_ID1 and CUST_ID2 EEPROM bits for applications requiring optimal response time. In this case, see section 5 for important notes and instructions for copying these optimal values to the Osc_Trim bits before calibration. It is strongly recommended TM that only the default value or the factory trim value be used because ZACwire communication is not guaranteed at different oscillator frequencies. Table 2.2 Oscillator Trimming Osc_Trim Bits Delta Frequency (kHz) 100 +385 101 +235 110 +140 111 +65 000 Nominal 001 -40 010 -76 011 -110 Example: Programming 011B the trimmed frequency = nominal value – 110 kHz. 2.6. Diagnostic Features The ZSC31015 offers a full suite of diagnostic features to ensure robust system operation in the most “missioncritical” applications. If the part is programmed in Analog Output Mode, then diagnostic states are indicated by an output below 2.5% of VDD or above 97.5% of VDD. If the part is programmed in Digital Output Mode, then diagnostic states will be indicated by a transmission with a generated parity error. Table 2.3 gives a summary of the diagnostic features, which are explained in detail in the following sections. EEPROM settings that control diagnostic functions are given in section 3.5. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 21 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Table 2.3 Summary of Diagnostic Features Analog Diagnostic Level Detected Fault TM ZACwire Diagnostic Delay in Detection EEPROM signature Lower Generates parity error Loss of bridge positive Upper Generates parity error 2ms Loss of bridge negative Upper Generates parity error 2ms Open bridge connection Upper Generates parity error 2ms Bridge input short Upper Generates parity error 2ms ExtTemp pin open Lower Generates parity error 300ms Lower Generates parity error 300ms ExtTemp pin shorted to BP/BN Upper Generates parity error 3ms Loss of VDD Lower Transmissions stop Dependent on RL and CL Loss of VSS Upper Transmissions stop Dependent on RL and CL ExtTemp pin shorted to PWR/GND † 2.6.1. 10ms after power-on EEPROM Integrity The contents of the EEPROM are protected by an 8-bit LFSR signature (linear feedback shift register). This signature is regenerated and stored in EEPROM every time EEPROM contents are changed. This signature is generated and checked for a match after Power-On-Reset prior to entering Normal Operation Mode. If the generated signature fails to match, the part will output a diagnostic state on the output. In addition to an extensive temporal and code interlock mechanism used to prevent false writes to the EEPROM, the ZSC31015 offers an EEPROM lock mechanism for high-security applications. When EEPROM bits 105:103 are programmed with “011” or “110,” this 3-bit field will permanently disable the VPP charge pump and will not allow further writes to the EEPROM. See Table 2.3 in section 2.6 for more information. 2.6.2. Sensor Connection Check Four dedicated comparators permanently check the range of the bridge inputs (BP/BN) to ensure they are within the envelope of 0.8V to 0.85VDD during all conversions. The two sensor inputs have a switched ohmic path to ground and if left floating, would be discharged. If any of the wires connecting the bridge break, this mechanism will detect it and put the ZSC31015 in a diagnostic state. This same diagnostic feature can also detect a short between BP/BN and the ExtTemp signal if an external diode is being used for temperature measurement. See Table 2.3 in section 2.6 for more information. † A short from ExtTemp to BP/BN might not be detected in some circuit configurations. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 22 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 2.6.3. Sensor Short Check If a short occurs between BP/BN (bridge inputs), it would normally produce an in-range output signal and therefore would not be detected as a fault. This diagnostic mode, if enabled, will deliberately look for such a short. After the measurement cycle of the bridge, it will deliberately pull the BP bridge input to ground for 4sec. At the end of this 4sec window, it will check to see if the BN input “followed” it down below the 0.8V comparator checkpoint. If so, a short must exist between BP/BN, and the part will output a diagnostic state. The bridge will have a minimum of 480sec recovery time prior to the next measurement. See Table 2.3 in section 2.6 for more information. 2.6.4. Power Loss Detection If the power or GND connection to the module containing the sensor bridge and the ZSC31015 is lost, the ZSC31015 will output a diagnostic state if a pull-up or pull-down terminating resistor greater than or equal to 5k is connected in the final application. This diagnostic mode only works when the part is configured in Analog Output Mode. See Table 2.3 in section 2.6 for more information. 2.6.5. ExtTemp Connection Checks When external temperature is selected and connection checking is enabled, the part performs range checking on the converted temperature value. If the internal ADC reading of the temperature is less than 1/32 of full scale or greater than 63/64 of full scale then a diagnostic state is asserted. If the ExtTemp pin is shorted to ground, the ADC reads less than 1/32. Because 100µA is sourced onto the ExtTemp pin during conversions, it naturally pulls up during these times. If the ExtTemp pin is open, it produces an ADC reading greater than 63/64 of full scale. Both these bad connection conditions would be detected and result in a diagnostic output. If internal temperature is selected or sensor connection check is not enabled, then this diagnostic check is not enabled. See Table 2.3 in section 2.6 for more information. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 23 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 3 Functional Description 3.1. General Working Mode The command/data transfer takes place via the one-wire SIG™ pin using the ZACwire protocol. TM serial communication After power-on, the ZSC31015 waits for 3ms (= Command window) for the Start_CM command. Without this command, the Normal Operation Mode (NOM) starts. In this mode, raw bridge values are converted, and the corrected values are presented on the output in analog or digital format (depending on the configuration stored in EEPROM). Command Mode (CM) can only be entered during the 3ms command window after power-on. If the ZSC31015 receives the Start_CM command during the command window, it remains in the Command Mode. The CM allows changing to one of the other modes via command. After the command Start_RW, the ZSC31015 is in the Raw Mode (RM). Without correction, the raw values are transmitted to the digital output in a predefined order. The RM can only be stopped by a power-off. RM is used by the calibration software for collection of raw bridge and temperature data so the correction coefficients can be calculated. If diagnostic features are enabled and a diagnostic fault is detected, diagnostic states are indicated as follows depending on the programmed mode: In Analog Output Mode, diagnostic states are indicated by an output below 2.5% of VDD or above 97.5% of VDD. In Digital Output Mode, diagnostic states will be indicated by a transmission with a generated parity error. For more details see section 2.6. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 24 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Figure 3.1 General Working Mode Power ON Command Window (3 ms); send Start_CM Start_CM No Command Normal Operation Mode Start_NOM Command Mode Start_RM Raw Mode No commands possible Measurement cycle stopped Measurement cycle Measurement cycle Full command set SigTM pin provides raw bridge and temperature values in the format: • Bridge_high (1st byte) • Bridge_low (2nd byte) • Temp (3rd byte) Conditioning calculations (corrected bridge and temperature values) Command routine will be processed after each command Depending on configuration, the SigTM pin is • 0 V to 1 V; • Rail-to-rail ratiometric; or • Digital output Diagnostic functions Power OFF Error Detection Diagnostic State* * See section 2.6. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 25 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 3.2. ZACwire™ Communication Interface 3.2.1. Properties and Parameters Table 3.1 No. Pin Configuration and Latch-Up Conditions Parameter Symbol 1 Pull-up resistor (on-chip) RZAC,pu 2 Pull-up resistor (external) RZAC,pu_ext 3 ZACwire™ rise time 4 ZACwire™ line resistance 1) 1) Typ Max 30 150 Unit Comments kΩ On-chip pull-up resistor switched on during Digital Output Mode and during CM Mode (first 3 ms after power up). Ω If the master communicates via a pushpull stage, no pull-up resistor is needed; otherwise, a pull-up resistor with a value of at least 150 Ω must be connected. tZAC,rise 5 µs Any user RC network included in the Sig™ path must meet this rise time. RZACload 3.9 kΩ Also see section 1.3.8. 1 15 nF Also see section 1.3.8. 0 0.2 VDD Rail-to-rail CMOS driver. VDD Rail-to-rail CMOS driver. 5 ZACwire™ load capacitance 6 Voltage low level VZAC,low 7 Voltage high level VZAC,high 1) Min CZAC,load 0 0.8 1 The rise time must be tZAC,rise = 2 RZACload CZACload 5 s . If using a pull-up resistor instead of a line resistor, it must meet this specification. The absolute maximum for CZACload is 15nF. 3.2.2. Bit Encoding Figure 3.2 Manchester Duty Cycle Bit Window 104.2µsec @ 9.6 kHz baud 40 µsec @ 26kHz baud Start Bit Start bit = 50% duty cycle used to set up strobe time Logic 1 Logic 1 = 75% duty cycle Logic 0 Logic 0 = 25% duty cycle Stop Time The ZACWire™ bus will be held high for 32μs (nominal) between consecutive data packets regardless of baud rate. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 26 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 3.2.3. Write Operation from Master to ZSC31015 The calibration master sends a 19-bit packet frame to the IC. Figure 3.3 19-Bit Write Frame 19-bit Frame (WRITE) S 7 6 5 4 3 2 1 0 P 7 6 5 4 3 2 1 0 P Command Byte Data Byte S Start Bit P Parity Bit of Command or Data Byte 2 Command Bit (example: Bit 2) 2 Data Bit (example: Bit 2) The incoming serial signal will be sampled at a 512 kHz clock rate. This protocol is very tolerant to clock skew, and can easily tolerate baud rates in the 6 kHz to 48 kHz range. 3.2.4. ZSC31015 Read Operations The incoming frame will be checked for proper parity on both, command and data bytes, as well as for any edge time-outs prior to a full frame being received. Once a command/data pair is received, the ZSC31015 will perform that command. After the command has been successfully executed by the ZSC31015, it will acknowledge success by a transmission of an A5 HEX-byte back to the master. If the master does not receive an A5 HEX transmission within 130 ms of issuing the command, it must assume the command was either improperly received or could not be executed. Figure 3.4 Read Acknowledge 1 DATA Byte Packet (10-bit byte A5H) S Start Bit S 1 0 1 0 0 1 0 1 P P Parity Bit of Data Byte Data Byte 0 Data Bit (Low) 1 Data Bit (High) Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 27 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features The ZSC31015 transmits 10-bit bytes (1 start bit, 8 data bits, 1 parity bit). During calibration and configuration, transmissions are normally either A5HEX or data. A5HEX indicates successful completion of a command. There are two different digital output modes configurable (digital output with temperature, and digital output with only bridge data). During Normal Operation Mode, if the part is configured for digital output of the bridge reading, it first transmits the high byte of bridge data, followed by the low byte. The bridge data is 14 bits in resolution, so the upper two bits of the high byte are always zero-padded. There is a half stop bit time between bytes in a packet. This means that for the time of a half a bit width, the signal level is high. Figure 3.5 Digital Output (NOM) Bridge Readings 2 DATA Byte Packet (Digital Bridge Output ) S Start Bit S 0 0 5 4 3 2 1 0 P Stop S 7 6 5 4 3 2 1 0 P Data Byte Bridge High Data Byte Bridge Low P Parity Bit of Data Byte 2 Data Bit (example: Bit 2) Stop 32µs The second option for Digital Output Mode is digital output bridge reading with temperature. It will be transmitted as 3 data packets. The temperature byte represents an 8-bit temperature quantity spanning from -50 to 150°C. Figure 3.6 Digital Output (NOM) Bridge Readings with Temperature 3 DATA Byte Packet (Digital Bridge Output with Temperature ) S 0 0 5 4 3 2 1 0 P Stop S 7 6 5 4 3 2 1 0 P Stop S 7 6 5 4 3 2 1 0 P Data Byte Bridge High Data Byte Bridge Low Data Byte Temperature The EEPROM transmission occurs in a packet with 20 data bytes, as shown in Figure 3.7. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 28 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Figure 3.7 Read EEPROM Contents 20 DATA Byte Packet (Read EEPROM) S 7 6 5 4 3 2 1 0 P Stop S 7 6 5 4 3 EEPROM Byte 1 EEPROM Byte 2 ... 5 4 3 2 1 0 P Stop S 7 6 5 4 3 2 1 0 P Stop S 1 0 1 0 0 1 0 1 P EEPROM Byte 18 EEPROM Byte 19 Data Byte A5H There is a variable idle time between packets. This idle time varies with the update rate setting in EEPROM. Figure 3.8 Transmission of a Number of Data Packets Packet Transmission (This example shows 2 DATA packets) 210P IDLE IDLE IDLE S 0 0 5 4 3 2 1 0 PStop S 7 6 5 4 3 2 1 0 P S 0 0 5 4 3 2 1 0 PStop S 7 6 5 4 3 2 1 0 P S0054 Time Time Time The table below shows the idle time between packets versus the update rate. This idle time can vary by nominal +/-15% between parts and over a temperature range of -50 to 150ºC. Table 3.2 Special Measurement/Idle Time between Packets versus Update Rate Update Rate Setting Idle Time between Packets Special Measurement 00 1ms Every 128 bridge measurements 01 4.85ms Every 64 bridge measurements 10 22.5ms Every 16 bridge measurements 11 118ms Every 8 bridge measurements Transmissions from the IC occur at one of two speeds depending on the update rate programmed in EEPROM. If the user chooses one of the two fastest update rates (1 ms or 5 ms) then the baud rate of the digital transmission will be 32 kHz (minimum 26kHz). If, however, the user chooses one of the two slower update rates (25 ms or 125 ms), then the baud rate of the digital transmission will be 8 kHz (maximum 9.6kHz). The total transmission time for both digital output configurations is shown in Table 3.3. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 29 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Table 3.3 Total Transmission Time for Different Update Rate Settings and Output Configuration Update Rate Baud Rate* Idle Time Transmission Time – Bridge Only Readings Transmission Time – Bridge & Temperature Readings 1 ms (1 kHz) 32 kHz 1.0 ms 20.5 bits 31.30 µs 1.64 ms 31.0 bits 31.30 µs 1.97 ms 5 ms (200 Hz) 32 kHz 4.85 ms 20.5 bits 31.30 µs 5.49 ms 31.0 bits 31.30 µs 5.82 ms 25 ms (40 Hz) 8 kHz 22.5 ms 20.5 bits 125.00 µs 25.06 ms 31.0 bits 125.00 µs 26.38 ms 125 ms (8 Hz) 8 kHz 118.0 ms 20.5 bits 125.00 µs 120.56 ms 31.0 bits 125.00 µs 121.88 ms * Typical values. Minimum baud rate for 1 ms or 5 ms: 26kHz; maximum baud rate for 25 ms or 125 ms: 9.6kHz. The temperature raw reading is performed less often than a bridge reading because the temperature changes more slowly. rd The 3 column in Table 3.2 shows the timing for the special measurements (temperature and bridge measurement) in the different update rate modes. For lower update rates, the output is followed by a power-down as shown in Figure 3.9. Figure 3.9 ZACwire™ Output Timing for Lower Update Rates Calculation 160 s ZACwireTM Output Power Down (determined by Update Rate) Power-On Settling 128 s Settling Time 64 s ADC Conversion 768 s Calculation 160 s ZACwireTM Output It is easy to program any standard microcontroller to communicate with the ZSC31015. ZMDI can provide sample code for a MicroChip PIC microcontroller. 3.2.5. High Level Protocol The ZSC31015 will listen for a command/data pair to be transmitted for the 3 ms after the de-assertion of its internal Power On Reset (POR). If a transmission is not received within this time frame, then it will transition to Normal Operation Mode (NOM). In the NOM, it will output bridge data in 0-1V analog, rail-to-rail ratiometric analog, or digital depending on how the part is currently configured. If the ZSC31015 receives a Start_CM command within the first 3 ms after the de-assertion of POR, then it will go into Command Mode (CM). In this mode, calibration/configuration commands will be executed. The ZSC31015 will acknowledge successful execution of commands by transmission of A5 HEX. The calibrating /configuring master will know a command was not successfully executed if no response is received after 130ms of issuing the command. Once in command interpreting/executing mode, the ZSC31015 will stay in this mode until power is removed or a Start NOM (Start Normal Operation Mode) command is received. The Start_CM command is used as an interlock mechanism to prevent a spurious entry into Command Mode on power up. The first command received within the 3ms window of POR must be a Start_CM command to enter into command interpreting mode. Any other commands will be ignored. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 30 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 3.3. Command/Data Bytes Encoding The 2-byte command sent to the ZSC31015 consists of 1 byte of command information and 1 byte of data information. Regardless of whether the command requires data or not, 2 bytes MUST be sent. Table 3.4 lists all the command/data pairings. (X=don’t care.) Table 3.4 Command/Data Bytes Encoding Note: Refer to Table 3.5 for the location in EEPROM for the bit fields (e.g., Gain_B) referenced in the table. Command Byte Data Description 00HEX XXHEX Read EEPROM command via SIG™ pin. 20HEX 5XHEX DAC Ramp Test Mode. Gain_B[13:3] contains the starting point, and the increment is (Offset_B/8). The increment will be added every 125µsec. 30HEX WDHEX Trim/Configure: 3 nibble determines what is trimmed/configured. The 4 nibble is data to be programmed. ‡ rd rd th 3 Nibble 4 Nibble Data W= What 0HEX DHEX Trim oscillator. Least significant 3 bits of data used. 1HEX DHEX Trim 1V reference. Least significant 4 bits of data used. D= Data 2HEX DHEX Offset Mode. Least significant 4 bits of data used. 3HEX DHEX Set output mode. Least significant 2 bits used. 4HEX DHEX Set update rate. Least significant 2 bits used. 5HEX DHEX Configure JFET regulation 6HEX DHEX Program the Tc_cfg register. Least significant 3 bits used. Most significant bit of data nibble should be 0. 7HEX DHEX Program EEPROM bits [99:96] {SOT_cfg,Pamp_Gain} DHEX 3HEX 0HEX,1HEX,2HEX 6HEX 4HEX,5HEX,7HEX EHEX ‡ § th DHEX Description Program EEPROM bits [105:103]: EEPROM locked! Int. PTAT used for temperature EEPROM unlocked, Int. PTAT used for temperature EEPROM locked! Ext. diode used for temperature EEPROM unlocked, Ext. diode used for temperature Program EEPROM bits [102:100] diag_cfg § 40HEX 00HEX Start NOM => Ends Command Mode; transition to Normal Operation Mode. 40HEX 10HEX Start_RM = Start the Raw Mode (RM) In this mode, if Gain_B = 800HEX and Gain_T = 80HEX, then the digital output will simply be the raw values of the ADC for the Bridge reading, and the PTAT conversion. 50HEX 90HEX Start_CM => Start the Command Mode; used to enter Command Interpret Mode. 60HEX YYHEX Program SOT (2 nd Order Term) For more details, refer to section 3.7. For more details, refer to section 3.5. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 31 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Command Byte Data Description 70HEX YYHEX Program TSETL (Set the MSB to 0.) 80HEX YYHEX Program Gain_B upper 7-bits (Set the MSB to 0.) 90HEX YYHEX Program Gain_B lower 8-bits A0HEX YYHEX Program Offset_B upper 6-bits (Set the two MSBs to 0.) B0HEX YYHEX Program Offset_B lower 8-bits C0HEX YYHEX Program Gain_T D0HEX YYHEX Program Offset_T E0HEX YYHEX Program Tco F0HEX YYHEX Program Tcg 08HEX YYHEX Program Upper Clipping Limit (Set the MSB to 0.) 18HEX YYHEX Program Lower Clipping Limit (Set the MSB to 0.) 28HEX YYHEX Program Cust_ID0 38HEX YYHEX Program Cust_ID1 48HEX YYHEX Program Cust_ID2 3.4. Calibration Sequence Although the ZSC31015 can work with many different types of resistive bridges, assume a pressure bridge is being used for the following discussion on calibration. Calibration essentially involves collecting raw bridge and temperature data from the ZSC31015 for different known pressures and temperatures. This raw data can then be processed by the calibration master (typically a PC) to compute the coefficients, and the calculated coefficients can then be written to the ZSC31015. ZMDI can provide software and hardware with samples to perform the calibration. There are three main steps to calibration: 1. Assigning a unique identification to the ZSC31015. This identification is programmed in EEPROM and can be used as an index into the database stored on the calibration PC. This database will contain all the raw values of bridge readings and temperature readings for that part, as well as the known pressure (for this application) and temperature the bridge was exposed to. This unique identification can be stored in a concatenation of the following EEPROM registers: Cust_ID0, Cust_ID1, Cust_ID2. These registers can also form a permanent serial number. 2. Data collection. Data collection involves getting raw data from the bridge at different known pressures and temperatures. This data is then stored on the calibration PC using the unique identification of the ZSC31015 as the index to the database. 3. Coefficient calculation and write. Once enough data points have been collected to calculate all the desired coefficients then the coefficients can be calculated by the calibrating PC and written to the ZSC31015. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 32 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Step 1 – Assigning Unique Identification Assigning a unique identification number is as simple as using the commands Program Cust_ID0, Program Cust_ID1 and Program Cust_ID2. These three 8-bit registers allow for more than 16 million unique devices. Gain_B must be programmed to 800HEX (unity) and Gain_T must be programmed to 80HEX (unity). Step 2 – Data Collection The number of unique (pressure, temperature) points that calibration must be performed at depends on the user’s needs. The minimum is a 2-point calibration, and the maximum is a 5-point calibration. To acquire raw data from the part, set the ZSC31015 to enter Raw Mode. This is done by issuing a Start_CM (Start Command Mode 5090HEX) command/data pair to the ZSC31015 followed by a Start_RM (Start Raw Mode 4010HEX) command/data pair with the LSB of the upper data nibble set. Now if the Gain_B term has been set to unity (800 HEX) and the Gain_T term has also been set to unity (80HEX), then the part will be in the Raw Mode and will output raw data on TM its SIG pin instead of corrected bridge and temperature. Capture several of these data points with the user’s calibration system (16 each of bridge and temperature is recommended) and average them. Store these raw bridge and temperature settings in the database along with the known pressure and temperature. The output format during Raw Mode is Bridge_High, Bridge_Low, Temp. Each of these is an 8-bit quantity. The upper 2-bits of Bridge_High are zero-filled. The Temp data (8-bits only) would not be enough information for accurate temperature calibration. Therefore the upper three bits of temperature information are not given, but rather assumed known. Therefore effectively 11-bits of temperature information are provided in this mode. Step 3 – Coefficient Calculations The math to perform the coefficient calculation is very complicated and will not be discussed in detail. There is a rough overview in section 3.6. ZMDI will provide software to perform the coefficient calculation. ZMDI can also provide source code for the algorithms in a C code format. After the coefficients are calculated, the final step is to write them to the EEPROM of the ZSC31015. The number of calibration points required can be as few as two or as many as five. This depends on the precision desired and the behavior of the resistive bridge in use. 1. 2-point calibration can be used if only a gain and offset term are needed for a bridge with no temperature compensation for either term. st 2. 3-point calibration would be used to obtain 1 order compensation for either a Tco or Tcg term but not both. nd 3. 3-point calibration could also be used to obtain 2 order correction for the bridge but no temperature compensation of the bridge output. st 4. 4-point calibration would be used to obtain 1 order compensation for both Tco and Tcg. st nd 5. 4-point calibration could also be used to obtain 1 order compensation for Tco and a 2 order correction for the bridge measurement. st st 6. 5-point calibration would be used to obtain both 1 order Tco correction and 1 order Tcg correction, plus nd nd nd a 2 order correction that could be applied to one and only one of the following: 2 order Tco, 2 order nd Tcg, or 2 order bridge. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 33 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 3.5. EEPROM Bits Table 3.5 shows the bit order and default settings for the EEPROM, which are programmed through the serial interface. See section 5 for important information for die/wafer customers. Table 3.5 EEPROM Range 2:0 ZSC31015 EEPROM Bits Description Osc_Trim Default Settings As of ww08/2009 Notes 0HEX See section 2.5 for details on oscillator trim. This default setting minimizes risk of communication failure on start-up. 100 => Fastest 101 => 3 clicks faster than nominal 110 => 2 clicks faster than nominal 111 => 1 click faster than nominal 000 => Nominal 001 => 1 click slower than nominal 010 => 2 clicks slower than nominal 011 => Slowest (Actual part-specific factory values for Osc_Trim are initially stored in bits in CUST_ID1 and CUST_ID2 for applications requiring optimal response time. See section 5 for important notes.) 6:3 1V_Trim/JFET_Trim ssssBIN See Table 2.1 in the “Voltage Reference Block” section. where “s” is the partspecific factory bit setting for the reference voltage trim value. (Back-up copies are stored in CUST_ID0 for applications requiring accurate references. See section 5 for important notes.) 10:7 Data Sheet October 9, 2013 A2D_Offset 3HEX The upper two bits are flip polarity and invert bridge input (negative gain) respectively. If both are used in conjunction, negative offset modes can be achieved. 00 => normal polarity, positive gain 01 => normal polarity, negative gain 10 => flip polarity, positive gain 11 => flip polarity, negative gain The lower two bits form the ADC offset selection. Offset selection: 11 => [-1/2,1/2] mode bridge inputs 10 => [-1/4,3/4] mode bridge inputs 01 => [-1/8,7/8] mode bridge inputs 00 => [-1/16,15/16] mode bridge inputs © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 34 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features EEPROM Range Description Default Settings As of ww08/2009 Notes 12:11 Output_Select 2HEX 00 => Digital (3 bytes with parity) Bridge High {00,[5:0]} Bridge Low [7:0] Temp [7:0] 01 => 0-1V Analog 10 => Rail-to-Rail Ratiometric 11 => Digital (2 bytes with parity) (No Temp) Bridge High {00,[5:0]} Bridge Low [7:0] 14:13 Update_Rate 2HEX 00 => 1 msec (1kHz) 01 => 5 msec (200Hz) 10 => 25 msec (40Hz) 11 => 125 msec (8 Hz) 16:15 JFET_cfg 3HEX 00 => No JFET regulation (lower power) 01 => No JFET regulation (lower power) 10 => JFET regulation centered around 5.0V 11 => JFET regulation centered around 5.5V (i.e., over-voltage protection) 31:17 Gain_B 198HEX Bridge Gain (also see bits 10:7): Gain_B[14] => multiply x 8 Gain_B[13:0] => 14-bit unsigned number representing a number in the range [0,8) 45:32 Offset_B 0HEX Unsigned 14-bit offset for bridge correction 53:46 Gain_T 80HEX Temperature gain coefficient used to correct PTAT or ExtTemp reading 61:54 Offset_T 0HEX Temperature offset coefficient used to correct PTAT or ExtTemp reading 68:62 TSETL 0HEX Stores Raw PTAT or ExtTemp reading at temperature in which low calibration points were taken 76:69 Tcg 0HEX Coefficient for temperature correction of bridge gain term: Tcg = 8-bit magnitude of Tcg term. Sign is determined by Tc_cfg (bits 87:85). 84:77 Tco 0HEX Coefficient for temperature correction of bridge offset term. Tco = 8-bit magnitude of Tco term. Sign and scaling are determined by Tc_cfg (bits 87:85) 87:85 Tc_cfg 0HEX This 3-bit term determines options for temperature compensation of the bridge. Tc_cfg[2] => If set, Tcg is negative Tc_cfg[1] => Scale magnitude of Tco term by 8, and if SOT applies to Tco, scale SOT by 8 Tc_cfg[0] => If set, Tco is negative Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 35 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features EEPROM Range Description Default Settings As of ww08/2009 Notes nd 95:88 SOT 0HEX 2 Order Term. This term is a 7-bit magnitude with sign. SOT[7] = 1 negative SOT[7] = 0 positive SOT[6:0] = magnitude [0-127] nd This term can apply to a 2 order Tcg, Tco or bridge correction. (See Tc_cfg above.) 99:96 {SOT_cfg, Pamp_Gain} 5HEX Bits [99:98] = SOT_cfg 00 = SOT applies to Bridge 01 = SOT applies to Tcg 10 = SOT applies to Tco 11 = Prohibited Bits [97:96] = Pre-Amp Gain 00 => 6 01 => 24 (default setting) 10 => 48 11 => 96 102:100 Diag_cfg 7HEX This 3-bit term applies to diagnostic features Diag_cfg[2] enable output short circuit protection. Diag _cfg[1] enable sensor short checking. Diag_cfg[0] enables sensor connection checking. 105:103 Lock_ExtTemp 0HEX EEPROM lock 011 or 110 => locked All other => unlocked When EEPROM is locked, the internal charge pump is disabled and the EEPROM can never be programmed again. Bit 105 (the MSB of this field) is also used for selecting external temperature measurement. 000,001,010,011=>Internal PTAT used for temp 100,101,110,111=>External diode used for temp 112:106 Up_Clip_Lim 7FHEX 7-bit value used to select an upper clipping limit for the output. It affects both analog and digital output. The 14-bit upper clipping limit value is comprised of {11,Up_Clip_Lim[6:0],11111}. 127 different clipping levels are selectable between 75.19% and 100% of VDD. 119:113 Low_Clip_Lim 0HEX 7-bit value used to select a lower clipping limit for the output. It affects both analog and digital output. The 14-bit lower clipping limit value is comprised of {00,Low_Clip_Lim[6:0],00000}. 127 different clipping levels are selectable between 0% and 24.8% of VDD. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 36 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features EEPROM Range 127:120 Description Cust_ID0 Default Settings As of ww08/2009 ssBIN where “s” is a partspecific factory bit setting. During factory testing, two back-up copies of the optimal setting for the 1V_Trim/JFET_Trim bits are stored in [123:120] and in [127:124]. See important notes in section 5. 135:128 Cust_ID1 xsss xsssBIN where “s” is a partspecific factory bit setting and x is “don’t care.” During factory testing, two copies of the optimal setting for the Osc_Trim bits are stored in [130:128] and in [134:132]. (Also in Cust_ID2.) See important notes in section 5. 143:136 Cust_ID2 xxxx xsssBIN where “s” is a partspecific factory bit setting and X is “don’t care.” During factory testing, a copy of the optimal setting for the Osc_Trim bits is stored in [138:136]. (Also in Cust_ID1.) See important notes in section 5. 151:144 ** Signature Notes Customer ID byte 0 Can be used to store a customer part identification number. Caution: If the application requires accurate voltage references, do not overwrite this byte until completing the procedures in section 5. Customer ID byte 1 Can be used to store a customer part identification number. Caution: If the application requires optimal response time, do not overwrite this byte until completing the procedures in section 5. Customer ID byte 2 Can be used to store a customer part identification number. Caution: If the application requires optimal response time, do not overwrite this byte until completing the procedures in section 5. ** 8-bit EEPROM signature. Generated through a LFSR . This signature is checked on power-on to ensure integrity of EEPROM contents. Linear feedback shift register Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 37 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 3.6. Calibration Math 3.6.1. Correction Coefficients All terms are calculated external to the ZSC31015 and then programmed to the EEPROM through the serial interface. Table 3.6 Correction Coefficients Coefficient Gain_B Offset_B Gain_T Offset_T Description Gain term used to compensate span of Bridge reading Offset term used to compensate offset of Bridge reading Gain term used to compensate span of Temp reading Offset term used to compensate offset of Temp reading SOT Second Order Term. The SOT can be applied as a second order correction term for one of the following: - Bridge measurement - Temperature coefficient of offset (Tco) - Temperature coefficient of gain (Tcg) The EEPROM bits 99:98 determine what SOT applies to. TSETL RAW_PTAT or ExtTemp reading (upper 7-bits) at low temperature at which calibration was performed (typically room temperature) Tcg Temperature correction coefficient of bridge gain term. This term has an 8-bit magnitude and a sign bit (Tc_cfg[2]. Tco Temperature correction coefficient of bridge offset term. This term has an 8-bit magnitude, a sign bit (Tc_cfg[0]), and a scaling bit (Tc_cfg[1]), which can multiply its magnitude by 8. 3.6.2. Interpretation of Binary Numbers for Correction Coefficients BR_Raw should be interpreted as an unsigned number in the set [0, 16383] with a resolution of 1. T_Raw should be interpreted as an unsigned number in the set [0, 16383], with a resolution of 4. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 38 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 3.6.2.1. Gain_B Interpretation Gain_B should be interpreted as a number in the set [0, 64]. The MSB (bit 14) is a scaling bit that will multiply the effect of the Gain_B[13:0] term by 8. The remaining bits Gain_B[13:0] represent a number in the range of [0,8) with Gain_B[13] having a weighting of 4, and each subsequent bit has a weighting of ½ the previous bit. Table 3.7 Gain_B [13:0] Weightings Bit Position Weighting 13 2 =4 12 2 =2 11 2 =1 10 2 … … 3 2 -8 2 2 -9 1 2 -10 0 2 -11 2 1 0 -1 Examples: The binary number: 010010100110001B = 4.6489; Gain_B[14] is 0BIN, so the number represented by Gain_B[13:0] is not multiplied by 8. The binary number: 101100010010110B = 24.586; Gain_B[14] is 1BIN, so the number represented by Gain_B[13:0] is multiplied by 8. 3.6.2.2. Offset_B Interpretation Offset_B is a 14-bit unsigned binary number. The MSB has a weighting of 8192. The following bits then have a weighting of: 4096, 2048, 1024 … Table 3.8 Offset_B Weightings Bit Position Weighting 13 8192 12 4096 11 2048 . . . 1 1 2 =2 0 2 =1 0 For example, the binary number 1111 1111 1100 = 4092. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 39 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 3.6.2.3. Gain_T Interpretation Gain_T should be interpreted as a number in the set [0,2]. Gain_T[7] has a weighting of 1, and each subsequent bit has a weighting of ½ the previous bit. Table 3.9 Gain_T Weightings Bit Position Weighting 7 2 =1 6 2 = 0.5 5 2 = 0.25 4 2 -3 3 2 -4 2 2 -5 1 2 -6 0 2 -7 0 -1 -2 3.6.2.4. Offset_T Interpretation Offset_T is an 8-bit signed binary number in two’s complement form. The MSB has a weighting of -128. The following bits then have a weighting of 64, 32, 16 … Table 3.10 Offset_T Weightings Bit Position Weighting 7 -128 6 2 = 64 5 2 = 32 4 2 = 16 3 2 =8 2 2 =4 1 2 =2 0 2 =1 6 5 4 3 2 1 0 For example, the binary number 00101001B = 41. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 40 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 3.6.2.5. Tco Interpretation Tco is specified as having an 8-bit magnitude with an additional sign bit and a scalar bit (Tc_cfg). When the scalar bit is set, the signed Tco is multiplied by 8. Tco Resolution: Tco Range: o 0.175 μV/V/ C o ± 44.6 μV/V/ C (input referred) (input referred) If the scaling bit is used, then the above resolution and range are scaled by 8 to give the following results: Tco Scaled Resolution: Tco Scaled Range: o 1.40 μV/V/ C (input referred) o ± 357 μV/V/ C (input referred) 3.6.2.6. Tcg Interpretation Tcg is specified as an 8-bit magnitude with an additional sign bit (Tc_cfg). Tcg Resolution: Tcg Range: o 17.0 ppm/ C o ±4335 ppm/ C 3.6.2.7. SOT Interpretation nd SOT is a 2 order term that can apply to one and only one of the following: bridge non-linearity correction, Tco non-linearity correction, or Tcg non-linearity correction. As it applies to bridge non-linearity correction: Resolution: 0.25% @ full scale Range: +25% @ full scale to -25% @ full scale (Saturation in internal arithmetic will occur at greater negative nonlinearities.) As it applies to Tcg: Resolution: 0.3 ppm/( C) o 2 Range: +/- 38ppm/( C) o 2 As it applies to Tco: 2 settings are possible. It is possible to scale the effect of SOT by 8. If Tc_cfg[1] is set, then both Tco and SOT’s contribution to Tco are multiplied by 8. Resolution at unity scaling: 1.51nV/V/( C) (input referred) o 2 Range: +/- 0.192V/V/( C) (input referred) o 2 Resolution at 8x scaling: 12.1nV/V/( C) (input referred) o 2 Range: +/- 1.54V/V/( C) (input referred) o Data Sheet October 9, 2013 2 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 41 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 3.7. Reading EEPROM Contents The contents of the entire EEPROM memory can be read out using the Read EEPROM command (00 HEX). This command causes the ZSC31015 to output consecutive bytes on the ZACwire™. After each transmission, the EEPROM contents are shifted by 8 bits. The bit order of these bytes is given in Table 3.11. Table 3.11 EEPROM Read Order Bit 7 Bit 6 Bit 5 Bit 4 Byte 1 Bit 3 Bit 2 Bit 1 Bit 0 Offset_B[7:0] Byte 2 Gain_T[1:0] Byte 3 Offset_T[1:0] Gain_T[7:2] Byte 4 TSETL[1:0] Offset_T[7:2] Offset_B[13:8] Byte 5 Tcg[2:0] TSETL[6:2] Byte 6 Tco[2:0] Tcg[7:3] Byte 7 Tc_cfg[2:0] Tco[7:3] Byte 8 SOT[7:0] Byte 9 Lock[0] Diag_cfg[2:0] Byte 10 SOT_cfg[3:0] Up_Clip_Lim[5:0] Byte 11 Lock[2 :1] Low_Clip_Lim[6:0] Byte 12 Cust_ID0[7:0] Byte 13 Cust_ID1[7:0] Byte 14 Cust_ID2[7:0] Byte 15 Signature[7:0] Byte 16 A2D_Offset[0] Byte 17 JFET_cfg[0] Byte 18 1V_Trim[3:0] ** Update_Rate[1:0] Up_Clip_Lim[6] Osc_Trim[2:0] ** Output Select[1:0] A2D_Offset[3:1] Gain_B[6:0] JFET_cfg[1] Byte 19 Gain_B[14:7] Byte 20 A5HEX * SOT_cfg/Pamp_Gain ** 1V_Trim/JFET_Trim Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 42 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 4 Application Circuit Examples The minimum output analog load resistor is RL= 5k. This optional load resistor can be configured as a pull-up or pull-down. If it is configured as a pull-down, it cannot be part of the module to be calibrated because this would TM prevent proper operation of the ZACwire . If a pull-down load is desired, it must be added to system after module calibration. There is no output load capacitance needed. EEPROM contents: OUTPUT_select, Config_JFET_Regulation, 1V_Trim/JFET-Trim. 4.1. Three-Wire Rail-to-Rail Ratiometric Output This example shows an application circuit for rail-to-rail ratiometric voltage output configuration with temperature compensation via an external diode. The same circuitry is applicable for a 0 to 1V absolute analog output. Figure 4.1 Rail-to-Rail Ratiometric Voltage Output – Temperature Compensation via External Diode Vsupply +2.7 to +5.5 V 1 Bsink VSS 8 2 VBP SigTM 7 3 ExtTemp 4 VBN Optional Bsink OUT VDD 6 Vgate 5 ZSC31015 0.1 F Ground The optional bridge sink allows a power savings of bridge current. The output voltage can be either Rail-to-rail ratiometric analog output VDD(=Vsupply). 0 to 1V absolute analog output. The absolute voltage output reference is trimmable 1V (+/-3mV) in the 1V Output Mode via a 4-bit EEPROM field. See section 2.4.3). Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 43 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 4.2. Absolute Analog Voltage Output The figure below shows an application circuit for an absolute voltage output configuration with temperature compensation via internal temperature PTAT and external JFET regulation for all industry standard applications. Figure 4.2 Absolute Analog Voltage Output – Temperature Compensation via Internal Temperature PTAT with External JFET Regulation BSS169 S 1 Bsink VSS 8 2 VBP SigTM 7 3 ExtTemp 4 VBN Optional Bsink D Vsupply +5.5 to +30 V OUT VDD 6 Vgate 5 ZSC31015 0.1 F Ground The output signal range can be one of the following options: 0 to 1 V analog output. The absolute voltage output reference is trimmable: 1 V (+/-3 mV) in the 1 V Output Mode via a 4-bit EEPROM field (see section 2.4.3). Rail-to-rail analog output. The on-chip reference for the JFET regulator block is trimmable: 5 V (±15 mV) in the Ratiometric Output Mode via a 4-bit EEPROM field. (See section 2.4.3). Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 44 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 4.3. Three-Wire Ratiometric Output with Over-Voltage Protection The figure below shows an application circuit for a ratiometric output configuration with temperature compensation via an internal diode. In this application, the JFET is used for voltage protection. JFET_cfg (16:15) in the EEPROM are configured to 5.5V. There is an additional maximum error of 8mV caused by the non-zero rds(on) of the limiter JFET. Figure 4.3 Ratiometric Output, Temperature Compensation via Internal Diode J107 Vishay S 1 Bsink VSS 8 2 VBP SigTM 7 3 ExtTemp 4 VBN Optional Bsink D Vsupply +5.0 to +5.5 V OUT VDD 6 Vgate 5 ZSC31015 0.1 F Ground 4.4. Digital Output For all three circuits, the output signal can also be digital. Depending on the output select bits, the bridge signal or the bridge signal and temperature signal are sent. For the digital output, no load resistor or load capacity is necessary. No pull down resistor is allowed. If a line resistor or pull-up resistor is used, the requirement for the rise time must be met (< 5 s). The ZSC31015 output includes an internal pull up resistor of about 30 k. The digital output can easily be read by firmware from a microcontroller, and ZMDI can provide the customer with software for developing the interface. 4.5. Output Resistor/Capacitor Limits The limits for external components depend on the programmed output mode: Pure Analog Output Mode (calibration is done before): The only limit is the minimum load resistance of 5 k. Pure Digital Output Mode with end-of-line calibration: The RC time constant of the ZACwire™ line must have a rise time < 5 µs. Analog output with digital communication during calibration: The RC time constant of the ZACwire™ line must have a rise time < 5 µs. Warning: Any series line resistance forms a voltage divider in conjunction with the pull-up load device. If a series line resistance is needed, choose a low value relative to the pull-up load device. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 45 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 5 EEPROM Restoration If needed, the default settings for the ZSC31015 (see Table 3.5) can be reprogrammed as described in section 3. The following sections describe EEPROM content validation and handling during and/or after system assembly. Important: During the sawing and dicing process, there is a possibility of the EEPROM contents flipping, and prevention cannot be guaranteed. This is primarily a concern for the factory trim settings, which are customized to each part. The EEPROM default values programmed during the different test levels have been selected so that customer has the option to refresh/reprogram trim bits that might have flipped during sawing or dicing. Important: The EEPROM lock is stored in the bit range 105:103. A value of 6 HEX or 3HEX will lock the EEPROM forever by disabling the charge pump needed for EEPROM writing. The complete contents can also be validated using the EEPROM signature stored in bits [151:144], (see “Signature” in Table 3.5). 5.1. Default EEPROM Contents During the wafer level test (wafer/dice delivery) and during final test for SOP8 packaged parts, the EEPROM is programmed with the default values listed in the Table 3.5. During the wafer level test, the Osc_trim bits [2:0] and 1V_Trim/JFET_Trim trim bits [6:3] are set to die-specific values. 5.1.1. Osc_Trim The oscillator frequency is trimmed to a value of 512kHz±20% using the Osc_Trim bit setting. The 3-bit setting is copied twice to Cust_ID1[134:132] and [130:128] and then a third time to Cust_ID2[138:136] to ensure the factory settings are retained so that the customer can reprogram these values in the Osc_Trim bit if needed. Based on the most probable trimming, the default values for the Osc_Trim bits are always set to 0 HEX during factory testing to guarantee communication even if bits have flipped. 5.1.2. 1V_Trim/JFET_Trim The 5V reference for the JFET regulation is factory trimmed during the final test to 5V±15mV using the 1V_Trim/ JFET_Trim bit setting. The 4-bit setting stored in EEPROM bits [6:3] is copied twice to the Cust_ID0 bits [127:124] and [123:120] to ensure the factory settings are retained so that the customer can reprogram these values in the 1V_Trim/JFET_Trim bits if needed. 5.2. EEPROM Restoration Procedure After module assembly, the EEPROM content should be refreshed. If JFET regulation is not used for the user’s application and optimized response time is not an important criterion, write the default values shown in Table 3.5 to the EEPROM bit range [143:7] and retain the existing values in the bit range [6:0]. If JFET regulation or optimized response time is required, the bit restoration procedure shown in the flow chart in Figure 5.1 must be used to keep the factory settings programmed during the testing. If customer oscillator trimming is required, see ZSC31015_Tech_Notes_JFET_and_Osc_Trimming_revX.X .pdf for instructions.) Note: The EEPROM signature is re-calculated and updated after every EEPROM writing. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 46 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Figure 5.1 EEPROM Validation and Restoration Procedure Start CM Restore Factory Trimming? N Y Read EEPROM Check Osc_Trim bits [130:128]=[138:136] Check Osc_Trim bits [134:132]=[130:128] N N Y Y N Keep bits [6:3] Write [134:132] to [2:0] Check JFET_Trim bits [123:120]=[127:124] Check JFET_Trim bits [6:3]=[127:124] N Y Write [130:128] to [2:0] Write [134:132] to [2:0] Y Check Osc_Trim bits [134:132]=[138:136] Check JFET_Trim bits [6:3]=[123:120] N Y Write [123:120] to[6:3] Perform New Osc_Trim N Y Keep bits [6:3] Perform New JFET_Trim Write EEPROM default values [143:7] Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 47 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 6 Pin Configuration and Package The standard package of the ZSC31015 is an SOP-8 (3.81 mm / 150 mil body) with a lead-pitch 1.27 mm / 50 mil. Table 6.1 Storage and Soldering Conditions for SOP-8 Package Parameter Symbol Conditions Maximum Storage Temperature Tmax_storage Less than 10hrs, before mounting Minimum Storage Temperature: Tmin_storage Store in original packing only Tdrybake Less than100 hrs total, before mounting 125 C Less than 30s (IPC/JEDEC-STD-020 Standard) 260 C Maximum Dry-Bake Temperature Soldering Peak Temperature Tpeak Min Typical Max Units 150 C C -50 Figure 6.1 ZSC31015 Pin-Out Diagram Table 6.2 Bsink 1 8 VSS VBP 2 7 SigTM ExtTemp 3 6 VDD VBN 4 5 Vgate ZSC31015 Pin Configuration Pin No. Name Description 1 Bsink Optional ground connection for bridge ground; used for power savings 2 VBP Positive bridge connection 3 ExtTemp External diode connection 4 VBN Negative bridge connection 5 Vgate Gate control for external JFET regulation/over-voltage protection 6 VDD Supply voltage (2.7 to 5.5 V) 7 Sig™ ZACwire™ interface (analog out, digital out, calibration interface) 8 VSS Ground supply Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 48 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 7 ESD/Latch-Up-Protection All pins have an ESD protection of >4000V and a latch-up protection of 100 mA or of +8V/ –4V (to VSS/VSSA). ESD protection referenced to the Human Body Model is tested with devices in SOP-8 packages during product qualification. The ESD test follows the Human Body Model with 1.5kΩ/100pF based on MIL 883, Method 3015.7. 8 Test The test program is based on this datasheet. The final parameters that are tested during series production are listed in the tables of section 1. The digital part of the IC includes a scan path, which can be activated and controlled during wafer test. Further test support for testing of the analog parts on wafer level is included in the DSP. 9 Quality and Reliability A reliability investigation according to the in-house non-automotive standard has been performed. 10 Customization For high-volume applications, which require an upgraded or downgraded functionality compared to the ZSC31015, ZMDI can customize the circuit design by adding or removing certain functional blocks. For this customization, ZMDI has a considerable library of sensor-dedicated circuitry blocks, which enable ZMDI to provide a custom solution quickly. Please contact ZMDI for further information. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 49 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 11 Part Ordering Codes Please contact ZMDI Sales for additional information. Sales Code Description Package ZSC31015EEB ZSC31015 Die — Temperature range: -50°C to +150°C Unsawn on Wafer ZSC31015EEC ZSC31015 Die— Temperature range: -50°C to +150°C Sawn on Wafer Frame ZSC31015EEG1-R ZSC31015 SOP8 (150 mil) — Temperature range: -50°C to +150°C Reel ZSC31015EEG1-T ZSC31015 SOP8 (150 mil) — Temperature range: -50°C to +150°C Tube ZSC31015EAB ZSC31015 Die — Temperature range: -40°C to +125°C Unsawn on Wafer ZSC31015EAC ZSC31015 Die— Temperature range: -40°C to +125°C Sawn on Wafer Frame ZSC31015EAG1-R ZSC31015 SOP8 (150 mil) — Temperature range: -40°C to +125°C Reel ZSC31015EAG1-T ZSC31015 SOP8 (150 mil) — Temperature range: -40°C to +125°C Tube ZSC31015EIB ZSC31015 Die— Temperature range: -25°C to +85°C Unsawn on Wafer ZSC31015EIC ZSC31015 Die — Temperature range: -25°C to +85°C Sawn on Wafer Frame ZSC31015EIG1-R ZSC31015 SOP8 (150 mil) — Temperature range: -25°C to +85°C Reel ZSC31015EIG1-T ZSC31015 SOP8 (150 mil) — Temperature range: -25°C to +85°C Tube ZSC31015KIT ZSC31015 ZACwire™ SSC Evaluation Kit: Communication Board, SSC Board, Sensor Replacement Board, Evaluation Software, USB Cable, 5 IC Samples (SOP8) Kit Contact ZMDI Sales for support and sales of ZMDI’s ZSC31015 Mass Calibration System. 12 Related Documents Note: Rev_X_xy refers to the current revision of the document. Document File Name ZACwire™ SSC Evaluation Kit Documentation ZACwire_SSC_Evaluation_Kit_Rev_X_xy.pdf ZSC31015 Die Dimensions and Pad Coordinates** ZSC31015_Tech_Notes_Die_Pads_Rev_X_xy.pdf SSC Kits Feature Sheet * (includes ordering codes and prices) SSC_Evaluation_Kits_FeatureSheet_Rev_rev_X_xy.pdf Visit the ZSC31015 product page (www.zmdi.com/zsc31015) on ZMDI’s website www.zmdi.com or contact your nearest sales office for the latest version of these documents. * Documents marked with an asterisk (*) can be found on the Evaluation Tools page (www.zmdi.com/ssc-tools). ** Documents marked with two asterisks (**) are available on request (see page 53). Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 50 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 13 Definitions of Acronyms Term Description ADC Analog-to-Digital Converter AFE Analog Front-End BUF Buffer CM Command Mode CMC Calibration Microcontroller DAC Digital-to-Digital Converter DNL Differential Nonlinearity DSP Digital Signal Processor DUT Device Under Test ESD Electrostatic Discharge FSO Full-Scale Output INL Integrated Nonlinearity LSB Least Significant Bit MUX Multiplexer NOM Normal Operation Mode OWI One-Wire Interface POC Power-On Clear POR Power-On Reset Level PSRR Power Supply Rejection Ratio PTAT Proportional To Absolute Temperature RM Raw Mode SOT Second Order Term Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 51 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features 14 Document Revision History Revision Date Description 1.40 February 24, 2009 Revision to Byte 16 in Table 3.11. Revision to add an explanation for default setting in Table 3.5. Revision to “Lower Output Voltage Limit” specification in section 1.3.5. Revisions in sections 2.4.3 and 2.5.1 to text regarding regulator set point and optimal reference trim, including text about methods for preserving factory settings. Revision to caption for Figure 3.2 to clarify that timing is typical. Revision to text below Table 3.2 regarding minimum and maximum baud rate. Added note below Table 3.3 clarifying that timing is typical. Revisions to the default settings column and explanations for the Cust_ID0 and Cust_ID1 EEPROM words in Table 3.5. Addition of section 5 to explain methods for restoration of EEPROM settings. 1.50 May 14, 2009 Revised conditions for “Overall Ratiometricity Error” and “Overall Accuracy – Analog” specifications in section 1.3.9. 1.60 June 10, 2009 Added “Document Revision History” table. 1.70 March 29, 2010 Corrected start-up window time 1.5 to 3ms. This change applies only to rev C1 Silicon (marked as ZSC31015Cxx.) and higher. Stop bit definition is replaced by stop time definition. Relocated specs from Table 1.9 and deleted Table 1.9. 1.73 May 11, 2010 Added footnote to pages 2, 3, and 14 clarifying that the ZSC31015 is not AEC-Q100qualified. 1.74 July 19, 2010 Added special measurement information to Table 3.2; revised precondition for equation (1). 1.80 July 27, 2010 Revised product name from ZMD31015 to ZSC31015. 1.90 March 24, 2011 Added EEPROM specifications to section 1.3 “Electrical Parameters.” Added table 6.1 “Storage and Soldering Conditions” to section 6 “Pin Configuration and Package.” Updated trim tolerances in sections 4.1and 4.2. Updated ZMDI contact information. 1.91 October 8, 2011 Revisions in section 1.3.4. Addition of part ordering numbers for all available temperature ranges to section 11. Update for sales contact information to add ZMDI’s Korea office. Revision of product title. 1.92 January 12, 2012 Removed requirement of fastest update rate for analog output mode (applied to previous IC revision). Updated contact information for the USA. 2.00 October 28, 2012 Updates to contact information and part ordering numbers. 2.10 October 9, 2013 Update to section 1.2 to add new minimum specification for output load capacitance. Update to section 1.3.9 for tSTA maximum specification. Updates to contact information and imagery for cover and headers. Updates to part order options. Updates to related documents. Data Sheet October 9, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 52 of 53 ZSC31015 RBicdLite™ Analog Output Sensor Signal Conditioner w/ Diagnostic Features Sales and Further Information www.zmdi.com [email protected] Zentrum Mikroelektronik Dresden AG Global Headquarters Grenzstrasse 28 01109 Dresden, Germany ZMD America, Inc. 1525 McCarthy Blvd., #212 Milpitas, CA 95035-7453 USA Central Office: Phone +49.351.8822.0 Fax +49.351.8822.600 USA Phone +855.275.9634 Phone +408.883.6310 Fax +408.883.6358 European Technical Support Phone +49.351.8822.7.772 Fax +49.351.8822.87.772 DISCLAIMER: This information applies to a product under development. Its characteristics and specifications are subject to change without notice. Zentrum Mikroelektronik Dresden AG (ZMD AG) assumes no obligation regarding future manufacture unless otherwise agreed to in writing. The information furnished hereby is believed to be true and accurate. However, under no circumstances shall ZMD AG be liable to any customer, licensee, or any other third party for any special, indirect, incidental, or consequential damages of any kind or nature whatsoever arising out of or in any way related to the furnishing, performance, or use of this technical data. ZMD AG hereby expressly disclaims any liability of ZMD AG to any customer, licensee or any other third party, and any such customer, licensee and any other third party hereby waives any liability of ZMD AG for any damages in connection with or arising out of the furnishing, performance or use of this technical data, whether based on contract, warranty, tort (including negligence), strict liability, or otherwise. European Sales (Stuttgart) Phone +49.711.674517.55 Fax +49.711.674517.87955 Data Sheet October 9, 2013 Zentrum Mikroelektronik Dresden AG, Japan Office 2nd Floor, Shinbashi Tokyu Bldg. 4-21-3, Shinbashi, Minato-ku Tokyo, 105-0004 Japan ZMD FAR EAST, Ltd. 3F, No. 51, Sec. 2, Keelung Road 11052 Taipei Taiwan Phone +81.3.6895.7410 Fax +81.3.6895.7301 Phone +886.2.2377.8189 Fax +886.2.2377.8199 Zentrum Mikroelektronik Dresden AG, Korea Office U-space 1 Building 11th Floor, Unit JA-1102 670 Sampyeong-dong Bundang-gu, Seongnam-si Gyeonggi-do, 463-400 Korea Phone +82.31.950.7679 Fax +82.504.841.3026 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 2.10 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 53 of 53